If the regulator doesn't supply a way of reading back the voltage but does
provide a list_voltage() operation then use that with a selector of zero
to read the voltage. Regulators doing this means that we have the list
operation there for consumers that want to configure themselves.
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On Intel systems corrected machine check interrupts (CMCI) may be sent to
multiple logical processors; possibly to all processors on the affected
socket (SDM Volume 3B "15.5.1 CMCI Local APIC Interface"). This means
that a persistent error (such as a stuck bit in ECC memory) may cause
a storm of interrupts that greatly hinders or prevents forward progress
(probably on many processors).
To solve this we keep track of the rate at which each processor sees
CMCI. If we exceed a threshold, we disable CMCI delivery and switch to
polling the machine check banks. If the storm subsides (none of the
affected processors see any more errors for a complete poll interval) we
re-enable CMCI.
[Tony: Added console messages when storm begins/ends and increased storm
threshold from 5 to 15 so we have a few more logged entries before we
disable interrupts and start dropping reports]
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The Wolfson Bells board takes submodules for various audio functions but
since the system integrations are virtually identical for most of them we
can support the overwhemling majority from the same machine driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Arizona devices support two output system clocks. Provide support for
configuring these via set_sysclk(). Once the clock API is more useful
we should migrate over to that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we fail to register the card we should say why somewhere else so there's
no point in repeating the same thing with less information.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the past when ASoC had a custom probe deferral mechanism people
complained about the logspam it generated and didn't want to know about
the fact that we were doing probe deferral so all the error messages for
it were at dev_dbg(), making diagnostics hard. Now that we have probe
deferral as an accepted thing and it's generating log messages anyway
there's no need to worry about this so upgrade the severity of all the
probe deferral sources to dev_err() so that they are displayed by default.
Also add one for missing aux_devs since there wasn't one.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
cmci_discover() works out which machine check banks support CMCI, and
which of those are shared by multiple logical processors. It uses this
information to ensure that exactly one cpu is designated the owner of
each bank so that when interrupts are broadcast to multiple cpus, only one
of them will look in a shared bank to log the error and clear the bank.
At boot time cmci_discover() performs this task silently. But during
certain cpu hotplug operations it prints out a set of summary lines
like this:
CPU 35 MCA banks CMCI:0 CMCI:1 CMCI:3 CMCI:5 CMCI:6 CMCI:7 CMCI:8 CMCI:9 CMCI:10 CMCI:11
CPU 1 MCA banks CMCI:0 CMCI:1 CMCI:3
CPU 39 MCA banks CMCI:0 CMCI:1 CMCI:3
CPU 38 MCA banks CMCI:0 CMCI:1 CMCI:3
CPU 32 MCA banks CMCI:0 CMCI:1 CMCI:3
CPU 37 MCA banks CMCI:0 CMCI:1 CMCI:3
CPU 36 MCA banks CMCI:0 CMCI:1 CMCI:3
CPU 34 MCA banks CMCI:0 CMCI:1 CMCI:3
The value of these messages seems very low. A user might painstakingly
cross-check against the data sheet for a processor to ensure that all
CMCI supported banks are correctly reported, but this seems improbable.
If users really wanted to do this, we should print the information at
boot time too.
Remove the messages.
Signed-off-by: Tony Luck <tony.luck@intel.com>
If CONFIG options required for perf-lock are not enabled then the
corresponding tracepoints will not be enabled. Currently, the message to
the user is:
$ perf lock record -a -- sleep 1
invalid or unsupported event: 'lock:lock_acquire'
Run 'perf list' for a list of valid events
Improve the message with a suggestion on which CONFIG options are needed:
$ perf lock record -a -- sleep 1
tracepoint lock:lock_acquire is not enabled. Are CONFIG_LOCKDEP and CONFIG_LOCK_STAT enabled?
Suggested-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1344530137-25521-1-git-send-email-dsahern@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Hi Greg,
Here's four patches for 3.6. Most are marked for stable as well.
The first one makes the xHCI driver load properly on newer Rensas hosts.
The next two fix issues with the Etron host incorrectly marking short
transfers as successful, and avoiding log warning spam for hosts that
make the same mistake.
The last patch fixes a really nasty xHCI driver bug that could cause
general protection faults when devices stall transfers.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yn5e
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2012-08-08' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
xHCI bug fixes and host quirks.
Hi Greg,
Here's four patches for 3.6. Most are marked for stable as well.
The first one makes the xHCI driver load properly on newer Rensas hosts.
The next two fix issues with the Etron host incorrectly marking short
transfers as successful, and avoiding log warning spam for hosts that
make the same mistake.
The last patch fixes a really nasty xHCI driver bug that could cause
general protection faults when devices stall transfers.
Sarah Sharp
This patch adds the Intel HD Audio Device IDs for the Intel Lynx Point-LP PCH
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
By looking at the current way we're using these definitions I don't
think this commit will fix any bug, but programmers from the future
are evil and will certainly find ways to combine macro expansion with
operator precedence to introduce bugs that are hard to find.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's the only part of the i915_reg.h file that looks totally wrongly
indented, so I assume my editor config is the correct one.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't rely on previous values already set on the register. Everything
we're not explicitly setting should be zero for now.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Correctly erase the values previously set and also check for 6bpc and
10bpc.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During my tests, everything worked even if the wrong polarity was set.
Still, we should try to set the correct values.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mask the value before changing it and also select DVI when needed.
DVI was working in cases where the BIOS was setting the correct value
because we were not masking the value before changing it.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Handy for lazy people like me, or when people forget to add the output
of lspci -nn.
v2: Chris Wilson noticed that we have this duplicated already in the
i915_capabilites debugfs file. But there \n as separator looks better,
which would be a bit verbose in dmesg. Abuse the preprocessor to
extract this all.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Correct the checking for handler returned by PyDict_GetItemString(),
also fix some spelling error and remove some data code in
event_analyzing_sample.py, as suggested by Namhyung Kim.
v2: restore back the wrongly removed trace_unhandled() func
Signed-off-by: Feng Tang <feng.tang@intel.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/20120809134613.067104c4@feng-i7
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Counting the U9540 and the new U8540 as a U8500 family member
does not work. Instead, split the function in two:
cpu_is_u8500_family() covering U8500 and U8520
cpu_is_ux540_family() covering U9540 and U8540
This works much better in practice. Update users to keep the
same behaviour.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 4430 OPP table was being registered for all other OMAP4 variants
too, like 4460 and 4470 causing issues with cpufreq driver
enabled. 4460 and 4470 devices have different OPPs as compared to
4430, and they should be populated seperately. As long as that
happens, let the OPP table registeration happen only on 4430 device.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On OMAP4, if the first CPU fails to get a valid frequency table (this
could happen if the platform does not register any OPP table), the
subsequent CPU instances end up dealing with a NULL freq_table and
crash.
Check for an already existing freq_table, before trying to create one,
and increment the freq_table_users only if the table is sucessfully
created.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: <linux-pm@vger.kernel.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
OMAP4 sleep entry code even though itself don't use many CPU registers
makes call to the v7_flush_dcache_all() which uses them. Since
v7_flush_dcache_all() doesn't make use of stack, the caller must take
care of the stack frame. Otherwise it will lead to corrupted stack frame.
Fix it by saving used registers.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
dma_controller_create is called only from musb_init_controller
which is __devint so annotate dma_controller_create also with
__devint.
fixes the warn
WARNING: vmlinux.o(.devinit.text+0x6fa8): Section mismatch in reference from the function musb_init_controller() to the function .init.text:dma_controller_create()
The function __devinit musb_init_controller() references
a function __init dma_controller_create().
If dma_controller_create is only used by musb_init_controller then
annotate dma_controller_create with a matching annotation.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The driver supports phy_init and phy_shutdown functions to
enable and disable phy for Marvell USB 3.0 controller.
Signed-off-by: Yu Xu <yuxu@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We got a recursive lock in mksubvol because the caller already held
a lock. I think we got into this due to a merge error. Commit a874a63
removed the mnt_want_write call from btrfs_mksubvol and added a
replacement call to mnt_want_write_file in btrfs_ioctl_snap_create_transid.
Commit e7848683 however tried to move all calls to mnt_want_write above
i_mutex. So somewhere while merging this, it got mixed up. The
solution is to remove the mnt_want_write call completely from
mksubvol.
Reported-by: David Sterba <dave@jikos.cz>
Signed-off-by: Alexander Block <ablock84@googlemail.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
This branch fixes the stall during probing the HD-audio driver when
the specified "patch" firmware doesn't exist. It's basically a long-
standing issue, but mostly harmless until the recent rework of
firmware loader base code.
For processing the firmware handling properly for built-in kernels,
implement an asynchronous firmware loading with
request_firmware_nowait(). This means that the codec probing is
deferred when the patch option is specified.
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a preliminary work for the deferred probing for
request_firmware() errors at init.
This patch moves the call of request_firmware() to hda_intel.c, and
call it in the earlier stage of probing rather than
azx_probe_continue().
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When CONFIG_PM is set but CONFIG_PM_SLEEP is unset,
SIMPLE_DEV_PM_OPS() ignores the given functions, and this leads to
compile warnings.
For avoiding this, simply check CONFIG_PM_SLEEP instead of CONFIG_PM.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move unplugging for direct I/O from around ->direct_IO() down to
do_blockdev_direct_IO(). This implicitly adds plugging for direct
writes.
CC: Li Shaohua <shli@fusionio.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Buffered write(2) is not directly tied to IO, so it's not suitable to
handle plug in generic_file_aio_write().
Note that plugging for O_SYNC writes is also removed. The user may pass
arbitrary @size arguments, which may be much larger than the preferable
I/O size, or may cross extent/device boundaries. Let the lower layers
handle the plugging. The plugging code here actually turns them into
no-ops.
CC: Li Shaohua <shli@fusionio.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The SCSI discard request merge never worked, and looks no solution
for in future, let's disable it temporarily.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Do not leak memory by updating pointer with potentially NULL realloc return value.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It is not currently possible to build the gpmi-nand driver without
also building the mxs-dma driver. Clarify this Kconfig and enable
both in the defconfig file so we can build it again with both enabled.
drivers/built-in.o: In function `gpmi_dma_filter':
clk-fixed-factor.c:(.text+0xafc18): undefined reference to `mxs_dma_is_apbh'
make[1]: *** [vmlinux] Error 1
make: *** [sub-make] Error 2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Without this patch, building integrator_defconfig results in:
arch/arm/mach-integrator/core.c:150:1: warning: data definition has no type or storage class [enabled by default]
arch/arm/mach-integrator/core.c:150:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Wimplicit-int]
arch/arm/mach-integrator/core.c:150:1: warning: parameter names (without types) in function declaration [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
The samsung PWM driver has moved to the new PWM subsystem, which
changed the Kconfig symbol for that driver, but the rx1950 and
gta02 boards still uses the old one.
Without this patch, building s3c2410_defconfig results in:
arch/arm/mach-s3c24xx/built-in.o: In function `rx1950_lcd_power':
arch/arm/mach-s3c24xx/mach-rx1950.c:430: undefined reference to `pwm_config'
arch/arm/mach-s3c24xx/mach-rx1950.c:431: undefined reference to `pwm_disable'
arch/arm/mach-s3c24xx/mach-rx1950.c:437: undefined reference to `pwm_config'
arch/arm/mach-s3c24xx/mach-rx1950.c:438: undefined reference to `pwm_enable'
arch/arm/mach-s3c24xx/built-in.o: In function `rx1950_backlight_exit':
arch/arm/mach-s3c24xx/mach-rx1950.c:504: undefined reference to `pwm_free'
arch/arm/mach-s3c24xx/built-in.o: In function `rx1950_backlight_init':
arch/arm/mach-s3c24xx/mach-rx1950.c:487: undefined reference to `pwm_request'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Tushar Behera <tushar.behera@linaro.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
The sa1100 definition of the io_p2v macro has changed in v3.6, and this one
file stopped working because of that.
Without this patch, building hackkit_defconfig results in:
arch/arm/mach-sa1100/leds-hackkit.c: In function 'hackkit_leds_event':
arch/arm/mach-sa1100/leds-hackkit.c:39:4: error: implicit declaration of function 'IOMEM' [-Werror=implicit-function-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
The EETI touchscreen asserts its IRQ line as soon as it has data in its
internal buffers. The line is automatically deasserted once all data has
been read via I2C. Hence, the driver has to monitor the GPIO line and
cannot simply rely on the interrupt handler reception.
In the current implementation of the driver, irq_to_gpio() is used to
determine the GPIO number from the i2c_client's IRQ value.
As irq_to_gpio() is not available on all platforms, this patch changes
this and makes the driver ignore the passed in IRQ. Instead, a GPIO is
added to the platform_data struct and gpio_to_irq is used to derive the
IRQ from that GPIO. If this fails, bail out. The driver is only able to
work in environments where the touchscreen GPIO can be mapped to an
IRQ.
Without this patch, building raumfeld_defconfig results in:
drivers/input/touchscreen/eeti_ts.c: In function 'eeti_ts_irq_active':
drivers/input/touchscreen/eeti_ts.c:65:2: error: implicit declaration of function 'irq_to_gpio' [-Werror=implicit-function-declaration]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org (v3.2+)
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Sven Neumann <s.neumann@raumfeld.com>
Cc: linux-input@vger.kernel.org
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
The irq_to_gpio function was removed from the pxa platform
in linux-3.2, and this driver has been broken since.
There is actually no in-tree user of this driver that adds
this platform device, but the driver can and does get enabled
on some platforms.
Without this patch, building ezx_defconfig results in:
drivers/mfd/ezx-pcap.c: In function 'pcap_isr_work':
drivers/mfd/ezx-pcap.c:205:2: error: implicit declaration of function 'irq_to_gpio' [-Werror=implicit-function-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: stable@vger.kernel.org (v3.2+)
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
