Alexander Lobakin says:
====================
idpf: add get/set for Ethtool's header split ringparam
Currently, the header split feature (putting headers in one smaller
buffer and then the data in a separate bigger one) is always enabled
in idpf when supported.
One may want to not have fragmented frames per each packet, for example,
to avoid XDP frags. To better optimize setups for particular workloads,
add ability to switch the header split state on and off via Ethtool's
ringparams, as well as to query the current status.
There's currently only GET in the Ethtool Netlink interface for now,
so add SET first. I suspect idpf is not the only one supporting this.
====================
Link: https://lore.kernel.org/r/20231212142752.935000-1-aleksander.lobakin@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
idpf supports the header split feature and that feature is always
enabled by default.
However, for flexibility reasons and to simplify some scenarios, it
would be useful to have the support for switching the header split
off (and on) from the userspace.
Address that need by adding the user config parameter, the functions
for disabling (or enabling) the header split feature, and calls to
them from the Ethtool ringparam callbacks.
It still is enabled by default if supported by the hardware.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Co-developed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://lore.kernel.org/r/20231212142752.935000-3-aleksander.lobakin@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Follow up commit 9690ae6042 ("ethtool: add header/data split
indication") and add the set part of Ethtool's header split, i.e.
ability to enable/disable header split via the Ethtool Netlink
interface. This might be helpful to optimize the setup for particular
workloads, for example, to avoid XDP frags, and so on.
A driver should advertise ``ETHTOOL_RING_USE_TCP_DATA_SPLIT`` in its
ops->supported_ring_params to allow doing that. "Unknown" passed from
the userspace when the header split is supported means the driver is
free to choose the preferred state.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://lore.kernel.org/r/20231212142752.935000-2-aleksander.lobakin@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SoC runs at a high enough voltage to support overdrive
mode, so include the imx8mm-overdrive.dtsi file to increase
the VPU and GPU clocks to their overdrive speeds.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
For boards who run their SoC at a higher voltage than nominal,
the boards can run several clocks at an overdrive rate for
better performance. Add an optional DTSI file which can be
included by various boards to run in overdrive mode.
This raises the GPU PLL to 1000MHz, and the VPU PLL to
700MHz while moving VPU_G1 and VPU_H1 to the SYS_PLL3_OUT
which runs at 750MHz.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When the GPU nodes were added, the GPU_PLL_OUT was configured
for 1000MHz, but this requires the SoC to run in overdrive mode
which requires an elevated voltage operating point.
Since this may run some boards out of spec, the default clock
should be set to 800MHz for nominal operating mode. Boards
that run at the higher voltage can update their clocks
accordingly.
Fixes: 4523be8e46 ("arm64: dts: imx8mm: Add GPU nodes for 2D and 3D core")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
TCP got MSG_EOR support in linux-4.7.
This is a canonical way of making sure no coalescing
will be performed on the skb, even if it could not be
immediately sent.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20231212110608.3673677-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fsl,micfil.yaml defines the clock-names in the following sequence:
clock-names:
items:
- const: ipg_clk
- const: ipg_clk_app
- const: pll8k
- const: pll11k
- const: clkext3
minItems: 2
imx93.dtsi currently misses the 'pll11k' entry and jump to 'clkext3'.
This leads to the following dt-schema warning:
imx93-11x11-evk.dtb: micfil@44520000: clock-names:3: 'pll11k' was expected
from schema $id: http://devicetree.org/schemas/sound/fsl,micfil.yaml#
Fix the warning by describing the clocks up to 'pll8k' as 'clkext3'
is assigned to a dummy clock.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per fsl,mxs-dma.yaml, the node name should be 'dma-controller'.
Change it to fix the following dt-schema warning.
imx28-apf28.dtb: dma-apbx@80024000: $nodename:0: 'dma-apbx@80024000' does not match '^dma-controller(@.*)?$'
from schema $id: http://devicetree.org/schemas/dma/fsl,mxs-dma.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'gpios' property to describe the SDA and SCL GPIOs is considered
deprecated according to i2c-gpio.yaml.
Switch to the preferred 'sda-gpios' and 'scl-gpios' properties.
This fixes the following schema warnings:
imx23-sansa.dtb: i2c-0: 'sda-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
imx23-sansa.dtb: i2c-0: 'scl-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per leds-gpio.yaml, the led names should start with 'led'.
Change it to fix the following dt-schema warning:
imx27-apf27dev.dtb: leds: 'user' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Swap is a function interface that provides exchange function. To avoid
code duplication, we can use swap function.
./drivers/net/ethernet/mellanox/mlx5/core/steering/dr_action.c:1254:50-51: WARNING opportunity for swap().
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=7580
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add a getter for the number of participants in a devcom
component (those who share the same component id and key).
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Make CQ struct and methods independent of "priv", use more basic
arguments instead.
This will ease the transition to netdev with multiple mdevs.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Turn some of the struct auxiliary_driver ops into wrappers to stop
having dummy local vars passed as unused arguments.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Function usage is limited to the monitor_stats.c file, do not expose it.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The transport interface send (TIS) object is responsible for performing
all transport related operations of the transmit side. Messages from
Send Queues get segmented and transmitted by the TIS including all
transport required implications, e.g. in the case of large send offload,
the TIS is responsible for the segmentation.
These are stateless objects and can be used by multiple netdevs (e.g.
representors) who share the same core device.
Providing the TISes as a service from the core layer to the netdev layer
reduces the number of replecated TIS objects (in case of multiple
netdevs), and will ease the transition to netdev with multiple mdevs.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
TLS TISes are created using their own dedicated functions,
don't honor their specific logic here.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Introduce an API to set/unset the TX flow table root for a device.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Introduce an API to set/unset the L2TABLE entry silent mode for a
device. If silent, no north/south traffic is allowed, the device won't
be able to communicate with the port directly to send/receive traffic by
its own.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
MPIR register allows to query the PCIe indexes
and Socket-Direct related parameters.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Multiple device caps and features are required to support
single netdev Socket-Direct.
Add them here in preparation for the feature implementation.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Per display-timings.yaml, the 'timing' pattern should be used to
describe the display timings.
Change it accordingly to fix the following dt-schema warning:
imx27-apf27dev.dtb: display-timings: '800x480' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/panel/display-timings.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DP83TG720S-Q1 device is an IEEE 802.3bp and Open Alliance compliant
automotive Ethernet physical layer transceiver.
This driver was tested with i.MX8MP EQOS (stmmac) on the MAC side and
same TI PHY on other side.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20231212054144.87527-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move part of the genphy_c45_pma_read_abilities() code to a separate
function.
Some PHYs do not implement PMA/PMD status 2 register (Register 1.8) but
do implement PMA/PMD extended ability register (Register 1.11). To make
use of it, we need to be able to access this part of code separately.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20231212054144.87527-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We need to do signed arithmetic if we expect condition
`if (bytes < 0)` to be possible
Found by Linux Verification Center (linuxtesting.org) with SVACE
Fixes: 06a8fc7836 ("VSOCK: Introduce virtio_vsock_common.ko")
Signed-off-by: Nikolay Kuratov <kniv@yandex-team.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20231211162317.4116625-1-kniv@yandex-team.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pedro Tammela says:
====================
net/sched: optimizations around action binding and init
Scaling optimizations for action binding in rtnl-less filters.
We saw a noticeable lock contention around idrinfo->lock when
testing in a 56 core system, which disappeared after the patches.
====================
Link: https://lore.kernel.org/r/20231211181807.96028-1-pctammela@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tcf_idr_insert_many will replace the allocated -EBUSY pointer in
tcf_idr_check_alloc with the real action pointer, exposing it
to all operations. This operation is only needed when the action pointer
is created (ACT_P_CREATED). For actions which are bound to (returned 0),
the pointer already resides in the idr making such operation a nop.
Even though it's a nop, it's still not a cheap operation as internally
the idr code walks the idr and then does a replace on the appropriate slot.
So if the action was bound, better skip the idr replace entirely.
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Link: https://lore.kernel.org/r/20231211181807.96028-3-pctammela@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of relying only on the idrinfo->lock mutex for
bind/alloc logic, rely on a combination of rcu + mutex + atomics
to better scale the case where multiple rtnl-less filters are
binding to the same action object.
Action binding happens when an action index is specified explicitly and
an action exists which such index exists. Example:
tc actions add action drop index 1
tc filter add ... matchall action drop index 1
tc filter add ... matchall action drop index 1
tc filter add ... matchall action drop index 1
tc filter ls ...
filter protocol all pref 49150 matchall chain 0 filter protocol all pref 49150 matchall chain 0 handle 0x1
not_in_hw
action order 1: gact action drop
random type none pass val 0
index 1 ref 4 bind 3
filter protocol all pref 49151 matchall chain 0 filter protocol all pref 49151 matchall chain 0 handle 0x1
not_in_hw
action order 1: gact action drop
random type none pass val 0
index 1 ref 4 bind 3
filter protocol all pref 49152 matchall chain 0 filter protocol all pref 49152 matchall chain 0 handle 0x1
not_in_hw
action order 1: gact action drop
random type none pass val 0
index 1 ref 4 bind 3
When no index is specified, as before, grab the mutex and allocate
in the idr the next available id. In this version, as opposed to before,
it's simplified to store the -EBUSY pointer instead of the previous
alloc + replace combination.
When an index is specified, rely on rcu to find if there's an object in
such index. If there's none, fallback to the above, serializing on the
mutex and reserving the specified id. If there's one, it can be an -EBUSY
pointer, in which case we just try again until it's an action, or an action.
Given the rcu guarantees, the action found could be dead and therefore
we need to bump the refcount if it's not 0, handling the case it's
in fact 0.
As bind and the action refcount are already atomics, these increments can
happen without the mutex protection while many tcf_idr_check_alloc race
to bind to the same action instance.
In case binding encounters a parallel delete or add, it will return
-EAGAIN in order to try again. Both filter and action apis already
have the retry machinery in-place. In case it's an unlocked filter it
retries under the rtnl lock.
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Link: https://lore.kernel.org/r/20231211181807.96028-2-pctammela@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Per imx-iim.yaml, the compatible string should only contain a single
entry.
Use it as "fsl,imx25-iim" to fix the following dt-schema warning:
imx25-karo-tx25.dtb: efuse@53ff0000: compatible: ['fsl,imx25-iim', 'fsl,imx27-iim'] is too long
from schema $id: http://devicetree.org/schemas/nvmem/imx-iim.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
snprintf returns the length of the formatted string, excluding the trailing
null, without accounting for truncation. This means that is the return
value is greater than or equal to the size parameter, the fw_version string
was truncated.
Link: https://docs.kernel.org/core-api/kernel-api.html#c.snprintf
Fixes: 1b2bd0c026 ("net/mlx5e: Check return value of snprintf writing to fw_version buffer for representors")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
snprintf returns the length of the formatted string, excluding the trailing
null, without accounting for truncation. This means that is the return
value is greater than or equal to the size parameter, the fw_version string
was truncated.
Reported-by: David Laight <David.Laight@ACULAB.COM>
Closes: https://lore.kernel.org/netdev/81cae734ee1b4cde9b380a9a31006c1a@AcuMS.aculab.com/
Link: https://docs.kernel.org/core-api/kernel-api.html#c.snprintf
Fixes: 41e63c2baa ("net/mlx5e: Check return value of snprintf writing to fw_version buffer")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Set the error code if set_branch_dest_ft() fails.
Fixes: ccbe33003b ("net/mlx5e: TC, Don't offload post action rule if not supported")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Preserve the error code if esw_add_restore_rule() fails. Don't return
success.
Fixes: 6702782845 ("net/mlx5e: TC, Set CT miss to the specific ct action instance")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
While handling new traces, to verify it is not the first block being
written, last_timestamp is checked. But instead of checking it is non
zero it is verified to be zero. Fix to verify last_timestamp is not
zero.
Fixes: c71ad41ccb ("net/mlx5: FW tracer, events handling")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Feras Daoud <ferasda@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
XDP transmits fragmented packets that are larger than MTU size instead of
dropping those packets. The drop check that checks whether a packet is larger
than MTU is comparing MTU size against the linear part length only.
Adjust the drop check to compare MTU size against both linear and non-linear
part lengths to avoid transmitting fragmented packets larger than MTU size.
Fixes: 39a1665d16 ("net/mlx5e: Implement sending multi buffer XDP frames")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The cited commit increases num_block_tc when unblock tc offload.
Actually should decrease it.
Fixes: c8e350e62f ("net/mlx5e: Make TC and IPsec offloads mutually exclusive on a netdev")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Coverity Scan reports the following issue. But it's impossible that
mlx5_get_dev_index returns 7 for PF, even if the index is calculated
from PCI FUNC ID. So add the checking to make coverity slience.
CID 610894 (#2 of 2): Out-of-bounds write (OVERRUN)
Overrunning array esw->fdb_table.offloads.peer_miss_rules of 4 8-byte
elements at element index 7 (byte offset 63) using index
mlx5_get_dev_index(peer_dev) (which evaluates to 7).
Fixes: 9bee385a6e ("net/mlx5: E-switch, refactor FDB miss rule add/remove")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When kcalloc() for ft->g succeeds but kvzalloc() for in fails,
fs_udp_create_groups() will free ft->g. However, its caller
fs_udp_create_table() will free ft->g again through calling
mlx5e_destroy_flow_table(), which will lead to a double-free.
Fix this by setting ft->g to NULL in fs_udp_create_groups().
Fixes: 1c80bd6843 ("net/mlx5e: Introduce Flow Steering UDP API")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Fix a cmd->ent use after free due to a race on command entry.
Such race occurs when one of the commands releases its last refcount and
frees its index and entry while another process running command flush
flow takes refcount to this command entry. The process which handles
commands flush may see this command as needed to be flushed if the other
process allocated a ent->idx but didn't set ent to cmd->ent_arr in
cmd_work_handler(). Fix it by moving the assignment of cmd->ent_arr into
the spin lock.
[70013.081955] BUG: KASAN: use-after-free in mlx5_cmd_trigger_completions+0x1e2/0x4c0 [mlx5_core]
[70013.081967] Write of size 4 at addr ffff88880b1510b4 by task kworker/26:1/1433361
[70013.081968]
[70013.082028] Workqueue: events aer_isr
[70013.082053] Call Trace:
[70013.082067] dump_stack+0x8b/0xbb
[70013.082086] print_address_description+0x6a/0x270
[70013.082102] kasan_report+0x179/0x2c0
[70013.082173] mlx5_cmd_trigger_completions+0x1e2/0x4c0 [mlx5_core]
[70013.082267] mlx5_cmd_flush+0x80/0x180 [mlx5_core]
[70013.082304] mlx5_enter_error_state+0x106/0x1d0 [mlx5_core]
[70013.082338] mlx5_try_fast_unload+0x2ea/0x4d0 [mlx5_core]
[70013.082377] remove_one+0x200/0x2b0 [mlx5_core]
[70013.082409] pci_device_remove+0xf3/0x280
[70013.082439] device_release_driver_internal+0x1c3/0x470
[70013.082453] pci_stop_bus_device+0x109/0x160
[70013.082468] pci_stop_and_remove_bus_device+0xe/0x20
[70013.082485] pcie_do_fatal_recovery+0x167/0x550
[70013.082493] aer_isr+0x7d2/0x960
[70013.082543] process_one_work+0x65f/0x12d0
[70013.082556] worker_thread+0x87/0xb50
[70013.082571] kthread+0x2e9/0x3a0
[70013.082592] ret_from_fork+0x1f/0x40
The logical relationship of this error is as follows:
aer_recover_work | ent->work
-------------------------------------------+------------------------------
aer_recover_work_func |
|- pcie_do_recovery |
|- report_error_detected |
|- mlx5_pci_err_detected |cmd_work_handler
|- mlx5_enter_error_state | |- cmd_alloc_index
|- enter_error_state | |- lock cmd->alloc_lock
|- mlx5_cmd_flush | |- clear_bit
|- mlx5_cmd_trigger_completions| |- unlock cmd->alloc_lock
|- lock cmd->alloc_lock |
|- vector = ~dev->cmd.vars.bitmask
|- for_each_set_bit |
|- cmd_ent_get(cmd->ent_arr[i]) (UAF)
|- unlock cmd->alloc_lock | |- cmd->ent_arr[ent->idx]=ent
The cmd->ent_arr[ent->idx] assignment and the bit clearing are not
protected by the cmd->alloc_lock in cmd_work_handler().
Fixes: 50b2412b7e ("net/mlx5: Avoid possible free of command entry while timeout comp handler")
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Shifeng Li <lishifeng@sangfor.com.cn>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Cited commit introduced potential double free since encap_header can be
destroyed twice in some cases - once by error cleanup sequence in
mlx5e_tc_tun_{create|update}_header_ipv{4|6}(), once by generic
mlx5e_encap_put() that user calls as a result of getting an error from
tunnel create|update. At the same time the point where e->encap_header is
assigned can't be delayed because the function can still return non-error
code 0 as a result of checking for NUD_VALID flag, which will cause
neighbor update to dereference NULL encap_header.
Fix the issue by:
- Nulling local encap_header variables in
mlx5e_tc_tun_{create|update}_header_ipv{4|6}() to make kfree(encap_header)
call in error cleanup sequence noop after that point.
- Assigning reformat_params.data from e->encap_header instead of local
variable encap_header that was set to NULL pointer by previous step. Also
assign reformat_params.size from e->encap_size for uniformity and in order
to make the code less error-prone in the future.
Fixes: d589e785ba ("net/mlx5e: Allow concurrent creation of encap entries")
Reported-by: Dust Li <dust.li@linux.alibaba.com>
Reported-by: Cruz Zhao <cruzzhao@linux.alibaba.com>
Reported-by: Tianchen Ding <dtcccc@linux.alibaba.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This reverts commit 6f9b1a0731.
This patch is causing a null ptr issue, the proper fix is in the next
patch.
Fixes: 6f9b1a0731 ("net/mlx5e: fix double free of encap_header")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This reverts commit 3a4aa3cb83.
This patch is causing a null ptr issue, the proper fix is in the next
patch.
Fixes: 3a4aa3cb83 ("net/mlx5e: fix double free of encap_header in update funcs")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Since commit 638e4b825d ("bpf: Allows per-cpu maps and map-in-map in
sleepable programs"), sleepable BPF program can also use map-in-map, but
maybe_wait_bpf_programs() doesn't handle it accordingly. The main reason
is that using synchronize_rcu_tasks_trace() to wait for the completions
of these sleepable BPF programs may incur a very long delay and
userspace may think it is hung, so the wait for sleepable BPF programs
is skipped. Update the comments in maybe_wait_bpf_programs() to reflect
the reason.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/20231211083447.1921178-1-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
security_path_* based LSM hooks appear to be generally missing from
the sleepable_lsm_hooks list. Initially add a small subset of them to
the preexisting sleepable_lsm_hooks list so that sleepable BPF helpers
like bpf_d_path() can be used from sleepable BPF LSM based programs.
The security_path_* hooks added in this patch are similar to the
security_inode_* counterparts that already exist in the
sleepable_lsm_hooks list, and are called in roughly similar points and
contexts. Presumably, making them OK to be also annotated as
sleepable.
Building a kernel with DEBUG_ATOMIC_SLEEP options enabled and running
reasonable workloads stimulating activity that would be intercepted by
such security hooks didn't show any splats.
Notably, I haven't added all the security_path_* LSM hooks that are
available as I don't need them at this point in time.
Signed-off-by: Matt Bobrowski <mattbobrowski@google.com>
Acked-by: KP Singh <kpsingh@kernel.org>
Link: https://lore.kernel.org/r/ZXM3IHHXpNY9y82a@google.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
John Fastabend says:
====================
Eric reported a syzbot splat from a null ptr deref from recent fix to
resolve a use-after-free with af-unix stream sockets and BPF sockmap
usage.
The issue is I missed is we allow unconnected af_unix STREAM sockets to
be added to the sockmap. Fix this by blocking unconnected sockets.
v2: change sk_is_unix to sk_is_stream_unix (Eric) and remove duplicate
ASSERTS in selftests the xsocket helper already marks FAIL (Jakub)
====================
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Add test to sockmap_basic to ensure af_unix sockets that are not connected
can not be added to the map. Ensure we keep DGRAM sockets working however
as these will not be connected typically.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/r/20231201180139.328529-3-john.fastabend@gmail.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>