This patch fixes below issues when choosing selector:
1. Current code returns negative selector if min_uV < 900000 which is wrong.
For example, it is possible to satisfy the request with selector = 1 if
the requested min_uV is 850000.
2. Current code may select a voltage lower than requested min_uV.
For example, if the requested min_uV is 945000, current code chooses
selector = 1 which is lower than requested min_uV.
DIV_ROUND_UP to avoid this case.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is to address the following warning during compilation time: (Compile on x86_64)
CC drivers/regulator/core.o
drivers/regulator/core.c: In function '_regulator_do_set_voltage':
drivers/regulator/core.c:2183:10: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
This patch adds a temporary variable to avoid double cast.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When CONFIG_SND_VERBOSE_PRINTK=y is set, the debug print in
hda_auto_parser.c looks really ugly like:
ALSA sound/pci/hda/hda_auto_parser.c:331 mono: mono_out=0x0
ALSA sound/pci/hda/hda_auto_parser.c:334 dig-out=0x12/0x0
ALSA sound/pci/hda/hda_auto_parser.c:335 inputs:
ALSA sound/pci/hda/hda_auto_parser.c:339 Mic=0x11ALSA sound/pci/hda/hda_auto_parser.c:339 Line=0x10
ALSA sound/pci/hda/hda_auto_parser.c:341
ALSA sound/pci/hda/hda_auto_parser.c:343 dig-in=0x13
Better to put one item at each line.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Using devm_clk_get can make the code simpler and smaller.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The idle_bias_off flag is not configured for DAIs not mapped with a codec.
This causes the pm counter to be increased at probe time for the CPU dai
which unbalances the pm counter handling.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
slab.h header file was included twice.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The check for the mux_signal callback was wrong which prevents us to
configure the 6pin port's FSR/CLKR signal mux.
Reported-by: CF Adad <cfadad@rocketmail.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org (3.4+)
Add missing initialization for ret variable. Its initialization
is based on the re_cnt variable, which is being set deep down
in the ftrace_function_filter_re function.
I'm not sure compilers would be smart enough to see this in near
future, so killing the warning this way.
Link: http://lkml.kernel.org/r/1340120894-9465-2-git-send-email-jolsa@redhat.com
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The warkeup_rt self test used msleep() calls to wait for real time
tasks to wake up and run. On bare-metal hardware, this was enough as
the scheduler should let the RT task run way before the non-RT task
wakes up from the msleep(). If it did not, then that would mean the
scheduler was broken.
But when dealing with virtual machines, this is a different story.
If the RT task wakes up on a VCPU, it's up to the host to decide when
that task gets to schedule, which can be far behind the time that the
non-RT task wakes up. In this case, the test would fail incorrectly.
As we are not testing the scheduler, but instead the wake up tracing,
we can use completions to wait and not depend on scheduler timings
to see if events happen on time.
Link: http://lkml.kernel.org/r/1343663105.3847.7.camel@fedora
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Do not rely on any hints from gadget drivers and use DMA mode 1
whenever we expect data of at least the endpoint's packet size and
have not yet received a short packet.
The last packet if short is always transferred using DMA mode 0.
This patch fixes USB throughput issues in mass storage mode for
host to device transfers.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When MISSED_ISOC is set, BUSY is also set. Since, we are handling
MISSED_ISOC as a separate case in third scenario, therefore handle only
BUSY but not MISSED_ISOC in second scenario.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
devm_kfree should not have to be explicitly used.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,d;
@@
x = devm_kzalloc(...)
...
?-devm_kfree(d,x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the pointers that are allocated with devm_kzalloc will be automatically freed,
at unload time.
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that the auto model is the default, these quirks are redundant
and can be removed.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This computer is confirmed working with model=auto on kernel 3.2.
Also, parsing fails with hda-emu with the current model.
Cc: stable@kernel.org (3.2+)
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tidy up a small typo in the HSI function group list.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case of USB bulk transfer, when himem page
is received, the usb_sg_init function sets the
urb transfer buffer to NULL. When such URB
transfer is handled, kernel crashes in PIO mode.
Handle this by mapping the highmem buffer in PIO mode.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Praveena NADAHALLY <praveen.nadahally@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 622859634a (usb: musb: drop a
gigantic amount of ifdeferry) included this change:
@@ -1901,11 +1844,7 @@ static void musb_free(struct musb *musb)
dma_controller_destroy(c);
}
-#ifdef CONFIG_USB_MUSB_HDRC_HCD
- usb_put_hcd(musb_to_hcd(musb));
-#else
kfree(musb);
-#endif
}
/*
Since musb comes from struct usb_hcd's hcd_priv, which is allocated on
the end of that struct, kfree'ing it is not going to work. Replace
kfree(musb) with usb_put_hcd(musb_to_hcd(musb)), which appears to be
the right thing to do here.
Signed-off-by: Brian Downing <bdowning@lavos.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Also properly indent the HB IDs.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is not point in having arch_id as parameter of __arch_decomp_setup(),
nothing in it uses arch_id. The machine id is already exported (and used)
with symbol __machine_arch_type as per mach-types.h.
Removing the pointless macro as well.
Signed-off-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
vcxio, v2v1 and v1v8 are expected to be always on, update the dtsi
for twl6030 to reflect this.
commit '86f5fc' regulator: core: Mark all DT based boards as having
full constraints) caused these to be disabled at late boot causing
OMAP4 boards (using twl6030) to lockup.
Reported-by: Kishon Vijay Abraham I <kishon@ti.com>
Reported-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Rajendra nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Just a small typo fix to make lsxl dtbs compile
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The first idea of the CAN FD implementation started with a new struct
canfd_frame to be used for both CAN FD frames and legacy CAN frames.
The now mainlined implementation supports both CAN frame types simultaneously
and distinguishes them only by their required sizes: CAN_MTU and CANFD_MTU.
Only the struct canfd_frame contains a flags element which is needed for the
additional CAN FD information. As CAN FD implicitly means that the 'Extened
Data Length' mode is enabled the formerly defined CANFD_EDL bit became
redundant and also confusing as an unset bit would be an error and would
always need to be tested.
This patch removes the obsolete CANFD_EDL bit and clarifies the documentation
for the use of struct canfd_frame and the CAN FD relevant flags.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some 8086:10c9 NICs have a problem completing the ethtool loopback test.
The result looks like this:
ethtool -t eth1
The test result is FAIL
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 13
Link test (on/offline) 0
A bisect clearly points to commit a95a07445e.
However that seems to only trigger the bug. While adding some printk the
problem disappeared, so this might be a timing issue. After some trial and
error I discovered that adding a small delay just before igb_write_phy_reg()
in igb_integrated_phy_loopback() allows the loopback test to succeed.
I was unable to figure out the root cause so far but I expect it to be
somewhere in the following executing path
igb_integrated_phy_loopback
->igb_write_phy_reg_igp
->igb_write_phy_reg_mdic
->igb_acquire_phy_82575
->igb_acquire_swfw_sync_82575
The problem could only be observed on 8086:10c9 NICs so far and not all
of them show the behaviour. I did not restrict the workaround to this
type of NIC as it should do no harm to other igb NICs.
With the patch below the loopback test succeeded 500 times in a row
using a NIC that would otherwise fail.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
A bus trace shows that while executing e1000e_down, TCTL is cleared except
for the PSP bit. This occurs while in the middle of fetching a TSO packet
since the Tx packet buffer is full at that point. Before the device is
reset, the e1000_watchdog_task starts to run from the middle (it was
apparently pre-empted earlier, although that is not in the trace) and sets
TCTL.EN. At that point, 82571 transmits the corrupted packet, apparently
because TCTL.MULR was cleared in the middle of fetching a packet, which is
forbidden.
Driver should just clear TCTL.EN in e1000_reset_hw_82571 instead of
clearing the entire register, so as not to change any settings in the
middle of fetching a packet.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Found that commit d478eb44 was a bad commit.
If the link partner is transmitting codeword (even if NULL codeword),
then the RXCW.C bit will be set so check for RXCW.CW is unnecessary.
Ref: RH BZ 840642
Reported-by: Fabio Futigami <ffutigam@redhat.com>
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
CC: Marcelo Ricardo Leitner <mleitner@redhat.com>
CC: stable <stable@vger.kernel.org> [2.6.38+]
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
The random config builds with PM and !ARM_CPU_SUSPEND breaks with below
error on omap2plus_defconfig.
arch/arm/mach-omap2/sleep44xx.S:323: undefined reference to `cpu_resume'
arch/arm/mach-omap2/omap-mpuss-lowpower.c:278: undefined reference to `cpu_suspend'
This is because recently merged OMAP5 platform shares the common files
with OMAP4 but doesn't select ARM_CPU_SUSPEND. Without the ARM_CPU_SUSPEND
the sleep code is meaningless.
Fix the same by adding ARM_CPU_SUSPEND for OMAP5. The suggestion came from
Russell King in an off-list discussion.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Kevin Hilman <khilman@ti.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Naming of emma-prp related clocks for the i.MX27 is not correct.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add am33xx wdt node.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
[tony@atomide.com: I messed up and produced an empty commit db27ac80 with stg apply]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move gpc4 to the end of the automatically processed gpio controllers so
we don't taint the automatic offset calculation.
This bug caused all controllers coming after gpc4 to map to the
incorrect address. The result is <&gpd1 0 0 0 0> would actually map to
GPIO 0 in gpd0.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add alias for gpio nodes, so that gpio driver can identify the port
number and then specify a sensible gpio base rather than using the
one dynamically allocated by gpio core.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, unlike the non-DT probe where the gpio base is specified
with pdev->id, the DT probe uses the base dynamically allocated by
gpio core, which uses a completely different numbering scheme. This
causes two issues to user space applications which access sysfs entry
/sys/class/gpio/gpioN.
* It breaks the compatibility with user space applications between
non-DT and DT kernels.
* It's not intuitive and sometimes hard for users to map the Linux
gpio number to the actual hardware pin.
Use alias to identify the gpio port/bank, and then the gpio base
can be specified with port id to solve above issues. If alias is not
defined in device tree, the base number dynamically allocated by gpio
core will be used.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As with the ThinkPad Models X230 Tablet and T530 the X230 needs a qurik to
correctly set up the pins for the dock port.
Signed-off-by: Felix Kaechele <felix@fetzig.org>
Cc: <stable@vger.kernel.org> [v3.2+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes the following sparse warnings:
drivers/usb/dwc3/gadget.c:1096:7: warning: symbol 'ret' shadows an earlier one
drivers/usb/dwc3/gadget.c:1058:8: originally declared here
drivers/usb/dwc3/gadget.c:1100:16: warning: symbol 'dwc' shadows an earlier one
drivers/usb/dwc3/gadget.c:1057:15: originally declared here
drivers/usb/dwc3/gadget.c:1118:16: warning: symbol 'dwc' shadows an earlier one
drivers/usb/dwc3/gadget.c:1057:15: originally declared here
drivers/usb/dwc3/gadget.c:1800:19: warning: symbol 'dep' shadows an earlier one
drivers/usb/dwc3/gadget.c:1778:18: originally declared here
Also, fix the potential checkpatch errors around the if() loops that
this fix patch can create.
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Run the mprotect.c microbenchmark on all our families >= K8 and preset
the flushall shift variable accordingly.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1344272439-29080-5-git-send-email-bp@amd64.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Push the max CPUID leaf check into the ->detect_tlb function and remove
general test case from the generic path.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1344272439-29080-3-git-send-email-bp@amd64.org
Acked-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The TLB characteristics appeared like this in dmesg:
[ 0.065817] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512
[ 0.065817] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512
[ 0.065817] tlb_flushall_shift is 0xffffffff
where tlb_flushall_shift is actually -1 but dumped as a hex number.
However, the Kconfig option CONFIG_DEBUG_TLBFLUSH and the rest of the
code treats this as a signed decimal and states "If you set it to -1,
the code flushes the whole TLB unconditionally."
So, fix its formatting in accordance with the other references to it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1344272439-29080-2-git-send-email-bp@amd64.org
Acked-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
When installing a flow with an action to set a particular field we
need to validate that the packets that are part of the flow actually
contain that header. With IP we use zeroed addresses and with TCP/UDP
the check is for zeroed ports. This check is overly broad and can catch
packets like DHCP requests that have a zero source address in a
legitimate header. This changes the check to look for a zeroed protocol
number for IP or for both ports be zero for TCP/UDP before considering
the header to not exist.
Reported-by: Ethan Jackson <ethan@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
