Commit graph

1,264,895 commits

Author SHA1 Message Date
Ping-Ke Shih
1ba63a8a75 wifi: rtw89: 8922a: add chip_ops::cfg_txrx_path
This function is to set TX/RX path. Especially for 1SS rate, it can select
to TX on one or two antenna. Before this operation, stop hardware to
prevent transmitting/receiving unexpected packets. After that, restore
settings and reset hardware to prevent it stays on abnormal state.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240124033637.12330-4-pkshih@realtek.com
2024-02-01 12:19:51 +02:00
Ping-Ke Shih
b16daa6212 wifi: rtw89: 8922a: implement {stop,resume}_sch_tx and cfg_ppdu
To set TX/RX path or set channel, we need these helpers to stop TX and
restore settings. The sch_tx stands for scheduler TX channel, and the
cfg_ppdu is to stop reporting PPDU status, so we should stop them during
setting.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240124033637.12330-3-pkshih@realtek.com
2024-02-01 12:19:51 +02:00
Ping-Ke Shih
f8a7840e98 wifi: rtw89: 8922a: hook handlers of TX/RX descriptors to chip_ops
Hook implemented handlers to chip_ops, and fill packet frequency and signal
strength to RX status from RX PPDU status packet.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240124033637.12330-2-pkshih@realtek.com
2024-02-01 12:19:50 +02:00
André Draszik
21e4e8807b arm64: dts: exynos: gs101: use correct clocks for usi_uart
Wrong pclk clocks have been used in this usi_uart instance here. For
USI and UART, we need the ipclk and pclk, where pclk is the bus clock.
Without it, nothing can work.

It is unclear what exactly is using USI0_UART_CLK, but it is not
required for the IP to be operational at this stage, while pclk is.
This also brings the DT in line with the clock names expected by the
usi and uart drivers.

Fixes: d97b6c902a ("arm64: dts: exynos: gs101: update USI UART to use peric0 clocks")
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Tested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240130093812.1746512-5-andre.draszik@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2024-02-01 11:19:05 +01:00
André Draszik
512b5a875c arm64: dts: exynos: gs101: use correct clocks for usi8
Wrong pclk clocks have been used in this usi8 instance here. For USI
and I2C, we need the ipclk and pclk, where pclk is the bus clock.
Without it, nothing can work.

It is unclear what exactly is using USI8_USI_CLK, but it is not
required for the IP to be operational at this stage, while pclk is.
This also brings the DT in line with the clock names expected by the
usi and i2c drivers.

Fixes: 6d44d1a1fb ("arm64: dts: exynos: gs101: define USI8 with I2C configuration")
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Tested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240130093812.1746512-4-andre.draszik@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2024-02-01 11:19:02 +01:00
Philippe Schenker
3723b56d6f net: dsa: Add KSZ8567 switch support
This commit introduces support for the KSZ8567, a robust 7-port
Ethernet switch. The KSZ8567 features two RGMII/MII/RMII interfaces,
each capable of gigabit speeds, complemented by five 10/100 Mbps
MAC/PHYs.

Signed-off-by: Philippe Schenker <philippe.schenker@impulsing.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240130083419.135763-2-dev@pschenker.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-02-01 11:17:24 +01:00
Philippe Schenker
5f8066d457 dt-bindings: net: dsa: Add KSZ8567 switch support
This commit adds the dt-binding for KSZ8567, a robust 7-port
Ethernet switch. The KSZ8567 features two RGMII/MII/RMII interfaces,
each capable of gigabit speeds, complemented by five 10/100 Mbps
MAC/PHYs.

This binding is necessary to set specific capabilities for this switch
chip that are necessary due to the ksz dsa driver only accepting
specific chip ids.
The KSZ8567 is very similar to KSZ9567 however only containing 100 Mbps
phys on its downstream ports.

Signed-off-by: Philippe Schenker <philippe.schenker@impulsing.ch>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240130083419.135763-1-dev@pschenker.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-02-01 11:17:24 +01:00
Ping-Ke Shih
c108b4a50d wifi: rtw89: pci: enlarge RX DMA buffer to consider size of RX descriptor
Hardware puts RX descriptor and packet in RX DMA buffer, so it could be
over one buffer size if packet size is 11454, and then it will be split
into two segments. WiFi 7 chips use larger size of RX descriptor, so
enlarge DMA buffer size according to RX descriptor to have better
performance and simple flow.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240121071826.10159-5-pkshih@realtek.com
2024-02-01 12:15:42 +02:00
Ping-Ke Shih
0bc7d1d4e6 wifi: rtw89: pci: validate RX tag for RXQ and RPQ
PCI RX ring is a kind of read/write index ring, and DMA and ring index are
asynchronous, so suddenly driver gets newer index ahead before DMA. To
resolve this rare situation, we use a RX tag as helpers to make sure DMA
is done.

The RX tag is a 13-bit value, and range is from 1 ~ 0x1FFF, but 0 isn't
used so should be skipped.

Only enable this validation to coming WiFi 7 chips, because existing
chips use different design and don't really meet this situation.

Add missed rx_ring_eq_is_full for 8851BE by the way.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240121071826.10159-4-pkshih@realtek.com
2024-02-01 12:15:42 +02:00
Zong-Zhe Yang
26cdaee43d wifi: rtw89: pci: interrupt v2 refine IMR for SER
During SER (system error recovery), expect to deal with
only ISR related to halt. So, refine IMR configuration.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240121071826.10159-3-pkshih@realtek.com
2024-02-01 12:15:42 +02:00
Ping-Ke Shih
57b9426952 wifi: rtw89: pci: update SER timer unit and timeout time
Be higher resolution of SER timer unit from 32ms to 16ms to detect
abnormal situation more accurately, and set hardware watchdog timer to 4ms.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240121071826.10159-2-pkshih@realtek.com
2024-02-01 12:15:42 +02:00
Eduard Zingerman
8263b3382d libbpf: Remove unnecessary null check in kernel_supports()
After recent changes, Coverity complained about inconsistent null checks
in kernel_supports() function:

    kernel_supports(const struct bpf_object *obj, ...)
    [...]
    // var_compare_op: Comparing obj to null implies that obj might be null
    if (obj && obj->gen_loader)
        return true;

    // var_deref_op: Dereferencing null pointer obj
    if (obj->token_fd)
        return feat_supported(obj->feat_cache, feat_id);
    [...]

- The original null check was introduced by commit [0], which introduced
  a call `kernel_supports(NULL, ...)` in function bump_rlimit_memlock();
- This call was refactored to use `feat_supported(NULL, ...)` in commit [1].

Looking at all places where kernel_supports() is called:

- There is either `obj->...` access before the call;
- Or `obj` comes from `prog->obj` expression, where `prog` comes from
  enumeration of programs in `obj`;
- Or `obj` comes from `prog->obj`, where `prog` is a parameter to one
  of the API functions:
  - bpf_program__attach_kprobe_opts;
  - bpf_program__attach_kprobe;
  - bpf_program__attach_ksyscall.

Assuming correct API usage, it appears that `obj` can never be null when
passed to kernel_supports(). Silence the Coverity warning by removing
redundant null check.

  [0] e542f2c4cd ("libbpf: Auto-bump RLIMIT_MEMLOCK if kernel needs it for BPF")
  [1] d6dd1d4936 ("libbpf: Further decouple feature checking logic from bpf_object")

Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20240131212615.20112-1-eddyz87@gmail.com
2024-02-01 11:13:45 +01:00
Hugues Fruchet
87f7f576e3 media: arm64: dts: st: add video encoder support to stm32mp255
Add VENC hardware video encoder support to STM32MP255.

Signed-off-by: Hugues Fruchet <hugues.fruchet@foss.st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2024-02-01 11:12:52 +01:00
Hugues Fruchet
d96a6119e3 media: arm64: dts: st: add video decoder support to stm32mp255
Add VDEC hardware video decoder support to STM32MP255.

Signed-off-by: Hugues Fruchet <hugues.fruchet@foss.st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2024-02-01 11:12:29 +01:00
Hugues Fruchet
b0fb9ca30a media: hantro: add support for STM32MP25 VENC
Add support for STM32MP25 VENC video hardware encoder.
Support of JPEG encoding.
VENC has its own reset/clock/irq.

Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@foss.st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2024-02-01 11:12:04 +01:00
Hugues Fruchet
46c4dffb74 media: hantro: add support for STM32MP25 VDEC
Add support for STM32MP25 VDEC video hardware decoder.
Support of H264/VP8 decoding.
No post-processor support.
VDEC has its own reset/clock/irq.

Successfully tested up to full HD.

Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@foss.st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2024-02-01 11:11:33 +01:00
Hugues Fruchet
60314831d2 media: dt-bindings: media: Document STM32MP25 VDEC & VENC video codecs
Add STM32MP25 VDEC video decoder & VENC video encoder bindings.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Hugues Fruchet <hugues.fruchet@foss.st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2024-02-01 11:10:47 +01:00
Alexander Stein
6196fe7775 arm64: dts: imx8qxp: add GPU nodes
Add the DT node for the GPU core found on the i.MX8QXP.

etnaviv-gpu 53100000.gpu: model: GC7000, revision: 6214
[drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 18:08:48 +08:00
Frank Li
5136ea6b10 arm64: dts: imx8qm: Correct edma3 power-domains and interrupt numbers
It is eDMA1 at QM, which have the same register with eDMA3 at qxp.

The below commit fix panic problem.
commit b37e75bddc ("arm64: dts: imx8qm: Add imx8qm's own pm to avoid panic during startup")

This fixes the IRQ and DMA channel numbers. While QM eDMA1 technically has
32 channels, only 10 channels are likely used for I2C. The exact IRQ
numbers for the remaining channels were unclear in the reference manual.

Fixes: e4d7a330fb ("arm64: dts: imx8: add edma[0..3]")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 18:04:25 +08:00
Frank Li
7edee2b297 arm64: dts: imx8qm: Align edma3 power-domains resources indentation
<&pd IMX_SC_R_DMA_1_CH*> is now properly aligned with the previous line
for improved code readability.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 18:04:16 +08:00
Alexander Stein
147896081b arm64: dts: imx8qxp: mba8xx: Add analog audio output on MBa8Xx
Enable SAI1, add the codec to enable LINE_IN and LINE_OUT support on
MBa8Xx on connectors X9 & X10.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 18:02:01 +08:00
Alexander Stein
31769bf351 arm64: dts: imx8qxp: Add mclkout clock gates
These clock gates provide a clock output on ACM_MCLK_OUT pads. They are
intended to be used as MCLK for SAI0-3.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 18:01:59 +08:00
Alexander Stein
0a9279e9ae arm64: dts: imx8qxp: Add audio SAI nodes
This adds the sai nodes attached to aips1 bus. These can be shared with
imx8qm as well. Input clock from ACM is always feed to mclk1 only. Others
are unused and are connected to a dummy clock.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 18:01:56 +08:00
Alexander Stein
2b7112eafd arm64: dts: imx8qxp: Add audio clock mux node
The audio clock mux (ACM) selects the input clock for each attached
consumer, referenced by clock-cell.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 18:01:38 +08:00
Alexander Stein
951cd070fd arm64: dts: imx8qxp: Add ACM input clock gates
These clock gates provide input clocks for ACM. They can be selected by
IMX_ADMA_ACM_* macros. As SAI driver does not provide Tx/Rx bitclock
clocks yet, add dummy clocks for the unimplemented inputs.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 18:01:17 +08:00
Alexander Stein
71363a485a arm64: dts: freescale: add initial device tree for TQMa8Xx
This adds support for TQMa8XQP and TQMa8XDP modules on MBa8Xx board.
As the only difference is the mounted SoC, both module and baseboard
files are shared.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 17:59:46 +08:00
André Draszik
8a96d2701f clk: samsung: gs101: gpio_peric0_pclk needs to be kept on
This pclk clock is required any time we access the pinctrl registers of
this block.

Since pinctrl-samsung doesn't support a clock at the moment, we just
keep the kernel from disabling it at boot, until we have an update for
pinctrl-samsung to handle this required clock, at which point we'll be
able to drop the flag again.

Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240130093812.1746512-2-andre.draszik@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2024-02-01 10:56:19 +01:00
Johannes Berg
aa125f2290 wifi: iwlwifi: remove extra kernel-doc
This no longer exists, remove the kernel-doc.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240128102209.d2192d79bc09.Id9551728d618248dd471382a5283503a8976237a@changeid
2024-02-01 11:54:33 +02:00
Alexander Stein
970dd89c53 arm64: defconfig: Enable i.MX8QXP device drivers
These drivers are used on i.MX8QXP based devices.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 17:46:51 +08:00
Alexander Stein
cc605a4c12 dt-bindings: arm: add TQMa8Xx boards
TQMa8Xx is a SOM series featuring NXP i.MX8X SoC.
They are called TQMa8XQP and TQMa8XDP respectively.
MBa8Xx is an evaluation mainboard for this SOM

Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 17:46:34 +08:00
Alexander Stein
95549bba87 arm64: dts: imx: add imx8dxp support
i.MX 8DualXPlus is a dual (2x) Cortex-A35 processor with powerful
graphic and multimedia features. This patch adds the SoC dtsi, based on
imx8qxp removing the additional CPU cores. Peripherals are identical.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 17:43:50 +08:00
Krzysztof Kozlowski
b2005bb756 dt-bindings: net: qcom,ipa: do not override firmware-name $ref
dtschema package defines firmware-name as string-array, so individual
bindings should not make it a string but instead just narrow the number
of expected firmware file names.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20240129142121.102450-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-02-01 10:40:12 +01:00
Thomas Hellström
5bd24e7882 drm/xe/vm: Subclass userptr vmas
The construct allocating only parts of the vma structure when
the userptr part is not needed is very fragile. A developer could
add additional fields below the userptr part, and the code could
easily attempt to access the userptr part even if its not persent.

So introduce xe_userptr_vma which subclasses struct xe_vma the
proper way, and accordingly modify a couple of interfaces.
This should also help if adding userptr helpers to drm_gpuvm.

v2:
- Fix documentation of to_userptr_vma() (Matthew Brost)
- Fix allocation and freeing of vmas to clearer distinguish
  between the types.

Closes: https://lore.kernel.org/intel-xe/0c4cc1a7-f409-4597-b110-81f9e45d1ffe@embeddedor.com/T/#u
Fixes: a4cc60a55f ("drm/xe: Only alloc userptr part of xe_vma for userptrs")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240131091628.12318-1-thomas.hellstrom@linux.intel.com
2024-02-01 09:49:26 +01:00
Frieder Schrempf
6f5e6d7306 arm64: dts: imx8mm-kontron: Refactor devicetree for OSM-S module and board
The OSM spec defines dedicated functions for all pads of the SoM.
Therefore we can assume that carrier board designs stick to these
definitions and extend the SoM devicetree include with matching
default nodes and pinmux settings.

This way we can reduce the overhead and redundancy in the carrier
board devicetrees while still sticking to the policy of separating
board and module description.

Even if the carrier board design deviates slightly from the spec it
can define its own pinmux definitions and use them as necessary or
even disable unused nodes from the SoM devicetree.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 15:21:23 +08:00
Frieder Schrempf
7e349e0fe3 arm64: dts: imx8mm-kontron: Add I2C EEPROM on OSM-S Kontron i.MX8MM
There is an EEPROM on the SoM module. Add it to the description.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 15:21:21 +08:00
Frieder Schrempf
0e8c45ef09 arm64: dts: imx8mm-kontron: Remove useless trickle-diode-disable from RTC node
The RV3028 driver doesn't use this property. Remove it.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 15:21:19 +08:00
Frieder Schrempf
5798bb7164 arm64: dts: imx8mm-kontron: Disable uneffective PUE bit in SDIO IOMUX
The PUE bit is only effective if the PE bit is also set. To avoid
confusion, disable the PUE bit if it is not needed.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 15:21:16 +08:00
Frieder Schrempf
360b9dcf65 arm64: dts: imx8mm-kontron: Fix OSM-S devicetrees to match latest hardware
The current state of the devicetree for the i.MX8MM OSM-S and the BL
baseboard reflects deprecated prototype hardware. Update the board
description to match the latest hardware revision.

As the old hardware is not available anymore, was only produced in
very small quantities and was broken in some ways, we can safely
fixup the original devicetree.

Fixes: de9618e84f ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 15:21:13 +08:00
Frieder Schrempf
8d0f39b7d0 arm64: dts: imx8mm-kontron: Fix interrupt for RTC on OSM-S i.MX8MM module
The level of the interrupt signal is active low instead. Fix this.

Fixes: de9618e84f ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 15:21:10 +08:00
Frieder Schrempf
0088205248 arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL board
Some signals have external pullup resistors on the board and don't need
the internal ones to be enabled. Due to silicon errata ERR050080 let's
disable the internal pull resistors whererever possible and prevent
any unwanted behavior in case they wear out.

Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 15:21:07 +08:00
Frieder Schrempf
5a940ba3e4 arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL OSM-S board
Some signals have external pullup resistors on the board and don't need
the internal ones to be enabled. Due to silicon errata ERR050080 let's
disable the internal pull resistors whererever possible and prevent
any unwanted behavior in case they wear out.

Fixes: de9618e84f ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 15:21:04 +08:00
Frieder Schrempf
162aadaa0d arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL board
These signals are actively driven by the SoC or by the onboard
transceiver. There's no need to enable the internal pull resistors
and due to silicon errata ERR050080 let's disable the internal ones
to prevent any unwanted behavior in case they wear out.

Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 15:21:01 +08:00
Frieder Schrempf
c6d9b5672a arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL OSM-S board
These signals are actively driven by the SoC or by the onboard
transceiver. There's no need to enable the internal pull resistors
and due to silicon errata ERR050080 let's disable the internal ones
to prevent any unwanted behavior in case they wear out.

Fixes: de9618e84f ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 15:20:59 +08:00
Frieder Schrempf
f19e5bb91d arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on SL/BL i.MX8MM
There are external pullup resistors on the board and due to silicon
errata ERR050080 let's disable the internal ones to prevent any
unwanted behavior in case they wear out.

Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 15:20:56 +08:00
Frieder Schrempf
96293af54f arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on OSM-S i.MX8MM
There are external pullup resistors on the board and due to silicon
errata ERR050080 let's disable the internal ones to prevent any
unwanted behavior in case they wear out.

Fixes: de9618e84f ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-02-01 15:20:26 +08:00
Moudy Ho
9288eae430 media: platform: mtk-mdp3: add support for parallel pipe to improve FPS
In some chips, MDP3 has the ability to utilize two pipelines to
parallelly process a single frame.
To enable this feature, multiple CMDQ clients and packets need to
be configured at the same time.

Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2024-02-01 07:53:49 +01:00
Moudy Ho
0e9bd2fcda media: platform: mtk-mdp3: add mt8195 MDP3 component settings
Extend the component settings used in MT8195 MDP3.
Additionally, it is crucial to read all component settings in
a specific manner to ensure that shared memory data structure lengths
are aligned across different platforms.

Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2024-02-01 07:52:17 +01:00
Moudy Ho
51d918d62b media: platform: mtk-mdp3: add mt8195 shared memory configurations
The configuration of the MT8195 components in the shared memory
is defined in the header file "mdp_sm_mt8195.h".

Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2024-02-01 07:50:03 +01:00
Moudy Ho
adce64c4ce media: platform: mtk-mdp3: add mt8195 platform configuration
Add MT8195 MDP3 basic configuration in file "mdp_cfg_data.c"
and corresponding driver data.

Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2024-02-01 07:45:05 +01:00
Moudy Ho
d97fd41e83 media: platform: mtk-mdp3: add support for blending multiple components
Certain chips can combine several components to form complex virtual
units with advanced functions.
These components require simultaneous configuration of their MODs and
clocks.

Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2024-02-01 07:44:14 +01:00