When a new ACL group is created its region (ACL) list is initially
empty. Thus, the call to mlxsw_sp_acl_tcam_group_update() would
basically invalidate an already invalid (non-existent) group.
Remove the unnecessary call and make the function symmetric to its del()
counterpart.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently creates empty ACL groups, binds them to the
requested port and then fills them with actual ACLs that point to TCAM
regions.
However, empty ACL groups are considered invalid and upcoming firmware
versions are going to forbid their binding.
Work around this limitation by only performing the binding after the
first ACL was added to the group.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to set some of the fields within 'mbox_config_profile',
since they are reserved and capability mask should be set to zero.
Signed-off-by: Tal Bar <talb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the opcodes don't use in, out or both mboxes. In such cases, the
mbox address is a reserved field and FW expects it to be zero.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cppcheck report:
[drivers/net/ethernet/cortina/gemini.c:543]: (error) Memory leak: skb_tab
Signed-off-by: Igor Pylypiv <igor.pylypiv@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the optional regulator is deferred, we must release some resources.
They will be re-allocated when the probe function will be called again.
Fixes: 6eacf31139 ("ethernet: arc: Add support for Rockchip SoC layer device tree bindings")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
... and drop the pointless checks - sys_truncate() itself
might've lacked the check when that stuff was first written,
but it has already grown one by the time that stuff went into
mainline.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Back in January 1998, in 2.1.79 check_pending() got taken out and shot.
Users in arch/sparc and arch/sparc64 got converted away from it. One
of the externs (in arch/sparc) was taken out at the same time. Two
other (in arch/sparc64/kernel/sys_sparc{,32}.c) got stuck. The one in
sys_sparc32.c was quietly removed 6 years later by an unrelated
commit. The last one kept shambling until now. It's time to end
that depravity, let's bury the body...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Commit c6202ca764 ("sparc64: Add auxiliary vectors to report
platform ADI properties") adds auxiliary vectors to report ADI
capabilities on sparc64 platform only. This needs to be uniform
across 64-bit and 32-bit. This patch makes the same vectors
available on 32-bit as well.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Khalid Aziz <khalid@gonehiking.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are needed to use the n_gsm driver for TS 27.010 UART
multiplexing. Note that support for the OOB wake gpio is still
missing so the UART is not yet usable for n_gsm.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Configure MDM6600 USB PHY.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have a USB OCHI PHY on port 1 for mdm6600. Port 2 is using transceiverless
logic (TLL) for USB EHCI for w3glte modem.
Let's also fix the node name to use usb-phy while at it.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds syscon property for specifying soc-glue core into
device-tree of PXs2 SoC.
Currently, soc-glue core is used for changing the state of S/PDIF
signal output pin to signal output state or Hi-Z state.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds syscon property for specifying soc-glue core into
device-tree of LD11/LD20 SoC.
Currently, soc-glue core is used for changing the state of S/PDIF
signal output pin to signal output state or Hi-Z state.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Match the new compatible string in the control module driver. The base
infra maps the required syscon ranges and clock registers if available.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Control module can have multiple instances in a system, each with separate
address space and features. Add base support for these auxiliary instances,
with support for syscon and clock mappings under them.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The current code performs unneeded free. Remove the redundant skb freeing
during the error path.
Fixes: 1555d204e7 ("devlink: Support for pipeline debug (dpipe)")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all callers want the GPU error to handled in the same way, so expose
a control parameter. In the first instance, some callers do not want the
heavyweight error capture so add a bit to request the state to be
captured and saved.
v2: Pass msg down to i915_reset/i915_reset_engine so that we include the
reason for the reset in the dev_notice(), superseding the earlier option
to not print that notice.
v3: Stash the reason inside the i915->gpu_error to handover to the direct
reset from the blocking waiter.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320100449.1360-2-chris@chris-wilson.co.uk
If the GPU is stuck waiting for an event or for a semaphore, we need to
reset the GPU in order to recover. We have to tell the reset routine
which engines we want reset, but we were still using the old interface
and declaring it as "not-fatal".
Fixes: 14b730fcb8 ("drm/i915/tdr: Prepare error handler to accept mask of hung engines")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320100449.1360-1-chris@chris-wilson.co.uk
When changing the default values for guc_log_level, we accidentally left
the log enabled on non-guc platforms. Let's fix that.
v2: Define the levels used and remove (now obsolete) comments (Chris)
v3: Use "IS" rather than "TO" for booleans (Chris)
Fixes: 9605d1ce7c ("drm/i915/guc: Default to non-verbose GuC logging")
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320115517.20423-1-michal.winiarski@intel.com
The mlx5 driver calls ida_pre_get() in a loop for no readily apparent
reason. The driver uses ida_simple_get() which will call ida_pre_get()
by itself and there's no need to use ida_pre_get() unless using
ida_get_new().
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xref_xtal clock is used by twl6040 as mclk. It is needed for the HPPLL
internally.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clock is directly sourced from sys_clkin, and provides an external
output clock for (typically) TWL6040 chip.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pad configuration area under control module wkup has some miscellaneous
config registers, that are not pinmux related. Add a separate area for
these, and add support for syscon / clocks under this new area.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pad configuration area under control module wkup has some miscellaneous
config registers, that are not pinmux related.
Add new compatible string for this section of control module.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Johan Hedberg says:
====================
Here are a few more important Bluetooth driver fixes for the 4.16
kernel.
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ICL 11 has a greater number of maximum subslices. This patch
reflects this.
v2: GEN11 updates to MCR_SELECTOR (Oscar)
v3: Copypasta error in the new defines (Lionel)
Bspec: 21139
BSpec: 21108
Signed-off-by: Kelvin Gardiner <kelvin.gardiner@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com> (v1)
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> (v1)
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180316121456.11577-3-mika.kuoppala@linux.intel.com
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Icelake 11 has one vebox and two vdboxes (0 and 2).
Bspec: 21140
v2: Split out in two (Daniele)
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180316121456.11577-2-mika.kuoppala@linux.intel.com
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
In Gen11, the Video Decode engines (aka VDBOX, aka VCS, aka BSD) and the
Video Enhancement engines (aka VEBOX, aka VECS) could be fused off. Also,
each VDBOX and VEBOX has its own power well, which only exist if the
related engine exists in the HW.
Unfortunately, we have a Catch-22 situation going on: we need the blitter
forcewake to read the register with the fuse info, but we cannot initialize
the forcewake domains without knowin about the engines present in the HW.
We workaround this problem by allowing the initialization of all forcewake
domains and then pruning the fused off ones, as per the fuse information.
Bspec: 20680
v2: We were shifting incorrectly for vebox disable (Vinay)
v3: Assert mmio is ready and warn if we have attempted to initialize
forcewake for fused-off engines (Paulo)
v4:
- Use INTEL_GEN in new code (Tvrtko)
- Shorter local variable (Tvrtko, Michal)
- Keep "if (!...) continue" style (Tvrtko)
- No unnecessary BUG_ON (Tvrtko)
- WARN_ON and cleanup if wrong mask (Tvrtko, Michal)
- Use I915_READ_FW (Michal)
- Use I915_MAX_VCS/VECS macros (Michal)
v5: Rebased by Rodrigo fixing conflicts on top of:
"drm/i915: Simplify intel_engines_init"
v6: Fix v5. Remove info->num_rings. (by Oscar)
v7: Rebase (Rodrigo).
v8:
- s/intel_device_info_fused_off_engines/
intel_device_info_init_mmio (Chris)
- Make vdbox_disable & vebox_disable local variables (Chris)
v9:
- Move function declaration to intel_device_info.h (Michal)
- Missing indent in bit fields definitions (Michal)
- When RC6 is enabled by BIOS, the fuse register cannot be read until
the blitter powerwell is awake. Shuffle where the fuse is read, prune
the forcewake domains after the fact and change the commit message
accordingly (Vinay, Sagar, Chris).
v10:
- Improved commit message (Sagar)
- New line in header file (Sagar)
- Specify the message in fw_domain_reset applies to ICL+ (Sagar)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180316121456.11577-1-mika.kuoppala@linux.intel.com
[Mika: soothe checkpatch on commit msg]
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
USB1 port is micro-AB type and can function as peripheral
as well as host. Enable dual-role mode for USB1.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need the CPCAP MFD and regulator built-in for UART console to work,
the rest can be loadable modules. Note that users probably want to also
enable serial 8250_OMAP that is not yet enabled by default.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch exposes synproxy information per-conntrack. Moreover, send
sequence adjustment events once server sends us the SYN,ACK packet, so
we can synchronize the sequence adjustment too for packets going as
reply from the server, as part of the synproxy logic.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Now that SPDX identifiers are in place, remove the boilerplate or
references.
The change in timings.c has been acked by the author.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Link: https://lkml.kernel.org/r/20180314212030.668321222@linutronix.de
Add SPDX identifiers to files
- which contain an explicit license boiler plate or reference
- which do not contain a license reference and were not updated in the
initial SPDX conversion because the license was deduced by the scanners
via EXPORT_SYMBOL_GPL as GPL2.0 only.
[ tglx: Moved adding identifiers from the patch which removes the
references/boilerplate ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Link: https://lkml.kernel.org/r/20180314212030.668321222@linutronix.de
Use the proper SPDX-Identifier format.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Link: https://lkml.kernel.org/r/20180314212030.492674761@linutronix.de