The regulators should be tending to the maximum in the available range and
consumers should specify the widest range possible.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
MAX77686_REGULATORS is known in compile time.
Use array to save pointer to rdev makes the code simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Initialize config.of_node for regulator before registering.
This is needed for DT based regulator support.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To set REGULATOR_MODE_IDLE mode, what we do is to clear DC1_ACTIVE and
DC1_SLEEP bits, this can be done in one wm8400_set_bits() call.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
wm831x_reg_read() returns negative error code on failure.
This prevents using the error code as the value read.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We already know the mask in lp8788_init_dvs() function, and we can update
the corresponding bit for default_dvs_mode in lp8788_init_dvs() function.
This function looks not necessary to me.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Tested-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For fixed voltage, the n_voltages should be 1 rather than 0.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use mc13xxx_reg_rmw rather than a mc13xxx_reg_read and a mc13xxx_reg_write calls.
This logic to set MC13892_SWITCHERS0_SWxHI bit is pretty simple:
if (volt > 1375000)
set MC13892_SWITCHERS0_SWxHI bit
else if (volt < 1100000)
clear MC13892_SWITCHERS0_SWxHI bit
else
leave MC13892_SWITCHERS0_SWxHI bit untouched
We already know the selector, so we don't need to calculate the selector again.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Then we can remove lock/unlock around the caller.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Then we can remove lock/unlock around the caller.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The voltage selection logic is supposed to find the samllest voltage falls
within specified range. When using equation to calculate vsel, we need to
ensure the requested min_uV meet the range of using the equation.
Otherwise we may select a voltage that is out of specified range.
For example, in the case vsel = 62 means select voltage of 2100000uV.
What we want is to ensure the requested min_uV <= 2100000 rather than checking
max_uV >= 2100000. And this also means in the case min_uV > 2100000, vsel = 62
does not meet the request.
Also calling twl6030smps_list_voltage() for all cases to ensure the selected
voltage still in bounds.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This was missing until now and the underlying
_regulator_do_set_voltage is using this value when calling list_voltage.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The number of regulator is known at compile time, use array to save pointer to
rdev makes the code simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
v2: Fixed result still wrong in the case of 512 KiB DRAM. Oops.
Applicable to 3.5.3 mainline.
In emu8000.c, size_dram determines the amount of memory on the sound card by
doing write/readback tests starting at 512 KiB and incrementing by 512 KiB.
On success, detected_size is updated to the successful address and testing
continues. On failure, the loop is immediately exited. The resulting
detected_size is 512 KiB too small except in two special cases:
1. If there is no memory, the initial 0 value of detected_size is used, which
is correct.
2. If the address space wraps around, detected_size is updated before the
bailout, so the result is correct.
The patch corrects all cases and was tested with an AWE64 Gold. Before:
EMU8000 [0x620]: 3584 Kb on-board memory detected
asfxload 4GMGSMT.SF2 (4174814 B) fails.
After:
EMU8000 [0x620]: 4096 Kb on-board memory detected
asfxload 4GMGSMT.SF2 succeeds.
I do not have a card with 512 KiB to test with, but by forcibly enabling the
added conditional I verified on the AWE64 Gold that it detects 512 KiB
(successfully reading from the first memory location) and does not hang the
card.
C.f. Bug 46451 https://bugzilla.kernel.org/show_bug.cgi?id=46451
Signed-off-by: David Flater <dave@flaterco.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch is to rename the directory "ep93xx" in "cirrus".
Name more accurately reflects the manufacturer and allows to add
drivers not only for architecture ep93xx in this directory.
Patch not contain any functional changes.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All SAMSUNG ASoC needs SND_SOC_SAMSUNG configuration.
This patch change Kconfig to support all SAMSUNG ASoC.
Signed-off-by: Sangsu Park <sangsu4u.park@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Both the schematics and practical testing show that the HP detect GPIO
is high when the headphones are plugged in. Hence, the snd_soc_jack_gpio
should not specify to invert the signal.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <stable@vger.kernel.org> # v3.4 v3.5
Include linux/io.h for raw io operations in atmel-scc header.
This fixes the following build error:
CC [M] sound/soc/atmel/atmel_ssc_dai.o
sound/soc/atmel/atmel_ssc_dai.c: In function 'atmel_ssc_interrupt':
sound/soc/atmel/atmel_ssc_dai.c:171: error: implicit declaration of function '__raw_readl'
sound/soc/atmel/atmel_ssc_dai.c: In function 'atmel_ssc_shutdown':
sound/soc/atmel/atmel_ssc_dai.c:249: error: implicit declaration of function '__raw_writel'
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These codecs seem reporting EPSS but require longer delay for the
proper D3 transition. For example, D3_STOP_CLOCK_OK bit won't be set
correctly even after D3.
In this patch, codec->epss flag is overridden for avoid the
misbehavior.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EPSS parameter should be static, so we can read it once and remember.
This also allows more easily to override the wrong EPSS capability
reported from a codec by changing the flag in the codec
initialization step.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Nobody does set_orig_insn(verify => false), and I think nobody will.
Remove this argument. IIUC set_orig_insn(verify => false) was needed
to single-step without xol area.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Now that we have uprobe_dup_mmap() we can fold uprobe_reset_state()
into the new hook and remove it. mmput()->uprobe_clear_state() can't
be called before dup_mmap().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Add the new MMF_HAS_UPROBES flag. It is set by install_breakpoint()
and it is copied by dup_mmap(), uprobe_pre_sstep_notifier() checks
it to avoid the slow path if the task was never probed. Perhaps it
makes sense to check it in valid_vma(is_register => false) as well.
This needs the new dup_mmap()->uprobe_dup_mmap() hook. We can't use
uprobe_reset_state() or put MMF_HAS_UPROBES into MMF_INIT_MASK, we
need oldmm->mmap_sem to avoid the race with uprobe_register() or
mmap() from another thread.
Currently we never clear this bit, it can be false-positive after
uprobe_unregister() or uprobe_munmap() or if dup_mmap() hits the
probed VM_DONTCOPY vma. But this is fine correctness-wise and has
no effect unless the task hits the non-uprobe breakpoint.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
-EEXIST from install_breakpoint() no longer makes sense, all
callers should simply treat it as "success". Change the code
to return zero and simplify register_for_each_vma().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Once install_breakpoint() fails uprobe_mmap() "ignores" all other
uprobes and returns the error.
It was never really needed to to stop after the first error, and
in fact it was always wrong at least in -ENOTSUPP case.
Change uprobe_mmap() to ignore the errors and always return 0.
This is not what we want in the long term, but until we teach
the callers to handle the failure it would be better to remove
the pointless complications. And this doesn't look too bad, the
only "reasonable" error is ENOMEM but in this case the caller
should be oom-killed in the likely case or the system has more
serious problems.
However it makes sense to stop if fatal_signal_pending() == T.
In particular this helps if the task was oom-killed.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
1. Kill dup_mmap()->uprobe_mmap(), it was only needed to calculate
new_mm->uprobes_state.count removed by the previous patch.
If the forking process has a pending uprobe (int3) in vma, it will
be copied by copy_page_range(), note that it checks vma->anon_vma
so "Don't copy ptes" is not possible after install_breakpoint()
which does anon_vma_prepare().
2. Remove is_swbp_at_addr() and "int count" in uprobe_mmap(). Again,
this was needed for uprobes_state.count.
As a side effect this fixes the bug pointed out by Srikar,
this code lacked the necessary put_uprobe().
3. uprobe_munmap() becomes a nop after the previous patch. Remove the
meaningless code but do not remove the helper, we will need it.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
uprobes_state->count is only needed to avoid the slow path in
uprobe_pre_sstep_notifier(). It is also checked in uprobe_munmap()
but ironically its only goal to decrement this counter. However,
it is very broken. Just some examples:
- uprobe_mmap() can race with uprobe_unregister() and wrongly
increment the counter if it hits the non-uprobe "int3". Note
that install_breakpoint() checks ->consumers first and returns
-EEXIST if it is NULL.
"atomic_sub() if error" in uprobe_mmap() looks obviously wrong
too.
- uprobe_munmap() can race with uprobe_register() and wrongly
decrement the counter by the same reason.
- Suppose an appication tries to increase the mmapped area via
sys_mremap(). vma_adjust() does uprobe_munmap(whole_vma) first,
this can nullify the counter temporarily and race with another
thread which can hit the bp, the application will be killed by
SIGTRAP.
- Suppose an application mmaps 2 consecutive areas in the same file
and one (or both) of these areas has uprobes. In the likely case
mmap_region()->vma_merge() suceeds. Like above, this leads to
uprobe_munmap/uprobe_mmap from vma_merge()->vma_adjust() but then
mmap_region() does another uprobe_mmap(resulting_vma) and doubles
the counter.
This patch only removes this counter and fixes the compile errors,
then we will try to cleanup the changed code and add something else
instead.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
by the time we get here (after we pass cleanup_ret) uprobe is always is
set. If it is NULL we leave very early in the code.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Since read_opcode() reads from the referenced page and doesnt modify
the page contents nor the page attributes, there is no need to lock
the page.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Use unsigned int to make clear that the codes required only for
modules will be reduced by the compiler optimization.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no more users of s3c2410_gpio_pullup(), s3c2410_gpio_setpin()
and s3c2410_gpio_getpin() so remove theese functions.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
It's safe to empty the plat-samsung/incude/plat/gpio-fns.h header
now when all users of those functions have been converted to
generic gpiolib API or to s3c_gpio_cfg().
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is a prerequisite for removal of deprecated s3c2410_gpio* API
from the Samsung gpiolib driver.
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Guillaume Gourat <guillaume.gourat@nexvision.tv>
Cc: Michel Pollet <buserror@gmail.com>
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Support for ESNs (extended sequence numbers).
Tested with strongswan on a P2020RDB back-to-back setup.
Extracted from /etc/ipsec.conf:
esp=aes-sha1-esn-modp4096!
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Generate a link table in case assoc data is a scatterlist.
While at it, add support for handling non-contiguous assoc data and iv.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
It's more natural to think of these vars as bool rather than int.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
talitos_edesc_alloc does not need hash_result param.
Checking whether dst scatterlist is NULL or not is all that is required.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
