No functional changes here, just to prepare for next patch.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
UBI has changed the MTD_UBI_BEB_LIMIT semantics. It used to be a percent of
total amount of eraseblock in the partition, and now it is the maximum
amount of bad eraseblocks on the entire devise per 1024 eraseblocks. So not
only the units changed, but also the meaning.
Richard Genoud <richard.genoud@gmail.com> says:
"I found the board:
https://www.olimex.com/dev/sam9-L9260.html
and the nand datasheet:
http://www.rockbox.org/wiki/pub/Main/LyrePrototype/K9xxG08UXM.pdf
page 11, we can see that the max_bad_bebper1024 is 25 (100 for 4096)"
Thus, use "25" for sam9.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
On NAND flash devices, UBI reserves some physical erase blocks (PEB) for
bad block handling. Today, the number of reserved PEB can only be set as a
percentage of the total number of PEB in each MTD partition. For example, for a
NAND flash with 128KiB PEB, 2 MTD partition of 20MiB (mtd0) and 100MiB (mtd1)
and 2% reserved PEB:
- the UBI device on mtd0 will have 2 PEB reserved
- the UBI device on mtd1 will have 16 PEB reserved
The problem with this behaviour is that NAND flash manufacturers give a
minimum number of valid block (NVB) during the endurance life of the
device, e.g.:
Parameter Symbol Min Max Unit Notes
--------------------------------------------------------------
Valid block number NVB 1004 1024 Blocks 1
From this number we can deduce the maximum number of bad PEB that a device will
contain during its endurance life: a 128MiB NAND flash (1024 PEB) will not have
less than 20 bad blocks during the flash endurance life.
But the manufacturer doesn't tell where those bad block will appear. He doesn't
say either if they will be equally disposed on the whole device (and I'm pretty
sure they won't). So, according to the datasheets, we should reserve the
maximum number of bad PEB for each UBI device (worst case scenario: 20 bad
blocks appears on the smallest MTD partition).
So this patch make UBI use the whole MTD device size to calculate the maximum
bad expected eraseblocks.
The Kconfig option is in per1024 blocks, thus it can have a default value of 20
which is *very* common for NAND devices.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
'mtd_get_device_size()' returns the size of the whole MTD device, that is the
mtd_info master size. This will be used by UBI to calculate the maximum number
of bad blocks (MBB) on a MTD device.
Artem: amended the patch a bit.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
'struct mtd_info' is not modified by 'mtd_is_partition()' so it can be marked
as "const".
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
CONFIG_MTD_UBI_BEB_RESERVE has been removed and now we use
CONFIG_MTD_UBI_BEB_LIMIT instead.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
CONFIG_MTD_UBI_BEB_RESERVE and MIN_RESEVED_PEBS are no longer used,
since the amount of reserved eraseblocks for bad PEB handling is now
derived from 'ubi->bad_peb_limit' (ubi's maximum expected bad
eraseblocks).
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
The existing mechanism of reserving PEBs for bad PEB handling has two
flaws:
- It is calculated as a percentage of good PEBs instead of total PEBs.
- There's no limit on the amount of PEBs UBI reserves for future bad
eraseblock handling.
This patch changes the mechanism to overcome these flaws.
The desired level of PEBs reserved for bad PEB handling (beb_rsvd_level)
is set to the maximum expected bad eraseblocks (bad_peb_limit) minus the
existing number of bad eraseblocks (bad_peb_count).
The actual amount of PEBs reserved for bad PEB handling is usually set
to the desired level (but in some circumstances may be lower than the
desired level, e.g. when attaching to a device that has too few
available PEBs to satisfy the desired level).
In the case where the device has too many bad PEBs (above the expected
limit), then the desired level, and the actual amount of PEBs reserved
are set to zero. No PEBs will be set aside for future bad eraseblock
handling - even if some PEBs are made available (e.g. by shrinking a
volume).
If another PEB goes bad, and there are available PEBs, then the
eraseblock will be marked bad (consuming one available PEB). But if
there are no available PEBs, ubi will go into readonly mode.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Introduce 'ubi->bad_peb_limit', which specifies an upper limit of PEBs
UBI expects to go bad. Currently, it is initialized to a fixed percentage
of total PEBs in the UBI device (configurable via CONFIG_MTD_UBI_BEB_LIMIT).
The 'bad_peb_limit' is intended to be used for calculating the amount of PEBs
UBI needs to reserve for bad eraseblock handling.
Artem: minor amendments.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
We are going to kill the CONFIG_MTD_UBI_BEB_RESERVE configuration option soon
and use the CONFIG_MTD_UBI_BEB_LIMIT instead. In order to do this smoothly,
we now introduce the new configuration option to sam9_l9260_defconfig, and
will kill the old one after the corresponding UBI changes are done.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Use hash table to store ports of datapath. Allow 64K ports per switch.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
The vlan encapsulation fields in the maximum flow defintion were
never updated when the representation changed before upstreaming.
In theory this could cause a kernel panic when a maximum length
flow is used. In practice this has never happened (to my knowledge)
because skb allocations are padded out to a cache line so you would
need the right combination of flow and packet being sent to userspace.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Add a "C5" cpuidle state to the SH7372 SoC connected to the A4S power
domain in such a way that A4S may be turned off by cpuidle if all
I/O devices in that domain have been suspended (or do not have
attached drivers).
This requires some reorganization of the initialization of SH7372
power management which affects the the boards based on it, Mackerel
and AP4EVB.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The sh7372 cpuidle code uses the same artificially designed routine
shmobile_cpuidle_enter() as the .enter() callback for all of its
cpuidle states. However, shmobile_cpuidle_enter() calls a different
"enter" function for each state using an array of function pointers
populated by the sh7372 PM initialization code. Moreover, the
states[] array of the shmobile cpuidle driver is populated by that
code as well, although in principle it just might have been filled
with static data.
All of that complexity goes away if the sh7372 cpuidle code is
allowed to define its own cpuidle driver structure that can be passed
for registration to the common shmobile cpuidle initialization
routine, so modify the code accordingly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The role of the only function in the common.c file in
arch/arm/mach-shmobile, shmobile_init_late(), is to call two
initializers whose definitions depend on kernel configuration
options. Those initializers may very well be called from a static
inline function in arm/mach-shmobile/include/mach/common.h,
though, in which makes the code a bit easier to read. Moreover,
the common.c may be dropped entirely then.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The !console_suspend_enabled check in sh7372_enter_suspend() seems
to be reversed and the condition it is supposed to catch (console
clock enabled) should be detected by the sh7372_sysc_valid() check
anyway, so remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Use the function rmobile_add_devices_to_domains() introduced
previously for adding devices to PM domains during the AP4EVB
initialization instead of a series of rmobile_add_device_to_domain*()
calls. This also causes the default device PM QoS latencies to be
used on that board in analogy with Mackerel.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
On SH7372 and Mackerel devices are added to PM domains through a
series of rmobile_add_device_to_domain_td() calls where the last
argument is always the same. This is quite inefficient, so add
a common function for adding devices to PM domains that reads the
domain-device pairs information from a table and use it during SH7372
and Mackerel initialization.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The results of adaptive latency computations in
GENPD_DEV_TIMED_CALLBACK() show that the start/stop and save/restore
state latencies of all devices on the Mackerel board I have tried are
a little below 250 us. Therefore, if the 250 us is used as the
common initial value of the latency fields in struct gpd_timing_data
for all devices on Mackerel, the latency values will never have to
change at run time and there won't be any overhead related to
re-computation of the corresponding PM QoS data.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The results of adaptive latency computations in
GENPD_DEV_TIMED_CALLBACK() show that the start/stop and save/restore
state latencies of all devices on SH7372 I have tried are a little
below 250 us. Therefore, if the 250 us is used as the common initial
value of the latency fields in struct gpd_timing_data for all devices
on SH7372, the latency values will never have to change at run time
and there won't be any overhead related to re-computation of the
corresponding PM QoS data.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Make it possible to specify device start/stop and save/restore
state latencies directy when adding devices to PM domains. For
this purpose, introduce rmobile_add_device_to_domain_td() whose
third argument is a pointer to a struct gpd_timing_data object
containing device latency data.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The results of adaptive latency computations in __pm_genpd_poweron()
and pm_genpd_poweroff() show that the power on/power off latencies
of all power domains in SH7372 are a little below 250 us. Therefore,
if 250 us is used as the common initial value of the latency fields
in struct generic_pm_domain for all domains, the latency values
will never have to change at run time and there won't be any overhead
related to re-computation of the corresponding PM QoS data.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Since rmobile_init_pm_domain() is not called anywhere outside of
arch/arm/mach-shmobile/pm-rmobile.c any more, it can be made static
and its header may be removed from pm-rmobile.h. Modify the code
accordingly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Instead of giving a name to every r8a7779's PM domain object, put
them all into a table and initialize them all together in a loop.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Instead of giving a name to every r8a7740's PM domain object, put
them all into a table and use rmobile_init_domains(), introduced by a
previous patch, for initializing them all altogether. Also, use
pm_genpd_add_subdomain_names() for adding A3SP as a subdomain of A4S.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Instead of giving a name to every sh7372's PM domain object, put them
all into a table and use rmobile_init_domains(), introduced by a
previous patch, for initializing them all altogether. Also, use
pm_genpd_add_subdomain_names() for adding subdomains to the PM
domains and pm_genpd_poweron_name() for turning on the A4S domain
when preparing for system suspend.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The sh7372_enter_suspend() routine checks the status field of the
generic PM domain object corresponding to the A4S domain in order to
check if it can turn that domain off when entering system sleep.
However, it shouldn't rely on the specific values of the generic
data structures this way, so make it use its own mechanism to
recognize when it is safe to turn that domain off.
For this purpos, introduce a boolean variable a4s_suspend_ready
that will be set by the A4S' suspend routine and unset by its
resume routine executed by rmobile_pd_power_down() and
__rmobile_pd_power_up(), respectively.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Add a new routine, rmobile_init_domains(), allowing the caller
to initialize all generic PM objects stored in a table in one
operation.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Make the power management code under arch/arm/mach-shmobile/
use pm_genpd_add_subdomain_names() for adding subdomains to power
domains, which makes it possible to drop
rmobile_pm_add_subdomain() and will allow us to carry out those
operations for domain objects stored in tables in a straightforward
way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
If the r8a7779's PM domains are given names, this SoC and its boards
will be able to use rmobile_add_device_to_domain() for adding devices
to those domains and r8a7779_add_device_to_domain(), which is not
used anywhere at the moment anyway, may be dopped.
Accordingly, give names to the r8a7779's PM domains and drop
r8a7779_add_device_to_domain().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Make the power management code under arch/arm/mach-shmobile/ use
names of power domains instead of pointers to domain objects for
adding devices to the domains. This will allow us to put the
domain objects into tables and register them all in one shot
going forward.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
This change initialises the cpu id field of cs_cpu_dbs_info structure in
conservative governor and keep this consistent with other governors.
Similar initialisation is present in ondemand governor.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Make it possible to use domain names in operations connecting cpuidle
to and disconnecting it from a PM domain. This is useful on
platforms where PM domain objects are organized in such a way that
the names of the domains are easier to use than the addresses of
those objects.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The names of the cpuidle-related functions in
drivers/base/power/domain.c are inconsistent with the names of the
other exported functions in that file (the "pm_" prefix is missing
from them) and they are missing kerneldoc comments.
Fix that by adding the missing "pm_" prefix to the names of those
functions and add kerneldoc comments documenting them.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
It sometimes is necessary to turn on a given PM domain when only
the name of it is known and the domain pointer is not readily
available. For this reason, add a new helper function,
pm_genpd_name_poweron(), allowing the caller to turn on a PM domain
using its name for identification. To avoid code duplication,
move the domain lookup code to a separate function.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add a new helper function, pm_genpd_add_subdomain_names(), allowing
the caller to add a subdomain to a generic PM domain using names for
domain identification (both domains have to be initialized before).
This function is useful for adding subdomains to PM domains whose
representations are stored in tables, when the caller doesn't know
the indices of the domain to add the subdomain to and of the
subdomain itself, but it knows the domains' names.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add a new helper function __pm_genpd_name_add_device() allowing
a device to be added to a (registered) generic PM domain identified
by name. Add a wrapper around it, pm_genpd_name_add_device(),
passing NULL as the last argument and reorganize pm_domains.h for the
new functions to be defined consistently with the existing ones.
These functions are useful for adding devices to PM domains whose
representations are stored in tables, when the caller doesn't know
the index of the domain to add the device to, but it knows the
domain's name.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The syscore device PM flag used to mark the devices (belonging to
PM domains) that should never be turned off, except for the system
core (syscore) suspend/hibernation and resume stages, need not be
accessed by the runtime PM core functions, because all of the devices
it is set for need to be marked as "irq safe" anyway and are
protected from being turned off by runtime PM by ensuring that their
usage counters are always set.
For this reason, make the syscore flag system-wide PM-specific
and simplify the code used for manipulating it, because it need not
acquire the device's power.lock any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Modify the SH MTU2 clock event device driver to support runtime PM at
a basic level (i.e. device clocks can be disabled and enabled, but
domain power must be on, because the device has to be marked as
"irq safe").
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Modify the SH CMT clock source/clock event device driver to support
runtime PM at a basic level (i.e. device clocks can be disabled and
enabled, but domain power must be on, because the devices have to
be marked as "irq safe").
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Modify the SH TMU clock source/clock event device driver to support
runtime PM at a basic level (i.e. device clocks can be disabled and
enabled, but domain power must be on, because the devices have to
be marked as "irq safe").
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The genpd_start_dev() routine used by pm_genpd_runtime_resume()
to put "irq safe" devices into the full power state measures the
time necessary to "start" the device and updates its PM QoS timing
data if necessary. This may lead to a deadlock if the given device
is a clock source and genpd_start_dev() is invoked from within the
clock source's .enable() routine, which will happen if that routine
uses pm_runtime_get_sync(), for example, to ensure that the device
is operational.
For this reason, introduce a special routine analogous to
genpd_start_dev(), called genpd_start_dev_no_timing(), that doesn't
carry out the time measurement, and make pm_genpd_runtime_resume()
use it instead of genpd_start_dev() to power up "irq safe" devices.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The syscore device PM flag is used to mark the devices (belonging to
a PM domain) that should never be turned off, except for the system
core (syscore) suspend/hibernation and resume stages. That flag is
stored in the device's struct pm_subsys_data object whose address is
available from struct device. However, in some situations it may be
convenient to set that flag before the device is added to a PM
domain, so it is better to move it directly to the "power" member of
struct device. Then, it can be checked by the routines in
drivers/base/power/runtime.c and drivers/base/power/main.c, which is
more straightforward.
This also reduces the number of dev_gpd_data() invocations in the
generic PM domains framework, so the overhead related to the syscore
flag is slightly smaller.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The always_on device flag is used to mark the devices (belonging to
a PM domain) that should never be turned off, except for the system
core (syscore) suspend/hibernation and resume stages. Change name
of that flag to "syscore" to better reflect its purpose.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Runtime PM helper functions, like pm_runtime_get_sync(), cannot be
called by early platform device drivers, because the devices' power
management locks are not initialized at that time. This is quite
inconvenient, so modify early_platform_add_devices() to initialize
the devices power management locks as appropriate and make sure that
they won't be initialized more than once if an early platform
device is going to be used as a regular one later.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Make the device power management initialization more straightforward
by moving the initialization of common (i.e. used by both runtime PM
and system suspend) fields to a separate routine.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
