Implement a new "fail-open" mode where packets are not dropped
upon queue-full condition. This mode can be enabled/disabled per
queue using netlink NFQA_CFG_FLAGS & NFQA_CFG_MASK attributes.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Vivek Kashyap <vivk@us.ibm.com>
Signed-off-by: Sridhar Samudrala <samudrala@us.ibm.com>
It was scheduled to be removed.
Cc: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
It was scheduled to be removed.
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The nat_rtp_rtcp hook takes two separate parameters port and rtp_port.
port is expected to be the real h245 address (found inside the packet).
rtp_port is the even number closest to port (RTP ports are even and
RTCP ports are odd).
However currently, both port and rtp_port are having same value (both are
rounded to nearest even numbers).
This works well in case of openlogicalchannel with media (RTP/even) port.
But in case of openlogicalchannel for media control (RTCP/odd) port,
h245 address in the packet is wrongly modified to have an even port.
I am attaching a pcap demonstrating the problem, for any further analysis.
This behavior was introduced around v2.6.19 while rewriting the helper.
Signed-off-by: Jagdish Motwani <jagdish.motwani@elitecore.com>
Signed-off-by: Sanket Shah <sanket.shah@elitecore.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch addresses two issues:
a) Fix usage of u32 and __be32 that causes endianess warnings via sparse.
b) Ensure consistent hashing in a cluster that is composed of big and
little endian systems. Thus, we obtain the same hash mark in an
heterogeneous cluster.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
As per Al Viro's suggestion, this increases the buffer size used
for these two files. This provides a speed up of slightly less than
8x (i.e. proportional to the buffer size) for cases when we have
large numbers of glocks.
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Commit "62f38455 UBI: modify ubi_wl_flush function to clear work queue for a lnum"
takes the 'work_sem' semaphore in write mode for the entire loop, which is not
very good because it will block other workers for potentially long time. We do
not need to have it in write mode - read mode is enough, and we do not need to
hole it over the entire loop. So this patch turns changes the locking: takes
'work_sem' in read mode and pushes it down to the loop.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Until now, writing to error count caused the code to reset the
thresholding bank to the current thresholding limit and start counting
errors from the beginning.
This is misleading and unclear, and can be accomplished by writing the
old thresholding limit into ->threshold_limit.
Make error_count read-only with the functionality to show the current
error count.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
We have rdmsr_on_cpu() now so remove locally defined solution in favor
of the generic one.
No functionality change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
If one sets the threshold limit, say to 25:
$ echo 25 > machinecheck0/threshold_bank4/misc0/threshold_limit
and then reads it back again, it gives
$ cat machinecheck0/threshold_bank4/misc0/threshold_limit
19
which is actually 0x19 but we don't know that.
Make all output decimal.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Well, instead of having a real bank 4 on the BSP of each node and
symlinks on the remaining cores, we push it up into the amd_northbridge
descriptor which now contains a pointer to the northbridge bank 4
because the bank is one per northbridge and, as such, belongs in the NB
descriptor anyway.
Each time we hotplug CPUs, we use the northbridge pointer to copy the
shared bank into the per-CPU array of threshold_banks pointers, or
destroy it when the last CPU on the node goes offline, or create it when
the first comes online.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The code used to create a symlink on all non-BSP cores of a node when
the MCi_MISCj bank is present once per node. (This is generally the
case with bank 4 on AMD). However, these sysfs links cause a bunch
of problems with cpu off-/onlining testing and are, as such, a bit
overengineered. IOW, there's nothing wrong with having normal sysfs
files for the shared banks since the corresponding MSRs are replicated
across each core anyway.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add the F3 PCI id of F15h, model 0x10 to pci_ids.h and to the amd_nb
code which generates the list of northbridges on an AMD box. Shorten
define name while at it so that it fits into pci_ids.h.
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The iommu_shutdown callback is not initialized when the AMD
IOMMU driver runs in passthrough mode. Fix that by moving
the callback initialization before the check for
passthrough mode.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
snd_hda_param_read() return value -1 means error, others are responses
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
if EPSS supported, transition from D3 state to D0 state in less
than 10ms
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add function to check whether power states supported by specific
codec node.
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes the following sparse warning:
drivers/dma/pl330.c:2542:5: warning: symbol 'add_desc' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This fix audio underrun issue. When SNDRV_PCM_TRIGGER_STOP
and SNDRV_PCM_TRIGGER_START, it calls prepare again. buf_tail
should be reset to zero.
So move buf_tail initialization into prepare function.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Commit eab2158558 ("dmaengine: pl330: dont complete descriptor for
cyclic dma") wrongly completes descriptor for cyclic dma, hence following
BUG_ON is still hit with cyclic DMA operations.
kernel BUG at drivers/dma/dmaengine.h:53!
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
This patch adds the support for D_CAN controller driver to the existing
C_CAN driver.
Bosch D_CAN controller is a full-CAN implementation which is compliant
to CAN protocol version 2.0 part A and B. Bosch D_CAN user manual can be
obtained from: http://www.semiconductors.bosch.de/media/en/pdf/
ipmodules_1/can/d_can_users_manual_111.pdf
A new array is added for accessing the d_can registers, according to d_can
controller register space.
Current D_CAN implementation has following limitations, this is done
to avoid large changes to the C_CAN driver.
1. Message objects are limited to 32, 16 for RX and 16 for TX. C_CAN IP
supports upto 32 message objects but in case of D_CAN we can configure
upto 128 message objects.
2. Using two 16bit reads/writes for accessing the 32bit D_CAN registers.
3. These patches have been tested on little endian machine, there might
be some hidden endian-related issues due to the nature of the accesses
(32-bit registers accessed as 2 16-bit registers). However, I do not
have a big-endian D_CAN implementation to confirm.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
c_can uses overlay structure for accessing c_can module registers.
With this kind of implementation it is difficult to add one more ip
which is similar to c_can in functionality but different register
offsets.
This patch changes the overlay structure implementation to an array
with register offset as index. This way we can overcome the above
limitation.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Commit "f70b7e5 UBIFS: remove Kconfig debugging option" broke UBIFS and it
refuses to initialize if debugfs (CONFIG_DEBUG_FS) is disabled. I incorrectly
assumed that debugfs files creation function will return success if debugfs
is disabled, but they actually return -ENODEV. This patch fixes the issue.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Commit "aa44d1d UBI: remove Kconfig debugging option" broke UBI and it
refuses to initialize if debugfs (CONFIG_DEBUG_FS) is disabled. I incorrectly
assumed that debugfs files creation function will return success if debugfs
is disabled, but they actually return -ENODEV. This patch fixes the issue.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
The raw data reading process (ak8975_read_axis) sets the
single measurement mode to take a sample and once the
conversion is completed the device enters into power-down
mode automatically, therefore there is no need to enable
a flag for this to happen.
Signed-off-by: Leed Aguilar <leed.aguilar@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fuse ROM data access mode is the only mode which does not
transition to power-down mode automatically.
As per the AK8975 data sheet, it is recomended to set the
power-down mode first before attempting to change into
another mode.
Signed-off-by: Leed Aguilar <leed.aguilar@ti.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use scnprint instead of snprintf, because snprintf returns the number of bytes
that would have been written to the buffer if there was enough space, and as a
result writing to buf[len-1] might cause a access beyond the buffers limits.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/iio/frequency/adf4350.c:316:32: warning: ‘val’ may be used uninitialized in this function
[-Wuninitialized]
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When uninstalling a device, the call to the ipack_bus_ops remove() frees
resources in the ipack device driver but without unregistering the device.
It generates a kernel oops when somebody wants to unregister the device.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tpci200->info is used later when uninstalling the module. As there is another
kfree in the proper place, this patch removes the wrong one.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When uninstalling a device, there is a loop of calls that produces, at the end,
two calls to __ipoctal_remove() function with the same ipack_device argument.
The first time works fine, but the second will fail in tty_unregister_driver()
To avoid this situation, the call to __ipoctal_remove() it is done only from the
ipack bus driver and not from the ipack device driver.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a bus driver calls ipack_driver_register(), it should manages the returning
NULL value to undo all the operations it did before this call, and print the
corresponding trace.
It is not a task for the ipack driver to call the remove() function here.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use idr interface to give the bus number. That way, we remove the
limitation of 64 buses.
The mutex is removed because the ida interface uses spinlocks inside, so it is
not needed an extra lock.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ipack_device_register() is called, the variable
tpci200->slots[dev->slot].dev has not assigned a value and it gives an error
when the mezzanine driver is reading a register from the board for the match()
function, as all the I/O functions call check_slot().
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This field is not needed at all, as the IRQ is registered for the carrier not
for the mezzanine.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid a dereference of a NULL pointer, the availability of the function is
checked before its use.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tpci200_slot_map_space() should return 0 if the operation was properly
done. If not, the caller will think that something wrong happened.
This patch establish the returned value to 0. It is overwritten in case of
error.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tpci200_slot_unmap_space() should return 0 if the operation was properly done. If
not, the caller will think that something wrong happened.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should return the same value given by the match function of the ipack_driver
that has been called.
Returning 0 here, means that the match has failed and it could be succeed.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To perform the installation of a mezzanine it was needed to write on these
files, now it is not needed at all as the device model is properly implemented.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>