[ Upstream commit 9dfc46c87c ]
The current measured frame rate is 59.95Hz, which does not meet the
requirements of touch-stylus and stylus cannot work normally. After
adjustment, the actual measurement is 60.001Hz. Now this panel looks
like it's only used by me on the MTK platform, so let's change this
set of parameters.
[ dianders: Added "(again") to subject and fixed the "Fixes" line ]
Fixes: cea7008190 ("drm/panel: boe-tv101wum-nl6: Fine tune Himax83102-j02 panel HFP and HBP")
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240301061128.3145982-1-yangcong5@huaqin.corp-partner.google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6320b9199d ]
The mipi_dsi_dcs_nop() function returns an error but we weren't
checking it in boe_panel_prepare(). Add a check. This is highly
unlikely to matter in practice. If the NOP failed then likely later
MIPI commands would fail too.
Found by code inspection.
Fixes: 812562b8d8 ("drm/panel: boe-tv101wum-nl6: Fine tune the panel power sequence")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240517143643.3.Ibffbaa5b4999ac0e55f43bf353144433b099d727@changeid
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240517143643.3.Ibffbaa5b4999ac0e55f43bf353144433b099d727@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc2db2ef8d ]
If mipi_dsi_dcs_set_display_on() returned an error then we'd store
that in the "ret" variable and jump to error handling. We'd then
attempt an orderly poweroff. Unfortunately we then blew away the value
stored in "ret". That means that if the orderly poweroff actually
worked then we're return 0 (no error) from hx8394_enable() even though
the panel wasn't enabled.
Fix this by not blowing away "ret".
Found by code inspection.
Fixes: 65dc9360f7 ("drm: panel: Add Himax HX8394 panel controller driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240517143643.1.I0a6836fffd8d7620f353becb3df2370d2898f803@changeid
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240517143643.1.I0a6836fffd8d7620f353becb3df2370d2898f803@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11ac72d033 ]
The .bpc = 6 implies .bus_format = MEDIA_BUS_FMT_RGB666_1X7X3_SPWG ,
add the missing bus_format. Add missing connector type and bus_flags
as well.
Documentation [1] 1.4 GENERAL SPECIFICATI0NS indicates this panel is
capable of both RGB 18bit/24bit panel, the current configuration uses
18bit mode, .bus_format = MEDIA_BUS_FMT_RGB666_1X7X3_SPWG , .bpc = 6.
Support for the 24bit mode would require another entry in panel-simple
with .bus_format = MEDIA_BUS_FMT_RGB666_1X7X4_SPWG and .bpc = 8, which
is out of scope of this fix.
[1] https://www.distec.de/fileadmin/pdf/produkte/TFT-Displays/Innolux/G121X1-L03_Datasheet.pdf
Fixes: f8fa17ba81 ("drm/panel: simple: Add support for Innolux G121X1-L03")
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240328102746.17868-2-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ff5505b9a ]
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 623a3531e9 ("drm/panel: Add driver for Novatek NT35950 DSI DriverIC panels")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-8-619a28148e5c@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e842d55ba ]
When the atna33xc20 driver was first written the resume code never
returned an error. If there was a problem waiting for HPD it just
printed a warning and moved on. This changed in response to review
feedback [1] on a future patch but I accidentally didn't account for
rolling back the regulator enable in the error cases. Do so now.
[1] https://lore.kernel.org/all/5f3cf3a6-1cc2-63e4-f76b-4ee686764705@linaro.org/
Fixes: 3b5765df37 ("drm/panel: atna33xc20: Take advantage of wait_hpd_asserted() in struct drm_dp_aux")
Acked-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240313-homestarpanel-regulator-v1-1-b8e3a336da12@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8df1ddb5bf ]
If an eDP panel is not powered on then any attempts to talk to it over
the DP AUX channel will timeout. Unfortunately these attempts may be
quite slow. Userspace can initiate these attempts either via a
/dev/drm_dp_auxN device or via the created i2c device.
Making the DP AUX drivers timeout faster is a difficult proposition.
In theory we could just poll the panel's HPD line in the AUX transfer
function and immediately return an error there. However, this is
easier said than done. For one thing, there's no hard requirement to
hook the HPD line up for eDP panels and it's OK to just delay a fixed
amount. For another thing, the HPD line may not be fast to probe. On
parade-ps8640 we need to wait for the bridge chip's firmware to boot
before we can get the HPD line and this is a slow process.
The fact that the transfers are taking so long to timeout is causing
real problems. The open source fwupd daemon sometimes scans DP busses
looking for devices whose firmware need updating. If it happens to
scan while a panel is turned off this scan can take a long time. The
fwupd daemon could try to be smarter and only scan when eDP panels are
turned on, but we can also improve the behavior in the kernel.
Let's let eDP panels drivers specify that a panel is turned off and
then modify the common AUX transfer code not to attempt a transfer in
this case.
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Eizan Miyamoto <eizan@chromium.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202141109.1.I24277520ac754ea538c9b14578edc94e1df11b48@changeid
Stable-dep-of: 5e842d55ba ("drm/panel: atna33xc20: Fix unbalanced regulator in the case HPD doesn't assert")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da85f0aaa9 ]
In one case the -1 is returned which is quite confusing code for
the wrong device ID, in another the ret is returning instead of
plain 0 that also confusing as readed may ask the possible meaning
of positive codes, which are never the case there. Convert both
to use explicit predefined error codes to make it clear what's going
on there.
Fixes: 5a04227326 ("drm/panel: Add ilitek ili9341 panel driver")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Link: https://lore.kernel.org/r/20240425142706.2440113-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240425142706.2440113-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 740fc1e050 ]
GPIO controller might not be available when driver is being probed.
There are plenty of reasons why, one of which is deferred probe.
Since GPIOs are optional, return any error code we got to the upper
layer, including deferred probe. With that in mind, use dev_err_probe()
in order to avoid spamming the logs.
Fixes: 5a04227326 ("drm/panel: Add ilitek ili9341 panel driver")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Link: https://lore.kernel.org/r/20240425142706.2440113-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240425142706.2440113-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e4d3f4f34 ]
The DSI device for the panel was registered by the DSI host, so it is an
error to unregister it from the panel driver. Drop the call to
mipi_dsi_device_unregister().
Fixes: c7f66d32dd ("drm/panel: add support for rm69299 visionox panel")
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404-drop-panel-unregister-v1-1-9f56953c5fb9@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49ddab0896 ]
Some edp panel requires T10 (Delay from end of valid video data transmitted
by the Source device to power-off) less than 500ms. Using autosuspend with
delay set as 1000 violates this requirement.
Use put_sync_suspend in unprepare to meet the spec. For other cases (such
as getting EDID), it still uses autosuspend.
Suggested-by: Douglas Anderson <dianders@chromium.org>
Fixes: 3235b0f20a ("drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231220221418.2610185-1-hsinyi@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f7843b515 ]
Generic edp gets mode from edid. However, some panels report incorrect
mode in this way, resulting in glitches on panel. Introduce a new quirk
additional_mode to the generic edid to pick a correct hardcoded mode.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231117215056.1883314-2-hsinyi@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc6e767929 ]
Rename AUO 0x405c B116XAK01 to B116XAK01.0 and adjust the timing of
auo_b116xak01: T3=200, T12=500, T7_max = 50 according to decoding edid
and datasheet.
Fixes: da458286a5 ("drm/panel: Add support for AUO B116XAK01 panel")
Cc: stable@vger.kernel.org
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231107204611.3082200-2-hsinyi@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 799825aa87 ]
The AVCL register, according to the datasheet, comes in increments
of -0.2v between -4.4v (represented by 0x0) to -5.0v (represented
by 0x3). The current calculation is done by adding the defined
AVCL value in mV to -4400 and then dividing by 200 to get the register
value. Unfortunately if I subtract -4400 from -4400 I get -8800, which
divided by 200 gives me -44. If I instead subtract -4400 from -4400
I get 0, which divided by 200 gives me 0. Based on the datasheet this
is the expected register value.
Fixes: 83b7a8e7e8 ("drm/panel/panel-sitronix-st7701: Parametrize voltage and timing")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231208154847.130615-2-macroalpha82@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231208154847.130615-2-macroalpha82@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03c5b2a5f6 ]
For devices like the Anbernic RG351M and RG351P the panel is wired to
an always on regulator. When the device suspends and wakes up, there
are some slight artifacts on the screen that go away over time. If
instead we hold the panel in reset status after it is unprepared,
this does not happen.
Fixes: 5b6603360c ("drm/panel: add panel driver for Elida KD35T133 panels")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Link: https://lore.kernel.org/r/20231117194405.1386265-3-macroalpha82@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231117194405.1386265-3-macroalpha82@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cea7008190 ]
The refresh reported by modetest is 60.46Hz, and the actual measurement
is 60.01Hz, which is outside the expected tolerance. Adjust hporch and
pixel clock to fix it. After repair, modetest and actual measurement were
all 60.01Hz.
Modetest refresh = Pixel CLK/ htotal* vtotal, but measurement frame rate
is HS->LP cycle time(Vblanking). Measured frame rate is not only affecte
by Htotal/Vtotal/pixel clock, also affected by Lane-num/PixelBit/LineTime
/DSI CLK. Assume that the DSI controller could not make the mode that we
requested(presumably it's PLL couldn't generate the exact pixel clock?).
If you use a different DSI controller, you may need to readjust these
parameters. Now this panel looks like it's only used by me on the MTK
platform, so let's change this set of parameters.
Fixes: 1bc2ef065f ("drm/panel: Support for Starry-himax83102-j02 TDDI MIPI-DSI panel")
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231120020109.3216343-1-yangcong5@huaqin.corp-partner.google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f9a91b6c0 ]
The Innolux G101ICE-L01 datasheet [1] page 17 table
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
indicates that maximum vertical blanking time is 40 lines.
Currently the driver uses 29 lines.
Fix it, and since this panel is a DE panel, adjust the timings
to make them less hostile to controllers which cannot do 1 px
HSA/VSA, distribute the delays evenly between all three parts.
[1] https://www.data-modul.com/sites/default/files/products/G101ICE-L01-C2-specification-12042389.pdf
Fixes: 1e29b840af ("drm/panel: simple: Add Innolux G101ICE-L01 panel")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231008223256.279196-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06fc41b09c ]
Add missing .bus_flags = DRM_BUS_FLAG_DE_HIGH to this panel description,
ones which match both the datasheet and the panel display_timing flags .
Fixes: 1e29b840af ("drm/panel: simple: Add Innolux G101ICE-L01 panel")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231008223315.279215-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6965809e52 ]
For "auo,b101uan08.3" this panel, it is stipulated in the panel spec that
MIPI needs to keep the LP11 state before the lcm_reset pin is pulled high.
Fixes: 56ad624b4c ("drm/panel: support for auo, b101uan08.3 wuxga dsi video mode panel")
Signed-off-by: Xuxin Xiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231114044205.613421-1-xuxinxiong@huaqin.corp-partner.google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d12d635bb0 ]
Switching to a different reset sequence, enabling IOVCC before enabling
VCC.
There also needs to be a delay after enabling the supplies and before
deasserting the reset. The datasheet specifies 1ms after the supplies
reach the required voltage. Use 10-20ms to also give the power supplies
some time to reach the required voltage, too.
This fixes intermittent panel initialization failures and screen
corruption during resume from sleep on panel xingbangda,xbd599 (e.g.
used in PinePhone).
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Reported-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230211171748.36692-2-frank@oltmanns.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>
In commit 5f04e7ce39 ("drm/panel-edp: Split eDP panels out of
panel-simple") I moved a pile of panels out of panel-simple driver
into the newly created panel-edp driver. One of those panels, however,
shouldn't have been moved.
As is clear from commit e35e305eff ("drm/panel: simple: Add AUO
B116XW03 panel support"), AUX B116XW03 is an LVDS panel. It's used in
exynos5250-snow and exynos5420-peach-pit where it's clear that the
panel is hooked up with LVDS. Furthermore, searching for datasheets I
found one that makes it clear that this panel is LVDS.
As far as I can tell, I got confused because in commit 88d3457ceb
("drm/panel: auo,b116xw03: fix flash backlight when power on") Jitao
Shi added "DRM_MODE_CONNECTOR_eDP". That seems wrong. Looking at the
downstream ChromeOS trees, it seems like some Mediatek boards are
using a panel that they call "auo,b116xw03" that's an eDP panel. The
best I can guess is that they actually have a different panel that has
similar timing. If so then the proper panel should be used or they
should switch to the generic "edp-panel" compatible.
When moving this back to panel-edp, I wasn't sure what to use for
.bus_flags and .bus_format and whether to add the extra "enable" delay
from commit 88d3457ceb ("drm/panel: auo,b116xw03: fix flash
backlight when power on"). I've added formats/flags/delays based on my
(inexpert) analysis of the datasheet. These are untested.
NOTE: if/when this is backported to stable, we might run into some
trouble. Specifically, before 474c162878 ("arm64: dts: mt8183:
jacuzzi: Move panel under aux-bus") this panel was used by
"mt8183-kukui-jacuzzi", which assumed it was an eDP panel. I don't
know what to suggest for that other than someone making up a bogus
panel for jacuzzi that's just for the stable channel.
Fixes: 88d3457ceb ("drm/panel: auo,b116xw03: fix flash backlight when power on")
Fixes: 5f04e7ce39 ("drm/panel-edp: Split eDP panels out of panel-simple")
Tested-by: Anton Bambura <jenneron@postmarketos.org>
Acked-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230925150010.1.Iff672233861bcc4cf25a7ad0a81308adc3bda8a4@changeid
The sta_himax83102 panel sometimes shows abnormally flickering
horizontal lines. The front gate output will precharge the X point of
the next pole circuit before TP(TouchPanel Enable) term starts, and wait
until the end of the TP term to resume the CLK. For this reason, the X
point must be maintained during the TP term. In abnormal case, we
measured a slight leakage at point X. This because during the TP term,
the GPW does not fully pull the VGL low, causing the TFT to not be
closed tightly.
To fix this, we completely pull GPW to VGL before entering the TP term.
This will ensure that the TFT is closed tightly and prevent the abnormal
display.
Fixes: 1bc2ef065f ("drm/panel: Support for Starry-himax83102-j02 TDDI MIPI-DSI panel")
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231007064949.22668-1-zhouruihai@huaqin.corp-partner.google.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231007064949.22668-1-zhouruihai@huaqin.corp-partner.google.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmTiDvweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG7doH/2Poj73npPKPVfT3
RF8AsgvAj2pLby67rdvwTdFX+exS63SsuwtGGRfAHfGabiwmNN+oT2dLb0aY15bp
nskHnFpcqQ/pfZ2i2rUCenzBX8S9QULvPidLKRaf1FcSdOzqd97Bw5oDPMtzqy/R
Pm+Dzs//7fYvtm69nt6hKW4d6wXxNcg7Fk/QgoJ5Ax9vGvDuZmWXH0ZgBf/5kH04
TTPQNtVX57lf+FHugkhFEn4JbYXvN168b+LuX2PHwOeG/8AIS69Hc0vgvhHNAycT
mmpUI1gWA2jfrJ2RCyyezF/6wy9Ocsp+CbPjfwjuRUxOk0XIm1+cp9Mlz/cRbMsZ
f0tOTpk=
=xrJp
-----END PGP SIGNATURE-----
BackMerge tag 'v6.5-rc7' into drm-next
Linux 6.5-rc7
This is needed for the CI stuff and the msm pull has fixes in it.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This panel has been implemented in commit eae7488814 ("drm/panel-simple:
Add Innolux G156HCE-L01 panel entry") with a higher clock than the typical
one mentioned on the documentation to avoid flickering on the unit
tested. Testing on a different unit shows that the panel actually works
with the intended 70.93 MHz clock and even lower frequencies so the
flickering is likely caused either by a defective unit or by other
different components such as the bridge.
Fixes: eae7488814 ("drm/panel-simple: Add Innolux G156HCE-L01 panel entry")
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Marek Vasut <marex@denx.de> # MX8MM with LT9211
Reviewed-by: Marek Vasut <marex@denx.de>
[narmstrong: fixed commit id in commit msg]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230814134024.397739-1-luca.ceresoli@bootlin.com
Commit 03e909acd9 ("drm/panel: simple: Add support for AUO G121EAN01.4
panel") added support for this panel model, but the timings it implements
are very different from what the datasheet describes. I checked both the
G121EAN01.0 datasheet from [0] and the G121EAN01.4 one from [1] and they
all have the same timings: for example the LVDS clock typical value is 74.4
MHz, not 66.7 MHz as implemented.
Replace the timings with the ones from the documentation. These timings
have been tested and the clock frequencies verified with an oscilloscope to
ensure they are correct.
Also use struct display_timing instead of struct drm_display_mode in order
to also specify the minimum and maximum values.
[0] https://embedded.avnet.com/product/g121ean01-0/
[1] https://embedded.avnet.com/product/g121ean01-4/
Fixes: 03e909acd9 ("drm/panel: simple: Add support for AUO G121EAN01.4 panel")
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804151239.835216-1-luca.ceresoli@bootlin.com
Use the dev_err_probe() helper to simplify error handling during probe.
This also handle scenario, when EDEFER is returned and useless error is printed.
Fixes error:
panel-jdi-lt070me05000 4700000.dsi.0: cannot get enable-gpio -517
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230812185239.378582-1-david@ixit.cz
The Jasonic JT240MHQS-HWT-EK-E3 is a custom panel using the Sitronix
ST7789V controller. While the controller features a resolution of
320x240, only an area of 280x240 is visible by design.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230718-feature-lcd-panel-v2-4-2485ca07b49d@wolfvision.net
The ST7789V controller features support for the partial mode. Here,
the area to be displayed can be restricted in one direction (by default,
in vertical direction). This is useful for panels that are partially
occluded by design. Add support for the partial mode.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230718-feature-lcd-panel-v2-3-2485ca07b49d@wolfvision.net
Determine the orientation of the display based on the device tree and
propagate it.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230718-feature-st7789v-v3-2-157d68fb63e2@wolfvision.net
