commit 269e31aecd upstream.
There was a change in the mxs-dma engine that uses a new custom flag.
The change was not applied to the mxs spi driver.
This results in chipselect being deasserted too early.
This fixes the chipselect problem by using the new flag in the mxs-spi
driver.
Fixes: ceeeb99cd8 ("dmaengine: mxs: rename custom flag")
Signed-off-by: Ralf Schlatterbeck <rsc@runtux.com>
Link: https://msgid.link/r/20240202115330.wxkbfmvd76sy3a6a@runtux.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3588b1c0fd ]
When there is no dummy cycle in the spi-nor commands, both dummy bus cycle
bytes and width are zero. Because of the cpu's warning when divided by
zero, the warning should be avoided. Return just zero to avoid such
calculations.
Fixes: 1b74dd64c8 ("spi: Add Socionext F_OSPI SPI flash controller driver")
Co-developed-by: Kohei Ito <ito.kohei@socionext.com>
Signed-off-by: Kohei Ito <ito.kohei@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://patch.msgid.link/20250206085747.3834148-1-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit be92ab2de0 upstream.
The QSPI peripheral control and status registers are
accessible via the SoC's APB bus, whereas MMIO transactions'
data travels on the AHB bus.
Microchip documentation and even sample code from Atmel
emphasises the need for a memory barrier before the first
MMIO transaction to the AHB-connected QSPI, and before the
last write to its registers via APB. This is achieved by
the following lines in `atmel_qspi_transfer()`:
/* Dummy read of QSPI_IFR to synchronize APB and AHB accesses */
(void)atmel_qspi_read(aq, QSPI_IFR);
However, the current documentation makes no mention to
synchronization requirements in the other direction, i.e.
after the last data written via AHB, and before the first
register access on APB.
In our case, we were facing an issue where the QSPI peripheral
would cease to send any new CSR (nCS Rise) interrupts,
leading to a timeout in `atmel_qspi_wait_for_completion()`
and ultimately this panic in higher levels:
ubi0 error: ubi_io_write: error -110 while writing 63108 bytes
to PEB 491:128, written 63104 bytes
After months of extensive research of the codebase, fiddling
around the debugger with kgdb, and back-and-forth with
Microchip, we came to the conclusion that the issue is
probably that the peripheral is still busy receiving on AHB
when the LASTXFER bit is written to its Control Register
on APB, therefore this write gets lost, and the peripheral
still thinks there is more data to come in the MMIO transfer.
This was first formulated when we noticed that doubling the
write() of QSPI_CR_LASTXFER seemed to solve the problem.
Ultimately, the solution is to introduce memory barriers
after the AHB-mapped MMIO transfers, to ensure ordering.
Fixes: d5433def31 ("mtd: spi-nor: atmel-quadspi: Add spi-mem support to atmel-quadspi")
Cc: Hari.PrasathGE@microchip.com
Cc: Mahesh.Abotula@microchip.com
Cc: Marco.Cardellini@microchip.com
Cc: stable@vger.kernel.org # c0a0203cf5: ("spi: atmel-quadspi: Create `atmel_qspi_ops`"...)
Cc: stable@vger.kernel.org # 6.x.y
Signed-off-by: Bence Csókás <csokas.bence@prolan.hu>
Link: https://patch.msgid.link/20241219091258.395187-1-csokas.bence@prolan.hu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0a0203cf5 upstream.
Refactor the code to introduce an ops struct, to prepare for merging
support for later SoCs, such as SAMA7G5. This code was based on the
vendor's kernel (linux4microchip). Cc'ing original contributors.
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Link: https://patch.msgid.link/20241128174316.3209354-2-csokas.bence@prolan.hu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a07eb4f67e ]
devm_clk_get_optional() returns NULL for missing clocks and a PTR_ERR()
if there is a clock but we fail to get it, but currently we only handle
the latter case and do so as though the clock was missing. If we get an
error back we should handle that as an error since the clock exists but
we failed to get it, if we get NULL then the clock doesn't exist and we
should handle that.
Fixes: 4c6ac5446d ("spi: omap2-mcspi: Fix the IS_ERR() bug for devm_clk_get_optional_enabled()")
Reported-by: Lars Pedersen <lapeddk@gmail.com>
Link: https://patch.msgid.link/20250117-spi-fix-omap2-optional-v1-1-e77d4ac6db6e@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Lars Pedersen <lapeddk@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8332e66709 ]
Add check for the return value of clk_enable() to catch the potential
error.
Fixes: c618a90dca ("spi: zynq-qspi: Drop GPIO header")
Signed-off-by: Mingwei Zheng <zmw12306@gmail.com>
Signed-off-by: Jiasheng Jiang <jiashengjiangcool@gmail.com>
Link: https://patch.msgid.link/20241207015206.3689364-1-zmw12306@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c6ac5446d ]
The devm_clk_get_optional_enabled() function returns error
pointers(PTR_ERR()). So use IS_ERR() to check it.
Verified on K3-J7200 EVM board, without clock node mentioned
in the device tree.
Signed-off-by: Purushothama Siddaiah <psiddaiah@mvista.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Link: https://patch.msgid.link/20241205070426.1861048-1-psiddaiah@mvista.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ceb259e43b ]
The Panther Lake SPI controllers are compatible with the Cannon Lake
controllers. Add support for following SPI controller device IDs:
- H-series: 0xe323
- P-series: 0xe423
- U-series: 0xe423
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://patch.msgid.link/20241204080208.1036537-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa8ecda987 ]
The target value of scldiv is just a byte, but its calculation in
fsl_lpspi_set_bitrate could be negative. So use an adequate type to store
the result and avoid overflows. After that this needs range check
adjustments, but this should make the code less opaque.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20240930093056.93418-2-wahrenst@gmx.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 984836621a ]
If we remove the module which will call mpc52xx_spi_remove
it will free 'ms' through spi_unregister_controller.
while the work ms->work will be used. The sequence of operations
that may lead to a UAF bug.
Fix it by ensuring that the work is canceled before proceeding with
the cleanup in mpc52xx_spi_remove.
Fixes: ca632f5566 ("spi: reorganize drivers")
Signed-off-by: Pei Xiao <xiaopei01@kylinos.cn>
Link: https://patch.msgid.link/1f16f8ae0e50ca9adb1dc849bf2ac65a40c9ceb9.1732783000.git.xiaopei01@kylinos.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d24cfee7f6 upstream.
When probing spi device take care of deferred probe of ACPI irq gpio
similar like for OF/DT case.
>From practical standpoint this fixes issue with vsc-tp driver on
Dell XP 9340 laptop, which try to request interrupt with spi->irq
equal to -EPROBE_DEFER and fail to probe with the following error:
vsc-tp spi-INTC10D0:00: probe with driver vsc-tp failed with error -22
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Fixes: 33ada67da3 ("ACPI / spi: attach GPIO IRQ from ACPI description to SPI device")
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Alexis Lothoré <alexis.lothore@bootlin.com> # Dell XPS9320, ov01a10
Link: https://patch.msgid.link/20241122094224.226773-1-stanislaw.gruszka@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ac40e6d0c ]
`atmel_qspi_reg_name()` is used for pretty-printing register offsets
for verbose logging of register accesses. However, due to a typo
(likely a copy-paste error), QSPI_RD's offset prints as "MR", the
name of the previous register. Fix this typo.
Fixes: c528ecfbef ("spi: atmel-quadspi: Add verbose debug facilities to monitor register accesses")
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
Link: https://patch.msgid.link/20241122141302.2599636-1-csokas.bence@prolan.hu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2219576883 ]
It's important to undo pm_runtime_use_autosuspend() with
pm_runtime_dont_use_autosuspend() at driver exit time.
So, call pm_runtime_dont_use_autosuspend() at driver exit time
to fix it.
Fixes: 9e3a000362 ("spi: zynqmp: Add pm runtime support")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240920091135.2741574-1-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f399051ec1 ]
A shift-out-of-bounds issue was identified by UBSAN in the
tegra_qspi_fill_tx_fifo_from_client_txbuf() function.
UBSAN: shift-out-of-bounds in drivers/spi/spi-tegra210-quad.c:345:27
shift exponent 32 is too large for 32-bit type 'u32' (aka 'unsigned int')
Call trace:
tegra_qspi_start_cpu_based_transfer
The problem arises when shifting the contents of tx_buf left by 8 times
the value of i, which can exceed 4 and result in an exponent larger than
32 bits.
Resolve this by restrict the value of i to be less than 4, preventing
the shift operation from overflowing.
Signed-off-by: Breno Leitao <leitao@debian.org>
Fixes: 921fc1838f ("spi: tegra210-quad: Add support for Tegra210 QSPI controller")
Link: https://patch.msgid.link/20241004125400.1791089-1-leitao@debian.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 003c7e0191 ]
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Fixes: 9728fb3ce1 ("spi: lpspi: disable lpspi module irq in DMA mode")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240906022828.891812-1-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bff892acf7 ]
devm_spi_alloc_controller will allocate an SPI controller and
automatically release a reference on it when dev is unbound from
its driver. It doesn't need to call spi_controller_put explicitly
to put the reference when lpspi driver failed initialization.
Fixes: 2ae0ab0143 ("spi: lpspi: Avoid potential use-after-free in probe()")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://msgid.link/r/20240403084029.2000544-1-carlos.song@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 265697288e upstream.
The pm_runtime_disable() is missing in the remove function, fix it
by using devm_pm_runtime_enable(), so the pm_runtime_disable() in
the probe error path can also be removed.
Fixes: 2d13f2ff60 ("spi: bcm63xx-spi: fix pm_runtime")
Cc: stable@vger.kernel.org # v5.13+
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://patch.msgid.link/20240819123349.4020472-3-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 909f34f246 upstream.
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from platform_device_id table.
Fixes: 44d8fb3094 ("spi/bcm63xx: move register definitions into the driver")
Cc: stable@vger.kernel.org
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://patch.msgid.link/20240819123349.4020472-2-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0880f66943 ]
Add missing MODULE_DEVICE_TABLE definition for automatic loading of the
driver when it is built as a module.
Fixes: eb8d6d464a ("spi: add Renesas RPC-IF driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20240731072955.224125-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68a16708d2 ]
In the s3c64xx_flush_fifo() code, the loops counter is post-decremented
in the do { } while(test && loops--) condition. This means the loops is
left at the unsigned equivalent of -1 if the loop times out. The test
after will never pass as if tests for loops == 0.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Fixes: 230d42d422 ("spi: Add s3c64xx SPI Controller driver")
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://patch.msgid.link/20240924134009.116247-2-ben.dooks@codethink.co.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3eae4a916f ]
The spi_controller_is_target() check is missing for pm_runtime_disable()
in cdns_spi_remove(), add it.
Fixes: b1b90514ea ("spi: spi-cadence: Add support for Slave mode")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240923040015.3009329-4-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67d4a70faa ]
It is not valid to call pm_runtime_set_suspended() for devices
with runtime PM enabled because it returns -EAGAIN if it is enabled
already and working. So, call pm_runtime_disable() before to fix it.
Fixes: d36ccd9f7e ("spi: cadence: Runtime pm adaptation")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240923040015.3009329-3-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f64b1600f9 ]
Since commit 7ef9651e97 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20230823133938.1359106-9-lizetao1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 67d4a70faa ("spi: spi-cadence: Fix pm_runtime_set_suspended() with runtime pm enabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6e05ba084 ]
It is not valid to call pm_runtime_set_suspended() for devices
with runtime PM enabled because it returns -EAGAIN if it is enabled
already and working. So, call pm_runtime_disable() before to fix it.
Fixes: 43b6bf406c ("spi: imx: fix runtime pm support for !CONFIG_PM")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240923040015.3009329-2-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9228956a62 upstream.
The flexspi on imx8ulp only has 16 LUTs, different with others which
have up to 32 LUTs.
Add a separate compatible string and nxp_fspi_devtype_data to support
flexspi on imx8ulp.
Fixes: ef89fd56bd ("arm64: dts: imx8ulp: add flexspi node")
Cc: stable@kernel.org
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20240905094338.1986871-4-haibo.chen@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 190b7e2efb upstream.
The flexspi on different SoCs may have different number of LUTs.
So involve lut_num in nxp_fspi_devtype_data to make distinguish.
This patch prepare for the adding of imx8ulp.
Fixes: ef89fd56bd ("arm64: dts: imx8ulp: add flexspi node")
Cc: stable@kernel.org
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20240905094338.1986871-3-haibo.chen@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 329ca3eed4 ]
Previously the MR and SCR registers were just set with the supposedly
required values, from cached register values (cached reg content
initialized to zero).
All parts fixed here did not consider the current register (cache)
content, which would make future support of cs_setup, cs_hold, and
cs_inactive impossible.
Setting SCBR in atmel_qspi_setup() erases a possible DLYBS setting from
atmel_qspi_set_cs_timing(). The DLYBS setting is applied by ORing over
the current setting, without resetting the bits first. All writes to MR
did not consider possible settings of DLYCS and DLYBCT.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Fixes: f732646d0c ("spi: atmel-quadspi: Add support for configuring CS timing")
Link: https://patch.msgid.link/20240918082744.379610-2-ada@thorsis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b577de206 ]
It's important to undo pm_runtime_use_autosuspend() with
pm_runtime_dont_use_autosuspend() at driver exit time unless driver
initially enabled pm_runtime with devm_pm_runtime_enable()
(which handles it for you).
Hence, call pm_runtime_dont_use_autosuspend() at driver exit time
to fix it.
Fixes: 944c01a889 ("spi: lpspi: enable runtime pm for lpspi")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240906021251.610462-1-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 438efb23f9 ]
It's important to undo pm_runtime_use_autosuspend() with
pm_runtime_dont_use_autosuspend() at driver exit time unless driver
initially enabled pm_runtime with devm_pm_runtime_enable()
(which handles it for you).
Hence, call pm_runtime_dont_use_autosuspend() at driver exit time
to fix it.
Fixes: 4a2f83b7f7 ("spi: atmel-quadspi: add runtime pm support")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240906023956.1004440-1-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4439a2e92c ]
The pm_runtime_disable() is missing in remove function, use
devm_pm_runtime_enable() to fix it. So the pm_runtime_disable() in
the probe error path can also be removed.
Fixes: a38a2233f2 ("spi: bcmbca-hsspi: Add driver for newer HSSPI controller")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Link: https://patch.msgid.link/20240826124903.3429235-2-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7781f1d120 ]
0 is incorrect error code when failed to parse and map IRQ.
Replace OF specific old API for IRQ retrieval with a generic
one to fix this issue.
Fixes: 0f245463b0 ("spi: ppc4xx: handle irq_of_parse_and_map() errors")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20240814144525.2648450-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f245463b0 ]
Zero and negative number is not a valid IRQ for in-kernel code and the
irq_of_parse_and_map() function returns zero on error. So this check for
valid IRQs should only accept values > 0.
Fixes: 44dab88e7c ("spi: add spi_ppc4xx driver")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Link: https://patch.msgid.link/20240724084047.1506084-1-make24@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5478a4f7b9 ]
When the of_device_id entry for "elgin,jg10309-01" was added, the
corresponding spi_device_id was forgotten, causing a warning message
during boot-up:
SPI driver spidev has no spi_device_id for elgin,jg10309-01
Fix module autoloading and shut up the warning by adding the missing
entry.
Fixes: 5f3eee1eef ("spi: spidev: Add an entry for elgin,jg10309-01")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/54bbb9d8a8db7e52d13e266f2d4a9bcd8b42a98a.1725366625.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 709df70a20 ]
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded based
on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Link: https://patch.msgid.link/20240831094231.795024-1-liaochen4@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f3eee1eef ]
The rv1108-elgin-r1 board has an LCD controlled via SPI in userspace.
The marking on the LCD is JG10309-01.
Add the "elgin,jg10309-01" compatible string.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240828180057.3167190-2-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b787a33864 ]
In spi_geni_remove(), the free_irq() sequence is different from that
on the probe error path. And the IRQ will still remain and it's interrupt
handler may use the dma channel after release dma channel and before free
irq, which is not secure, fix it.
Fixes: b59c122484 ("spi: spi-geni-qcom: Add support for GPI dma")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patch.msgid.link/20240909073141.951494-3-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89e362c883 ]
It's important to undo pm_runtime_use_autosuspend() with
pm_runtime_dont_use_autosuspend() at driver exit time unless driver
initially enabled pm_runtime with devm_pm_runtime_enable()
(which handles it for you).
Hence, switch to devm_pm_runtime_enable() to fix it, so the
pm_runtime_disable() in probe error path and remove function
can be removed.
Fixes: cfdab2cd85 ("spi: spi-geni-qcom: Set an autosuspend delay of 250 ms")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patch.msgid.link/20240909073141.951494-2-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2a8787c1cd upstream.
Change the memcpy length to fix the out-of-bounds issue when writing the
data that is not 4 byte aligned to TX FIFO.
To reproduce the issue, write 3 bytes data to NOR chip.
dd if=3b of=/dev/mtd0
[ 36.926103] ==================================================================
[ 36.933409] BUG: KASAN: slab-out-of-bounds in nxp_fspi_exec_op+0x26ec/0x2838
[ 36.940514] Read of size 4 at addr ffff00081037c2a0 by task dd/455
[ 36.946721]
[ 36.948235] CPU: 3 UID: 0 PID: 455 Comm: dd Not tainted 6.11.0-rc5-gc7b0e37c8434 #1070
[ 36.956185] Hardware name: Freescale i.MX8QM MEK (DT)
[ 36.961260] Call trace:
[ 36.963723] dump_backtrace+0x90/0xe8
[ 36.967414] show_stack+0x18/0x24
[ 36.970749] dump_stack_lvl+0x78/0x90
[ 36.974451] print_report+0x114/0x5cc
[ 36.978151] kasan_report+0xa4/0xf0
[ 36.981670] __asan_report_load_n_noabort+0x1c/0x28
[ 36.986587] nxp_fspi_exec_op+0x26ec/0x2838
[ 36.990800] spi_mem_exec_op+0x8ec/0xd30
[ 36.994762] spi_mem_no_dirmap_read+0x190/0x1e0
[ 36.999323] spi_mem_dirmap_write+0x238/0x32c
[ 37.003710] spi_nor_write_data+0x220/0x374
[ 37.007932] spi_nor_write+0x110/0x2e8
[ 37.011711] mtd_write_oob_std+0x154/0x1f0
[ 37.015838] mtd_write_oob+0x104/0x1d0
[ 37.019617] mtd_write+0xb8/0x12c
[ 37.022953] mtdchar_write+0x224/0x47c
[ 37.026732] vfs_write+0x1e4/0x8c8
[ 37.030163] ksys_write+0xec/0x1d0
[ 37.033586] __arm64_sys_write+0x6c/0x9c
[ 37.037539] invoke_syscall+0x6c/0x258
[ 37.041327] el0_svc_common.constprop.0+0x160/0x22c
[ 37.046244] do_el0_svc+0x44/0x5c
[ 37.049589] el0_svc+0x38/0x78
[ 37.052681] el0t_64_sync_handler+0x13c/0x158
[ 37.057077] el0t_64_sync+0x190/0x194
[ 37.060775]
[ 37.062274] Allocated by task 455:
[ 37.065701] kasan_save_stack+0x2c/0x54
[ 37.069570] kasan_save_track+0x20/0x3c
[ 37.073438] kasan_save_alloc_info+0x40/0x54
[ 37.077736] __kasan_kmalloc+0xa0/0xb8
[ 37.081515] __kmalloc_noprof+0x158/0x2f8
[ 37.085563] mtd_kmalloc_up_to+0x120/0x154
[ 37.089690] mtdchar_write+0x130/0x47c
[ 37.093469] vfs_write+0x1e4/0x8c8
[ 37.096901] ksys_write+0xec/0x1d0
[ 37.100332] __arm64_sys_write+0x6c/0x9c
[ 37.104287] invoke_syscall+0x6c/0x258
[ 37.108064] el0_svc_common.constprop.0+0x160/0x22c
[ 37.112972] do_el0_svc+0x44/0x5c
[ 37.116319] el0_svc+0x38/0x78
[ 37.119401] el0t_64_sync_handler+0x13c/0x158
[ 37.123788] el0t_64_sync+0x190/0x194
[ 37.127474]
[ 37.128977] The buggy address belongs to the object at ffff00081037c2a0
[ 37.128977] which belongs to the cache kmalloc-8 of size 8
[ 37.141177] The buggy address is located 0 bytes inside of
[ 37.141177] allocated 3-byte region [ffff00081037c2a0, ffff00081037c2a3)
[ 37.153465]
[ 37.154971] The buggy address belongs to the physical page:
[ 37.160559] page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x89037c
[ 37.168596] flags: 0xbfffe0000000000(node=0|zone=2|lastcpupid=0x1ffff)
[ 37.175149] page_type: 0xfdffffff(slab)
[ 37.179021] raw: 0bfffe0000000000 ffff000800002500 dead000000000122 0000000000000000
[ 37.186788] raw: 0000000000000000 0000000080800080 00000001fdffffff 0000000000000000
[ 37.194553] page dumped because: kasan: bad access detected
[ 37.200144]
[ 37.201647] Memory state around the buggy address:
[ 37.206460] ffff00081037c180: fa fc fc fc fa fc fc fc fa fc fc fc fa fc fc fc
[ 37.213701] ffff00081037c200: fa fc fc fc 05 fc fc fc 03 fc fc fc 02 fc fc fc
[ 37.220946] >ffff00081037c280: 06 fc fc fc 03 fc fc fc fc fc fc fc fc fc fc fc
[ 37.228186] ^
[ 37.232473] ffff00081037c300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 37.239718] ffff00081037c380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 37.246962] ==================================================================
[ 37.254394] Disabling lock debugging due to kernel taint
0+1 records in
0+1 records out
3 bytes copied, 0.335911 s, 0.0 kB/s
Fixes: a5356aef6a ("spi: spi-mem: Add driver for NXP FlexSPI controller")
Cc: stable@kernel.org
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://patch.msgid.link/20240911211146.3337068-1-han.xu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff949d981c upstream.
The commit 783bf5d09f ("spi: spi-fsl-lpspi: limit PRESCALE bit in
TCR register") doesn't implement the prescaler maximum as intended.
The maximum allowed value for i.MX93 should be 1 and for i.MX7ULP
it should be 7. So this needs also a adjustment of the comparison
in the scldiv calculation.
Fixes: 783bf5d09f ("spi: spi-fsl-lpspi: limit PRESCALE bit in TCR register")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20240905111537.90389-1-wahrenst@gmx.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 783bf5d09f ]
Referring to the errata ERR051608 of I.MX93, LPSPI TCR[PRESCALE]
can only be configured to be 0 or 1, other values are not valid
and will cause LPSPI to not work.
Add the prescale limitation for LPSPI in I.MX93. Other platforms
are not affected.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://patch.msgid.link/20240820070658.672127-1-carlos.song@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5127c42c77 ]
If the value of max_speed_hz is 0, it may cause a division by zero
error in hisi_calc_effective_speed().
The value of max_speed_hz is provided by firmware.
Firmware is generally considered as a trusted domain. However, as
division by zero errors can cause system failure, for defense measure,
the value of max_speed is validated here. So 0 is regarded as invalid
and an error code is returned.
Signed-off-by: Devyn Liu <liudingyuan@huawei.com>
Reviewed-by: Jay Fang <f.fangjian@huawei.com>
Link: https://patch.msgid.link/20240730032040.3156393-3-liudingyuan@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit be721b451a upstream.
Commit e882575efc ("spi: rockchip: Suspend and resume the bus during
NOIRQ_SYSTEM_SLEEP_PM ops") stopped respecting runtime PM status and
simply disabled clocks unconditionally when suspending the system. This
causes problems when the device is already runtime suspended when we go
to sleep -- in which case we double-disable clocks and produce a
WARNing.
Switch back to pm_runtime_force_{suspend,resume}(), because that still
seems like the right thing to do, and the aforementioned commit makes no
explanation why it stopped using it.
Also, refactor some of the resume() error handling, because it's not
actually a good idea to re-disable clocks on failure.
Fixes: e882575efc ("spi: rockchip: Suspend and resume the bus during NOIRQ_SYSTEM_SLEEP_PM ops")
Cc: stable@vger.kernel.org
Reported-by: Ondřej Jirman <megi@xff.cz>
Closes: https://lore.kernel.org/lkml/20220621154218.sau54jeij4bunf56@core/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://patch.msgid.link/20240827171126.1115748-1-briannorris@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c3c4f22b7c ]
The speed specified by the user is used to calculate the clk_div based
on the max_speed_hz in hisi_calc_effective_speed. A very low speed
value can lead to a clk_div larger than the variable range. Avoid this
by setting the min_speed_hz so that such a small speed value is
rejected. __spi_validate() in spi.c will return -EINVAL for the
specified speed_hz lower than min_speed_hz.
Signed-off-by: Devyn Liu <liudingyuan@huawei.com>
Reviewed-by: Jay Fang <f.fangjian@huawei.com>
Link: https://patch.msgid.link/20240730032040.3156393-2-liudingyuan@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 730bbfaf7d ]
The effective SPI clock frequency should never exceed speed_hz
otherwise this might result in undefined behavior of the SPI device.
Currently the scldiv calculation could violate this constraint.
For the example parameters perclk_rate = 24 MHz and speed_hz = 7 MHz,
the function fsl_lpspi_set_bitrate will determine perscale = 0 and
scldiv = 1, which is a effective SPI clock of 8 MHz.
So fix this by rounding up the quotient of perclk_rate and speed_hz.
While this never change within the loop, we can pull this out.
Fixes: 5314987de5 ("spi: imx: add lpspi bus driver")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20240804113611.83613-1-wahrenst@gmx.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4c4638b6a ]
When the of_device_id entry for "rohm,bh2228fv" was added, the
corresponding spi_device_id was forgotten, causing a warning message
during boot-up:
SPI driver spidev has no spi_device_id for rohm,bh2228fv
Fix module autoloading and shut up the warning by adding the missing
entry.
Fixes: fc28d1c1fe ("spi: spidev: add correct compatible for Rohm BH2228FV")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/cb571d4128f41175f31319cd9febc829417ea167.1722346539.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc28d1c1fe ]
When Maxime originally added the BH2228FV to the spidev driver, he spelt
it incorrectly - the d should have been a b. Add the correctly spelt
compatible to the driver. Although the majority of users of this
compatible are abusers, there is at least one board that validly uses
the incorrect spelt compatible, so keep it in the driver to avoid
breaking the few real users it has.
Fixes: 8fad805bdc ("spi: spidev: Add Rohm DH2228FV DAC compatible string")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20240717-ventricle-strewn-a7678c509e85@spud
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
