[ Upstream commit 45d5fe1c53 ]
Chips in the DA850 family need to have ARCH_DAVINCI_DA8XX to be selected
in order to enable some peripheral drivers.
This was accidentally removed in a previous commit.
Fixes: dec85a9516 ("ARM: davinci: clean up platform support")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c24f272ae7 ]
During upstream process of Raspberry Pi 4 back in 2019 the ARMv7 stubs
didn't configured the ARM architectural timer. This firmware issue has
been fixed in 2020, which gave users enough time to update their system.
So drop this property to allow the use of the vDSO version of
clock_gettime.
Link: https://github.com/raspberrypi/tools/pull/113
Fixes: 7dbe8c62ce ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250222094113.48198-1-wahrenst@gmx.net
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98f3ab18a0 ]
When GENERIC_IRQ_CHIP is disabled, OMAP1 kernels fail to link:
arm-linux-gnueabi-ld: arch/arm/mach-omap1/irq.o: in function `omap1_init_irq':
irq.c:(.init.text+0x1e8): undefined reference to `irq_alloc_generic_chip'
arm-linux-gnueabi-ld: irq.c:(.init.text+0x228): undefined reference to `irq_setup_generic_chip'
arm-linux-gnueabi-ld: irq.c:(.init.text+0x2a8): undefined reference to `irq_gc_set_wake'
arm-linux-gnueabi-ld: irq.c:(.init.text+0x2b0): undefined reference to `irq_gc_mask_set_bit'
arm-linux-gnueabi-ld: irq.c:(.init.text+0x2b4): undefined reference to `irq_gc_mask_clr_bit'
This has apparently been the case for many years, but I never caught it
in randconfig builds until now, as there are dozens of other drivers
that also 'select GENERIC_IRQ_CHIP' and statistically there is almost
always one of them enabled.
Fixes: 55b4477443 ("ARM: OMAP1: Switch to use generic irqchip in preparation for sparse IRQ")
Link: https://lore.kernel.org/r/20250205121151.289535-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0de09025f1 ]
The ARM PL011 UART instances in BCM2711 are r1p5 spec, which means they
have 32-entry FIFOs. The correct periphid value for this is 0x00341011.
Thanks to N Buchwitz for pointing this out.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20250223125614.3592-2-wahrenst@gmx.net
Fixes: 7dbe8c62ce ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0cfbd7805f upstream.
Despite CM_IDLEST1_CORE and CM_FCLKEN1_CORE behaving normal,
disabling SPI leads to messages like when suspending:
Powerdomain (core_pwrdm) didn't enter target state 0
and according to /sys/kernel/debug/pm_debug/count off state is not
entered. That was not connected to SPI during the discussion
of disabling SPI. See:
https://lore.kernel.org/linux-omap/20230122100852.32ae082c@aktux/
The reason is that SPI is per default in slave mode. Linux driver
will turn it to master per default. It slave mode, the powerdomain seems to
be kept active if active chip select input is sensed.
Fix that by explicitly disabling the SPI3 pins which used to be muxed by
the bootloader since they are available on an optionally fitted header
which would require dtb overlays anyways.
Fixes: a622310f7f ("ARM: dts: gta04: fix excess dma channel usage")
CC: stable@vger.kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241204174152.2360431-1-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1472ec1dc upstream.
A bus_dma_limit was added for l3 bus by commit cfb5d65f25
("ARM: dts: dra7: Add bus_dma_limit for L3 bus") to fix an issue
observed only with SATA on DRA7-EVM with 4GB RAM and CONFIG_ARM_LPAE
enabled.
Since kernel 5.13, the SATA issue can be reproduced again following
the SATA node move from L3 bus to L4_cfg in commit 8af15365a3
("ARM: dts: Configure interconnect target module for dra7 sata").
Fix it by adding an empty dma-ranges property to l4_cfg and
segment@100000 nodes (parent device tree node of SATA controller) to
inherit the 2GB dma ranges limit from l3 bus node.
Note: A similar fix was applied for PCIe controller by commit
90d4d3f4ea ("ARM: dts: dra7: Fix bus_dma_limit for PCIe").
Fixes: 8af15365a3 ("ARM: dts: Configure interconnect target module for dra7 sata").
Link: https://lore.kernel.org/linux-omap/c583e1bb-f56b-4489-8012-ce742e85f233@smile.fr/
Cc: stable@vger.kernel.org # 5.13
Signed-off-by: Romain Naour <romain.naour@skf.com>
Link: https://lore.kernel.org/r/20241115102537.1330300-1-romain.naour@smile.fr
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ad455e48bb ]
The Retu IRQ is off by one, as a result the power button does not work.
Fix it.
Fixes: 084b6f2167 ("ARM: omap1: Fix up the Nokia 770 board device IRQs")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/Z3UxH_fOzuftjnuX@darkstar.musicnaut.iki.fi
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d9e5965df ]
Add no-1-8-v property to sdmmc0 node to keep VDDSDMMC power rail at 3.3V.
This property will stop the LDO regulator from switching to 1.8V when the
MMC core detects an UHS SD Card. VDDSDMMC power rail is used by all the
SDMMC interface pins in GPIO mode (PA0 - PA13).
On this board, PA10 is used as GPIO to enable the power switch controlling
USB Vbus for the USB Host. The change is needed to fix the PA10 voltage
level to 3.3V instead of 1.8V.
Fixes: 5d4c3cfb63 ("ARM: dts: at91: sama5d27_wlsom1: add SAMA5D27 wlsom1 and wlsom1-ek")
Suggested-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Tested-by: Andrei Simion <andrei.simion@microchip.com>
Link: https://lore.kernel.org/r/20241119160107.598411-3-cristian.birsan@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a7f1848d9 ]
On board the sdmmc0 interface is wired to a SD Card socket.
According with mmc-controller bindings, the mmc-ddr-3_3v property
is used for eMMC devices to enable high-speed DDR mode (3.3V I/O).
Remove the mmc-ddr-3_3v property from sdmmc0 node.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Link: https://lore.kernel.org/r/20231204072537.2991-1-mihai.sain@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Stable-dep-of: 4d9e5965df ("ARM: dts: microchip: sama5d27_wlsom1_ek: Add no-1-8-v property to sdmmc0 node")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 479b8227ff ]
Swap USART3 and UART8 aliases on STM32MP15xx DHCOM SoM,
make sure UART8 is listed first, USART3 second, because
the UART8 is labeled as UART2 on the SoM pinout, while
USART3 is labeled as UART3 on the SoM pinout.
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73317d3271 ]
Deduplicate /aliases { serialN = ... } and /chosen node into
stm32mp15xx-dhcom-som.dtsi , since the content is identical
on all carrier boards using the STM32MP15xx DHCOM SoM. No
functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Stable-dep-of: 479b8227ff ("ARM: dts: stm32: Swap USART3 and UART8 alias on STM32MP15xx DHCOM SoM")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62a40a0d56 ]
The ahb reset is deasserted in probe before first register access, while the
stmmacheth-ocp reset needs to be asserted every time before changing the phy
mode in Arria10[1].
Changed in Upstream to "ahb"(331085a423b arm64: dts: socfpga: change the
reset-name of "stmmaceth-ocp" to "ahb" ).This change was intended for arm64
socfpga and it is not applicable to Arria10.
Further with STMMAC-SELFTEST Driver enabled, ethtool test also FAILS.
$ ethtool -t eth0
[ 322.946709] socfpga-dwmac ff800000.ethernet eth0: entered promiscuous mode
[ 323.374558] socfpga-dwmac ff800000.ethernet eth0: left promiscuous mode
The test result is FAIL
The test extra info:
1. MAC Loopback 0
2. PHY Loopback -110
3. MMC Counters -110
4. EEE -95
5. Hash Filter MC 0
6. Perfect Filter UC -110
7. MC Filter -110
8. UC Filter 0
9. Flow Control -110
10. RSS -95
11. VLAN Filtering -95
12. VLAN Filtering (perf) -95
13. Double VLAN Filter -95
14. Double VLAN Filter (perf) -95
15. Flexible RX Parser -95
16. SA Insertion (desc) -95
17. SA Replacement (desc) -95
18. SA Insertion (reg) -95
19. SA Replacement (reg) -95
20. VLAN TX Insertion -95
21. SVLAN TX Insertion -95
22. L3 DA Filtering -95
23. L3 SA Filtering -95
24. L4 DA TCP Filtering -95
25. L4 SA TCP Filtering -95
26. L4 DA UDP Filtering -95
27. L4 SA UDP Filtering -95
28. ARP Offload -95
29. Jumbo Frame -110
30. Multichannel Jumbo -95
31. Split Header -95
32. TBS (ETF Scheduler) -95
[ 324.881327] socfpga-dwmac ff800000.ethernet eth0: Link is Down
[ 327.995360] socfpga-dwmac ff800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Link:[1] https://www.intel.com/content/www/us/en/docs/programmable/683711/21-2/functional-description-of-the-emac.html
Fixes: 331085a423 ("arm64: dts: socfpga: change the reset-name of "stmmaceth-ocp" to "ahb")
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ea654242e ]
The GIC IRQ type used for IPCC RX should be IRQ_TYPE_LEVEL_HIGH.
Replacing the interrupt with the EXTI event changes the type to
the numeric value 1, meaning IRQ_TYPE_EDGE_RISING.
The issue is that EXTI event 61 is a direct event.The IRQ type of
direct events is not used by EXTI and is propagated to the parent
IRQ controller of EXTI, the GIC.
Align the IRQ type to the value expected by the GIC by replacing
the second parameter "1" with IRQ_TYPE_LEVEL_HIGH.
Fixes: 7d9802bb0e ("ARM: dts: stm32: remove the IPCC "wakeup" IRQ on stm32mp151")
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fc5bdfa87 ]
Change how the Backup Unit Power is configured and force the
automatic/hardware mode.
This change eliminates the need for software management of the power
switch, ensuring it transitions to the backup power source before
entering low power modes.
This is done in the only location where this switch was configured. It's
usually done in the bootloader.
Previously, the loss of the VDDANA (or VDDIN33) power source was not
automatically compensated by an alternative power source. This resulted
in the loss of Backup Unit content, including Backup Self-refresh low
power mode information, OTP emulation configuration, and boot
configuration, for instance.
Fixes: ac809e7879 ("ARM: at91: pm: switch backup area to vbat in backup mode")
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20241125165648.509162-1-nicolas.ferre@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 93ee385254 upstream.
The code for syncing vmalloc memory PGD pointers is using
atomic_read() in pair with atomic_set_release() but the
proper pairing is atomic_read_acquire() paired with
atomic_set_release().
This is done to clearly instruct the compiler to not
reorder the memcpy() or similar calls inside the section
so that we do not observe changes to init_mm. memcpy()
calls should be identified by the compiler as having
unpredictable side effects, but let's try to be on the
safe side.
Cc: stable@vger.kernel.org
Fixes: d31e23aff0 ("ARM: mm: make vmalloc_seq handling SMP safe")
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44e9a3bb76 upstream.
When switching task, in addition to a dummy read from the new
VMAP stack, also do a dummy read from the VMAP stack's
corresponding KASAN shadow memory to sync things up in
the new MM context.
Cc: stable@vger.kernel.org
Fixes: a1c510d0ad ("ARM: implement support for vmap'ed stacks")
Link: https://lore.kernel.org/linux-arm-kernel/a1a1d062-f3a2-4d05-9836-3b098de9db6d@foss.st.com/
Reported-by: Clement LE GOFFIC <clement.legoffic@foss.st.com>
Suggested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6e6a74d4c upstream.
When sync:ing the VMALLOC area to other CPUs, make sure to also
sync the KASAN shadow memory for the VMALLOC area, so that we
don't get stale entries for the shadow memory in the top level PGD.
Since we are now copying PGDs in two instances, create a helper
function named memcpy_pgd() to do the actual copying, and
create a helper to map the addresses of VMALLOC_START and
VMALLOC_END into the corresponding shadow memory.
Co-developed-by: Melon Liu <melon1335@163.com>
Cc: stable@vger.kernel.org
Fixes: 565cbaad83 ("ARM: 9202/1: kasan: support CONFIG_KASAN_VMALLOC")
Link: https://lore.kernel.org/linux-arm-kernel/a1a1d062-f3a2-4d05-9836-3b098de9db6d@foss.st.com/
Reported-by: Clement LE GOFFIC <clement.legoffic@foss.st.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96a64e9730 upstream.
Operating stable without reduced chip life at 1Ghz needs several
technologies working: The technologies involve
- SmartReflex
- DVFS
As this cannot directly specified in the OPP table as dependecies in the
devicetree yet, use the turbo flag again to mark this OPP as something
special to have some kind of opt-in.
So revert commit
5f1bf7ae84 ("ARM: dts: omap36xx: Remove turbo mode for 1GHz variants")
Practical reasoning:
At least the GTA04A5 (DM3730) has become unstable with that OPP enabled.
Furthermore nothing enforces the availability of said technologies,
even in the kernel configuration, so allow users to rather opt-in.
Cc: Stable@vger.kernel.org
Fixes: 5f1bf7ae84 ("ARM: dts: omap36xx: Remove turbo mode for 1GHz variants")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20241018214727.275162-1-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b2473a3597 ]
__pa() is only intended to be used for linear map addresses and using
it for initial_boot_params which is in fixmap for arm64 will give an
incorrect value. Hence save the physical address when it is known at
boot time when calling early_init_dt_scan for arm64 and use it at kexec
time instead of converting the virtual address using __pa().
Note that arm64 doesn't need the FDT region reserved in the DT as the
kernel explicitly reserves the passed in FDT. Therefore, only a debug
warning is fixed with this change.
Reported-by: Breno Leitao <leitao@debian.org>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Usama Arif <usamaarif642@gmail.com>
Fixes: ac10be5cdb ("arm64: Use common of_kexec_alloc_and_setup_fdt()")
Link: https://lore.kernel.org/r/20241023171426.452688-1-usamaarif642@gmail.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd36ad71ad ]
The DCDC5 voltage rail in the X-Powers AXP809 PMIC has a resolution of
50mV, so the currently enforced limits of 1.475 and 1.525 volts cannot
be set, when the existing regulator value is beyond this range.
This will lead to the whole regulator driver to give up and fail
probing, which in turn will hang the system, as essential devices depend
on the PMIC.
In this case a bug in U-Boot set the voltage to 1.75V (meant for DCDC4),
and the AXP driver's attempt to correct this lead to this error:
==================
[ 4.447653] axp20x-rsb sunxi-rsb-3a3: AXP20X driver loaded
[ 4.450066] vcc-dram: Bringing 1750000uV into 1575000-1575000uV
[ 4.460272] vcc-dram: failed to apply 1575000-1575000uV constraint: -EINVAL
[ 4.474788] axp20x-regulator axp20x-regulator.0: Failed to register dcdc5
[ 4.482276] axp20x-regulator axp20x-regulator.0: probe with driver axp20x-regulator failed with error -22
==================
Set the limits to values that can be programmed, so any correction will
be successful.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Fixes: 1e1dea7265 ("ARM: dts: sun9i: cubieboard4: Add AXP809 PMIC device node and regulators")
Link: https://patch.msgid.link/20241007222916.19013-1-andre.przywara@arm.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f9d013a0c ]
Add the atmel,usart-mode property to the UART nodes. This ensures
compliance with the atmel,at91-usart.yaml schema and resolves the errors
below:
serial@200: $nodename:0: 'serial@200' does not match
'^spi(@.*|-([0-9]|[1-9][0-9]+))?$'
serial@200: atmel,use-dma-rx: False schema does not allow True
serial@200: atmel,use-dma-tx: False schema does not allow True
serial@200: atmel,fifo-size: False schema does not allow [[16]]
These errors indicate that the property
atmel,usart-mode = <AT91_USART_MODE_SERIAL> is missing for
UART nodes 0, 1, 2, 3, 4, 6, 7, 8, 9, 10, 11, and 12.
Fixes: 99c8083358 ("ARM: dts: at91: sam9x60: Add missing flexcom definitions")
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Andrei Simion <andrei.simion@microchip.com>
Link: https://lore.kernel.org/r/20240912093307.40488-1-andrei.simion@microchip.com
[claudiu.beznea: move the atmel,usart-mode close to vendor specific
properties to cope with DTS coding style]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e9b0cf931 ]
Fix the physical address calculation of the following to get smp working
on xip kernels.
- secondary_data needed for secondary cpu bootup.
- secondary_startup address passed through psci.
- identity mapped code region needed for enabling mmu for secondary cpus.
Signed-off-by: Harith George <harith.g@alifsemi.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed6cbe6e55 ]
The patchset introducing kernel_sec_start/end variables to separate the
kernel/lowmem memory mappings, broke the mapping of the kernel memory
for xipkernels.
kernel_sec_start/end variables are in RO area before the MMU is switched
on for xipkernels.
So these cannot be set early in boot in head.S. Fix this by setting these
after MMU is switched on.
xipkernels need two different mappings for kernel text (starting at
CONFIG_XIP_PHYS_ADDR) and data (starting at CONFIG_PHYS_OFFSET).
Also, move the kernel code mapping from devicemaps_init() to map_kernel().
Fixes: a91da54570 ("ARM: 9089/1: Define kernel physical section start and end")
Signed-off-by: Harith George <harith.g@alifsemi.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77a9a7f2d3 ]
Both the node name as well as the compatible were not named
according to the binding expectations, fix that.
Fixes: 47bf3a5c9e ("ARM: dts: rockchip: add the sound setup for rk3036-kylin board")
Cc: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241008203940.2573684-15-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8bade1ad1f ]
Compatible and clock names did not match the existing binding.
So set the correct values and re-order+rename the clocks.
It looks like no rk3036 board did use the spi controller so far,
so this was never detected on a running device yet.
Fixes: f629fcfab2 ("ARM: dts: rockchip: support the spi for rk3036")
Cc: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241008203940.2573684-14-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1580ccb6ed ]
Neither the binding nor the driver implementation specify/use the grf
reference provided in the rk3036. And neither does the newer rk3128
user of the hdmi controller. So drop the rockchip,grf property.
Fixes: b7217cf19c ("ARM: dts: rockchip: add hdmi device node for rk3036")
Cc: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241008203940.2573684-13-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7206853cd ]
The acodec node is not conformant to the binding.
Set the correct nodename, use the correct compatible, add the needed
#sound-dai-cells and sort the rockchip,grf below clocks properties
as expected.
Fixes: faea098e18 ("ARM: dts: rockchip: add core rk3036 dtsi")
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241008203940.2573684-12-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c44d31cb3 ]
Algorithm registration is usually carried out during module init,
where as little work as possible should be carried out. The SIMD
code violated this rule by allocating a tfm, this then triggers a
full test of the algorithm which may dead-lock in certain cases.
SIMD is only allocating the tfm to get at the alg object, which is
in fact already available as it is what we are registering. Use
that directly and remove the crypto_alloc_tfm call.
Also remove some obsolete and unused SIMD API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1b0e32753d upstream.
The property is "fsl,pins", not "fsl,pin". Wrong property means the pin
configuration was not applied. Fixes dtbs_check warnings:
imx6ul-geam.dtb: pinctrl@20e0000: tscgrp: 'fsl,pins' is a required property
imx6ul-geam.dtb: pinctrl@20e0000: tscgrp: 'fsl,pin' does not match any of the regexes: 'pinctrl-[0-9]+'
Cc: stable@vger.kernel.org
Fixes: a58e4e608b ("ARM: dts: imx6ul-geam: Add Engicam IMX6UL GEA M6UL initial support")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c7f06284a6 ]
The psc->div[] array has psc->num_div elements. These values come from
when we call clk_hw_register_div(). It's adc_divisors and
ARRAY_SIZE(adc_divisors)) and so on. So this condition needs to be >=
instead of > to prevent an out of bounds read.
Fixes: 9645ccc7bd ("ep93xx: clock: convert in-place to COMMON_CLK")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Reviewed-by: Nikita Shubin <nikita.shubin@maquefel.me>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/1caf01ad4c0a8069535813c26c7f0b8ea011155e.camel@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e49cfe364 ]
There is no "fsl,phy" property in pin controller pincfg nodes:
imx7d-zii-rmu2.dtb: pinctrl@302c0000: enet1phyinterruptgrp: 'fsl,pins' is a required property
imx7d-zii-rmu2.dtb: pinctrl@302c0000: enet1phyinterruptgrp: 'fsl,phy' does not match any of the regexes: 'pinctrl-[0-9]+'
Fixes: f496e67500 ("ARM: dts: Add ZII support for ZII i.MX7 RMU2 board")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d355c895fa ]
The RTC and RTT peripherals use the timing domain slow clock (TD_SLCK),
sourced from the 32.768 kHz crystal oscillator or slow rc oscillator.
The previously used Monitoring domain slow clock (MD_SLCK) is sourced
from an internal RC oscillator which is most probably not precise enough
for real time clock purposes.
Fixes: 1e5f532c27 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Fixes: 5f6b33f463 ("ARM: dts: sam9x60: add rtt")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Link: https://lore.kernel.org/r/20240821055136.6858-1-ada@thorsis.com
[claudiu.beznea: removed () around the last commit description paragraph,
removed " in front of "timing domain slow clock", described that
TD_SLCK can also be sourced from slow rc oscillator]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit eba2591d99 upstream.
Instead of directly dereferencing page tables entries, which can cause
issues (see commit 20a004e7b0 ("arm64: mm: Use READ_ONCE/WRITE_ONCE when
accessing page tables"), let's introduce new functions to get the
pud/p4d/pgd entries (the pte and pmd versions already exist).
Note that arm pgd_t is actually an array so pgdp_get() is defined as a
macro to avoid a build error.
Those new functions will be used in subsequent commits by the riscv
architecture.
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20231213203001.179237-3-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5062d9c0cb ]
Negate the values reported for the accelerometer z-axis in order to
match Documentation/devicetree/bindings/iio/mount-matrix.txt.
Fixes: 14a213dcb0 ("ARM: dts: n900: use iio driver for accelerometer")
Signed-off-by: Sicelo A. Mhlongo <absicsz@gmail.com>
Reviewed-By: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20240722113137.3240847-1-absicsz@gmail.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8512fbb64b upstream.
On the imx6dl-yapp4 revision based boards, the RGB LED is not driven
directly by the LP5562 driver but through FET transistors. Hence the LED
current is not determined by the driver but by the LED series resistors.
On the imx6dl-yapp43 revision based boards, we removed the FET transistors
to drive the LED directly from the LP5562 but forgot to tune the output
current to match the previous HW design.
Set the LED current on imx6dl-yapp43 based boards to the same values
measured on the imx6dl-yapp4 boards and limit the maximum current to 20mA.
Fixes: 7da4734751 ("ARM: dts: imx6dl-yapp43: Add support for new HW revision of the IOTA board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4e7b4ff2dc ]
perf_callchain_store() return 0 on success, -1 otherwise, fix
callchain_trace() to return correct bool value. So walk_stackframe() can
have a chance to stop walking the stack ahead.
Fixes: 70ccc7c066 ("ARM: 9258/1: stacktrace: Make stack walk callback consistent with generic code")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78ab3d352f ]
GPIOs controlling backlight on Spitz and Akita are coming from GPIO
expanders, not the pxa27xx-gpio block, correct it.
Additionally GPIO lookup tables operate with pin numbers rather than
legacy GPIO numbers, fix that as well. Use raw numbers instead of legacy
GPIO names to avoid confusion.
Fixes: ee0c8e494c ("backlight: corgi: Convert to use GPIO descriptors")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20240628180852.1738922-2-dmitry.torokhov@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74e1c956a6 ]
There is a comment in the imx6q variant dtsi claiming that these
modules will have one more chip select than the imx6dl variant.
This is wrong. Ordinary GPIOs are used for chip selects and both
variants of the module share the very same PCB and both have this
GPIO routed to the SPI0_CS1# pin of the SMARC connector.
Fix it by moving the third chip select description to the common dtsi.
Fixes: 2125212785 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b972d6b3b4 ]
On i.MX6 the board is reset by the watchdog. But in turn to do a
complete board reset, we have to assert the WDOG_B output which is
routed also to the CPLD which then do a complete power-cycle of the
board.
Fixes: 2125212785 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edfea889a0 ]
The PHY reset line is connected to both the SoC (GPIO1_25) and
the CPLD. We must not use the GPIO1_25 as it will drive against
the output buffer of the CPLD. Instead there is another GPIO
(GPIO2_01), an input to the CPLD, which will tell the CPLD to
assert the PHY reset line.
Fixes: 2a51f9dae1 ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Fixes: 5694eed98c ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
