Fix some errors in the Marvell MV88E6xxx switch descriptions:
- The top node had no address size or cells.
- switch0@0 is not OK, should be ethernet-switch@0.
- The ports node should be named ethernet-ports
- The ethernet-ports node should have port@0 etc children, no
plural "ports" in the children.
- Ports should be named ethernet-port@0 etc
- PHYs should be named ethernet-phy@0 etc
This serves as an example of fixes needed for introducing a
schema for the bindings, but the patch can simply be applied.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
While doing some code cleanup in drivers/bus/, I noticed that the file
drivers/bus/mvebu-mbus.c has no maintainer.
Although the file has not been touched a lot lately, the git history tells
us that Gregory Clement and Andrew Lunn integrated patches specific to
this driver code. Further, the driver's config depends on config
PLAT_ORION, and the code for this platform is defined in
arch/arm/plat-orion/, which is part of ARM/Marvell Dove/MV78xx0/Orion SOC
support with Gregory and Andrew already being its maintainer.
Add drivers/bus/mvebu-mbus.c to ARM/Marvell Dove/MV78xx0/Orion SOC support.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
As the ring buffer recording requires cmpxchg() to work, if the
architecture does not support cmpxchg in NMI, then do not do any recording
within an NMI.
Link: https://lore.kernel.org/linux-trace-kernel/20231213175403.6fc18540@gandalf.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Add an Intel specific hook into machine_check_poll() to keep track of
per-CPU, per-bank corrected error logs (with a stub for the
CONFIG_MCE_INTEL=n case).
When a storm is observed the rate of interrupts is reduced by setting
a large threshold value for this bank in IA32_MCi_CTL2. This bank is
added to the bitmap of banks for this CPU to poll. The polling rate is
increased to once per second.
When a storm ends reset the threshold in IA32_MCi_CTL2 back to 1, remove
the bank from the bitmap for polling, and change the polling rate back
to the default.
If a CPU with banks in storm mode is taken offline, the new CPU that
inherits ownership of those banks takes over management of storm(s) in
the inherited bank(s).
The cmci_discover() function was already very large. These changes
pushed it well over the top. Refactor with three helper functions to
bring it back under control.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20231115195450.12963-4-tony.luck@intel.com
This is the core functionality to track CMCI storms at the machine check
bank granularity. Subsequent patches will add the vendor specific hooks
to supply input to the storm detection and take actions on the start/end
of a storm.
machine_check_poll() is called both by the CMCI interrupt code, and for
periodic polls from a timer. Add a hook in this routine to maintain
a bitmap history for each bank showing whether the bank logged an
corrected error or not each time it is polled.
In normal operation the interval between polls of these banks determines
how far to shift the history. The 64 bit width corresponds to about one
second.
When a storm is observed a CPU vendor specific action is taken to reduce
or stop CMCI from the bank that is the source of the storm. The bank is
added to the bitmap of banks for this CPU to poll. The polling rate is
increased to once per second. During a storm each bit in the history
indicates the status of the bank each time it is polled. Thus the
history covers just over a minute.
Declare a storm for that bank if the number of corrected interrupts seen
in that history is above some threshold (defined as 5 in this series,
could be tuned later if there is data to suggest a better value).
A storm on a bank ends if enough consecutive polls of the bank show no
corrected errors (defined as 30, may also change). That calls the CPU
vendor specific function to revert to normal operational mode, and
changes the polling rate back to the default.
[ bp: Massage. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20231115195450.12963-3-tony.luck@intel.com
The rb_time_cmpxchg() on 32-bit architectures requires setting three
32-bit words to represent the 64-bit timestamp, with some salt for
synchronization. Those are: msb, top, and bottom
The issue is, the rb_time_cmpxchg() did not properly salt the msb portion,
and the msb that was written was stale.
Link: https://lore.kernel.org/linux-trace-kernel/20231215084114.20899342@rorschach.local.home
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Fixes: f03f2abce4 ("ring-buffer: Have 32 bit time stamps use all 64 bits")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
In 'rt2x00queue_create_tx_descriptor()', there is no need to call
'ieee80211_get_rts_cts_rate()' while checking for RTS/CTS frame
since this function returns NULL or pointer to internal bitrate
table entry, and the return value is not actually used. Compile
tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213051449.126963-1-dmantipov@yandex.ru
The following race can cause rb_time_read() to observe a corrupted time
stamp:
rb_time_cmpxchg()
[...]
if (!rb_time_read_cmpxchg(&t->msb, msb, msb2))
return false;
if (!rb_time_read_cmpxchg(&t->top, top, top2))
return false;
<interrupted before updating bottom>
__rb_time_read()
[...]
do {
c = local_read(&t->cnt);
top = local_read(&t->top);
bottom = local_read(&t->bottom);
msb = local_read(&t->msb);
} while (c != local_read(&t->cnt));
*cnt = rb_time_cnt(top);
/* If top and msb counts don't match, this interrupted a write */
if (*cnt != rb_time_cnt(msb))
return false;
^ this check fails to catch that "bottom" is still not updated.
So the old "bottom" value is returned, which is wrong.
Fix this by checking that all three of msb, top, and bottom 2-bit cnt
values match.
The reason to favor checking all three fields over requiring a specific
update order for both rb_time_set() and rb_time_cmpxchg() is because
checking all three fields is more robust to handle partial failures of
rb_time_cmpxchg() when interrupted by nested rb_time_set().
Link: https://lore.kernel.org/lkml/20231211201324.652870-1-mathieu.desnoyers@efficios.com/
Link: https://lore.kernel.org/linux-trace-kernel/20231212193049.680122-1-mathieu.desnoyers@efficios.com
Fixes: f458a14534 ("ring-buffer: Test last update in 32bit version of __rb_time_read()")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Mathieu Desnoyers pointed out an issue in the rb_time_cmpxchg() for 32 bit
architectures. That is:
static bool rb_time_cmpxchg(rb_time_t *t, u64 expect, u64 set)
{
unsigned long cnt, top, bottom, msb;
unsigned long cnt2, top2, bottom2, msb2;
u64 val;
/* The cmpxchg always fails if it interrupted an update */
if (!__rb_time_read(t, &val, &cnt2))
return false;
if (val != expect)
return false;
<<<< interrupted here!
cnt = local_read(&t->cnt);
The problem is that the synchronization counter in the rb_time_t is read
*after* the value of the timestamp is read. That means if an interrupt
were to come in between the value being read and the counter being read,
it can change the value and the counter and the interrupted process would
be clueless about it!
The counter needs to be read first and then the value. That way it is easy
to tell if the value is stale or not. If the counter hasn't been updated,
then the value is still good.
Link: https://lore.kernel.org/linux-trace-kernel/20231211201324.652870-1-mathieu.desnoyers@efficios.com/
Link: https://lore.kernel.org/linux-trace-kernel/20231212115301.7a9c9a64@gandalf.local.home
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Fixes: 10464b4aa6 ("ring-buffer: Add rb_time_t 64 bit operations for speeding up 32 bit")
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
The new WiFi 7 chips change the design, so no need to disable/enable
BB/RF when core_start(). Keep the same logic for existing chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231211083341.118047-7-pkshih@realtek.com
To support MLO of WiFi 7, we should configure hardware as DBCC mode, and
notify this status to firmware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231211083341.118047-6-pkshih@realtek.com
Many existing MAC access functions are used by WiFi 6 chips only, so add
suffix _ax to be clearer. Some are common and can be used by WiFi 7, so
export this kind of functions. This patch doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231211083341.118047-5-pkshih@realtek.com
Before accessing CMAC and DMAC registers, we should ensure they have been
powered on, so add flag to determine the state. For old chips, we read
registers and check corresponding bit, but it takes extra cost to read.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231211083341.118047-4-pkshih@realtek.com
The power on/off functions are to turn on hardware function blocks and
to turn off them if we are going to stay in idle state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231211083341.118047-3-pkshih@realtek.com
The XTAL SI is a serial interface to indirectly access registers of
analog hardware circuit. Since WiFi 7 chips use different registers, add
a ops to access them via common functions. This patch doesn't change logic
for existing chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231211083341.118047-2-pkshih@realtek.com
With formatted string loaded from firmware file, we can use the formatted
string ID and get corresponding string, and then use regular rtw89_debug()
to show the message if debug mask of RFK is enabled.
If the string ID doesn't present, fallback to print plain hexadecimal.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213005054.10568-7-pkshih@realtek.com
RFK log events contains two types. One called RUN log is to reflect state
during RFK is running, and it replies on formatted string loaded from
firmware file, but print this type as plain hexadecimal only in this patch.
The other is REPORT log that reflects the final result of a RFK, and
each calibration has its own struct to carry many specific information.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213005054.10568-6-pkshih@realtek.com
Trigger a RFK (RF calibration) in firmware by a H2C command, and in
progress it reports log and a result finally by C2H events. Firstly, add
prototype of the C2H event handlers to have a simple picture of framework.
The callers who trigger H2C will wait until a C2H event is received,
so we must process these C2H events in receiving process. Thus, mark this
kind of C2H events as atomic. Also, timestamp is also useful for
debugging, mark C2H events carrying RFK log as atomic as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213005054.10568-5-pkshih@realtek.com
To debug RFK (RF calibration) in firmware, it sends log via firmware C2H
events to driver with string format ID and four arguments. Load formatted
string from firmware file, and the string ID can get back its string. Then,
use regular print format to show the message.
This firmware element layout looks like
+============================================+
| elm ID | elm size | version | |
+----------+----------+----------+-----------+
| | nr |rsvd |rfk_id|rsvd|
+--------------------------------------------+
| offset[] (__le16 * nr) |
| ... |
+--------------------------------------------+
| formatted string with null termintor (*nr) |
| ... |
+============================================+
* a firmware file can contains more than one elements with this element ID
named RTW89_FW_ELEMENT_ID_RFKLOG_FMT (19), because many RFK needs its
own formatted strings, so add 'rfk_id' to know it belongs to which RFK.
* the 'formatted string' just follow 'offset[]' without padding to align
32bits.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213005054.10568-4-pkshih@realtek.com
8922AE has more than one hardware version, and they use different BB MCU
firmware, so occupy a byte from element priv[] to annotate version. Since
there are more than one firmware and only matched version is adopted,
return 1 to ignore not matched firmware.
+===========================================+
| elm ID | elm size | version | |
+----------+----------+----------+----------+
| | element_priv[] |
+-------------------------------------------+
change to |
v
+===========================================+
| elm ID | elm size | version | |
+----------+----------+----------+----------+
| | cv | element_rsvd[] |
+-------------------------------------------+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213005054.10568-3-pkshih@realtek.com
The TX power track tables are used to define compensation power reflected
to thermal value. Currently, we have 16 (2 * 4 * 2) tables made by
combinations of
{negative/positive thermal value, 2GHz/2GHz-CCK/5GHz/6GHz, path A/B}
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213005054.10568-2-pkshih@realtek.com
When filtering is enabled, a temporary buffer is created to place the
content of the trace event output so that the filter logic can decide
from the trace event output if the trace event should be filtered out or
not. If it is to be filtered out, the content in the temporary buffer is
simply discarded, otherwise it is written into the trace buffer.
But if an interrupt were to come in while a previous event was using that
temporary buffer, the event written by the interrupt would actually go
into the ring buffer itself to prevent corrupting the data on the
temporary buffer. If the event is to be filtered out, the event in the
ring buffer is discarded, or if it fails to discard because another event
were to have already come in, it is turned into padding.
The update to the write_stamp in the rb_try_to_discard() happens after a
fix was made to force the next event after the discard to use an absolute
timestamp by setting the before_stamp to zero so it does not match the
write_stamp (which causes an event to use the absolute timestamp).
But there's an effort in rb_try_to_discard() to put back the write_stamp
to what it was before the event was added. But this is useless and
wasteful because nothing is going to be using that write_stamp for
calculations as it still will not match the before_stamp.
Remove this useless update, and in doing so, we remove another
cmpxchg64()!
Also update the comments to reflect this change as well as remove some
extra white space in another comment.
Link: https://lore.kernel.org/linux-trace-kernel/20231215081810.1f4f38fe@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Joel Fernandes <joel@joelfernandes.org>
Cc: Vincent Donnefort <vdonnefort@google.com>
Fixes: b2dd797543 ("ring-buffer: Force absolute timestamp on discard of event")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
If an update to an event is interrupted by another event between the time
the initial event allocated its buffer and where it wrote to the
write_stamp, the code try to reset the write stamp back to the what it had
just overwritten. It knows that it was overwritten via checking the
before_stamp, and if it didn't match what it wrote to the before_stamp
before it allocated its space, it knows it was overwritten.
To put back the write_stamp, it uses the before_stamp it read. The problem
here is that by writing the before_stamp to the write_stamp it makes the
two equal again, which means that the write_stamp can be considered valid
as the last timestamp written to the ring buffer. But this is not
necessarily true. The event that interrupted the event could have been
interrupted in a way that it was interrupted as well, and can end up
leaving with an invalid write_stamp. But if this happens and returns to
this context that uses the before_stamp to update the write_stamp again,
it can possibly incorrectly make it valid, causing later events to have in
correct time stamps.
As it is OK to leave this function with an invalid write_stamp (one that
doesn't match the before_stamp), there's no reason to try to make it valid
again in this case. If this race happens, then just leave with the invalid
write_stamp and the next event to come along will just add a absolute
timestamp and validate everything again.
Bonus points: This gets rid of another cmpxchg64!
Link: https://lore.kernel.org/linux-trace-kernel/20231214222921.193037a7@gandalf.local.home
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Joel Fernandes <joel@joelfernandes.org>
Cc: Vincent Donnefort <vdonnefort@google.com>
Fixes: a389d86f7f ("ring-buffer: Have nested events still record running time stamp")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
AP BSSID configuration is missing at AP start. Without this fix, FW returns
STA interface MAC address after first init. When hostapd restarts, it gets MAC
address from netdev before driver sets STA MAC to netdev again. Now MAC address
between hostapd and net interface are different causes STA cannot connect to
AP. After that MAC address of uap0 mlan0 become the same. And issue disappears
after following hostapd restart (another issue is AP/STA MAC address become the
same).
This patch fixes the issue cleanly.
Signed-off-by: David Lin <yu-hao.lin@nxp.com>
Fixes: 12190c5d80 ("mwifiex: add cfg80211 start_ap and stop_ap handlers")
Cc: stable@vger.kernel.org
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Rafael Beims <rafael.beims@toradex.com> # Verdin iMX8MP/SD8997 SD
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231215005118.17031-1-yu-hao.lin@nxp.com
MOXA PCIe RS422/RS485 boards will not function by default because of the
initial default serial interface of all MOXA PCIe boards is set to
RS232.
This patch fixes the problem above by setting the initial default serial
interface to RS422 for those MOXA RS422/RS485 PCIe boards.
Signed-off-by: Crescent CY Hsieh <crescentcy.hsieh@moxa.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20231214060234.6147-1-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On this platform, different vendor data is used. That requires a
compile-time check as we access (1) a global boolean & (2) our local
vendor data. Both symbols are accessible only when
CONFIG_ACPI_SPCR_TABLE is enabled.
Factor the vendor data overriding to a separate function that is empty
when CONFIG_ACPI_SPCR_TABLE is not defined.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20231207-mbly-uart-v6-8-e384afa5e78c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The whole function body is encapsulated inside an if-condition. Reverse
the if logic and early return to remove one indentation level.
Also turn two nested ifs into a single one at the end of the function.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20231207-mbly-uart-v6-7-e384afa5e78c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following messages from checkpatch:
$ ./scripts/checkpatch.pl --strict --file \
drivers/tty/serial/amba-pl011.c
ERROR: do not initialise statics to false
WARNING: Possible unnecessary 'out of memory' message
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: Prefer [subsystem eg: netdev]_info([subsystem]dev, ... then
dev_info(dev, ... then pr_info(... to
CHECK: Prefer using the BIT macro
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20231207-mbly-uart-v6-6-e384afa5e78c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following checkpatch warnings & checks:
$ ./scripts/checkpatch.pl --strict --file \
drivers/tty/serial/amba-pl011.c
CHECK: Unbalanced braces around else statement
CHECK: Unnecessary parentheses around '[...]'
CHECK: braces {} should be used on all arms of this statement
CHECK: Comparison to NULL could be written "[...]"
WARNING: Comparisons should place the constant on the right side of the test
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20231207-mbly-uart-v6-5-e384afa5e78c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver uses two TIOCMBIT macros inside pl011_{get,set}_mctrl to
simplify the logic. Those look scary to checkpatch because they contain
ifs without do-while loops.
Avoid the macros by creating small equivalent static functions; that
lets the compiler do its type checking & avoids checkpatch errors.
For the second instance __assign_bit is not usable because it deals with
unsigned long pointers whereas we have an unsigned int in
pl011_set_mctrl.
This addresses the following checkpatch warnings:
$ ./scripts/checkpatch.pl --strict --file \
drivers/tty/serial/amba-pl011.c
ERROR: Macros starting with if should be enclosed by a do -
while loop to avoid possible if/else logic defects
CHECK: Macro argument 'uartbit' may be better as '(uartbit)' to
avoid precedence issues
ERROR: Macros starting with if should be enclosed by a do - while
loop to avoid possible if/else logic defects
CHECK: Macro argument 'tiocmbit' may be better as '(tiocmbit)' to
avoid precedence issues
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20231207-mbly-uart-v6-3-e384afa5e78c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Follow recommandations from:
$ ./scripts/checkpatch.pl --strict --file \
drivers/tty/serial/amba-pl011.c
We fix 5 warnings and 48 checks, all related to whitespace.
Culprits are:
CHECK: Alignment should match open parenthesis
CHECK: Blank lines aren't necessary after an open brace '{'
CHECK: Lines should not end with a '('
CHECK: Please don't use multiple blank lines
CHECK: Please use a blank line after function/struct/union/enum
declarations
CHECK: spaces preferred around that '/' (ctx:VxV)
CHECK: spaces preferred around that '|' (ctx:VxV)
WARNING: Missing a blank line after declarations
WARNING: please, no spaces at the start of a line
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20231207-mbly-uart-v6-2-e384afa5e78c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver uses bit shifts and hexadecimal expressions to declare
constants. Replace that with the BIT(), GENMASK() & FIELD_PREP_CONST()
macros to clarify intent.
include/linux/amba/serial.h gets included from arch/arm/include/debug/pl01x.S.
Avoid includes and macro tricks for the four defines that are involved:
UART01x_DR, UART01x_FR, UART01x_FR_TXFF and UART01x_FR_BUSY.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20231207-mbly-uart-v6-1-e384afa5e78c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For SDIO IW416, due to a bug, FW may return ready before complete full
initialization. Command timeout may occur at driver load after reboot.
Workaround by adding 100ms delay at checking FW status.
Signed-off-by: David Lin <yu-hao.lin@nxp.com>
Cc: stable@vger.kernel.org
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Verdin AM62 (IW416)
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231208234029.2197-1-yu-hao.lin@nxp.com
It can happen that while a break is received the transmitter gets empty
and IIR signals a Transmitter holding register empty (THRI) event. In
this case it's too early for the break workaround. Still doing it then
results in the THRI event not being rereported which makes the driver
miss that and e.g. for RS485 half-duplex communication it fails to
switch back to RX mode.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231213174312.2341013-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UMS9620 also uses the same serial device with SC9836.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20231215085630.984892-4-chunyan.zhang@unisoc.com
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cc4c1d05eb ("sc16is7xx: Properly resume TX after stop") changed
behavior to unconditionnaly set the THRI interrupt in sc16is7xx_tx_proc().
For example when sending a 65 bytes message, and assuming the Tx FIFO is
initially empty, sc16is7xx_handle_tx() will write the first 64 bytes of the
message to the FIFO and sc16is7xx_tx_proc() will then activate THRI. When
the THRI IRQ is fired, the driver will write the remaining byte of the
message to the FIFO, and disable THRI by calling sc16is7xx_stop_tx().
When sending a 2 bytes message, sc16is7xx_handle_tx() will write the 2
bytes of the message to the FIFO and call sc16is7xx_stop_tx(), disabling
THRI. After sc16is7xx_handle_tx() exits, control returns to
sc16is7xx_tx_proc() which will unconditionally set THRI. When the THRI IRQ
is fired, the driver simply acknowledges the interrupt and does nothing
more, since all the data has already been written to the FIFO. This results
in 2 register writes and 4 register reads all for nothing and taking
precious cycles from the I2C/SPI bus.
Fix this by enabling the THRI interrupt only when we fill the Tx FIFO to
its maximum capacity and there are remaining bytes to send in the message.
Fixes: cc4c1d05eb ("sc16is7xx: Properly resume TX after stop")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231211171353.2901416-7-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SC16IS7XX IC supports a burst mode to access the FIFOs where the
initial register address is sent ($00), followed by all the FIFO data
without having to resend the register address each time. In this mode, the
IC doesn't increment the register address for each R/W byte.
The regmap_raw_read() and regmap_raw_write() are functions which can
perform IO over multiple registers. They are currently used to read/write
from/to the FIFO, and although they operate correctly in this burst mode on
the SPI bus, they would corrupt the regmap cache if it was not disabled
manually. The reason is that when the R/W size is more than 1 byte, these
functions assume that the register address is incremented and handle the
cache accordingly.
Convert FIFO R/W functions to use the regmap _noinc_ versions in order to
remove the manual cache control which was a workaround when using the
_raw_ versions. FIFO registers are properly declared as volatile so
cache will not be used/updated for FIFO accesses.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231211171353.2901416-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver has been converted to use one regmap per port, change
efr locking to operate on a channel basis instead of on the whole IC.
Fixes: 3837a03795 ("serial: sc16is7xx: improve regmap debugfs by using one regmap per port")
Cc: <stable@vger.kernel.org> # 6.1.x: 3837a03 serial: sc16is7xx: improve regmap debugfs by using one regmap per port
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231211171353.2901416-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver has been converted to use one regmap per port, the line
structure member is no longer used, so remove it.
Fixes: 3837a03795 ("serial: sc16is7xx: improve regmap debugfs by using one regmap per port")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231211171353.2901416-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>