Apalis/Colibri iMX6 V1.2 replaced the STMPE811 ADC/touch controller,
which is EOL, with the TLA2024 ADC and AD7879 touch controller.
Accurately describe the new hardware.
v1.1 of these SoMs is still described by the following DTSI files:
imx6qdl-apalis.dtsi
imx6qdl-colibri.dtsi
v1.2 is now supported by a DTSI that modifies v1.1:
imx6qdl-apalis-v1.2.dtsi
imx6qdl-colibri-v1.2.dtsi
For each carrier board using these modules, a new DTS file was added
that includes the v1.1 DTS and modifies it with this v1.2 DTSI.
The original DTS can be used for modules up to and including v1.1.
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the STMPE811 touchscreen in the SOM dtsi files. The STMPE811 is
part of the SOM. It's self contained within it, therefore, disabling it
is not the correct default behavior.
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the Variscite Concerto Carrier Board with:
- LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch
display (not configured)
- USB Host + USB OTG Connector
- 10/100 Mbps Ethernet
- miniPCI-Express slot
- SD Card connector
- Audio Headphone/Line In jack connectors
- S-ATA
- On-board DMIC
Product Page: https://www.variscite.com/product/single-board-computers/concerto-board
This file is based on the one provided by Variscite on their own kernel,
but adapted for mainline.
Signed-off-by: Antonin Godard <antonin.godard@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the Variscite VAR_SOM-MX6UL SoM with:
- NXP i.MX6 UltraLite SoC
- 128–1024 MB DDR3L
- 8–128 GB eMMC
- 128–512 MB SLC NAND
- Camera Interface
- LVDS / Parallel RGB interfaces (not configured)
- Touch controller (not configured)
- Ethernet RMII interface (not configured)
- On-SoM Wi-Fi/Bluetooth with CYW43353 on SDIO Module (not configured)
- SD/MMC/SDIO interface
- USB Host + USB OTG interface
- I2C interfaces
- SPI interfaces
- PCI-Express 2.0 interface
- on-SoM Audio Codec (not configured)
- S/PDIF interface (not configured)
Product website: https://www.variscite.com/product/system-on-module-som/cortex-a7/var-som-6ul-nxp-imx6ul-6ull-6ulz
Support is handled with a SoM-centric dtsi exporting the default
interfaces along the default pinmuxing to be enabled by the board dts
file.
I tested this on a VAR-SOM-6UL_G2_700C_512R_8N_IT_REV1.3A, which is why
some of the features above are mentioned as "not configured" (I couldn't
test them).
This file is based on the one provided by Variscite on their own kernel,
but adapted for mainline.
Signed-off-by: Antonin Godard <antonin.godard@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SoM cannot be used standalone, this compatible is invalid and it is
always overwritten when this .dtsi file is included, remove it
therefore.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SoM cannot be used standalone, this compatible is invalid and it is
always overwritten when this .dtsi file is included, remove it
therefore.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
TQMa6UL1 has only one FEC which needs to be disabled as one of the last
steps.
imx6ul-tqma6ul2.dtsi can't be included in imx6ul-tqma6ul1.dtsi as the
defaults from imx6ul.dtsi will be applied again.
Fixes: 7b8861d8e6 ("ARM: dts: imx6ul: add TQ-Systems MBa6ULx device trees")
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
gpio-pca95xx.yaml documents 'nxp,pca9554', so use this compatible
to fix the following dt-schema warning:
failed to match any schema with compatible: ['pca9554']
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to mxc-nand.yaml, the correct node name must be
'nand-controller'.
Change it accordingly to fix the following dt-schema warning:
$nodename:0: 'nand@b8000000' does not match '^nand-controller(@.*)?'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to fsl,dspi.yaml the expected order for describing the dmas
and dma-names properties is "tx" first, followed by "rx".
Adjust it acordingly to fix the following dt-schema warnings:
spi@4002c000: dma-names:0: 'tx' was expected
spi@4002c000: dma-names:1: 'rx' was expected
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The bootloader adds MTD partitions in this subnode if present.
Add an empty partitions node which the bootloader will fill with
configured MTD partitions.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(Q)SPI NOR flash is supplied by 3.3V. Add the corresponding supply.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The bootloader adds MTD partitions in this subnode if present, or in the
spi-nor node itself otherwise.
Setting #size-cells in MTD nodes itself is deprecated by mtd.yaml.
Fix all this by adding an empty partitions node which the bootloader will
fill with configured MTD partitions. Remove the deprecated properties
as well.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(Q)SPI NOR flash is supplied by 1.8V. Add the corresponding supply.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The bootloader may add MTD partitions in this subnode if present.
Add an empty partitions node which the bootloader will fill with
configured MTD partitions. Remove #size-cells from MTD node
because this is deprecated.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This matches the real hardware and allows to remove
the virtual 3.3V regulator.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is a fixed 3.3V rail supplying several hardware on SOM.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
WM8960 has the following power supplies:
- AVDD
- DBVDD
- DCVDD
- SPKVDD1
- SPKVDD2
Add new audio regulators to reflect the schematic and complete missed
power supplies.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
WM8960 has the following power supplies:
- AVDD
- DBVDD
- DCVDD
- SPKVDD1
- SPKVDD2
Add new audio regulators to reflect the schematic and complete missed
power supplies.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to leds-gpio.yaml, the LED nodes should not contain
unit addresses. Remove them.
Also, 'default-trigger' is not a valid property. Change it to
'linux,default-trigger'.
These changes fix the following dt-schema warnings:
led@1: Unevaluated properties are not allowed ('reg' was unexpected)
led@2: Unevaluated properties are not allowed ('reg' was unexpected)
led@3: Unevaluated properties are not allowed ('default-trigger', 'reg' were unexpected)
leds: '#address-cells', '#size-cells' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently, the compatible string used for the spidev device is "lwn,bk4",
which is the same as the board compatible string documented at fsl.yaml.
This causes several dt-schema warnings:
make dtbs_check DT_SCHEMA_FILES=fsl.yaml
...
['lwn,bk4'] is too short
'lwn,bk4' is not one of ['tq,imx8dxp-tqma8xdp-mba8xx']
'lwn,bk4' is not one of ['tq,imx8qxp-tqma8xqp-mba8xx']
'lwn,bk4' is not one of ['armadeus,imx1-apf9328', 'fsl,imx1ads']
Use a more specific "lwn,bk4-spi" compatible string to fix the problem.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The card name for ALSA is generated from the model name string and
is limited to 16 characters. Use a shorter name to prevent cutting the
name.
Since nearly all starter kit mainboards for i.MX based SoM by TQ-Systems
use the same codec with the same routing on board it is a good idea to
use the same mode name for the sound card. This allows sharing a default
asound.conf in BSP over all the kits.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The card name for ALSA is generated from the model name string and
is limited to 16 characters. Use a shorter name to prevent cutting the
name.
Since nearly all starter kit mainboards for i.MX based SoM by TQ-Systems
use the same codec with the same routing on board it is a good idea to
use the same mode name for the sound card. This allows sharing a default
asound.conf in BSP over all the kits.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The card name for ALSA is generated from the model name string and
is limited to 16 characters. Use a shorter name to prevent cutting the
name.
Since nearly all starter kit mainboards for i.MX based SoM by TQ-Systems
use the same codec with the same routing on board it is a good idea to
use the same mode name for the sound card. This allows sharing a default
asound.conf in BSP over all the kits.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Bindings expect GPIO hog names to end with 'hog' suffix, so correct it
to fix dtbs_check warning:
vf610-zii-dev-rev-c.dtb: eth0_intrp: $nodename:0: 'eth0_intrp' does not match '^.+-hog(-[0-9]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On the i.MX5 chips the peripheral interrupts are represented directly only
by their interrupt numbers.
The CCM nodes are not following this format and cause the following
dt-schema warnings:
ccm@73fd4000: interrupts: [[0], [71], [4], [0], [72], [4]] is too long
Fix it by passing only the two interrupt numbers.
Run-time tested in on an imx53-qsb board.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to fsl,sec-v4.0.yaml, the job ring node names
should be 'jr'.
Change them to fix the following dt-schema warnings:
crypto@400f0000: 'jr0@1000', 'jr1@2000' do not match any of the regexes:
'^jr@[0-9a-f]+$', '^rtic@[0-9a-f]+$', 'pinctrl-[0-9]+'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to atmel,maxtouch.yaml, the correct property that describes
the GPIO connected to the touchscreen reset line is 'reset-gpios'.
Change it accordingly to fix the following dt-schema warning:
'reset-gpio' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
fsl,imx-iomuxc-gpr.yaml only contains the mux-controller but the actual
video-mux is not part of it. So move it below root node.
Fixes the dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx7s-mba7.dtb: iomuxc-gpr@30340000: 'csi-mux' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/soc/imx/fsl,imx-iomuxc-gpr.yaml#
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The btt3 device' HW revisions from 0 to 2 use imx287 SoC and are to
some extend similar to already upstreamed XEA devices, hence are
using common imx28-lwe.dtsi file.
New, imx28-btt3.dtsi has been added to embrace common DTS
properties for different HW revisions for this device.
As a result - changes introduced in imx28-btt3-[012].dts are
minimal.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- sh: boards: Use imply to enable hardware with complex dependencies
- sh: Migrate to the generic rule for built-in DTB
- sh: irq: Use seq_put_decimal_ull_width() for decimal values
-----BEGIN PGP SIGNATURE-----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=G6GL
-----END PGP SIGNATURE-----
Merge tag 'sh-for-v6.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from John Paul Adrian Glaubitz:
"Fixes and improvements for sh:
- replace seq_printf() with the more efficient
seq_put_decimal_ull_width() to increase performance when stress
reading /proc/interrupts (David Wang)
- migrate sh to the generic rule for built-in DTB to help avoid race
conditions during parallel builds which can occur because Kbuild
decends into arch/*/boot/dts twice (Masahiro Yamada)
- replace select with imply in the board Kconfig for enabling
hardware with complex dependencies. This addresses warnings which
were reported by the kernel test robot (Geert Uytterhoeven)"
* tag 'sh-for-v6.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: boards: Use imply to enable hardware with complex dependencies
sh: Migrate to the generic rule for built-in DTB
sh: irq: Use seq_put_decimal_ull_width() for decimal values
13 are for MM and 8 are for non-MM. All are singletons, please see the
changelogs for details.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZ54MEgAKCRDdBJ7gKXxA
jlhdAP0evTQ9JX+22DDWSVdWFBbnQ74c5ddFXVQc1LO2G2FhFgD+OXhH8E65Nez5
qGWjb4xgjoQTHS7AL4pYEFYqx/cpbAQ=
=rN+l
-----END PGP SIGNATURE-----
Merge tag 'mm-hotfixes-stable-2025-02-01-03-56' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"21 hotfixes. 8 are cc:stable and the remainder address post-6.13
issues. 13 are for MM and 8 are for non-MM.
All are singletons, please see the changelogs for details"
* tag 'mm-hotfixes-stable-2025-02-01-03-56' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (21 commits)
MAINTAINERS: include linux-mm for xarray maintenance
revert "xarray: port tests to kunit"
MAINTAINERS: add lib/test_xarray.c
mailmap, MAINTAINERS, docs: update Carlos's email address
mm/hugetlb: fix hugepage allocation for interleaved memory nodes
mm: gup: fix infinite loop within __get_longterm_locked
mm, swap: fix reclaim offset calculation error during allocation
.mailmap: update email address for Christopher Obbard
kfence: skip __GFP_THISNODE allocations on NUMA systems
nilfs2: fix possible int overflows in nilfs_fiemap()
mm: compaction: use the proper flag to determine watermarks
kernel: be more careful about dup_mmap() failures and uprobe registering
mm/fake-numa: handle cases with no SRAT info
mm: kmemleak: fix upper boundary check for physical address objects
mailmap: add an entry for Hamza Mahfooz
MAINTAINERS: mailmap: update Yosry Ahmed's email address
scripts/gdb: fix aarch64 userspace detection in get_current_task
mm/vmscan: accumulate nr_demoted for accurate demotion statistics
ocfs2: fix incorrect CPU endianness conversion causing mount failure
mm/zsmalloc: add __maybe_unused attribute for is_first_zpdesc()
...
Revert c7bb5cf9fc ("xarray: port tests to kunit"). It broke the build
when compiing the xarray userspace test harness code.
Reported-by: Sidhartha Kumar <sidhartha.kumar@oracle.com>
Closes: https://lkml.kernel.org/r/07cf896e-adf8-414f-a629-a808fc26014a@oracle.com
Cc: David Gow <davidgow@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Tamir Duberstein <tamird@gmail.com>
Cc: "Liam R. Howlett" <Liam.Howlett@oracle.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
If CONFIG_I2C=n:
WARNING: unmet direct dependencies detected for SND_SOC_AK4642
Depends on [n]: SOUND [=y] && SND [=y] && SND_SOC [=y] && I2C [=n]
Selected by [y]:
- SH_7724_SOLUTION_ENGINE [=y] && CPU_SUBTYPE_SH7724 [=y] && SND_SIMPLE_CARD [=y]
WARNING: unmet direct dependencies detected for SND_SOC_DA7210
Depends on [n]: SOUND [=y] && SND [=y] && SND_SOC [=y] && SND_SOC_I2C_AND_SPI [=n]
Selected by [y]:
- SH_ECOVEC [=y] && CPU_SUBTYPE_SH7724 [=y] && SND_SIMPLE_CARD [=y]
Fix this by replacing select by imply, instead of adding a dependency on
I2C.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501240836.OvXqmANX-lkp@intel.com/
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Commit 654102df2a ("kbuild: add generic support for built-in
boot DTBs") introduced generic support for built-in DTBs.
Select GENERIC_BUILTIN_DTB when built-in DTB support is enabled.
To keep consistency across architectures, this commit also renames
CONFIG_USE_BUILTIN_DTB to CONFIG_BUILTIN_DTB, and
CONFIG_BUILTIN_DTB_SOURCE to CONFIG_BUILTIN_DTB_NAME.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
On a system with n CPUs and m interrupts, there will be n*m decimal
values yielded via seq_printf(.."%10u "..) which has significant costs
parsing format string and is less efficient than seq_put_decimal_ull_width().
Stress reading /proc/interrupts indicates ~30% performance improvement with
this patch.
Signed-off-by: David Wang <00107082@163.com>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
* The PH1520 pinctrl and dwmac drivers are enabeled in defconfig.
* A redundant AQRL barrier has been removed from the futex cmpxchg
implementation.
* Support for the T-Head vector extensions, which includes exposing
these extensions to userspace on systems that implement them.
* Some more page table information is now printed on die() and systems
that cause PA overflows.
-----BEGIN PGP SIGNATURE-----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=HbAQ
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.14-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- The PH1520 pinctrl and dwmac drivers are enabeled in defconfig
- A redundant AQRL barrier has been removed from the futex cmpxchg
implementation
- Support for the T-Head vector extensions, which includes exposing
these extensions to userspace on systems that implement them
- Some more page table information is now printed on die() and systems
that cause PA overflows
* tag 'riscv-for-linus-6.14-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: add a warning when physical memory address overflows
riscv/mm/fault: add show_pte() before die()
riscv: Add ghostwrite vulnerability
selftests: riscv: Support xtheadvector in vector tests
selftests: riscv: Fix vector tests
riscv: hwprobe: Document thead vendor extensions and xtheadvector extension
riscv: hwprobe: Add thead vendor extension probing
riscv: vector: Support xtheadvector save/restore
riscv: Add xtheadvector instruction definitions
riscv: csr: Add CSR encodings for CSR_VXRM/CSR_VXSAT
RISC-V: define the elements of the VCSR vector CSR
riscv: vector: Use vlenb from DT for thead
riscv: Add thead and xtheadvector as a vendor extension
riscv: dts: allwinner: Add xtheadvector to the D1/D1s devicetree
dt-bindings: cpus: add a thead vlen register length property
dt-bindings: riscv: Add xtheadvector ISA extension description
RISC-V: Mark riscv_v_init() as __init
riscv: defconfig: drop RT_GROUP_SCHED=y
riscv/futex: Optimize atomic cmpxchg
riscv: defconfig: enable pinctrl and dwmac support for TH1520
- Support multiple hook locations for maint scripts of Debian package
- Remove 'cpio' from the build tool requirement
- Introduce gendwarfksyms tool, which computes CRCs for export symbols
based on the DWARF information
- Support CONFIG_MODVERSIONS for Rust
- Resolve all conflicts in the genksyms parser
- Fix several syntax errors in genksyms
-----BEGIN PGP SIGNATURE-----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=D553
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Support multiple hook locations for maint scripts of Debian package
- Remove 'cpio' from the build tool requirement
- Introduce gendwarfksyms tool, which computes CRCs for export symbols
based on the DWARF information
- Support CONFIG_MODVERSIONS for Rust
- Resolve all conflicts in the genksyms parser
- Fix several syntax errors in genksyms
* tag 'kbuild-v6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (64 commits)
kbuild: fix Clang LTO with CONFIG_OBJTOOL=n
kbuild: Strip runtime const RELA sections correctly
kconfig: fix memory leak in sym_warn_unmet_dep()
kconfig: fix file name in warnings when loading KCONFIG_DEFCONFIG_LIST
genksyms: fix syntax error for attribute before init-declarator
genksyms: fix syntax error for builtin (u)int*x*_t types
genksyms: fix syntax error for attribute after 'union'
genksyms: fix syntax error for attribute after 'struct'
genksyms: fix syntax error for attribute after abstact_declarator
genksyms: fix syntax error for attribute before nested_declarator
genksyms: fix syntax error for attribute before abstract_declarator
genksyms: decouple ATTRIBUTE_PHRASE from type-qualifier
genksyms: record attributes consistently for init-declarator
genksyms: restrict direct-declarator to take one parameter-type-list
genksyms: restrict direct-abstract-declarator to take one parameter-type-list
genksyms: remove Makefile hack
genksyms: fix last 3 shift/reduce conflicts
genksyms: fix 6 shift/reduce conflicts and 5 reduce/reduce conflicts
genksyms: reduce type_qualifier directly to decl_specifier
genksyms: rename cvar_qualifier to type_qualifier
...
Due to the fact that runtime const ELF sections are named without a
leading period or double underscore, the RSTRIP logic that removes the
static RELA sections from vmlinux fails to identify them. This results
in a situation like below, where some sections that were supposed to get
removed are left behind.
[Nr] Name Type Address Off Size ES Flg Lk Inf Al
[58] runtime_shift_d_hash_shift PROGBITS ffffffff83500f50 2900f50 000014 00 A 0 0 1
[59] .relaruntime_shift_d_hash_shift RELA 0000000000000000 55b6f00 000078 18 I 70 58 8
[60] runtime_ptr_dentry_hashtable PROGBITS ffffffff83500f68 2900f68 000014 00 A 0 0 1
[61] .relaruntime_ptr_dentry_hashtable RELA 0000000000000000 55b6f78 000078 18 I 70 60 8
[62] runtime_ptr_USER_PTR_MAX PROGBITS ffffffff83500f80 2900f80 000238 00 A 0 0 1
[63] .relaruntime_ptr_USER_PTR_MAX RELA 0000000000000000 55b6ff0 000d50 18 I 70 62 8
So tweak the match expression to strip all sections starting with .rel.
While at it, consolidate the logic used by RISC-V, s390 and x86 into a
single shared Makefile library command.
Link: https://lore.kernel.org/all/CAHk-=wjk3ynjomNvFN8jf9A1k=qSc=JFF591W00uXj-qqNUxPQ@mail.gmail.com/
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Charlie Jenkins <charlie@rivosinc.com>
Tested-by: Charlie Jenkins <charlie@rivosinc.com>
Tested-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
- The biggest changes are the TLB flushing scalability optimizations,
to update the mm_cpumask lazily and related changes. This feature
has both a track record and a continued risk of performance regressions,
so it was already delayed by a cycle - but it's all 100% perfect now™.
(Rik van Riel)
- Also miscellaneous fixes and cleanups. (Gautam Somani,
Kirill A. Shutemov, Sebastian Andrzej Siewior)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=g00u
-----END PGP SIGNATURE-----
Merge tag 'x86-mm-2025-01-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 mm updates from Ingo Molnar:
- The biggest changes are the TLB flushing scalability optimizations,
to update the mm_cpumask lazily and related changes.
This feature has both a track record and a continued risk of
performance regressions, so it was already delayed by a cycle - but
it's all 100% perfect now™ (Rik van Riel)
- Also miscellaneous fixes and cleanups. (Gautam Somani, Kirill
Shutemov, Sebastian Andrzej Siewior)
* tag 'x86-mm-2025-01-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Remove unnecessary include of <linux/extable.h>
x86/mtrr: Rename mtrr_overwrite_state() to guest_force_mtrr_state()
x86/mm/selftests: Fix typo in lam.c
x86/mm/tlb: Only trim the mm_cpumask once a second
x86/mm/tlb: Also remove local CPU from mm_cpumask if stale
x86/mm/tlb: Add tracepoint for TLB flush IPI to stale CPU
x86/mm/tlb: Update mm_cpumask lazily
This reverts commit bc7584e009.
The split IPC system calls for o32 have been introduced with modern
version only. Changing this breaks ABI.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
die executes holding the spinlock of &die.lock and unlock
it after printing the oops message.
However in the code if the notify_die() returns NOTIFY_STOP
, die() exit with returning 1 but never unlocked the spinlock.
Fix this by adding spin_unlock_irq(&die.lock) before returning.
Fixes: cf9750bae2 ("Hexagon: Provide basic debugging and system trap support.")
Signed-off-by: Lin Yujun <linyujun809@huawei.com>
Link: https://lore.kernel.org/r/20230522025608.2515558-1-linyujun809@huawei.com
Signed-off-by: Brian Cain <bcain@quicinc.com>
Signed-off-by: Brian Cain <brian.cain@oss.qualcomm.com>
The kernel function prototypes are of no use for userspace and
shouldn't get exposed in an uapi header, so let's move them into
an internal header instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Link: https://lore.kernel.org/r/20240502173818.58152-1-thuth@redhat.com
Signed-off-by: Brian Cain <bcain@quicinc.com>
Signed-off-by: Brian Cain <brian.cain@oss.qualcomm.com>
Null check for 'resource' before assignment is unnecessary because the
variable 'resource' is initialized to NULL at the beginning of the function.
Signed-off-by: Hardevsinh Palaniya <hardevsinh.palaniya@siliconsignals.io>
Link: https://lore.kernel.org/r/20241111142458.67854-1-hardevsinh.palaniya@siliconsignals.io
Signed-off-by: Brian Cain <bcain@quicinc.com>
Signed-off-by: Brian Cain <brian.cain@oss.qualcomm.com>
Sparse reports
net/ipv4/inet_diag.c:1511:17: sparse: sparse: Using plain integer as NULL pointer
Due to this code calling cmpxchg on a non-integer type
struct inet_diag_handler *
return !cmpxchg((const struct inet_diag_handler**)&inet_diag_table[type],
NULL, h) ? 0 : -EEXIST;
While hexagon's cmpxchg assigns an integer value to a variable of this
type.
__typeof__(*(ptr)) __oldval = 0;
Update this assignment to cast 0 to the correct type.
The original issue is easily reproduced at head with the below block,
and is absent after this change.
make LLVM=1 ARCH=hexagon defconfig
make C=1 LLVM=1 ARCH=hexagon net/ipv4/inet_diag.o
Fixes: 99a70aa051 ("Hexagon: Add processor and system headers")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202411091538.PGSTqUBi-lkp@intel.com/
Signed-off-by: Willem de Bruijn <willemb@google.com>
Tested-by: Christian Gmeiner <cgmeiner@igalia.com>
Link: https://lore.kernel.org/r/20241203221736.282020-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Brian Cain <bcain@quicinc.com>
Signed-off-by: Brian Cain <brian.cain@oss.qualcomm.com>