To install a livepatch, first flash the package to NVM, and then
activate the patch through the "HWRM_FW_LIVEPATCH" fw command.
To uninstall a patch from NVM, flash the removal package and then
activate it through the "HWRM_FW_LIVEPATCH" fw command.
The "HWRM_FW_LIVEPATCH" fw command has to consider following scenarios:
1. no patch in NVM and no patch active. Do nothing.
2. patch in NVM, but not active. Activate the patch currently in NVM.
3. patch is not in NVM, but active. Deactivate the patch.
4. patch in NVM and the patch active. Do nothing.
Fix the code to handle these scenarios during devlink "fw_activate".
To install and activate a live patch:
devlink dev flash pci/0000:c1:00.0 file thor_patch.pkg
devlink -f dev reload pci/0000:c1:00.0 action fw_activate limit no_reset
To remove and deactivate a live patch:
devlink dev flash pci/0000:c1:00.0 file thor_patch_rem.pkg
devlink -f dev reload pci/0000:c1:00.0 action fw_activate limit no_reset
Fixes: 3c4153394e ("bnxt_en: implement firmware live patching")
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When polling for the firmware message response, we first poll for the
response message header. Once the valid length is detected in the
header, we poll for the valid bit at the end of the message which
signals DMA completion. Normally, this poll time for DMA completion
is extremely short (0 to a few usec). But on some devices under some
rare conditions, it can be up to about 20 msec.
Increase this delay to 50 msec and use udelay() for the first 10 usec
for the common case, and usleep_range() beyond that.
Also, change the error message to include the above delay time when
printing the timeout value.
Fixes: 3c8c20db76 ("bnxt_en: move HWRM API implementation into separate file")
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During ifdown, we call bnxt_inv_fw_health_reg() which will clear
both the status_reliable and resets_reliable flags if these
registers are mapped. This is correct because a FW reset during
ifdown will clear these register mappings. If we detect that FW
has gone through reset during the next ifup, we will remap these
registers.
But during normal ifup with no FW reset, we need to restore the
resets_reliable flag otherwise we will not show the reset counter
during devlink diagnose.
Fixes: 8cc95ceb70 ("bnxt_en: improve fw diagnose devlink health messages")
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should setup multicast only when net_device flags explicitly
has IFF_MULTICAST set. Otherwise we will incorrectly turn it on
even when not asked. Fix it by only passing the multicast table
to the firmware if IFF_MULTICAST is set.
Fixes: 7d2837dd7a ("bnxt_en: Setup multicast properly after resetting device.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code, we setup the port to PHY or MAC loopback mode
and then transmit a test broadcast packet for the loopback test. This
scheme fails sometime if the port is shared with management firmware
that can also send packets. The driver may receive the management
firmware's packet and the test will fail when the contents don't
match the test packet.
Change the test packet to use it's own MAC address as the destination
and setup the port to only receive it's own MAC address. This should
filter out other packets sent by management firmware.
Fixes: 91725d89b9 ("bnxt_en: Add PHY loopback to ethtool self-test.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For offline (destructive) self tests, we need to stop the RDMA driver
first. Otherwise, the RDMA driver will run into unrecoverable errors
when destructive firmware tests are being performed.
The irq_re_init parameter used in the half close and half open
sequence when preparing the NIC for offline tests should be set to
true because the RDMA driver will free all IRQs before the offline
tests begin.
Fixes: 55fd0cf320 ("bnxt_en: Add external loopback test to ethtool selftest.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Ben Li <ben.li@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool --show-fec <interface> does not show anything when the Active
FEC setting in the chip is set to None. Fix it to properly return
ETHTOOL_FEC_OFF in that case.
Fixes: 8b2775890a ("bnxt_en: Report FEC settings to ethtool.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b3612ccdf2 ("net: dsa: microchip: implement multi-bridge support")
plugged a packet leak between ports that were members of different bridges.
Unfortunately, this broke another use case, namely that of more than two
ports that are members of the same bridge.
After that commit, when a port is added to a bridge, hardware bridging
between other member ports of that bridge will be cleared, preventing
packet exchange between them.
Fix by ensuring that the Port VLAN Membership bitmap includes any existing
ports in the bridge, not just the port being added.
Fixes: b3612ccdf2 ("net: dsa: microchip: implement multi-bridge support")
Signed-off-by: Svenning Sørensen <sss@secomea.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-02-18
This series contains updates to ice driver only.
Wojciech fixes protocol matching for slow-path switchdev so that all
packets are correctly redirected.
Michal removes accidental unconditional setting of l4 port filtering
flag.
Jake adds locking to protect VF reset and removal to fix various issues
that can be encountered when they race with each other.
Tom Rix propagates an error and initializes a struct to resolve reported
Clang issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ida_simple_get() returns an id between min (0) and max (NFP_MAX_MAC_INDEX)
inclusive.
So NFP_MAX_MAC_INDEX (0xff) is a valid id.
In order for the error handling path to work correctly, the 'invalid'
value for 'ida_idx' should not be in the 0..NFP_MAX_MAC_INDEX range,
inclusive.
So set it to -1.
Fixes: 20cce88650 ("nfp: flower: enable MAC address sharing for offloadable devs")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220218131535.100258-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clang static analysis reports this issues
ice_common.c:5008:21: warning: The left expression of the compound
assignment is an uninitialized value. The computed value will
also be garbage
ldo->phy_type_low |= ((u64)buf << (i * 16));
~~~~~~~~~~~~~~~~~ ^
When called from ice_cfg_phy_fec() ldo is the uninitialized local
variable tlv. So initialize.
Fixes: ea78ce4dab ("ice: add link lenient and default override support")
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Clang static analysis reports this issue
time64.h:69:50: warning: The left operand of '+'
is a garbage value
set_normalized_timespec64(&ts_delta, lhs.tv_sec + rhs.tv_sec,
~~~~~~~~~~ ^
In ice_ptp_adjtime_nonatomic(), the timespec64 variable 'now'
is set by ice_ptp_gettimex64(). This function can fail
with -EBUSY, so 'now' can have a gargbage value.
So check the return.
Fixes: 06c16d89d2 ("ice: register 1588 PTP clock device object for E810 devices")
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit c503e63200 ("ice: Stop processing VF messages during teardown")
introduced a driver state flag, ICE_VF_DEINIT_IN_PROGRESS, which is
intended to prevent some issues with concurrently handling messages from
VFs while tearing down the VFs.
This change was motivated by crashes caused while tearing down and
bringing up VFs in rapid succession.
It turns out that the fix actually introduces issues with the VF driver
caused because the PF no longer responds to any messages sent by the VF
during its .remove routine. This results in the VF potentially removing
its DMA memory before the PF has shut down the device queues.
Additionally, the fix doesn't actually resolve concurrency issues within
the ice driver. It is possible for a VF to initiate a reset just prior
to the ice driver removing VFs. This can result in the remove task
concurrently operating while the VF is being reset. This results in
similar memory corruption and panics purportedly fixed by that commit.
Fix this concurrency at its root by protecting both the reset and
removal flows using the existing VF cfg_lock. This ensures that we
cannot remove the VF while any outstanding critical tasks such as a
virtchnl message or a reset are occurring.
This locking change also fixes the root cause originally fixed by commit
c503e63200 ("ice: Stop processing VF messages during teardown"), so we
can simply revert it.
Note that I kept these two changes together because simply reverting the
original commit alone would leave the driver vulnerable to worse race
conditions.
Fixes: c503e63200 ("ice: Stop processing VF messages during teardown")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Accidentally filter flag for none encapsulated l4 port field is always
set. Even if user wants to add encapsulated l4 port field.
Remove this unnecessary flag setting.
Fixes: 9e300987d4 ("ice: VXLAN and Geneve TC support")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In switchdev mode, slow-path rules need to match all protocols, in order
to correctly redirect unfiltered or missed packets to the uplink. To set
this up for the virtual function to uplink flow, the rule that redirects
packets to the control VSI must have the tunnel type set to
ICE_SW_TUN_AND_NON_TUN. As a result of that new tunnel type being set,
ice_get_compat_fv_bitmap will select ICE_PROF_ALL. At that point all
profiles would be selected for this rule, resulting in the desired
behavior. Without this change slow-path would not work with
tunnel protocols.
Fixes: 8b032a55c1 ("ice: low level support for tunnels")
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
devm_kmalloc() returns a pointer to allocated memory on success, NULL
on failure. While lp->indirect_lock is allocated by devm_kmalloc()
without proper check. It is better to check the value of it to
prevent potential wrong memory access.
Fixes: f14f5c11f0 ("net: ll_temac: Support indirect_mutex share within TEMAC IP")
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A malicious device can leak heap data to user space
providing bogus frame lengths. Introduce a sanity check.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a 6pack device is detaching, the sixpack_close() will act to cleanup
necessary resources. Although del_timer_sync() in sixpack_close()
won't return if there is an active timer, one could use mod_timer() in
sp_xmit_on_air() to wake up timer again by calling userspace syscall such
as ax25_sendmsg(), ax25_connect() and ax25_ioctl().
This unexpected waked handler, sp_xmit_on_air(), realizes nothing about
the undergoing cleanup and may still call pty_write() to use driver layer
resources that have already been released.
One of the possible race conditions is shown below:
(USE) | (FREE)
ax25_sendmsg() |
ax25_queue_xmit() |
... |
sp_xmit() |
sp_encaps() | sixpack_close()
sp_xmit_on_air() | del_timer_sync(&sp->tx_t)
mod_timer(&sp->tx_t,...) | ...
| unregister_netdev()
| ...
(wait a while) | tty_release()
| tty_release_struct()
| release_tty()
sp_xmit_on_air() | tty_kref_put(tty_struct) //FREE
pty_write(tty_struct) //USE | ...
The corresponding fail log is shown below:
===============================================================
BUG: KASAN: use-after-free in __run_timers.part.0+0x170/0x470
Write of size 8 at addr ffff88800a652ab8 by task swapper/2/0
...
Call Trace:
...
queue_work_on+0x3f/0x50
pty_write+0xcd/0xe0pty_write+0xcd/0xe0
sp_xmit_on_air+0xb2/0x1f0
call_timer_fn+0x28/0x150
__run_timers.part.0+0x3c2/0x470
run_timer_softirq+0x3b/0x80
__do_softirq+0xf1/0x380
...
This patch reorders the del_timer_sync() after the unregister_netdev()
to avoid UAF bugs. Because the unregister_netdev() is well synchronized,
it flushs out any pending queues, waits the refcount of net_device
decreases to zero and removes net_device from kernel. There is not any
running routines after executing unregister_netdev(). Therefore, we could
not arouse timer from userspace again.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter.
Current release - regressions:
- dsa: lantiq_gswip: fix use after free in gswip_remove()
- smc: avoid overwriting the copies of clcsock callback functions
Current release - new code bugs:
- iwlwifi:
- fix use-after-free when no FW is present
- mei: fix the pskb_may_pull check in ipv4
- mei: retry mapping the shared area
- mvm: don't feed the hardware RFKILL into iwlmei
Previous releases - regressions:
- ipv6: mcast: use rcu-safe version of ipv6_get_lladdr()
- tipc: fix wrong publisher node address in link publications
- iwlwifi: mvm: don't send SAR GEO command for 3160 devices,
avoid FW assertion
- bgmac: make idm and nicpm resource optional again
- atl1c: fix tx timeout after link flap
Previous releases - always broken:
- vsock: remove vsock from connected table when connect is
interrupted by a signal
- ping: change destination interface checks to match raw sockets
- crypto: af_alg - get rid of alg_memory_allocated to avoid confusing
semantics (and null-deref) after SO_RESERVE_MEM was added
- ipv6: make exclusive flowlabel checks per-netns
- bonding: force carrier update when releasing slave
- sched: limit TC_ACT_REPEAT loops
- bridge: multicast: notify switchdev driver whenever MC processing
gets disabled because of max entries reached
- wifi: brcmfmac: fix crash in brcm_alt_fw_path when WLAN not found
- iwlwifi: fix locking when "HW not ready"
- phy: mediatek: remove PHY mode check on MT7531
- dsa: mv88e6xxx: flush switchdev FDB workqueue before removing VLAN
- dsa: lan9303:
- fix polarity of reset during probe
- fix accelerated VLAN handling
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Nrzq
-----END PGP SIGNATURE-----
Merge tag 'net-5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless and netfilter.
Current release - regressions:
- dsa: lantiq_gswip: fix use after free in gswip_remove()
- smc: avoid overwriting the copies of clcsock callback functions
Current release - new code bugs:
- iwlwifi:
- fix use-after-free when no FW is present
- mei: fix the pskb_may_pull check in ipv4
- mei: retry mapping the shared area
- mvm: don't feed the hardware RFKILL into iwlmei
Previous releases - regressions:
- ipv6: mcast: use rcu-safe version of ipv6_get_lladdr()
- tipc: fix wrong publisher node address in link publications
- iwlwifi: mvm: don't send SAR GEO command for 3160 devices, avoid FW
assertion
- bgmac: make idm and nicpm resource optional again
- atl1c: fix tx timeout after link flap
Previous releases - always broken:
- vsock: remove vsock from connected table when connect is
interrupted by a signal
- ping: change destination interface checks to match raw sockets
- crypto: af_alg - get rid of alg_memory_allocated to avoid confusing
semantics (and null-deref) after SO_RESERVE_MEM was added
- ipv6: make exclusive flowlabel checks per-netns
- bonding: force carrier update when releasing slave
- sched: limit TC_ACT_REPEAT loops
- bridge: multicast: notify switchdev driver whenever MC processing
gets disabled because of max entries reached
- wifi: brcmfmac: fix crash in brcm_alt_fw_path when WLAN not found
- iwlwifi: fix locking when "HW not ready"
- phy: mediatek: remove PHY mode check on MT7531
- dsa: mv88e6xxx: flush switchdev FDB workqueue before removing VLAN
- dsa: lan9303:
- fix polarity of reset during probe
- fix accelerated VLAN handling"
* tag 'net-5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
bonding: force carrier update when releasing slave
nfp: flower: netdev offload check for ip6gretap
ipv6: fix data-race in fib6_info_hw_flags_set / fib6_purge_rt
ipv4: fix data races in fib_alias_hw_flags_set
net: dsa: lan9303: add VLAN IDs to master device
net: dsa: lan9303: handle hwaccel VLAN tags
vsock: remove vsock from connected table when connect is interrupted by a signal
Revert "net: ethernet: bgmac: Use devm_platform_ioremap_resource_byname"
ping: fix the dif and sdif check in ping_lookup
net: usb: cdc_mbim: avoid altsetting toggling for Telit FN990
net: sched: limit TC_ACT_REPEAT loops
tipc: fix wrong notification node addresses
net: dsa: lantiq_gswip: fix use after free in gswip_remove()
ipv6: per-netns exclusive flowlabel checks
net: bridge: multicast: notify switchdev driver whenever MC processing gets disabled
CDC-NCM: avoid overflow in sanity checking
mctp: fix use after free
net: mscc: ocelot: fix use-after-free in ocelot_vlan_del()
bonding: fix data-races around agg_select_timer
dpaa2-eth: Initialize mutex used in one step timestamping path
...
In __bond_release_one(), bond_set_carrier() is only called when bond
device has no slave. Therefore, if we remove the up slave from a master
with two slaves and keep the down slave, the master will remain up.
Fix this by moving bond_set_carrier() out of if (!bond_has_slaves(bond))
statement.
Reproducer:
$ insmod bonding.ko mode=0 miimon=100 max_bonds=2
$ ifconfig bond0 up
$ ifenslave bond0 eth0 eth1
$ ifconfig eth0 down
$ ifenslave -d bond0 eth1
$ cat /proc/net/bonding/bond0
Fixes: ff59c4563a ("[PATCH] bonding: support carrier state for master")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/1645021088-38370-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPv6 GRE tunnels are not being offloaded, this is caused by a missing
netdev offload check. The functionality of IPv6 GRE tunnel offloading
was previously added but this check was not included. Adding the
ip6gretap check allows IPv6 GRE tunnels to be offloaded correctly.
Fixes: f7536ffb09 ("nfp: flower: Allow ipv6gretap interface for offloading")
Signed-off-by: Danie du Toit <danie.dutoit@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220217124820.40436-1-louis.peens@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the master device does VLAN filtering, the IDs used by the switch
must be added for any frames to be received. Do this in the
port_enable() function, and remove them in port_disable().
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220216204818.28746-1-mans@mansr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 3710e80952.
Since idm_base and nicpm_base are still optional resources not present
on all platforms, this breaks the driver for everything except Northstar
2 (which has both).
The same change was already reverted once with 755f5738ff ("net:
broadcom: fix a mistake about ioremap resource").
So let's do it again.
Fixes: 3710e80952 ("net: ethernet: bgmac: Use devm_platform_ioremap_resource_byname")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
[florian: Added comments to explain the resources are optional]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220216184634.2032460-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit FN990
0x1071 composition in order to avoid bind error.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put(priv->ds->slave_mii_bus->dev.of_node) should be
done before mdiobus_free(priv->ds->slave_mii_bus).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 0d120dfb5d ("net: dsa: lantiq_gswip: don't use devres for mdiobus")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1644921768-26477-1-git-send-email-khoroshilov@ispras.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A broken device may give an extreme offset like 0xFFF0
and a reasonable length for a fragment. In the sanity
check as formulated now, this will create an integer
overflow, defeating the sanity check. Both offset
and offset + len need to be checked in such a manner
that no overflow can occur.
And those quantities should be unsigned.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ocelot_vlan_member_del() will free the struct ocelot_bridge_vlan, so if
this is the same as the port's pvid_vlan which we access afterwards,
what we're accessing is freed memory.
Fix the bug by determining whether to clear ocelot_port->pvid_vlan prior
to calling ocelot_vlan_member_del().
Fixes: d4004422f6 ("net: mscc: ocelot: track the port pvid using a pointer")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1588 Single Step Timestamping code path uses a mutex to
enforce atomicity for two events:
- update of ptp single step register
- transmit ptp event packet
Before this patch the mutex was not initialized. This
caused unexpected crashes in the Tx function.
Fixes: c55211892f ("dpaa2-eth: support PTP Sync packet one-step timestamping")
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang static analysis reports this representative problem
dpaa2-switch-flower.c:616:24: warning: The right operand of '=='
is a garbage value
tmp->cfg.vlan_id == vlan) {
^ ~~~~
vlan is set in dpaa2_switch_flower_parse_mirror_key(). However
this function can return success without setting vlan. So
change the default return to -EOPNOTSUPP.
Fixes: 0f3faece58 ("dpaa2-switch: add VLAN based mirroring")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Schmidt says:
====================
Only a single fix this time.
Miquel Raynal fixed the lifs/sifs periods in the ca82010 to take the actual
symbol duration time into account.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mt7531_phy_mode_supported in the DSA driver set supported
mode to PHY_INTERFACE_MODE_GMII instead of PHY_INTERFACE_MODE_INTERNAL
for the internal PHY, so this check breaks the PHY initialization:
mt7530 mdio-bus:00 wan (uninitialized): failed to connect to PHY: -EINVAL
Remove the check to make it work again.
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes: e40d2cca01 ("net: phy: add MediaTek Gigabit Ethernet PHY driver")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This SL-6000 says Direct Line, not Ethernet
v2: added Reporter and Link
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: Ross Maynard <bids.7405@bigpond.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215361
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx is special among DSA drivers in that it requires the VTU to
contain the VID of the FDB entry it modifies in
mv88e6xxx_port_db_load_purge(), otherwise it will return -EOPNOTSUPP.
Sometimes due to races this is not always satisfied even if external
code does everything right (first deletes the FDB entries, then the
VLAN), because DSA commits to hardware FDB entries asynchronously since
commit c9eb3e0f87 ("net: dsa: Add support for learning FDB through
notification").
Therefore, the mv88e6xxx driver must close this race condition by
itself, by asking DSA to flush the switchdev workqueue of any FDB
deletions in progress, prior to exiting a VLAN.
Fixes: c9eb3e0f87 ("net: dsa: Add support for learning FDB through notification")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The COMMS package can enable the hardware parser to recognize IPSEC
frames with ESP header and SPI identifier. If this package is available
and configured for loading in /lib/firmware, then the driver will
succeed in enabling this protocol type for RSS.
This in turn allows the hardware to hash over the SPI and use it to pick
a consistent receive queue for the same secure flow. Without this all
traffic is steered to the same queue for multiple traffic threads from
the same IP address. For that reason this is marked as a fix, as the
driver supports the model, but it wasn't enabled.
If the package is not available, adding this type will fail, but the
failure is ignored on purpose as it has no negative affect.
Fixes: c90ed40cef ("ice: Enable writing hardware filtering tables")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some small USB driver fixes for 5.17-rc4 that resolve some
reported issues and add new device ids:
- usb-serial new device ids
- ulpi cleanup fixes
- f_fs use-after-free fix
- dwc3 driver fixes
- ax88179_178a usb network driver fix
- usb gadget fixes
There is a revert at the end of this series to resolve a build problem
that 0-day found yesterday. Most of these have been in linux-next,
except for the last few, and all have now passed 0-day tests.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYgeLiw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylpQACaAnwfFoAxK5yr2IEu5WmxPmY0pSkAnROqF4JO
CQhohQ61DjpdK0ikJWsZ
=n8Yn
-----END PGP SIGNATURE-----
Merge tag 'usb-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB driver fixes for 5.17-rc4 that resolve some
reported issues and add new device ids:
- usb-serial new device ids
- ulpi cleanup fixes
- f_fs use-after-free fix
- dwc3 driver fixes
- ax88179_178a usb network driver fix
- usb gadget fixes
There is a revert at the end of this series to resolve a build problem
that 0-day found yesterday. Most of these have been in linux-next,
except for the last few, and all have now passed 0-day tests"
* tag 'usb-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "usb: dwc2: drd: fix soft connect when gadget is unconfigured"
usb: dwc2: drd: fix soft connect when gadget is unconfigured
usb: gadget: rndis: check size of RNDIS_MSG_SET command
USB: gadget: validate interface OS descriptor requests
usb: core: Unregister device on component_add() failure
net: usb: ax88179_178a: Fix out-of-bounds accesses in RX fixup
usb: dwc3: gadget: Prevent core from processing stale TRBs
USB: serial: cp210x: add CPI Bulk Coin Recycler id
USB: serial: cp210x: add NCR Retail IO box id
USB: serial: ftdi_sio: add support for Brainboxes US-159/235/320
usb: gadget: f_uac2: Define specific wTerminalType
usb: gadget: udc: renesas_usb3: Fix host to USB_ROLE_NONE transition
usb: raw-gadget: fix handling of dual-direction-capable endpoints
usb: usb251xb: add boost-up property support
usb: ulpi: Call of_node_put correctly
usb: ulpi: Move of_node_put to ulpi_dev_release
USB: serial: option: add ZTE MF286D modem
USB: serial: ch341: add support for GW Instek USB2.0-Serial devices
usb: f_fs: Fix use-after-free for epfile
usb: dwc3: xilinx: fix uninitialized return value
If NIC had packets in tx queue at the moment link down event
happened, it could result in tx timeout when link got back up.
Since device has more than one tx queue we need to reset them
accordingly.
Fixes: 057f4af2b1 ("atl1c: add 4 RX/TX queue support for Mikrotik 10/25G NIC")
Signed-off-by: Gatis Peisenieks <gatis@mikrotik.com>
Link: https://lore.kernel.org/r/20220211065123.4187615-1-gatis@mikrotik.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We cannot do the cancel_work_sync from after the unregister_netdev, as
the dev pointer is no longer valid, causing a uaf on ldisc unregister
(or device close).
Instead, do the cancel_work_sync from the ndo_uninit op, where the dev
still exists, but the queue has stopped.
Fixes: 7bd9890f3d ("mctp: serial: cancel tx work on ldisc close")
Reported-by: Luo Likang <luolikang@nsfocus.com>
Tested-by: Luo Likang <luolikang@nsfocus.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20220211011552.1861886-1-jk@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The reset input to the LAN9303 chip is active low, and devicetree
gpio handles reflect this. Therefore, the gpio should be requested
with an initial state of high in order for the reset signal to be
asserted. Other uses of the gpio already use the correct polarity.
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fianelil <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220209145454.19749-1-mans@mansr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Second set of fixes for v5.17. This is the first pull request with
both driver and stack patches.
Most important here are a regression fix for brcmfmac USB devices and
an iwlwifi fix for use after free when the firmware was missing. We
have new maintainers for ath9k and wcn36xx as well as ath6kl is now
orphaned. Also smaller fixes to iwlwifi and stack.
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmIGLQoRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZvMSwf/QSGm9vlSC1rfiG/+cy65pg1bY4m7DM1g
fiZJP3X690jBzi45B6ld3sI47DdycJH5jhyj7A9DIp2sPNGuULaGNjUrV2eQpjjk
BU2tBOBLy/P9aoyMuRTeF4H2QXMgRXGTVhVF4oydmzOigKyJx1GxOt4tfkqPATYb
3SEKp2wbwUjGA0K4xCD0LFnJHFcp3XSHFRNLN6QpZz/Ku+BcLq+cUWfHUKqDZFl4
rNa4BH5xyydFNNURM6K20iKacq/8s5JOxdGAS+OmBGXKyZT/kbxvZDNz3rUsXuhd
C7MYkQPGeXayfTrJbHwV2CBpaN+hy3KkU0ecOG6FACu9H4hfoJfynA==
=ioe+
-----END PGP SIGNATURE-----
Merge tag 'wireless-2022-02-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
wireless fixes for v5.17
Second set of fixes for v5.17. This is the first pull request with
both driver and stack patches.
Most important here are a regression fix for brcmfmac USB devices and
an iwlwifi fix for use after free when the firmware was missing. We
have new maintainers for ath9k and wcn36xx as well as ath6kl is now
orphaned. Also smaller fixes to iwlwifi and stack.
ax88179_rx_fixup() contains several out-of-bounds accesses that can be
triggered by a malicious (or defective) USB device, in particular:
- The metadata array (hdr_off..hdr_off+2*pkt_cnt) can be out of bounds,
causing OOB reads and (on big-endian systems) OOB endianness flips.
- A packet can overlap the metadata array, causing a later OOB
endianness flip to corrupt data used by a cloned SKB that has already
been handed off into the network stack.
- A packet SKB can be constructed whose tail is far beyond its end,
causing out-of-bounds heap data to be considered part of the SKB's
data.
I have tested that this can be used by a malicious USB device to send a
bogus ICMPv6 Echo Request and receive an ICMPv6 Echo Reply in response
that contains random kernel heap data.
It's probably also possible to get OOB writes from this on a
little-endian system somehow - maybe by triggering skb_cow() via IP
options processing -, but I haven't tested that.
Fixes: e2ca90c276 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Cc: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since struct mv88e6xxx_mdio_bus *mdio_bus is the bus->priv of something
allocated with mdiobus_alloc_size(), this means that mdiobus_free(bus)
will free the memory backing the mdio_bus as well. Therefore, the
mdio_bus->list element is freed memory, but we continue to iterate
through the list of MDIO buses using that list element.
To fix this, use the proper list iterator that handles element deletion
by keeping a copy of the list element next pointer.
Fixes: f53a2ce893 ("net: dsa: mv88e6xxx: don't use devres for mdiobus")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220210174017.3271099-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-02-10
Dan Carpenter propagates an error in FEC configuration.
Jesse fixes TSO offloads of IPIP and SIT frames.
Dave adds a dedicated LAG unregister function to resolve a KASAN error
and moves auxiliary device re-creation after LAG removal to the service
task to avoid issues with RTNL lock.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Avoid RTNL lock when re-creating auxiliary device
ice: Fix KASAN error in LAG NETDEV_UNREGISTER handler
ice: fix IPIP and SIT TSO offload
ice: fix an error code in ice_cfg_phy_fec()
====================
Link: https://lore.kernel.org/r/20220210170515.2609656-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
An ongoing workqueue populates the stats buffer. At the same time, a user
might query the statistics. While writing to the buffer is mutex-locked,
reading from the buffer wasn't. This could lead to buggy reads by ethtool.
This patch fixes the former blamed commit, but the bug was introduced in
the latter.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Fixes: 1e1caa9735 ("ocelot: Clean up stats update deferred work")
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Reported-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/all/20220210150451.416845-2-colin.foster@in-advantage.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a call to re-create the auxiliary device happens in a context that has
already taken the RTNL lock, then the call flow that recreates auxiliary
device can hang if there is another attempt to claim the RTNL lock by the
auxiliary driver.
To avoid this, any call to re-create auxiliary devices that comes from
an source that is holding the RTNL lock (e.g. netdev notifier when
interface exits a bond) should execute in a separate thread. To
accomplish this, add a flag to the PF that will be evaluated in the
service task and dealt with there.
Fixes: f9f5301e7e ("ice: Register auxiliary device to provide RDMA")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, the same handler is called for both a NETDEV_BONDING_INFO
LAG unlink notification as for a NETDEV_UNREGISTER call. This is
causing a problem though, since the netdev_notifier_info passed has
a different structure depending on which event is passed. The problem
manifests as a call trace from a BUG: KASAN stack-out-of-bounds error.
Fix this by creating a handler specific to NETDEV_UNREGISTER that only
is passed valid elements in the netdev_notifier_info struct for the
NETDEV_UNREGISTER event.
Also included is the removal of an unbalanced dev_put on the peer_netdev
and related braces.
Fixes: 6a8b357278 ("ice: Respond to a NETDEV_UNREGISTER event for LAG")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver was avoiding offload for IPIP (at least) frames due to
parsing the inner header offsets incorrectly when trying to check
lengths.
This length check works for VXLAN frames but fails on IPIP frames
because skb_transport_offset points to the inner header in IPIP
frames, which meant the subtraction of transport_header from
inner_network_header returns a negative value (-20).
With the code before this patch, everything continued to work, but GSO
was being used to segment, causing throughputs of 1.5Gb/s per thread.
After this patch, throughput is more like 10Gb/s per thread for IPIP
traffic.
Fixes: e94d447866 ("ice: Implement filter sync, NDO operations and bump version")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Propagate the error code from ice_get_link_default_override() instead
of returning success.
Fixes: ea78ce4dab ("ice: add link lenient and default override support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>