Convert to %pM instead of using custom code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260603112011.230890-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dsa_port_from_netdev() may return a valid port from a different switch
chip. Programming another chip's port index into the local hardware
causes redirection to the wrong port, or an out-of-bounds access if the
index exceeds the local chip's port count.
Apply a minimal fix that adds a check to catch this case and adjusts the
extack message. When cls->common.skip_sw is not set, the operation could
instead redirect to the upstream port and let the software or upstream
switch(es) handle the forward, but that is not addressed here.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20260530003940.2000994-1-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MIPS bcm53xx platform still uses the legacy gpiolib interfaces based
on gpio numbers, but other platforms do not.
Hide these interfaces inside of the existing #ifdef block and use the
modern interfaces in the common parts of the driver to allow building
it when the gpio_set_value() is left out of the kernel.
Reviewed-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20260601165716.648230-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add serdes and pcs_ops functions for mv88e6321. In mv88e6321
2 ports support serdes functionality; port 0 and port 1. These ports are
serdes-only ports.
Changes:
1. Add a function support to return the lane address for the port based on
cmode.
2. Reuse mv88e6352's serdes_get_regs* and pcs_init functions for mv88e6321.
Tested on mv88e6321 switch port 0.
Co-developed-by: Thomas Eckerman <thomas.eckerman.ext@ericsson.com>
Signed-off-by: Thomas Eckerman <thomas.eckerman.ext@ericsson.com>
Signed-off-by: Fidan Aliyeva <fidan.aliyeva.ext@ericsson.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260528210310.1365858-4-fidan.aliyeva.ext@ericsson.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Changes:
1. Replace serdes check by mv88e6352_g2_scratch_port_has_serdes in
mv88e6352_pcs_init function by mv88e6xxx_serdes_get_lane function making it
more generic.
2. Replace serdes checks in mv88e6352_serdes_get_* functions with
mv88e6xxx_serdes_get_lane making them more generic.
3. Add lane argument to mv88e6352_serdes_read so it can be reused later for
6321.
Co-developed-by: Thomas Eckerman <thomas.eckerman.ext@ericsson.com>
Signed-off-by: Thomas Eckerman <thomas.eckerman.ext@ericsson.com>
Signed-off-by: Fidan Aliyeva <fidan.aliyeva.ext@ericsson.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260528210310.1365858-3-fidan.aliyeva.ext@ericsson.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Changes:
1. Add mv88e6352_serdes_get_lane function which checks if the port
supports SERDES by calling mv88e6352_g2_scratch_port_has_serdes. Then
returns the address of the SERDES lane.
2. Add this function as .serdes_get_lane member to all the chip
versions which use mv88e6352_pcs_init.
Co-developed-by: Thomas Eckerman <thomas.eckerman.ext@ericsson.com>
Signed-off-by: Thomas Eckerman <thomas.eckerman.ext@ericsson.com>
Signed-off-by: Fidan Aliyeva <fidan.aliyeva.ext@ericsson.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260528210310.1365858-2-fidan.aliyeva.ext@ericsson.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
NET_DSA_NETC_SWITCH selects NXP_NTMP, NXP_NETC_LIB and FSL_ENETC_MDIO,
but these symbols depend on NET_VENDOR_FREESCALE which may not be
enabled. This results in Kconfig warnings and linker errors like:
undefined reference to `ntmp_bpt_update_entry'
undefined reference to `ntmp_fdbt_search_port_entry'
undefined reference to `ntmp_free_cbdr'
undefined reference to `enetc_hw_alloc'
...
Therefore, add "depends on NET_VENDOR_FREESCALE" to NET_DSA_NETC_SWITCH,
ensuring that the selected symbols NXP_NTMP, NXP_NETC_LIB and
FSL_ENETC_MDIO, which all depend on NET_VENDOR_FREESCALE, can only be
selected when that dependency is already satisfied.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202605240046.8MvKuOMg-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202605240706.EuGmnrz5-lkp@intel.com/
Fixes: 187fbae024 ("net: dsa: netc: introduce NXP NETC switch driver for i.MX94")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260524070310.2429819-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no register access anymore in
mv88e6352_g2_scratch_port_has_serdes. So, remove the locks
surrounding the function.
Co-developed-by: Thomas Eckerman <thomas.eckerman.ext@ericsson.com>
Signed-off-by: Thomas Eckerman <thomas.eckerman.ext@ericsson.com>
Signed-off-by: Fidan Aliyeva <fidan.aliyeva.ext@ericsson.com>
Link: https://patch.msgid.link/20260521202924.727929-5-fidan.aliyeva.ext@ericsson.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
1. Refactor mv88e6352_g2_scratch_port_has_serdes to use the cached
scratch config3 value instead of reading it everytime.
2. Remove err<0 check from mv88e6352_phylink_get_caps as it is never
true anymore
Co-developed-by: Thomas Eckerman <thomas.eckerman.ext@ericsson.com>
Signed-off-by: Thomas Eckerman <thomas.eckerman.ext@ericsson.com>
Signed-off-by: Fidan Aliyeva <fidan.aliyeva.ext@ericsson.com>
Link: https://patch.msgid.link/20260521202924.727929-4-fidan.aliyeva.ext@ericsson.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Changes:
1. Add g2_scratch_config3 member to mv88e6xxx_chip.
2. Add mv88e6352_g2_cache_global_scratch_config3 which reads the
CONFIG3 value from the scratch register and caches it.
3. Call this function in mv88e6352_reset.
Co-developed-by: Thomas Eckerman <thomas.eckerman.ext@ericsson.com>
Signed-off-by: Thomas Eckerman <thomas.eckerman.ext@ericsson.com>
Signed-off-by: Fidan Aliyeva <fidan.aliyeva.ext@ericsson.com>
Link: https://patch.msgid.link/20260521202924.727929-3-fidan.aliyeva.ext@ericsson.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
1. Add mv88e6352_reset which calls the previous ops->reset function
- mv88e6352_g1_reset.
2. Make all 6352 family use this new function as ops->reset
Co-developed-by: Thomas Eckerman <thomas.eckerman.ext@ericsson.com>
Signed-off-by: Thomas Eckerman <thomas.eckerman.ext@ericsson.com>
Signed-off-by: Fidan Aliyeva <fidan.aliyeva.ext@ericsson.com>
Link: https://patch.msgid.link/20260521202924.727929-2-fidan.aliyeva.ext@ericsson.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
phy_read() and phy_write() are handled through common functions that
redirect the treatment to ksz_dev_ops callbacks. This layer of
indirection isn't needed since we now have a dsa_switch_ops for each
kind of switch
Remove one indirection layer for KSZ switches, by connecting the
ksz_dev_ops::phy_r() and ksz_dev_ops::phy_w() operations directly to
dsa_switch_ops.
Remove the now unused phy_r()/phy_w() callbacks from ksz_dev_ops.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260521-clean-ksz-2nd-series-v3-8-75c38971c19a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ksz_sw_mdio_read() and ksz_sw_mdio_write() respectively call
ksz_dev_ops::phy_r() and ksz_dev_ops::phy_w() just like
dsa_switch_ops::phy_read() and dsa_switch_ops::phy_write() do.
Call dsa_switch_ops::phy_read() from ksz_sw_mdio_read() and
dsa_switch_ops::phy_write() from ksz_sw_mdio_write() so we'll be able
to get rid of the useless indirections provided by ksz_dev_ops in
upcoming patch.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260521-clean-ksz-2nd-series-v3-7-75c38971c19a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
port_setup() is handled through a common function that redirects
the treatment to ksz_dev_ops callbacks. This layer of indirection
isn't needed since we now have a dsa_switch_ops for each switch family
Remove one indirection layer for KSZ switches, by connecting the
ksz_dev_ops :: port_setup() operations directly to dsa_switch_ops.
Make ksz9477_set_default_prio_queue_mapping() non-static since it's used
by ksz_common for tc operations and by ksz9477.c for this port_setup().
Remove the now unused port_setup() callback from ksz_dev_ops.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260521-clean-ksz-2nd-series-v3-6-75c38971c19a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All switch families have been converted to have their own
ds->ops->setup() methods and to call the common ksz_teardown().
Remove the no longer used ksz_setup() function and the associated
ksz_dev_ops callbacks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260521-clean-ksz-2nd-series-v3-5-75c38971c19a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The KSZ switch families are sufficiently different that a common
ds->ops->setup() - ksz_setup() with micro-managed dev_ops->reset(),
dev_ops->pcs_create(), dev_ops->config_cpu_port(),
dev_ops->enable_stp_addr(), dev_ops->setup() seems to be too convoluted.
I am proposing to make each KSZ switch family part ways for
dsa_switch_ops :: setup() and teardown(), to allow them greater
flexibility. This here is the implementation for ksz8, which is
nothing other than a copy of ksz_setup() with the dev_ops function
pointers replaced with direct function calls.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260521-clean-ksz-2nd-series-v3-4-75c38971c19a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The KSZ switch families are sufficiently different that a common
ds->ops->setup() - ksz_setup() with micro-managed dev_ops->reset(),
dev_ops->pcs_create(), dev_ops->config_cpu_port(),
dev_ops->enable_stp_addr(), dev_ops->setup() seems to be too convoluted.
I am proposing to make each KSZ switch family part ways for
dsa_switch_ops :: setup() and teardown(), to allow them greater
flexibility. This here is the implementation for ksz9477, which is
nothing other than a copy of ksz_setup() with the dev_ops function
pointers replaced with direct function calls.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260521-clean-ksz-2nd-series-v3-3-75c38971c19a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The KSZ switch families are sufficiently different that a common
ds->ops->setup() - ksz_setup() with micro-managed dev_ops->reset(),
dev_ops->pcs_create(), dev_ops->config_cpu_port(),
dev_ops->enable_stp_addr(), dev_ops->setup() seems to be too convoluted.
I am proposing to make each KSZ switch family part ways for
dsa_switch_ops :: setup() and teardown(), to allow them greater
flexibility. This here is the implementation for lan937x, which is
nothing other than a copy of ksz_setup() with the dev_ops function
pointers replaced with direct function calls.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260521-clean-ksz-2nd-series-v3-2-75c38971c19a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ksz_switch driver is one of the few which reset the switch when
unbinding the driver or shutting down - in the same category with
ar9331_sw_remove(), bcm_sf2_sw_remove(), and ks8995_remove(),
vsc73xx_remove() and lan9303_remove().
I don't think there exists any requirement to do this, and in fact it
does create complications for WoL, as the code already shows.
My issue with this logic is that it is the only thing keeping
dev_ops->reset() necessary, which I would like to remove after
individual KSZ switch families get their own setup() and teardown()
methods that don't go through dev_ops.
Don't reset the switch when unbinding the driver or shutting down.
Remove the exit callbacks from the ksz_dev_ops.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260521-clean-ksz-2nd-series-v3-1-75c38971c19a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
React to TC_SETUP_QDISC_TBF and configure the egress shaper as
appropriate with the maximum rate and burst size requested by the user.
Per queue shaper is possible, though not touched in this commit.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://patch.msgid.link/20260521010320.208138-4-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the ethtool private statistics interface to expose additional
port-level and MAC-level counters that are not covered by the standard
IEEE 802.3 statistics. The pMAC counters are only reported when the port
supports Frame Preemption (802.1Qbu/802.3br).
Note that although rtnl_link_stats64 provides some standard statistics
such as rx octets, rx frame errors, rx dropped packets, and tx packets,
these are overall port statistics. The NETC switch supports preemption
on each port, and each port has two MACs (eMAC and pMAC). The driver
private statistics are used to obtain statistics for each MAC, allowing
users to perform analysis and debugging.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260518082506.1318236-16-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Each user port of the NETC switch supports 802.3 basic and mandatory
managed objects statistic counters and IETF Management Information
Database (MIB) package (RFC2665) and Remote Network Monitoring (RMON)
counters. And all of these counters are 64-bit registers. In addition,
some user ports support preemption, so these ports have two MACs, MAC
0 is the express MAC (eMAC), MAC 1 is the preemptible MAC (pMAC). So
for ports that support preemption, the statistics are the sum of the
pMAC and eMAC statistics.
Note that the current switch driver does not support preemption, all
frames are sent and received via the eMAC by default. The statistics
read from the pMAC should be zero.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260518082506.1318236-15-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The buffer pool is a quantity of memory available for buffering a group
of flows (e.g. frames having the same priority, frames received from the
same port), while waiting to be transmitted on a port. The buffer pool
tracks internal memory consumption with upper bound limits and optionally
a non-shared portion when associated with a shared buffer pool. Currently
the shared buffer pool is not supported, it will be added in the future.
For i.MX94, the switch has 4 ports and 8 buffer pools, so each port is
allocated two buffer pools. For frames with priorities of 0 to 3, they
will be mapped to the first buffer pool; For frames with priorities of
4 to 7, they will be mapped to the second buffer pool. Each buffer pool
has a flow control on threshold and a flow control off threshold. By
setting these threshold, add the flow control support to each port.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260518082506.1318236-14-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Expand the NETC switch driver with several foundational features:
- FDB and MDB management
- STP state handling
- MTU configuration
- Port setup/teardown
- Host flooding support
At this stage, the driver operates only in standalone port mode. Each
port uses VLAN 0 as its PVID, meaning ingress frames are internally
assigned VID 0 regardless of whether they arrive tagged or untagged.
Note that this does not inject a VLAN 0 header into the frame, the VID
is used purely for subsequent VLAN processing within the switch.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260518082506.1318236-13-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Different versions of NETC switches have different numbers of ports and
MAC capabilities. Add .phylink_get_caps() to struct netc_switch_info,
allowing each NETC switch version to implement its own callback for
obtaining MAC capabilities.
Implement the phylink_mac_ops callbacks: .mac_config(), .mac_link_up(),
and .mac_link_down(). Note that flow-control configuration is not yet
supported in .mac_link_up(), but will be implemented in a subsequent
patch.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260518082506.1318236-12-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
For i.MX94 series, the NETC IP provides full 802.1Q Ethernet switch
functionality, advanced QoS with 8 traffic classes, and a full range of
TSN standards capabilities. The switch has 3 user ports and 1 CPU port,
the CPU port is connected to an internal ENETC. Since the switch and the
internal ENETC are fully integrated within the NETC IP, no back-to-back
MAC connection is required. Instead, a light-weight "pseudo MAC" is used
between the switch and the ENETC. This translates to lower power (less
logic and memory) and lower delay (as there is no serialization delay
across this link).
Introduce the initial NETC switch driver with basic probe and remove
functionality. More features will be added in subsequent patches.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260518082506.1318236-11-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
While being less compact, using named initializers allows to more easily
see which members of the structs are assigned which value without having
to lookup the declaration of the struct. And it's also more robust
against changes to the struct definition.
This patch doesn't modify the compiled arrays, only their representation
in source form benefits. The former was confirmed with x86 and arm64
builds.
While touching these arrays, unify usage of whitespace in the list
terminator.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260519145722.1590298-2-u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With bridge VLAN filtering enabled on a port configured as untagged
member of the bridge PVID, ingress untagged frames do not reach the
corresponding bridge VLAN upper interface (br-lan.<vid>). ARP and
similar traffic is visible on the physical port but not delivered
to the VLAN sub-interface.
The MT7530/MT7531 forwards frames to the CPU port with the user
port's PVID tag applied even when the frame ingressed untagged on
the wire, because the CPU port is set to MT7530_VLAN_EG_CONSISTENT
and is a tagged member of the VLAN entry created for the bridge
VLAN. The DSA core then sees a hwaccel-tagged frame whose VID
matches the port's PVID, which the bridge does not treat as the
untagged-on-the-wire frame that the user expects.
Set ds->untag_vlan_aware_bridge_pvid in the mt7530 and mt7531
setup paths so the DSA core strips that hwaccel tag in software
when the parsed VID matches the bridge port's PVID, restoring the
on-the-wire frame as the bridge expects to see it.
Link: https://github.com/openwrt/openwrt/issues/18576
Fixes: 83163f7dca ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: Edward Parker <edward@topnotchit.com>
[daniel@makrotopia.org: improve commit message]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/85d25ea1b26d3c907f815649f2e0bde6560282a3.1778766629.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
After a VLAN-aware bridge is destroyed, creating any VLAN-unaware
bridge loses all connectivity. The VID 0 VLAN table entry used by
VLAN-unaware ports in FALLBACK mode gets corrupted during VLAN-aware
operation: mt7530_hw_vlan_add() overwrites its EG_CON flag with
VTAG_EN and bridge teardown removes ports from its PORT_MEM.
The cleanup code that should restore it never runs because the current
port's dp->vlan_filtering flag is still true when checked (DSA updates
it only after the driver callback returns). Even when restored, the
deferred VLAN deletion events from the switchdev workqueue can corrupt
VID 0 again after the restoration.
Skip the current port in the all_user_ports_removed check, call
mt7530_setup_vlan0() to restore the VID 0 entry, and protect VID 0
from being modified by bridge VLAN operations in port_vlan_add and
port_vlan_del since it is managed exclusively by mt7530_setup_vlan0().
Remove the CPU port PCR and PVC register writes which were clobbering
PORT_VLAN mode and VLAN_ATTR with wrong values.
Fixes: 83163f7dca ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/da8bdaf08b2427a9057e6cb33e26d41f8a8d5000.1778766629.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The BPC, RGAC1 and RGAC2 registers control the handling of link-local
frames with reserved MAC DAs (01:80:C2:00:00:0x). These frames are
correctly trapped to the CPU port, but the egress VLAN tag attribute was
set to MT7530_VLAN_EG_UNTAGGED which causes the switch to strip any
VLAN tags from trapped frames before they reach the CPU.
This causes VLAN-tagged link-local frames (STP BPDUs, LLDP, PTP Peer
Delay Requests) to arrive at the CPU without their VLAN tag, so they
are delivered to the base network interface instead of the VLAN
sub-interface. The DSA local_termination selftest confirms this: all
link-local protocol tests on VLAN upper interfaces fail.
Set the EG_TAG attribute to MT7530_VLAN_EG_DISABLED (system default)
so that the switch does not modify VLAN tags in trapped frames. This
way VLAN-tagged frames retain their original tag and are delivered to
the correct VLAN sub-interface, matching the behavior of non-trapped
frames which pass through without VLAN tag modification.
Fixes: 69ddba9d17 ("net: dsa: mt7530: fix handling of all link-local frames")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/891e0cd34db2a5fe20ceb73283a81fb5f71427ca.1778766629.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The DSA forwarding selftests bridge_vlan_aware.sh and
bridge_vlan_unaware.sh configure the bridge with ageing_time set to
LOW_AGEING_TIME (1000 centiseconds, i.e. 10 seconds) and then run
learning_test() in lib.sh, which expects a learned FDB entry to be
removed after ageing_time + 10 seconds. On MT7530/MT7531 the entry
persisted past the deadline and the "Found FDB record when should
not" assertion failed.
With msecs=10000, the algorithm in mt7530_set_ageing_time() finds
AGE_CNT=0 and AGE_UNIT=9 as the first exact match (starting the
search from tmp_age_count=0). The per-entry aging counter is
initialized to AGE_CNT when a MAC address is learned, so with
AGE_CNT=0 new entries start with a counter value of 0, which the
hardware treats as "already aged" and never removes, effectively
disabling aging.
Fix this by starting the search from tmp_age_count=1 to ensure
entries always have a non-zero initial aging counter. For a
10-second ageing time this yields AGE_CNT=1 and AGE_UNIT=4 instead:
the timer ticks every 5 seconds and entries are removed after 2
ticks.
Starting the search at AGE_CNT=1 raises the minimum representable
ageing time from 1 to 2 seconds. Without bounds, a stale ageing_time
of 1 second would now make the loop fall through without setting
age_count and age_unit, leaving them uninitialized when written to
the MT7530_AAC hardware register. Set ds->ageing_time_min and
ds->ageing_time_max so the DSA core validates the range before the
callback is invoked, and drop the now-redundant range check from
mt7530_set_ageing_time().
Fixes: ea6d5c924e ("net: dsa: mt7530: support setting ageing time")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/7788ded12dc07b1bce329ec35fa70f4b45f3f9b7.1778766629.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ksz_phylink_get_caps() is a bit different from other generic methods.
It has a dev_ops->get_caps() call in the middle of the function, and it
does other stuff before (set some supported_interfaces) and after (set
lpi_interfaces from supported_interfaces).
Whereas the dev_ops->get_caps() methods set mac_capabilities and
(optionally) logically OR the supported_interfaces with that of the PCS.
The idea is that this can be expressed simpler, and avoid a indirect
function call to dev_ops->get_caps(). If we tail-call the common
ksz_phylink_get_caps() from individual phylink_get_caps() methods, we do
reorder the settings, but in an inconsequential way (the transfer from
supported_interfaces to lpi_interfaces still sees a complete list of the
supported_interfaces).
Remove the no longer used get_caps() callbacl the ksz_dev_ops.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260512-clean-ksz-2nd-series-v1-7-c00f6ce037fa@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mirror operations are handled through a common function that redirects
the treatment to ksz_dev_ops callbacks. This layer of indirection isn't
needed since we now have a dsa_switch_ops for each switch family.
Remove this indirection layer for KSZ switches, by connecting the
ksz_dev_ops :: mirror_add() and mirror_del() operations directly to
dsa_switch_ops.
Remove the now unused mirror callbacks from ksz_dev_ops.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260512-clean-ksz-2nd-series-v1-6-c00f6ce037fa@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
FDB and MDB operations are handled through a common function that
redirects the treatment to ksz_dev_ops callbacks. This layer of
indirection isn't needed since we now have a dsa_switch_ops for each kind
of switch.
Remove one indirection layer for KSZ switches, by connecting the
ksz_dev_ops :: fdb_dump(), fdb_add(), fdb_del(), mdb_add() and mdb_del()
operations directly to dsa_switch_ops.
Remove the FDB and MDB operations from ksz_dev_ops.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260512-clean-ksz-2nd-series-v1-5-c00f6ce037fa@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VLAN operations are handled through a common function that redirects the
treatment to ksz_dev_ops callbacks. This level of indirection isn't
needed since we now have a dsa_switch_ops for each kind of switch.
Remove this useless layer of indirection by connecting directly the VLAN
operations to the relevant dsa_switch_ops.
Adapt their prototypes to match dsa_switch_ops expectations.
Remove the now unused VLAN callbacks from ksz_dev_ops.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260512-clean-ksz-2nd-series-v1-4-c00f6ce037fa@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MTU changing is done through a common function that redirects the
treatment to a specific ksz_dev_ops callback. This layer of indirection
isn't needed since we now have a dsa_switch_ops struct for each switch
family.
Remove this indirection layer in MTU changing for KSZ switches, by
directly connecting the ksz_dev_ops :: change_mtu() implementations to
dsa_switch_ops.
Remove the no longer used change_mtu() callback from ksz_dev_ops
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260512-clean-ksz-2nd-series-v1-3-c00f6ce037fa@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dsa_switch_ops :: set_ageing_time() goes through ksz_set_ageing_time(),
further dispatched through ksz_dev_ops :: set_ageing_time(). Only
ksz9477 and lan937x provide an implementation for this, so remove the
(optional) method from ksz8463_switch_ops, ksz87xx_switch_ops,
ksz88xx_switch_ops. Also, hook up ksz9477 and lan937x dsa_switch_ops
directly to their respective implementations.
Every switch family provides a dsa_switch_ops :: port_fast_age()
implementation, which is dispatched through ksz_dev_ops ::
flush_dyn_mac_table(). Remove the dev_ops indirection and connect the
flush_dyn_mac_table() methods directly to their respective dsa_switch_ops.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260512-clean-ksz-2nd-series-v1-2-c00f6ce037fa@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add chip info entry for the Realtek RTL8367SB switch. This device has
chip ID 0x6367 and version 0x0010. It exposes two external interfaces:
port 6 supports MII, TMII, RMII, RGMII, SGMII and HSGMII, while port 7
supports MII, TMII, RMII and RGMII. Use the existing 8365MB-VC jam table
for initialization.
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://patch.msgid.link/3c6d822b-0e85-4173-86ba-2badb140bbf1@yahoo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All the KSZ switches use the same ksz_connect_tag_protocol while they
don't support all the KSZ tag protocols. So if, for some reason, a given
switch tries to connect another KSZ tag protocol, it won't fail.
Split the common ksz_connect_tag_protocol() into switch-specific
operations. This way, each switch will only accept to connect the tag
protocol it supports.
Remove the no longer used common operation.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260505-clean-ksz-driver-v1-9-05d70fa42461@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All the switch families use a common function to implement
.get_tag_protocol(). This function then returns the relevant protocol
depending on the chip ID.
Make the protocol to dsa_switch_ops association a little bit more
obvious by having separate implementations.
Change made by manually checking which chip id has which dsa_switch_ops
assigned to it, then filtering the common ksz_get_tag_protocol() for
just those chip IDs pertaining to it.
As an important benefit, we no longer have that weird-looking
DSA_TAG_PROTO_NONE fallback which was never actually returned.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260505-clean-ksz-driver-v1-8-05d70fa42461@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that each switch driver has its own dsa_switch_ops (currently a copy
of ksz_switch_ops), we no longer need ksz_switch_ops and can remove it.
Get to the driver-specific dsa_switch_ops through the ksz_chip_data
structure.
Reorder the alloc()/get_match_data() calls such as to have that
pointer available.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260505-clean-ksz-driver-v1-7-05d70fa42461@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently we have a single dsa_switch_ops for 4 very distinct families
of switches, and many dsa_switch_ops methods are simply a dispatches
through ksz_dev_ops. That creates an avoidable level of indirection.
As a preparation for removing that indirection layer, create a separate
dsa_switch_ops structure wherever we have a ksz_dev_ops. These
structures are not yet used - ksz_switch_ops from ksz_common.c still is.
However, this reduces the noise from subsequent changes.
All new dsa_switch_ops are exact copies of ksz_switch_ops. But we need
to export function prototypes from ksz_common.c so that they are
callable from individual drivers.
Note that "individual drivers" are not actual separate kernel modules.
All of ksz8.c, ksz9477.c and lan937x_main.c are part of the same
ksz_switch.ko. Only the "register interface" drivers are different
modules (ksz9477_i2c.o for I2C, ksz_spi.o for SPI, ksz8863_smi.o for
MDIO). So we don't need to export any symbol.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260505-clean-ksz-driver-v1-6-05d70fa42461@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similar to ksz_dev_ops, struct phylink_mac_ops shouldn't be part of
the common code. Instead, the common code should provide callable
functionality.
Invert the paradigm and export the common aspects from ksz_common.c, and
move the chip-specific stuff in individual drivers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260505-clean-ksz-driver-v1-5-05d70fa42461@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ksz_dev_ops() are specific to each switch family so they should
belong to the individual drivers instead of the common section.
Move the ksz_dev_ops() definitions of the KSZ9477 and the LAN937 to
their individual drivers.
Set static the functions that aren't exported anymore.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260505-clean-ksz-driver-v1-4-05d70fa42461@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ksz_dev_ops() are specific to each switch family so they should
belong to the individual drivers instead of the common section.
Move the ksz_dev_ops() definitions of the KSZ8xxx to ksz8.c
Set static the functions that aren't exported anymore.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260505-clean-ksz-driver-v1-3-05d70fa42461@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>