Commit graph

379,179 commits

Author SHA1 Message Date
David Lechner
0e58d0cdb3 Bluetooth: hci_ll: Add optional nvmem BD address source
This adds an optional nvmem consumer to get a BD address from an external
source. The BD address is then set in the Bluetooth chip after the
firmware has been loaded.

This has been tested working with a TI CC2560A chip (in a LEGO MINDSTORMS
EV3).

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-12-13 09:21:20 +01:00
David Lechner
aa09939869 Bluetooth: hci_ll: add support for setting public address
This adds support for setting the public address on Texas Instruments
Bluetooth chips using a vendor-specific command.

This has been tested on a CC2560A chip. The TI wiki also indicates that
this command should work on TI WL17xx/WL18xx Bluetooth chips.

During review, there was some question as to the correctness of the byte
swapping since TI's documentation is not clear on this matter. This can
be tested with the btmgmt utility from bluez. The adapter must be powered
off to change the address. If the baswap() is omitted, address is reversed.

In case there is a issue in the future, here is the output of btmon during
the command `btmgmt public-addr 00:11:22:33:44:55`:

Bluetooth monitor ver 5.43
= Note: Linux version 4.15.0-rc2-08561-gcb132a1-dirty (armv5tejl)      0.707043
= Note: Bluetooth subsystem version 2.22                               0.707091
= New Index: 00:17:E7:BD:1C:8E (Primary,UART,hci0)              [hci0] 0.707106
@ MGMT Open: btmgmt (privileged) version 1.14                 {0x0002} 0.707124
@ MGMT Open: bluetoothd (privileged) version 1.14             {0x0001} 0.707137
@ MGMT Open: btmon (privileged) version 1.14                  {0x0003} 0.707540
@ MGMT Command: Set Public Address (0x0039) plen 6    {0x0002} [hci0] 11.167991
        Address: 00:11:22:33:44:55 (CIMSYS Inc)
@ MGMT Event: Command Complete (0x0001) plen 7        {0x0002} [hci0] 11.175681
      Set Public Address (0x0039) plen 4
        Status: Success (0x00)
        Missing options: 0x00000000
@ MGMT Event: Index Removed (0x0005) plen 0           {0x0003} [hci0] 11.175757
@ MGMT Event: Index Removed (0x0005) plen 0           {0x0002} [hci0] 11.175757
@ MGMT Event: Index Removed (0x0005) plen 0           {0x0001} [hci0] 11.175757
= Open Index: 00:17:E7:BD:1C:8E                                [hci0] 11.176807
< HCI Command: Vendor (0x3f|0x0006) plen 6                     [hci0] 11.176975
        00 11 22 33 44 55                                .."3DU
> HCI Event: Command Complete (0x0e) plen 4                    [hci0] 11.188260
      Vendor (0x3f|0x0006) ncmd 1
        Status: Success (0x00)
...
< HCI Command: Read Local Version Info.. (0x04|0x0001) plen 0  [hci0] 11.189859
> HCI Event: Command Complete (0x0e) plen 12                   [hci0] 11.190732
      Read Local Version Information (0x04|0x0001) ncmd 1
        Status: Success (0x00)
        HCI version: Bluetooth 2.1 (0x04) - Revision 0 (0x0000)
        LMP version: Bluetooth 2.1 (0x04) - Subversion 6431 (0x191f)
        Manufacturer: Texas Instruments Inc. (13)
< HCI Command: Read BD ADDR (0x04|0x0009) plen 0               [hci0] 11.191027
> HCI Event: Command Complete (0x0e) plen 10                   [hci0] 11.192101
      Read BD ADDR (0x04|0x0009) ncmd 1
        Status: Success (0x00)
        Address: 00:11:22:33:44:55 (CIMSYS Inc)
...

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-12-13 00:28:42 +01:00
David Lechner
c30b93eade Bluetooth: hci_ll: Add endianness conversion when setting baudrate
This adds an endianness conversion when setting the baudrate using a
vendor-specific command. Otherwise, bad things might happen on a big-
endian system.

Suggested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-12-13 00:28:41 +01:00
David Lechner
7c6ca1201e Bluetooth: hci_ll: add constant for vendor-specific command
This adds a #define for the vendor-specific HCI command to set the
baudrate instead of using the bare 0xff36 multiple times.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-12-13 00:28:41 +01:00
David Lechner
d54fdcf924 Bluetooth: serdev: hci_ll: Wait for CTS instead of using msleep
When a TI Bluetooth chip is reset, it takes about 100ms for the RTS line of
the chip to deassert. For my use case with a TI CC2560A chip, this delay
was not long enough and caused the local UART to never transmit at all (TI
AM1808 SoC UART2).

We can wait for the CTS signal using serdev_device_wait_for_cts() instead
of trying to guess using msleep().

Also changed the comment to be more informative while we are touching this
code.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-12-13 00:28:41 +01:00
David Lechner
059fb82307 Bluetooth: hci_ll: remove \n from kernel messages
The bt_* printk macros include a \n already, so we don't need extra ones
here.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-12-13 00:28:41 +01:00
Hans de Goede
b4cdaba274 Bluetooth: btsdio: Do not bind to non-removable BCM43341
BCM43341 devices soldered onto the PCB (non-removable) always (AFAICT)
use an UART connection for bluetooth. But they also advertise btsdio
support on their 3th sdio function, this causes 2 problems:

1) A non functioning BT HCI getting registered

2) Since the btsdio driver does not have suspend/resume callbacks,
mmc_sdio_pre_suspend will return -ENOSYS, causing mmc_pm_notify()
to react as if the SDIO-card is removed and since the slot is
marked as non-removable it will never get detected as inserted again.
Which results in wifi no longer working after a suspend/resume.

This commit fixes both by making btsdio ignore BCM43341 devices
when connected to a slot which is marked non-removable.

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-12-13 00:28:41 +01:00
Hans de Goede
c23fae1111 Bluetooth: hci_bcm: Add support for BCM2E72
The Asus T100HA laptop uses an ACPI HID of BCM2E72 for the bluetooth
part of the SDIO bcm43340 wifi/bt combo chip.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-12-13 00:28:41 +01:00
Loic Poulain
67b8fbead4 Bluetooth: btqcomsmd: Fix skb double free corruption
In case of hci send frame failure, skb is still owned
by the caller (hci_core) and then should not be freed.

This fixes crash on dragonboard-410c when sending SCO
packet. skb is freed by both btqcomsmd and hci_core.

Fixes: 1511cc750c ("Bluetooth: Introduce Qualcomm WCNSS SMD based HCI driver")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-12-13 00:28:41 +01:00
Lukas Wunner
d73e172816 Bluetooth: hci_serdev: Init hci_uart proto_lock to avoid oops
John Stultz reports a boot time crash with the HiKey board (which uses
hci_serdev) occurring in hci_uart_tx_wakeup().  That function is
contained in hci_ldisc.c, but also called from the newer hci_serdev.c.
It acquires the proto_lock in struct hci_uart and it turns out that we
forgot to init the lock in the serdev code path, thus causing the crash.

John bisected the crash to commit 67d2f8781b ("Bluetooth: hci_ldisc:
Allow sleeping while proto locks are held"), but the issue was present
before and the commit merely exposed it.  (Perhaps by luck, the crash
did not occur with rwlocks.)

Init the proto_lock in the serdev code path to avoid the oops.

Stack trace for posterity:

Unable to handle kernel read from unreadable memory at 406f127000
[000000406f127000] user address but active_mm is swapper
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Hardware name: HiKey Development Board (DT)
Call trace:
 hci_uart_tx_wakeup+0x38/0x148
 hci_uart_send_frame+0x28/0x38
 hci_send_frame+0x64/0xc0
 hci_cmd_work+0x98/0x110
 process_one_work+0x134/0x330
 worker_thread+0x130/0x468
 kthread+0xf8/0x128
 ret_from_fork+0x10/0x18

Link: https://lkml.org/lkml/2017/11/15/908
Reported-and-tested-by: John Stultz <john.stultz@linaro.org>
Cc: Ronald Tschalär <ronald@innovation.ch>
Cc: Rob Herring <rob.herring@linaro.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-12-13 00:28:41 +01:00
Hans de Goede
e7232d184c Bluetooth: btusb: Fix BT_HCIBTUSB_AUTOSUSPEND Kconfig option name
Fix: drivers/bluetooth/Kconfig:35:warning: multi-line strings not
supported warning.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-12-13 00:28:41 +01:00
Hans de Goede
eff2d68ca7 Bluetooth: btusb: Add a Kconfig option to enable USB autosuspend by default
On many laptops the btusb device is the only USB device not having USB
autosuspend enabled, this causes not only the HCI but also the USB
controller to stay awake, together using aprox. 0.4W of power.

Modern ultrabooks idle around 6W (at 50% screen brightness), 3.5W for
Apollo Lake devices. 0.4W is a significant chunk of this (7 / 11%).

The btusb driver already contains code to allow enabling USB autosuspend,
but currently leaves it up to the user / userspace to enable it. This
means that for most people it will not be enabled, leading to an
unnecessarily high power consumption.

Since enabling it is not entirely without risk of regressions, this
commit adds a Kconfig option so that Linux distributions can choose to
enable it by default. This commit also adds a module option so that when
distros receive bugs they can easily ask the user to disable it again
for easy debugging.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-12-13 00:28:40 +01:00
Loic Poulain
ba8f359790 Bluetooth: hci_qca: Avoid setup failure on missing rampatch
Assuming that the original code idea was to enable in-band sleeping
only if the setup_rome method returns succes and run in 'standard'
mode otherwise, we should not return setup_rome return value which
makes qca_setup fail if no rampatch/nvm file found.

This fixes BT issue on the dragonboard-820C p4 which includes the
following QCA controller:
hci0: Product:0x00000008
hci0: Patch  :0x00000111
hci0: ROM    :0x00000302
hci0: SOC    :0x00000044

Since there is no rampatch for this controller revision, just make
it work as is.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-12-13 00:28:40 +01:00
Zhu Yanjun
c360f2b58e forcedeth: remove unnecessary structure member
Since both tx_ring and first_tx are the head of tx ring, it not
necessary to use two structure members to statically indicate
the head of tx ring. So first_tx is removed.

CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-11 14:03:56 -05:00
Carl Heymann
92a54f4a47 nfp: debug dump - decrease endian conversions
Convert the requested dump level parameter to big-endian at the start of
nfp_net_dump_calculate_size() and nfp_net_dump_populate_buffer(), then
compare and assign it directly where needed in the traversal and prolog
code. This decreases the total number of conversions used.

Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-11 12:08:13 -05:00
John Hurley
197171e5ba nfp: flower: remove unused defines
Delete match field defines that are not supported at this time.

Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-11 12:08:04 -05:00
John Hurley
a427673e1f nfp: flower: remove dead code paths
Port matching is selected by default on every rule so remove check for it
and delete 'else' side of the statement. Remove nfp_flower_meta_one as now
it will not feature in the code. Rename nfp_flower_meta_two given that one
has been removed.

'Additional metadata' if statement can never be true so remove it as well.

Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-11 12:07:57 -05:00
John Hurley
de7d954984 nfp: flower: do not assume mac/mpls matches
Remove the matching of mac/mpls as a default selection. These are not
necessarily set by a TC rule (unlike the port). Previously a mac/mpls
field would exist in every match and be masked out if not used. This patch
has no impact on functionality but removes unnessary memory assignment in
the match cmsg.

Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-11 12:07:47 -05:00
Mahesh Bandewar
92ff426450 ipvlan: add L2 check for packets arriving via virtual devices
Packets that don't have dest mac as the mac of the master device should
not be entertained by the IPvlan rx-handler. This is mostly true as the
packet path mostly takes care of that, except when the master device is
a virtual device. As demonstrated in the following case -

  ip netns add ns1
  ip link add ve1 type veth peer name ve2
  ip link add link ve2 name iv1 type ipvlan mode l2
  ip link set dev iv1 netns ns1
  ip link set ve1 up
  ip link set ve2 up
  ip -n ns1 link set iv1 up
  ip addr add 192.168.10.1/24 dev ve1
  ip -n ns1 addr 192.168.10.2/24 dev iv1
  ping -c2 192.168.10.2
  <Works!>
  ip neigh show dev ve1
  ip neigh show 192.168.10.2 lladdr <random> dev ve1
  ping -c2 192.168.10.2
  <Still works! Wrong!!>

This patch adds that missing check in the IPvlan rx-handler.

Reported-by: Amit Sikka <amit.sikka@ericsson.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-11 11:14:23 -05:00
Tom Herbert
97a6ec4ac0 rhashtable: Change rhashtable_walk_start to return void
Most callers of rhashtable_walk_start don't care about a resize event
which is indicated by a return value of -EAGAIN. So calls to
rhashtable_walk_start are wrapped wih code to ignore -EAGAIN. Something
like this is common:

       ret = rhashtable_walk_start(rhiter);
       if (ret && ret != -EAGAIN)
               goto out;

Since zero and -EAGAIN are the only possible return values from the
function this check is pointless. The condition never evaluates to true.

This patch changes rhashtable_walk_start to return void. This simplifies
code for the callers that ignore -EAGAIN. For the few cases where the
caller cares about the resize event, particularly where the table can be
walked in mulitple parts for netlink or seq file dump, the function
rhashtable_walk_start_check has been added that returns -EAGAIN on a
resize event.

Signed-off-by: Tom Herbert <tom@quantonium.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-11 09:58:38 -05:00
David S. Miller
51e18a453f Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflict was two parallel additions of include files to sch_generic.c,
no biggie.

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-09 22:09:55 -05:00
Linus Torvalds
e9ef1fe312 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:

 1) CAN fixes from Martin Kelly (cancel URBs properly in all the CAN usb
    drivers).

 2) Revert returning -EEXIST from __dev_alloc_name() as this propagates
    to userspace and broke some apps. From Johannes Berg.

 3) Fix conn memory leaks and crashes in TIPC, from Jon Malloc and Cong
    Wang.

 4) Gianfar MAC can't do EEE so don't advertise it by default, from
    Claudiu Manoil.

 5) Relax strict netlink attribute validation, but emit a warning. From
    David Ahern.

 6) Fix regression in checksum offload of thunderx driver, from Florian
    Westphal.

 7) Fix UAPI bpf issues on s390, from Hendrik Brueckner.

 8) New card support in iwlwifi, from Ihab Zhaika.

 9) BBR congestion control bug fixes from Neal Cardwell.

10) Fix port stats in nfp driver, from Pieter Jansen van Vuuren.

11) Fix leaks in qualcomm rmnet, from Subash Abhinov Kasiviswanathan.

12) Fix DMA API handling in sh_eth driver, from Thomas Petazzoni.

13) Fix spurious netpoll warnings in bnxt_en, from Calvin Owens.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
  net: mvpp2: fix the RSS table entry offset
  tcp: evaluate packet losses upon RTT change
  tcp: fix off-by-one bug in RACK
  tcp: always evaluate losses in RACK upon undo
  tcp: correctly test congestion state in RACK
  bnxt_en: Fix sources of spurious netpoll warnings
  tcp_bbr: reset long-term bandwidth sampling on loss recovery undo
  tcp_bbr: reset full pipe detection on loss recovery undo
  tcp_bbr: record "full bw reached" decision in new full_bw_reached bit
  sfc: pass valid pointers from efx_enqueue_unwind
  gianfar: Disable EEE autoneg by default
  tcp: invalidate rate samples during SACK reneging
  can: peak/pcie_fd: fix potential bug in restarting tx queue
  can: usb_8dev: cancel urb on -EPIPE and -EPROTO
  can: kvaser_usb: cancel urb on -EPIPE and -EPROTO
  can: esd_usb2: cancel urb on -EPIPE and -EPROTO
  can: ems_usb: cancel urb on -EPIPE and -EPROTO
  can: mcba_usb: cancel urb on -EPROTO
  usbnet: fix alignment for frames with no ethernet header
  tcp: use current time in tcp_rcv_space_adjust()
  ...
2017-12-08 13:32:44 -08:00
Linus Torvalds
77071bc6c4 media fixes for v4.15-rc3
-----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJaKrOpAAoJEAhfPr2O5OEVK5sP/iHWDJtRw/WWBYOqF9cGFl0o
 ssh1iXJAsOmLjaARMOkxQBPLwTvVMreux2fHow/mukrXB8BIR7OmflBaQRLM3lbW
 xm9G4yarXf7xgkxngisemQrJiweNyaNDX9P0BqJLV55Xhp+rO2Q6rutspho3xzoo
 Pmz7bgnt0FjBKz+0LWnKnzozdNinj2uhTdBOTgm9rUuUUGiAVTAQSNUq2e5Gzw3m
 DhO4UPOJDRmnZ6Rqldq2pD2wzmRfbVonirz7IEh7j2opcAoCM2TnmM+Z9C5zjlUj
 XVFagiR+XG8lsh2zvHdweter4X9DqLBlMbBDVAQ+vH+xhBuz63Yqq1pSIvXA342U
 rs1X182FSyE+pOxipuae94csHkyzlb9tmzoiUoItU+QXi8Wlg8pLH6GFQe/72t/g
 HpcXMBq2lflc2KDstx+QGs/G+1EYtz64vUXZ4pvuIitrhdbd5ulLh7Y7nb7qfEym
 WEHpaJwxh4MZh6RzB2tq+Tvy0/sD1krNjPTXtf2CuTdFNUuvk8QenRW1q2YVA06L
 UOTxRpfPYUPwhGKOoKb2IJ5g1xoztoqMaafdsUJ16H7fcuVtE9xQayVCVhaBuo08
 4g7SFCb7MhNLFG1Su291u9PKYlvGhCJaDPKE/6E+IM6szxt7h/kveYsdb05yWOoB
 di+cIWZkCRUzbO7fxz4J
 =xoHW
 -----END PGP SIGNATURE-----

Merge tag 'media/v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media

Pull media fixes from Mauro Carvalho Chehab:

 "A series of fixes for the media subsytem:

   - The largest amount of fixes in this series is with regards to
     comments that aren't kernel-doc, but start with "/**".

     A new check added for 4.15 makes it to produce a *huge* amount of
     new warnings (I'm compiling here with W=1). Most of the patches in
     this series fix those.

     No code changes - just comment changes at the source files

   - rc: some fixed in order to better handle RC repetition codes

   - v4l-async: use the v4l2_dev from the root notifier when matching
     sub-devices

   - v4l2-fwnode: Check subdev count after checking port

   - ov 13858 and et8ek8: compilation fix with randconfigs

   - usbtv: a trivial new USB ID addition

   - dibusb-common: don't do DMA on stack on firmware load

   - imx274: Fix error handling, add MAINTAINERS entry

   - sir_ir: detect presence of port"

* tag 'media/v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (50 commits)
  media: imx274: Fix error handling, add MAINTAINERS entry
  media: v4l: async: use the v4l2_dev from the root notifier when matching sub-devices
  media: v4l2-fwnode: Check subdev count after checking port
  media: et8ek8: select V4L2_FWNODE
  media: ov13858: Select V4L2_FWNODE
  media: rc: partial revert of "media: rc: per-protocol repeat period"
  media: dvb: i2c transfers over usb cannot be done from stack
  media: dvb-frontends: complete kernel-doc markups
  media: docs: add documentation for frontend attach info
  media: dvb_frontends: fix kernel-doc macros
  media: drivers: remove "/**" from non-kernel-doc comments
  media: lm3560: add a missing kernel-doc parameter
  media: rcar_jpu: fix two kernel-doc markups
  media: vsp1: add a missing kernel-doc parameter
  media: soc_camera: fix a kernel-doc markup
  media: mt2063: fix some kernel-doc warnings
  media: radio-wl1273: fix a parameter name at kernel-doc macro
  media: s3c-camif: add missing description at s3c_camif_find_format()
  media: mtk-vpu: add description for wdt fields at struct mtk_vpu
  media: vdec: fix some kernel-doc warnings
  ...
2017-12-08 13:18:47 -08:00
Linus Torvalds
4066aa72f9 i915, amdgpu + misc fixes
-----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJaKedrAAoJEAx081l5xIa+CLkP/AkLTMW17WT/aktLfq4/+NQV
 WGcLxQw+SB9iYMffFUNdQdMqv3pKsDzeatifxNuoRnjvK6rNZDUFK11SoTEFCdA+
 opI3zBPiyMVv71LtLF/r2kj3Vw5rnARdCg24FIzptGg/4j+G0EOb9uzd9qjmjof1
 r2XD1f0mjIG6SREMYCZPJj/Q/ZGfWFKXxcatmf87sAoq4o2nfoQ1Sl0T4cnMV7yp
 FzzFKA/j6OaiVa0Tb1KiJOl8VnW5f9STanUynFcPtKd2mhDcVaEP4lAfBhHgccd8
 ufmsyPJDadGQDT0iQY5E8n+ht124wg4gW8TKGqyxDfxuzTFj2k62WOUMH4eSjGSt
 x7SHEewTQLoV5kIPp0y00T2NWuA4/jmjjgllQZgqSFwnsv8fQ9/GwLNPWrUGM0+z
 6sqzj7QRyn8GGuYblqVghVYj0bX3ovmYlLzOaKZ+pNSM34hLBFRenZQ5mKJ6WrcE
 SIKzuQm3HEC8KwNw72zZ6+zz5fc7x9KuURztwEPt6vOMnxz1PtjWSdHzfvja4cH2
 6D2t0lZSqkM244FFG4ImFP6CDF+8vaY7i9YybjYteycWH7o9haVa869vCxUdNUWo
 DDghWKPRjbl7LJLJ14BxMrg0+sk+XWYcoZXjUAM0rYFFOWoFkVAlF8Sy3kgb5Pky
 wMLalQohWFbkZY60q02h
 =2f34
 -----END PGP SIGNATURE-----

Merge tag 'drm-fixes-for-v4.15-rc3' of git://people.freedesktop.org/~airlied/linux

Pull drm fixes from Dave Airlie:
 "This pull is a bit larger than I'd like but a large bunch of it is
  license fixes, AMD wanted to fix the licenses for a bunch of files
  that were missing them,

 Otherwise a bunch of TTM regression fix since the hugepage support,
 some i915 and gvt fixes, a core connector free in a safe context fix,
 and one bridge fix"

* tag 'drm-fixes-for-v4.15-rc3' of git://people.freedesktop.org/~airlied/linux: (26 commits)
  drm/bridge: analogix dp: Fix runtime PM state in get_modes() callback
  Revert "drm/i915: Display WA #1133 WaFbcSkipSegments:cnl, glk"
  drm/vc4: Fix false positive WARN() backtrace on refcount_inc() usage
  drm/i915: Call i915_gem_init_userptr() before taking struct_mutex
  drm/exynos: remove unnecessary function declaration
  drm/exynos: remove unnecessary descrptions
  drm/exynos: gem: Drop NONCONTIG flag for buffers allocated without IOMMU
  drm/exynos: Fix dma-buf import
  drm/ttm: swap consecutive allocated pooled pages v4
  drm: safely free connectors from connector_iter
  drm/i915/gvt: set max priority for gvt context
  drm/i915/gvt: Don't mark vgpu context as inactive when preempted
  drm/i915/gvt: Limit read hw reg to active vgpu
  drm/i915/gvt: Export intel_gvt_render_mmio_to_ring_id()
  drm/i915/gvt: Emulate PCI expansion ROM base address register
  drm/ttm: swap consecutive allocated cached pages v3
  drm/ttm: roundup the shrink request to prevent skip huge pool
  drm/ttm: add page order support in ttm_pages_put
  drm/ttm: add set_pages_wb for handling page order more than zero
  drm/ttm: add page order in page pool
  ...
2017-12-08 13:11:57 -08:00
Linus Torvalds
7267212c80 Merge tag 'md/4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md
Pull md fixes from Shaohua Li:
 "Some MD fixes.

  The notable one is a raid5-cache deadlock bug with dm-raid, others are
  not significant"

* tag 'md/4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  md/raid1/10: add missed blk plug
  md: limit mdstat resync progress to max_sectors
  md/r5cache: move mddev_lock() out of r5c_journal_mode_set()
  md/raid5: correct degraded calculation in raid5_error
2017-12-08 13:03:02 -08:00
Linus Torvalds
78d9b04844 DeviceTree fixes for v4.15 (part2):
- Fixes from overlay code rework. A trifecta of fixes to the locking,
   an out of bounds access, and a memory leak in of_overlay_apply().
 
 - Clean-up at25 eeprom binding document
 
 - Remove leading '0x' in unit-addresses from binding docs
 -----BEGIN PGP SIGNATURE-----
 
 iQItBAABCAAXBQJaKrC8EBxyb2JoQGtlcm5lbC5vcmcACgkQ+vtdtY28YcPY7Q/9
 GOZDOhajewVoYo+LkKl8+1wtdih7QHOvziKY8Jn1Nd/o6ASXU5ltOxvk5iF/q4tz
 x7JFKMkUo8eyOy5p5XnkqAzOnQ+rP+aRvHxjeAiMtQZRtMcDJ6bv4FRMI4/hq610
 QocAcxzblXJayy/Ad2sbuMr34O6QBkvnicMiLHZNb2IhCgk0nxBbyiNJDr868XE6
 CwlkKgo+y0fFJKkW3y4v4jaMdMlmcxTPTY+4jOJoGnnD1LgNwNRgkTFCzRQLebBk
 E5D6XweMS7G0IOO8wLYEn70JYsNk4wRGjIvlZGR1e5REQNgT9H+1J8rXLxlWc5rk
 l2o4V3+nrBj3BpVCG5oQWBrwVsMZS8ExdnRnrGmZJ25C1EFzlRHGYtsvo6fvXsLs
 T2VfYPEDhN5IHZiUU/rcHfz1VpHjuBrtFStPQkFTSTfO52n22Q5KWBxHUqUjXbBZ
 phcPoHcDm+FfO4swkLuIP0wDAiNj8SJpJJNnHLrgIuy52UvXe/VD5BlY5RgXIZbg
 XhxAcsNKrqfH8ggfbM7ndXkUoFrDyl/dOupfwbtwzNqDQiPGvpjkr9hmE7XIL2aJ
 tyGahgkpZ3n49oGJPe5rTHKJacZBkl6rNI2CFQfERXyGYUmQSEU6AViSSyRG6ljK
 kXLmIzNPgJJF/I9YC3q8Wr6FUoOAapE7Zww/Cc83xJ8=
 =vBBN
 -----END PGP SIGNATURE-----

Merge tag 'devicetree-fixes-for-4.15-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

Pull DeviceTree fixes from Rob Herring:
 "Another set of DT fixes:

   - Fixes from overlay code rework. A trifecta of fixes to the locking,
     an out of bounds access, and a memory leak in of_overlay_apply()

   - Clean-up at25 eeprom binding document

   - Remove leading '0x' in unit-addresses from binding docs"

* tag 'devicetree-fixes-for-4.15-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  of: overlay: Make node skipping in init_overlay_changeset() clearer
  of: overlay: Fix out-of-bounds write in init_overlay_changeset()
  of: overlay: Fix (un)locking in of_overlay_apply()
  of: overlay: Fix memory leak in of_overlay_apply() error path
  dt-bindings: eeprom: at25: Document device-specific compatible values
  dt-bindings: eeprom: at25: Grammar s/are can/can/
  dt-bindings: Remove leading 0x from bindings notation
  of: overlay: Remove else after goto
  of: Spelling s/changset/changeset/
  of: unittest: Remove bogus overlay mutex release from overlay_data_add()
2017-12-08 13:00:51 -08:00
Linus Torvalds
900add27f5 virtio: bugfixes
A couple of minor bugfixes.
 
 Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
 -----BEGIN PGP SIGNATURE-----
 
 iQEcBAABAgAGBQJaKW26AAoJECgfDbjSjVRpDwIH/1tq1vcjd5i00nh+gQD7jWm2
 qWrpcKbsS0ANTvhm9UNFY24BVoPuNpNrApQpuBxmgxE/XGqx7A+8xXhwPAM5lLiG
 uDSPB2nsfjvEUOde7bgeR+t6ay+Ki2UWKzY46lSoCTcIN7BSVFWQZonsGu2xLDzz
 kKpCtlobXRnXzeWm+fh1oOZu/cn/TuAF0mbb+6TUQqSsHAt6PQ3Hwsly2EmQV5xR
 of6Si/TnxFOkhZUKpezbuTU/g/20ZkHUSzgfrOuZLGonaIvZIE6BUm8m21/IgCbw
 WnwSqe66WsWF2vd0RDLFq4L3qaRyGn+W7iYo3KPbwIPEEotSRFMUgixBWBB3IgU=
 =Pf4w
 -----END PGP SIGNATURE-----

Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost

Pull virtio bugfixes from Michael Tsirkin:
 "A couple of minor bugfixes"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio_net: fix return value check in receive_mergeable()
  virtio_mmio: add cleanup for virtio_mmio_remove
  virtio_mmio: add cleanup for virtio_mmio_probe
2017-12-08 12:58:51 -08:00
Linus Torvalds
32abeb09ab xen: fixes for 4.15-rc3
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQEcBAABAgAGBQJaKlu/AAoJELDendYovxMvaqoH/i7gN9xry7QkUM6RkwddGwYY
 v0rqaUo4WCW27yFOE7Bzej9Y+W92/eFPJnVUhc/quTVfV+uEjbs4PiAwuxSr+lIU
 X+BhBNbEi9C5RlRL1z75J0ZySyu6WXL2hsmPbc0wrrqdQikfiZ7bnRjdGAHh5C5C
 TijKQKGZTt6ccjIPUEZTIqeajOt/p7uxkCXPWhHQA1mudf9PVhsKyYnGdYp5gp8X
 KID+8XmKtAcSwPUz+eG9vGlGwmP28mH0BfCT0suC2uUI4o+PJFPqBTlfsco2kfHO
 NqVCgnMZs31Js8mdEVz8h2ZO8m2T5m1oml1zOeyDbgTJ8yjqgADy8K6Lm38clko=
 =ZHtb
 -----END PGP SIGNATURE-----

Merge tag 'for-linus-4.15-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip

Pull xen fixes from Juergen Gross:
 "Just two small fixes for the new pvcalls frontend driver"

* tag 'for-linus-4.15-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/pvcalls: Fix a check in pvcalls_front_remove()
  xen/pvcalls: check for xenbus_read() errors
2017-12-08 12:53:43 -08:00
David S. Miller
fd29117aeb linux-can-fixes-for-4.15-20171208
-----BEGIN PGP SIGNATURE-----
 
 iQFHBAABCgAxFiEE4bay/IylYqM/npjQHv7KIOw4HPYFAloqeVYTHG1rbEBwZW5n
 dXRyb25peC5kZQAKCRAe/sog7Dgc9tiqCADK4f/QYW5q5jC93A6JZSItI8vAK2+h
 0s4MRTj9x+thBIGIhJ59uYBSTd374bvsWmrGdV7CBoGX4TnEJfGiMV77lpGnGRVG
 jpzk9cSFoAnE5UW2qZlF+JM8SNEFlU18MCQQlnMzKbSGerUAlveK+mcF5sJrqrQh
 CGZ9MH1Bp4Fz3WMRQ9hHzKWjTOhhM54qjPceCVTZM6I0RJam6I2lpVZPQeom9uVa
 r+F5Lv2ZOpNZc+8Pbu+L95YyivKKaQOPzeP4btFLNEHUyFDygHcv2iKRIn9MdEu2
 2XfaDVKk2Ey/qWc782SLBxLOihnhWltwC7Kg1ZnrLhNZ6V5UbYQ5FzF4
 =OMZE
 -----END PGP SIGNATURE-----

Merge tag 'linux-can-fixes-for-4.15-20171208' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2017-12-08

this is a pull request of 6 patches for net/master.

Martin Kelly provides 5 patches for various USB based CAN drivers, that
properly cancel the URBs on adapter unplug, so that the driver doesn't
end up in an endless loop. Stephane Grosjean provides a patch to restart
the tx queue if zero length packages are transmitted.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 14:53:54 -05:00
David S. Miller
03afb6e43a wireless-drivers fixes for 4.15
Second set of fixes for 4.15. This time a lot of iwlwifi patches and
 two brcmfmac patches. Most important here are the MIC and IVC fixes
 for iwlwifi to unbreak 9000 series.
 
 iwlwifi
 
 * fix rate-scaling to not start lowest possible rate
 
 * fix the TX queue hang detection for AP/GO modes
 
 * fix the TX queue hang timeout in monitor interfaces
 
 * fix packet injection
 
 * remove a wrong error message when dumping PCI registers
 
 * fix race condition with RF-kill
 
 * tell mac80211 when the MIC has been stripped (9000 series)
 
 * tell mac80211 when the IVC has been stripped (9000 series)
 
 * add 2 new PCI IDs, one for 9000 and one for 22000
 
 * fix a queue hang due during a P2P Remain-on-Channel operation
 
 brcmfmac
 
 * fix a race which sometimes caused a crash during sdio unbind
 
 * fix a kernel-doc related build error
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJaKp9UAAoJEG4XJFUm622bhXgH+wTtTVEH0lAOTtK+PyBkxkRH
 Q+55Yf1XZ9lNYxmfXhYgObusSbmeL8tClMuISCcQS9gX0um1Vuuud4CLemgO2V7R
 V1xuWTKjanaKf8PouKx9SUt1Fx6CsFdwlivJX+eZTfKlKYtwNbNX4onWl9GN2jVZ
 5/2l+m3MJbTMMzarZTGLkBJqpTk8DGTNINtKeRd+VF+717SlbqpRlw1TTlbVJcR2
 nHcJ3p5JGbU/+hOTroOWUr7kGdpdYlWLfcyOL8iT3rZXtAzH/POjPAmQv9VVRaC+
 anm5zn+gZ5GH9XF+pc3nrGOEZ2Ei4LtszMQjdo4Zo9V3ngCj/0OoEnkto6VLbkw=
 =lzG8
 -----END PGP SIGNATURE-----

Merge tag 'wireless-drivers-for-davem-2017-12-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.15

Second set of fixes for 4.15. This time a lot of iwlwifi patches and
two brcmfmac patches. Most important here are the MIC and IVC fixes
for iwlwifi to unbreak 9000 series.

iwlwifi

* fix rate-scaling to not start lowest possible rate

* fix the TX queue hang detection for AP/GO modes

* fix the TX queue hang timeout in monitor interfaces

* fix packet injection

* remove a wrong error message when dumping PCI registers

* fix race condition with RF-kill

* tell mac80211 when the MIC has been stripped (9000 series)

* tell mac80211 when the IVC has been stripped (9000 series)

* add 2 new PCI IDs, one for 9000 and one for 22000

* fix a queue hang due during a P2P Remain-on-Channel operation

brcmfmac

* fix a race which sometimes caused a crash during sdio unbind

* fix a kernel-doc related build error
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 14:48:49 -05:00
Marc Kleine-Budde
936e5d8bdf slip: sl_alloc(): remove unused parameter "dev_t line"
The first and only parameter of sl_alloc() is unused, so remove it.

Fixes: 5342b77c41 slip: ("Clean up create and destroy")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 14:41:02 -05:00
Antoine Tenart
8a7b741e76 net: mvpp2: fix the RSS table entry offset
The macro used to access or set an RSS table entry was using an offset
of 8, while it should use an offset of 0. This lead to wrongly configure
the RSS table, not accessing the right entries.

Fixes: 1d7d15d79f ("net: mvpp2: initialize the RSS tables")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 14:35:15 -05:00
Rahul Lakkireddy
6078ab196b cxgb4: collect PCIe configuration logs
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 14:31:50 -05:00
Rahul Lakkireddy
736c3b9447 cxgb4: collect egress and ingress SGE queue contexts
Use meminfo to identify the egress and ingress context regions and
fetch all valid contexts from those regions. Also flush all contexts
before attempting collection to prevent stale information.

Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 14:31:50 -05:00
Rahul Lakkireddy
c1219653f3 cxgb4: skip TX and RX payload regions in memory dumps
Use meminfo to identify TX and RX payload regions and skip them in
collection of EDC, MC, and HMA.

Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 14:31:50 -05:00
Rahul Lakkireddy
4db0401f8a cxgb4: collect HMA memory dump
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 14:31:50 -05:00
Rahul Lakkireddy
a1c69520f7 cxgb4: collect MC memory dump
Use meminfo to get base address and size of MC memory.  Also use same
meminfo for EDC memory dumps.

Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 14:31:50 -05:00
Rahul Lakkireddy
123e25c4a5 cxgb4: collect on-chip memory information
Collect memory layout of various on-chip memory regions.  Move code
for collecting on-chip memory information to cudbg_lib.c and update
cxgb4_debugfs.c to use the common function.  Also include
cudbg_entity.h before cudbg_lib.h to avoid adding cudbg entity
structure forward declarations in cudbg_lib.h.

Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 14:31:49 -05:00
Stephen Hemminger
72d24955b4 veth: set peer GSO values
When new veth is created, and GSO values have been configured
on one device, clone those values to the peer.

For example:
   # ip link add dev vm1 gso_max_size 65530 type veth peer name vm2

This should create vm1 <--> vm2 with both having GSO maximum
size set to 65530.

Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 14:22:59 -05:00
Niklas Cassel
5a6a0445d1 net: stmmac: fix broken dma_interrupt handling for multi-queues
There is nothing that says that number of TX queues == number of RX
queues. E.g. the ARTPEC-6 SoC has 2 TX queues and 1 RX queue.

This code is obviously wrong:
for (chan = 0; chan < tx_channel_count; chan++) {
    struct stmmac_rx_queue *rx_q = &priv->rx_queue[chan];

priv->rx_queue has size MTL_MAX_RX_QUEUES, so this will send an
uninitialized napi_struct to __napi_schedule(), causing us to
crash in net_rx_action(), because napi_struct->poll is zero.

[12846.759880] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[12846.768014] pgd = (ptrval)
[12846.770742] [00000000] *pgd=39ec7831, *pte=00000000, *ppte=00000000
[12846.777023] Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM
[12846.782942] Modules linked in:
[12846.785998] CPU: 0 PID: 161 Comm: dropbear Not tainted 4.15.0-rc2-00285-gf5fb5f2f39a7 #36
[12846.794177] Hardware name: Axis ARTPEC-6 Platform
[12846.798879] task: (ptrval) task.stack: (ptrval)
[12846.803407] PC is at 0x0
[12846.805942] LR is at net_rx_action+0x274/0x43c
[12846.810383] pc : [<00000000>]    lr : [<80bff064>]    psr: 200e0113
[12846.816648] sp : b90d9ae8  ip : b90d9ae8  fp : b90d9b44
[12846.821871] r10: 00000008  r9 : 0013250e  r8 : 00000100
[12846.827094] r7 : 0000012c  r6 : 00000000  r5 : 00000001  r4 : bac84900
[12846.833619] r3 : 00000000  r2 : b90d9b08  r1 : 00000000  r0 : bac84900

Since each DMA channel can be used for rx and tx simultaneously,
the current code should probably be rewritten so that napi_struct is
embedded in a new struct stmmac_channel.
That way, stmmac_poll() can call stmmac_tx_clean() on just the tx queue
where we got the IRQ, instead of looping through all tx queues.
This is also how the xgbe driver does it (another driver for this IP).

Fixes: c22a3f48ef ("net: stmmac: adding multiple napi mechanism")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 14:18:40 -05:00
Egil Hjelmeland
2e8d243e88 net: dsa: lan9303: Protect ALR operations with mutex
ALR table operations are a sequence of related register operations which
should be protected from concurrent access. The alr_cache should also be
protected. Add alr_mutex doing that.

Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 14:12:33 -05:00
Calvin Owens
2edbdb3159 bnxt_en: Fix sources of spurious netpoll warnings
After applying 2270bc5da3 ("bnxt_en: Fix netpoll handling") and
903649e718 ("bnxt_en: Improve -ENOMEM logic in NAPI poll loop."),
we still see the following WARN fire:

  ------------[ cut here ]------------
  WARNING: CPU: 0 PID: 1875170 at net/core/netpoll.c:165 netpoll_poll_dev+0x15a/0x160
  bnxt_poll+0x0/0xd0 exceeded budget in poll
  <snip>
  Call Trace:
   [<ffffffff814be5cd>] dump_stack+0x4d/0x70
   [<ffffffff8107e013>] __warn+0xd3/0xf0
   [<ffffffff8107e07f>] warn_slowpath_fmt+0x4f/0x60
   [<ffffffff8179519a>] netpoll_poll_dev+0x15a/0x160
   [<ffffffff81795f38>] netpoll_send_skb_on_dev+0x168/0x250
   [<ffffffff817962fc>] netpoll_send_udp+0x2dc/0x440
   [<ffffffff815fa9be>] write_ext_msg+0x20e/0x250
   [<ffffffff810c8125>] call_console_drivers.constprop.23+0xa5/0x110
   [<ffffffff810c9549>] console_unlock+0x339/0x5b0
   [<ffffffff810c9a88>] vprintk_emit+0x2c8/0x450
   [<ffffffff810c9d5f>] vprintk_default+0x1f/0x30
   [<ffffffff81173df5>] printk+0x48/0x50
   [<ffffffffa0197713>] edac_raw_mc_handle_error+0x563/0x5c0 [edac_core]
   [<ffffffffa0197b9b>] edac_mc_handle_error+0x42b/0x6e0 [edac_core]
   [<ffffffffa01c3a60>] sbridge_mce_output_error+0x410/0x10d0 [sb_edac]
   [<ffffffffa01c47cc>] sbridge_check_error+0xac/0x130 [sb_edac]
   [<ffffffffa0197f3c>] edac_mc_workq_function+0x3c/0x90 [edac_core]
   [<ffffffff81095f8b>] process_one_work+0x19b/0x480
   [<ffffffff810967ca>] worker_thread+0x6a/0x520
   [<ffffffff8109c7c4>] kthread+0xe4/0x100
   [<ffffffff81884c52>] ret_from_fork+0x22/0x40

This happens because we increment rx_pkts on -ENOMEM and -EIO, resulting
in rx_pkts > 0. Fix this by only bumping rx_pkts if we were actually
given a non-zero budget.

Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 14:07:19 -05:00
Bert Kenward
d4a7a8893d sfc: pass valid pointers from efx_enqueue_unwind
The bytes_compl and pkts_compl pointers passed to efx_dequeue_buffers
cannot be NULL. Add a paranoid warning to check this condition and fix
the one case where they were NULL.

efx_enqueue_unwind() is called very rarely, during error handling.
Without this fix it would fail with a NULL pointer dereference in
efx_dequeue_buffer, with efx_enqueue_skb in the call stack.

Fixes: e9117e5099 ("sfc: Firmware-Assisted TSO version 2")
Reported-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 13:25:39 -05:00
Claudiu Manoil
b6b5e8a691 gianfar: Disable EEE autoneg by default
This controller does not support EEE, but it may connect to a PHY
which supports EEE and advertises EEE by default, while its link
partner also advertises EEE. If this happens, the PHY enters low
power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
gianfar connects to, to prevent the above unwanted outcome.

Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Tested-by: Yangbo Lu <Yangbo.lu@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 13:23:01 -05:00
Toshiaki Makita
fdaa767aef virtio_net: Disable interrupts if napi_complete_done rescheduled napi
Since commit 39e6c8208d ("net: solve a NAPI race") napi has been able
to be rescheduled within napi_complete_done() even in non-busypoll case,
but virtnet_poll() always enabled interrupts before complete, and when
napi was rescheduled within napi_complete_done() it did not disable
interrupts.
This caused more interrupts when event idx is disabled.

According to commit cbdadbbf0c ("virtio_net: fix race in RX VQ
processing") we cannot place virtqueue_enable_cb_prepare() after
NAPI_STATE_SCHED is cleared, so disable interrupts again if
napi_complete_done() returned false.

Tested with vhost-user of OVS 2.7 on host, which does not have the event
idx feature.

* Before patch:

$ netperf -t UDP_STREAM -H 192.168.150.253 -l 60 -- -m 1472
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.150.253 () port 0 AF_INET
Socket  Message  Elapsed      Messages
Size    Size     Time         Okay Errors   Throughput
bytes   bytes    secs            #      #   10^6bits/sec

212992    1472   60.00     32763206      0    6430.32
212992           60.00     23384299           4589.56

Interrupts on guest: 9872369
Packets/interrupt:   2.37

* After patch

$ netperf -t UDP_STREAM -H 192.168.150.253 -l 60 -- -m 1472
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.150.253 () port 0 AF_INET
Socket  Message  Elapsed      Messages
Size    Size     Time         Okay Errors   Throughput
bytes   bytes    secs            #      #   10^6bits/sec

212992    1472   60.00     32794646      0    6436.49
212992           60.00     32793501           6436.27

Interrupts on guest: 4941299
Packets/interrupt:   6.64

Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 13:18:40 -05:00
Linus Torvalds
c6b3e9693f Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:

 - three more patches in regard to the SPDX license tags. The missing
   tags for the files in arch/s390/kvm will be merged via the KVM tree.
   With that all s390 related files should have their SPDX tags.

 - a patch to get rid of 'struct timespec' in the DASD driver.

 - bug fixes

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390: fix compat system call table
  s390/mm: fix off-by-one bug in 5-level page table handling
  s390: Remove redudant license text
  s390: add a few more SPDX identifiers
  s390/dasd: prevent prefix I/O error
  s390: always save and restore all registers on context switch
  s390/dasd: remove 'struct timespec' usage
  s390/qdio: restrict target-full handling to IQDIO
  s390/qdio: consider ERROR buffers for inbound-full condition
  s390/virtio: add BSD license to virtio-ccw
2017-12-08 10:10:17 -08:00
Linus Torvalds
3625de4b28 ACPI fix for v4.15-rc3
This fixes an out of bounds warning from KASAN in the ACPI
 CPPC driver.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJaKXLtAAoJEILEb/54YlRxEmUQAJ1MnvVoCIpB/NC/gcp8wBwZ
 Y9rOJhnsgTiAA8Or7YJCOhPAHCa2S16m/nCkgrZfSjNgYJ/nHT8SB5vw8Fkc/PIz
 Jmc3E/yVvn446c9ozSa3NALth5Ov90ys4HFsF3jjetTr7aDwmwjaC2pIGRBd6pUK
 nk1MBMdu4wsGYssCV3dMjH4B1TmnU3rLyCl95yFFI8jgjA4slVk+I3EtxrlSOOHy
 9wnbHOWch2UbJBDQLIhhgXKcUXDxnwfBJ8aoEGQ2LokTU1pdXMJG2RFPKG1Dtuqh
 JBhSRXe7jA7jkdGda6sXFOWc7hXMscf0FMOvf3+x7q91OIumtNqxIm45nTEdMOBl
 vT5eFsAUOD8HzaA9BYt/QVIFR9jG0leofVpgK+xGVzISWrLSavaEcuX1gblJ120I
 iJMd0zuPnrktjYRn6VWxVKXpGKr4/EqCuVRE3EHG9aERJtKsfN9vIh66m97JfI2D
 Eb8ifaL7nVIALoWPlq53Lhjllf/cCwvoUNMLhnnoqZU5HWOfolTyGQHeI0DjhQv2
 UCxjuKFCtBKQyMNNyWXF1MWOGcgky3v/4HdkYjfly1h0eO6l5owilj+OW4cxss9l
 NtUCuT2IsQ6dO5oooz+fHzvz0AkgtB+pYLZie28+b3Y5CgvnKTYsnxeMVchkcmo1
 XnL6KGvGgX68z/0AVrMt
 =35fs
 -----END PGP SIGNATURE-----

Merge tag 'acpi-4.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull ACPI fix from Rafael Wysocki:
 "This fixes an out of bounds warning from KASAN in the ACPI CPPC
  driver"

* tag 'acpi-4.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / CPPC: Fix KASAN global out of bounds warning
2017-12-08 10:05:53 -08:00
Linus Torvalds
7ed9fd2e29 Power management fix for v4.15-rc3
This fixes an issue in the device runtime PM framework that prevents
 customer devices from resuming if runtime PM is disabled for one or
 more of their supplier devices (as reflected by device links between
 those devices).
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIbBAABCAAGBQJaKXG3AAoJEILEb/54YlRxBjQP90QAzPd1hg8bTmn9OQc3aB1q
 IRR6AZDx/ZQ4ORn1P5IVcjxB9hrnsRbfOi1saeiFrkNZfdr7i0X+ViF/4hjcQfuK
 mc//rKxGhUCqlT9mX4i0wY7quxglZWjFh3ld+qlQNNCip0D4JZEo8mYF4BFbjkg4
 s3940XvXxgx1RRB5b1PsfWrlnAc/LgE4o4+1HvVVPKQdZZPsDHWJkDGuhI4in+fS
 lIoiAzx8dkh6O1JRAQQoaurygtfCd4/ni552DhaiKPxXmoLK5dKl1RJqku2PxMk9
 4GdU2k/JFyQZOx1EMWWiINjqivUBq+dIbK2wo4kike5mAh7v71/PT5lIC2mNG8td
 xd/o9zFG8qZ9USZHFKQmQk7kftCebipYlEZkJiUueUQa3uXDt6BGUhZ/YUoEL/dv
 Svy3fx4iCz3eX98aoJIL9ng0O98BJdV0m9cxBm10qXVlBnsrP1gBp43OaNoxNUDz
 duh4/kJJ3EC0lnYdIOyP3Wl1pzQKO8ZLBr5iA+3Fnm6XWfx2/nKaUijIFu73oHJq
 0ZJaApH52yh00uL4Rwy0CKx2cZi67G7HVMoiZ/DpZFA6XEKrnfvBb/tHrZ/Z61rC
 BLSdBDgZZ2ZyitZgHrttKJV5cBgC8EIcewTGYDwU+s17KgtWsXermktYYWXigBFq
 fgcz+26Gzrv8mnpWk+M=
 =/T0U
 -----END PGP SIGNATURE-----

Merge tag 'pm-4.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull power management fix from Rafael Wysocki:
 "This fixes an issue in the device runtime PM framework that prevents
  customer devices from resuming if runtime PM is disabled for one or
  more of their supplier devices (as reflected by device links between
  those devices)"

* tag 'pm-4.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM / runtime: Fix handling of suppliers with disabled runtime PM
2017-12-08 09:58:10 -08:00
Jason Wang
124da8f611 tuntap: fix possible deadlock when fail to register netdev
Private destructor could be called when register_netdev() fail with
rtnl lock held. This will lead deadlock in tun_free_netdev() who tries
to hold rtnl_lock. Fixing this by switching to use spinlock to
synchronize.

Fixes: 96f8406162 ("tun: add eBPF based queue selection method")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 10:44:27 -05:00
Geert Uytterhoeven
589b754df3 of: overlay: Make node skipping in init_overlay_changeset() clearer
Make it more clear that nodes without "__overlay__" subnodes are
skipped, by reverting the logic and using continue.
This also reduces indentation level.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
2017-12-08 09:32:18 -06:00