mlx5_cmd_exec() might fail - need to check return value.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This readds the config option CONFIG_OPENVSWITCH_VXLAN to avoid a
hard dependency of OVS on VXLAN. It moves the VXLAN config compat
code to vport-vxlan.c and allows compliation as a module.
Fixes: 614732eaa1 ("openvswitch: Use regular VXLAN net_device device")
Fixes: 2661371ace ("openvswitch: fix compilation when vxlan is a module")
Cc: Pravin B Shelar <pshelar@nicira.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the IPv6 equivalent of commit
6c8b4e3ff8 ("arp: flush arp cache on IFF_NOARP change")
Without it, we keep buggy neighbours in the cache, with destination
MAC address equal to our own MAC address.
Tested:
tcpdump -i eth0 -s 0 ip6 -n -e &
ip link set dev eth0 arp off
ping6 remote // sends buggy frames
ip link set dev eth0 arp on
ping6 remote // should work once kernel is patched
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Mario Fanelli <mariofanelli@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Field pktgen_dev.allocated_skbs had been written to, but never read
from. The number of allocated skbs can be deduced anyway, from the total
number of sent packets and the 'clone_skb' param.
Signed-off-by: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate enough space so as not to force the outgoing net device to do
skb_realloc_headroom().
Signed-off-by: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any external user should use the registration API instead of
accessing this directly.
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of defconfig consolidation using fragments, we'd like to be
able to have the same drivers enabled on 32-bit and 64-bit. Gianfar
happens to only exist on 32-bit systems, and when building the
resulting 64-bit kernel warnings were produced.
A couple of the warnings are trivial, but the rfbptr code has deeper
issues. It uses the virtual address as the DMA address, which again,
happens to work in the environments where this driver is currently
used, but is not the right thing to do.
Fixes: 45b679c9a3 ("gianfar: Implement PAUSE frame generation
support")
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert says:
====================
net: Initialize sk_hash to random value and reset for failing cnxs
This patch set implements a common function to simply set sk_txhash to
a random number instead of going through the trouble to call flow
dissector. From dst_negative_advice we now reset the sk_txhash in hopes
of finding a better ECMP path through the network. Changing sk_txhash
affects:
- IPv6 flow label and UDP source port which affect ECMP in the network
- Local ECMP route selection (pending changes to use sk_txhash)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a connection is failing a transport protocol calls
dst_negative_advice to try to get a better route. This patch includes
changing the sk_txhash in that function. This provides a rudimentary
method to try to find a different path in the network since sk_txhash
affects ECMP on the local host and through the network (via flow labels
or UDP source port in encapsulation).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates sk_set_txhash and eliminates protocol specific
inet_set_txhash and ip6_set_txhash. sk_set_txhash simply sets a
random number instead of performing flow dissection. sk_set_txash
is also allowed to be called multiple times for the same socket,
we'll need this when redoing the hash for negative routing advice.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wire up the syscall number and regs so the tests work on powerpc.
With the powerpc kernel support just merged, all tests pass on ppc64,
ppc64 (compat), ppc64le, ppc, ppc64e and ppc64e (compat).
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The seccomp_bpf test uses BPF_LD|BPF_W|BPF_ABS to load 32-bit values
from seccomp_data->args. On big endian machines this will load the high
word of the argument, which is not what the test wants.
Borrow a hack from samples/seccomp/bpf-helper.h which changes the offset
on big endian to account for this.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Kees Cook <keescook@chromium.org>
This commit enables seccomp filter on powerpc, now that we have all the
necessary pieces in place.
To support seccomp's desire to modify the syscall return value under
some circumstances, we use a different ABI to the ptrace ABI. That is we
use r3 as the syscall return value, and orig_gpr3 is the first syscall
parameter.
This means the seccomp code, or a ptracer via SECCOMP_RET_TRACE, will
see -ENOSYS preloaded in r3. This is identical to the behaviour on x86,
and allows seccomp or the ptracer to either leave the -ENOSYS or change
it to something else, as well as rejecting or not the syscall by
modifying r0.
If seccomp does not reject the syscall, we restore the register state to
match what ptrace and audit expect, ie. r3 is the first syscall
parameter again. We do this restore using orig_gpr3, which may have been
modified by seccomp, which allows seccomp to modify the first syscall
paramater and allow the syscall to proceed.
We need to #ifdef the the additional handling of r3 for seccomp, so move
it all out of line.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Writing a large value into a voltage limit attribute can result
in an overflow due to an auto-conversion from unsigned long to
unsigned int.
Cc: Constantine Shulyupin <const@MakeLinux.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pwm attributes have well defined names, which should be used.
Cc: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
Cc: stable@vger.kernel.org #v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
More drm-misc, mostly fine-tuning of atomic helpers. They're mostly
driver-wide interface changes of the helpers and I need them for i915
work, so I plan to pull this tag into drm-intel-next too.
* tag 'topic/drm-misc-2015-07-28' of git://anongit.freedesktop.org/drm-intel:
drm/atomic: Update legacy DPMS state during modesets, v3.
drm: Make the connector dpms callback return a value, v2.
drm/atomic: pass old crtc state to atomic_begin/flush.
drm/atomic: add connectors_changed to separate it from mode_changed, v2
drm: Fix DP_TEST_COUNT_MASK
Fix for nasty crash on mdp4 in disable path, fix for dma-buf export,
smb leak on mdp5 which could result in intermittent modeset fails, and
don't let interrupted system call disturb atomic commit once we are
past the point of no return.
* 'msm-fixes-4.2' of git://people.freedesktop.org/~robclark/linux:
drm/msm/mdp5: release SMB (shared memory blocks) in various cases
drm/msm: change to uninterruptible wait in atomic commit
drm/msm: mdp4: Fix drm_framebuffer dereference crash
drm/msm: fix msm_gem_prime_get_sg_table()
Radeon and amdgpu fixes for 4.2. The audio fix ended up being more
invasive than I would have liked, but this should finally fix up the
last of the regressions since DP audio support was added.
* 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: add new parameter to seperate map and unmap
drm/amdgpu: hdp_flush is not needed for inside IB
drm/amdgpu: different emit_ib for gfx and compute
drm/amdgpu: information leak in amdgpu_info_ioctl()
drm/amdgpu: clean up init sequence for failures
drm/radeon/combios: add some validation of lvds values
drm/radeon: rework audio modeset to handle non-audio hdmi features
drm/radeon: rework audio detect (v4)
drm/amdgpu: Drop drm/ prefix for including drm.h in amdgpu_drm.h
drm/radeon: Drop drm/ prefix for including drm.h in radeon_drm.h
Murali Karicheri says:
====================
net: netcp: bug fixes for dynamic module support
This series fixes few bugs to allow keystone netcp modules to be
dynamically loaded and removed. Currently it allows following
sequence multiple times
insmod cpsw_ale.ko
insmod davinci_mdio.ko
insmod keystone_netcp.ko
insmod keystone_netcp_ethss.ko
ifup eth0
ifup eth1
ping <hosts on eth0>
ping <hosts on eth1>
ifdown eth1
ifdown eth0
rmmod keystone_netcp_ethss.ko
rmmod keystone_netcp.ko
rmmod davinci_mdio.ko
rmmod cpsw_ale.ko
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch clean up error handle code to use goto label properly. In some
cases, the code unnecessarily use goto instead of just returning the error
code. Code also make explicit calls to devm_* APIs on error which is
not necessary. In the gbe_remove() also it makes similar calls which is
also unnecessary.
Also fix few checkpatch warnings
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code seems to assume a null is returned when the list is empty
from first_sec_slave() to break the loop which is incorrect. Fix the
code by using list_empty().
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if user do rmmod keystone_netcp.ko following warning is
seen :-
[ 59.035891] ------------[ cut here ]------------
[ 59.040535] WARNING: CPU: 2 PID: 1619 at drivers/net/ethernet/ti/
netcp_core.c:2127 netcp_remove)
This is because the interface list is not cleaned up in netcp_remove.
This patch fixes this. Also fix some checkpatch related warnings.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix a recently introduced issue in the cpufreq core causing
it to attempt to create duplicate symbolic links to the policy
directory in sysfs for CPUs that are offline when the cpufreq
driver is being registered (Rafael J Wysocki).
- Fix a recently introduced problem in the ACPI device power
management core code causing it to store an incorrect value
in the device object's power.state field in some cases which
in turn leads to attempts to turn power resources off while
they should still be on going forward (Mika Westerberg).
- Fix an intel_pstate driver issue introduced during the 4.1 cycle
which leads to kernel panics on boot on Knights Landing chips due
to incomplete support for them in that driver (Lukasz Anaczkowski).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=tXB4
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix three regressions, two recent ones (cpufreq core and ACPI
device power management) and one introduced during the 4.1 cycle
(intel_pstate).
Specifics:
- Fix a recently introduced issue in the cpufreq core causing it to
attempt to create duplicate symbolic links to the policy directory
in sysfs for CPUs that are offline when the cpufreq driver is being
registered (Rafael J Wysocki)
- Fix a recently introduced problem in the ACPI device power
management core code causing it to store an incorrect value in the
device object's power.state field in some cases which in turn leads
to attempts to turn power resources off while they should still be
on going forward (Mika Westerberg)
- Fix an intel_pstate driver issue introduced during the 4.1 cycle
which leads to kernel panics on boot on Knights Landing chips due
to incomplete support for them in that driver (Lukasz Anaczkowski)"
* tag 'pm+acpi-4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Avoid attempts to create duplicate symbolic links
ACPI / PM: Use target_state to set the device power state
intel_pstate: Add get_scaling cpu_defaults param to Knights Landing
- Fix a logic bug in the DM cache smq policy's creation error path
- Revert a DM cache 4.2-rc3 change that reduced writeback efficiency
- Fix a hang on DM cache device destruction due to improper
prealloc_used accounting introduced in 4.2-rc3
- Update URL for dm-crypt wiki page
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVuWg1AAoJEMUj8QotnQNaTyUH/2csU3My+lgTW85BlEnm3LOa
zeuI+aeTSJ7hTO5x4GYZwK6UTXRts8iR2Np3yZozXv94EioAWwhl6yrJU+hOfwOC
Kse1/xR6wTE2BPMD0rRfscGnXvydilYpcOZCyKQ7OR28Afr6O1HCbDa/Qqnuqmox
yb8vzJp0pYrLC6CjuTep/ofuMkIehCib5XEzwoM/7GsgiLZQgikSEuKmz+Q5hgas
ggsb6weQ5KbHnlBQGQfSkpART9aKbo4BNZJLJ+G3koZFEwo21YuQInIPfAFi7w+d
AUi0UNkVwlqNcXQFSegDCUbw59/JklUdP4hrm6CocWPAnk7XtoNomlJwQNBFUEs=
=YeBR
-----END PGP SIGNATURE-----
Merge tag 'dm-4.2-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- fix DM thinp to consistently return -ENOSPC when out of data space
- fix a logic bug in the DM cache smq policy's creation error path
- revert a DM cache 4.2-rc3 change that reduced writeback efficiency
- fix a hang on DM cache device destruction due to improper
prealloc_used accounting introduced in 4.2-rc3
- update URL for dm-crypt wiki page
* tag 'dm-4.2-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache: fix device destroy hang due to improper prealloc_used accounting
Revert "dm cache: do not wake_worker() in free_migration()"
dm crypt: update wiki page URL
dm cache policy smq: fix alloc_bitset check that always evaluates as false
dm thin: return -ENOSPC when erroring retry list due to out of data space
Radha Mohan Chintakuntla says:
====================
Add MDIO support to ThunderX NIC driver
This patch series adds MDIO support to ThunderX NIC driver by making use
of existing mdio-octeon driver. In the process modified the mdio-octeon
driver to work on both Octeon and ThunderX platforms.
* From v1:
- Removed default selection in Kconfig for MDIO_OCTEON
- Replace uint64 with u64 as suggested by David Daney
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The CONFIG_MDIO_OCTEON is required so that the ThunderX NIC driver can
talk to the PHY drivers.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a possible crash in the octeon_mdiobus_probe function
if the return values are not handled properly.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the mdio-octeon driver to work on both ThunderX and
Octeon SoCs from Cavium Inc.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some of the K2E and K2L platforms, the two DWORDs in
efuse occupied by the pre-programmed mac address for
slave port 1 are swapped. To workaround this issue,
this patch adds a new define NETCP_EFUSE_ADDR_SWAP (2)
which signifies the occurrence of such swapping so that
the driver can take proper action. The flag can be
enabled in the corresponding netcp interface dts binding
as efuse-mac = <2> under the corresponding netcp
interface node.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the SILK board dependent part of the Ether device node.
Enable DHCP and NFS root for the kernel booting.
Based on the original patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A7794 SoC based SILK low cost board.
SCIF2 serial port support is included, so that the serial console can work.
Based on the original patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In commit d999297c3d
("tipc: reduce locking scope during packet reception") we introduced
a new function tipc_build_bcast_sync_msg(), which carries initial
synchronization data between two nodes at first contact and at
re-contact. In this function, we missed to add synchronization data,
with the effect that the broadcast link endpoints will fail to
synchronize correctly at re-contact between a running and a restarted
node. All other cases work as intended.
With this commit, we fix this bug.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These callbacks are called with interrupts disabled from the core
code. Fixup the local caller to disable interrupts.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Migrate apic driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
We weren't doing anything while switching to resume mode and so that
callback isn't implemented.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Bandan Das <bsd@redhat.com>
Link: http://lkml.kernel.org/r/1896ac5989d27f2ac37f4786af9bd537e1921b83.1437042675.git.viresh.kumar@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The only three users of that field are not using the msi_controller
structure anymore, so drop it altogether.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-20-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The X-Gene MSI driver only uses the msi_controller structure as
a way to match the host bridge with its MSI HW, and thus the
msi_domain.
But now that we can directly associate an msi_domain with a device,
there is no use keeping this msi_controller around.
Just remove all traces of msi_controller from the driver.
Tested-by: Duc Dang <dhdang@apm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-19-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In order to support non-PCI MSI with GICv2m, add the minimal
required entry points for the MSI domain, which is actually almost
nothing (we just use the defaults provided by the core code).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-18-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
GICv2m only uses the msi_controller structure as a way to match
the host bridge with its MSI HW, and thus the msi_domain.
But now that we can directly associate an msi_domain with a device,
there is no use keeping this msi_controller around.
Just remove all traces of msi_controller from the driver. Also
tag the inner (non-PCI) domain with DOMAIN_BUS_NEXUS.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-17-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In order to support non-PCI MSI with the GICv3 ITS, add the minimal
required entry points for the MSI domain (an msi_prepare implementation).
The rest is only boilerplate code to find the raw ITS domain.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-16-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We can now lookup the base ITS domain, making it possible to
initialize the PCI/MSI code independently from the main ITS
subsystem.
This allows us to remove all the previously add hooks.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-15-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The GICv3 ITS only uses the msi_controller structure as a way
to match the host bridge with its MSI HW, and thus the msi_domain.
But now that we can directly associate an msi_domain with a device,
there is no use keeping this msi_controller around.
Just remove all traces of msi_controller from the driver.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-14-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now that we can distinguish between multiple domains carrying the
same device_node, tag the raw ITS domain with DOMAIN_BUS_NEXUS.
This will allow MSI providers built on top of the raw ITS domain
to identify it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-13-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It is becoming obvious that having the PCI/MSI code in the same
file as the the core ITS code is giving people implementing non-PCI
MSI support the wrong kind of idea.
In order to make things a bit clearer, let's move the PCI/MSI code
out to its own file. Hopefully it will make it clear that whoever
thinks of hooking into the core ITS better have a very strong point.
We use a temporary entry point that will get removed in a subsequent
patch, once the proper infrastructure is added.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-12-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some IRQ domains are not designed to directly provide interrupts
to devices, but strictly to be used by other domains. An example
of this is the GICv3 ITS, which is completely bus agnostic, and
on which it is possible to implement a PCI/MSI domain.
Just introduce the irq_domain_bus_token property for now.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-11-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
With the msi_list and the msi_domain properties now being at the
generic device level, it is starting to be relatively easy to offer
a generic way of providing non-PCI MSIs.
The two major hurdles with this idea are:
- Lack of global ID that identifies a device: this is worked around by
having a global ID allocator for each device that gets enrolled in
the platform MSI subsystem
- Lack of standard way to write the message in the generating device.
This is solved by mandating driver code to provide a write_msg
callback, so that everyone can have their own square wheel
Apart from that, the API is fairly straightforward:
- platform_msi_create_irq_domain creates an MSI domain that gets
tagged with DOMAIN_BUS_PLATFORM_MSI
- platform_msi_domain_alloc_irqs allocate MSIs for a given device,
populating the msi_list
- platform_msi_domain_free_irqs does what is written on the tin
[ tglx: Created a seperate struct platform_msi_desc and added
kerneldoc entries ]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-10-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
As for PCI, we're able to populate the msi_domain field at probe time,
provided that the device tree has an "msi-parent" property.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-9-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now that we can easily find which MSI domain a PCI device is
using, use dev_get_msi_domain as a way to retrieve the information.
The original code is still used as a fallback.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-8-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
A number of platforms do not need to use the msi-parent property,
as the host bridge itself provides the MSI controller.
Allow this configuration by performing an irq domain lookup based
on the host bridge node if it doesn't have a valid msi-parent property.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-7-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In order to populate the PCI host bridge msi_domain, use the
"msi-parent" attribute to lookup a corresponding irq domain.
If found, this is our MSI domain.
This gets plugged into the core PCI code.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-6-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
