During wiphy registration signal_type is initialized to
CFG80211_SIGNAL_TYPE_MBM. So convert signal strength from dBm to
mBm. Also, the value is absolute. Make it negative before
sending to cfg80211.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lets the user know which interface has failed
the check_sdata_in_driver check.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since some of the HT code pre-dates 802.11n-2009
some names are wrong. The one that bothers me most
is that "HT operation" is called "HT information"
in our code and that causes confusion.
Rename "HT information" to "HT operation" and also
the control_chan field to primary_chan to match
the name used in the spec.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes the probe frame (nullfunc) is stuck at the hw queue. so that
the mac80211 terminates the connection as it wont see the tx status.
Instead of waiting for long period for ack status, lets call flush
to get nullfunc status immediately. It also helps to send the nullfunc
till max tries reached.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There might be latency at AP side to update TIM IE which could cause the
station to send pspoll frame even after the wakeup. If the powersave is
disabled, the nullfunc notification alone is sufficient to receive
frames from the AP. And if the pspoll frame was already sent, no need to
resend the frame till it was acked by AP.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the experiment with Azimuth ADEPT-n testbed where the APs transmit
power was reduced to 25% and the signal strength was futher attenuated
by 20dB and induced a path loss of ~7dB, the station was reporting
beacon losses and the following issue were observed.
* rx clear is stuck at low for more than 300ms
* dcu chain and complete state is stuck at one of the hang signature
This patch triggers the hang detection logic that recovers the chip
from any of the above conditions. As the issue was originally reported
in ChromeOs with AR9382 chips, this detection logic is enabled only for
AR9380/2 chips.
Cc: Paul Stewart <pstew@google.com>
Reported-by: Gary Morain <gmorain@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch improves ANI operations by switching among the immunity
levels based on PHY errors and beacon rssi which will adjust receiver
desensitizing parameters. The changes are
* Configure the Weak Signal Detection based on current immunity value.
* At highest OFDM immunity level poor performance was observed with
strong interference. By tuning the FIR step and spur immunity levels
and not changing any weak signal detection thresholds at any level
helped to improve the performance.
* ANI took long time to recover back to lower immunity levels on heavy
data load. As the listen time got reset to zero before reaching to
the 5x of aniperiod, the immunity level is not lowering back even
without any interference. This patch fix that.
Cc: Paul Stewart <pstew@google.com>
Cc: Susinder Gulasekaran <susinder@qca.qualcomm.com>
Signed-off-by: Suresh Chandrasekaran <csuresh@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Free extra as done in the error-handling code just above.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the rate-control indexing is incorrectly set up, mac80211 issues
a warning and returns NULL from the call to ieee80211_get_tx_rate().
When this happens, avoid a NULL pointer dereference.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the control-rate tables are not set up correctly, it makes
little sense to spam the logs, thus change the WARN_ON to WARN_ON_ONCE.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before the switch to asynchronous firmware loading (mainline commit b0302ab),
it was necessary to load firmware when initializing the first of the units
in a dual-mac system. After the change, it is necessary to load firmware in
both units.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nl80211 handling code should ensure as much as
it can that the interface is in a valid state, it
can certainly ensure the interface is running.
Not doing so can cause calls through mac80211 into
the driver that result in warnings and unspecified
behaviour in the driver.
Cc: stable@vger.kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TU_TO_EXP_TIME() macro already includes the
"jiffies +" piece of the calculation, so don't
add jiffies again.
Reported-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to the case where we are changing from one framebuffer to
another, we need to be sure that there are no pending WAIT_FOR_EVENTs on
the pipe for the current framebuffer before switching. If we disable the
pipe, and then try to execute a WAIT_FOR_EVENT it will block
indefinitely and cause a GPU hang.
We attempted to fix this in commit 85345517fe
(drm/i915: Retire any pending operations on the old scanout when switching)
for the case of mode switching, but this leaves the condition where we
are switching off the pipe vulnerable.
There still remains the race condition were a display may be unplugged,
switched off by the core, a uevent sent to notify the DDX and the DDX
may issue a WAIT_FOR_EVENT before it processes the uevent. This window
does not exist if the pipe is only switched off in response to the
uevent. Time to make sure that is so...
Reported-by: Francis Leblanc <Francis.Leblanc-Lebeau@verint.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36515
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45413
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: fixup spelling in comment, noticed by Eugeni.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The destination color key is always enabled for IVB. Removed
the line that does this.
Signed-off-by: Armin Reese <armin.c.reese@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no need to send a notification if ovs_vport_set_options() failed
and ovs_vport_cmd_set() did not change anything.
Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Some configurations produce the following compiler warning:
drivers/hwmon/pmbus/pmbus_core.c: In function 'pmbus_show_boolean':
drivers/hwmon/pmbus/pmbus_core.c:752: warning: 'val' may be used uninitialized in this function
While this is a false positive, it can easily be fixed by overloading the return
value from pmbus_get_boolean with both val and error return code (val is a
boolean and thus never negative).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some configurations produce the following compiler warning:
drivers/hwmon/smsc47m1.c: In function 'sm_smsc47m1_init':
drivers/hwmon/smsc47m1.c:938: warning: 'address' may be used uninitialized in this function
While this is a false positive, it can easily be fixed by overloading the return
value from smsc47m1_find with both address and error return code (the address
is an unsigned short and thus never negative). This also reduces module size by
a few bytes (46 bytes for x86_64).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
In some configurations, BUG() does not result in an endless loop but returns
to the caller. This results in the following compiler warning:
drivers/hwmon/acpi_power_meter.c: In function 'show_str':
drivers/hwmon/acpi_power_meter.c:380: warning: 'val' may be used uninitialized in this function
Fix the warning by setting val to an empty string after BUG().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some configurations produce the following compiler warning:
drivers/hwmon/smsc47b397.c: In function 'smsc47b397_init':
drivers/hwmon/smsc47b397.c:385: warning: 'address' may be used uninitialized in this function
While this is a false positive, it can easily be fixed by overloading the return
value from smsc47b397_find with both address and error return code (the address
is an unsigned short and thus never negative). This also reduces module size by
a few bytes (64 bytes for x86_64).
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
tty_buffer_request_room is well protected, but while after it returns,
it releases the port->lock. tty->buf.tail might be modified
by either irq handler or other threads. The patch adds more protection
by holding the lock across tty buffer finding and buffer filling.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Xiaobing Tu <xiaobing.tu@intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
set_get_cmap() ignored the result of {get,put}_user(), causing ioctl(vt,
{G,P}IO_CMAP, 0xdeadbeef) to silently fail.
Another side effect of this: calling the PIO_CMAP ioctl with an invalid
buffer would zero the default colormap and the palette for all vts (all
colors set to black).
Leave the default colormap intact and return -EFAULT when
reading/writing to the userspace buffer fails.
Signed-off-by: Michael Gehring <mg@ebfe.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, occurring line status interrupt,
returned value is not set in interrupt handler function.
As a result, 0 can be returned.
This patch adds setting returned value.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
%02x format is easier to understand better than %d.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Target uart register access size is 8bit.
However, 32bit is used at 2 points.
This patch modifies type "unsigned int" to "unsigned char".
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This means converting an atomic counter to a counter protected by
lock. This is the first step needed to convert the rest of the code to
the tty_port helpers.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_wakeup is safe to be called from all contexts. No need to schedule
a work for that. Let us call it directly like in other drivers.
This allows us to kill another member of rfcomm_dev structure.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch the refcounting from manual atomic plays with refcounter to the
one offered by tty_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the code is identical, use the tty_port_block_til_ready helper
instead of re-implemented variant.
The code does not perform rtsdts handling, hence we do not need to
provide tty port hooks for them. The default ones will be used
instead. The only necessary thing is to provide tty_port_operations.
It is empty, but has to be there...
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need tty at some places, but info->tty might be NULL at those. Let
us propagate tty from callers where we know we have a valid tty. This
will make a switch to tty refcounting simpler.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
flags passed to local_irq_save/restore should be ulong. Switch tehem
to that. Otherwise we get compilation warnings:
.../68328serial.c:248:9: warning: comparison of distinct pointer types lacks a cast [enabled by default]
.../68328serial.c:257:9: warning: comparison of distinct pointer types lacks a cast [enabled by default]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not everything from struct m68k_serial is really used. So remove
unused or only-set members of that structure. Next step is to move it
to 68328serial.c and remove 68328serial.h completely.
This change also takes status_handle and batten_down_hatches away
since they use break_abort but do nothing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial_state in 68328serial.h is a duplicated structure. One is
defined in linux/serial.h. So let us use that instead. And since the
serial flags are identical, use ones from there too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: linux-m68k@lists.linux-m68k.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>