Although mesh_rx_plink_frame() already checks that frames have enough
bytes for the action code plus another two bytes for capability/reason
code, it doesn't take into account that confirm frames also have an
additional two-byte aid. As a result, a corrupt frame could cause a
subsequent subtraction to wrap around to ill effect. Add another
check for this case.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to 802.11-2012 8.5.16.3.2 AID comes directly after the
capability bytes in mesh peering confirm frames. The existing
code, however, was adding a 2 byte offset to this location,
resulting in garbage data going out over the air. Remove the
offset to fix it.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With a basic Linux userspace, the messages "Calling CRDA to update
world regulatory domain" appears 10 times after boot every second or
so, followed by a final "Exceeded CRDA call max attempts. Not calling
CRDA". For those of us not having the corresponding userspace parts,
having those messages repeatedly displayed at boot time is a bit
annoying, so this commit reduces their log level to pr_debug().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "function" of the MPP driver was inherited from the GPIO driver, but the
differences between the two hardware blocks makes both the driver and the
device tree binding to be awkward.
Instead of overloading the "normal" function with various modes this patch
transposes the pinmux function to represent the three operating modes of the
MPP (digital, analog and current sink). The properties of pin pairing and DTEST
routing is moved to separate properties.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the MPP is configured for analog output the output level is selected by
the AOUT_CTL register, this patch makes it possible to control this.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The dedicated USB1 pins can be configured with pull-down and
for low power mode (suspend). Add support for this in the
pinctrl driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The function pinconf_dbg_config_print() only prints the configuration of
the 1st pin config in an array of pin configurations. Fix this so that
all pin configurations in the array are displayed.
There are a few places in the code where the pin configs are displayed
and so add a helper function to display the pin configs to simplify the
code.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The function pinconf_dbg_config_write() currently only supports configuring
a pin configuration mapping via the debugfs. Allow group mappings to also
be configured via the debugfs.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
User visible:
- Fix misplaced check for HAVE_SYNC_COMPARE_AND_SWAP_SUPPORT in
the auxtrace code, which made 'perf record' fail straight away
in some architectures, even when auxtrace wasn't involved. (Adrian Hunter)
Developer stuff:
- Really allow to specify custom CC, AR or LD (Alexey Brodkin)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fP9H
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Fix misplaced check for HAVE_SYNC_COMPARE_AND_SWAP_SUPPORT in
the auxtrace code, which made 'perf record' fail straight away
in some architectures, even when auxtrace wasn't involved. (Adrian Hunter)
- Really allow to specify custom CC, AR or LD (Alexey Brodkin)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If the vdev pointer == NULL, then just return.
This makes it easier for subdev drivers to use this function without having to
check if the sd->devnode pointer is NULL or not.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Interrupts for GPIOs 16 through 31 are enabled by bit 1 in the
"binten" register (offset 8). Previous versions of GPIO only
used bit 0, which enables GPIO 0-15 interrupts.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVouXcAAoJEHm+PkMAQRiGjWQIAJcfwb9z5U8jCR+FyvqqM//U
gzKdODPpwuJBa4IpQoCIZlT4wbGH3W0euuVKWk2zv9f+D/i5D/ZIAj0Wt5mjs1Z2
/uhEMnYskGHn7Q3HCQyyjPqTi6I4DnSiFS880xTQhsufXxtpDmVWETO1fyCvlt73
NU6Y0Y/Oe+tN5/Qp3wKLUaZMigiiBD5GviGQQNHtJ6UIorOCJnw5mYSx0dWPotIL
SYUno4WIR/48FKABUDxs13YK7JDLv3w4h8FimvY+cY6hKLZ9zUhFUCCE3OKXcpHQ
auAKhyi9YcqJxWvVUCl1gV8NmBefETp6zfWf07NBaDnFiNsfW+mqfO0mWwnOT5s=
=C7m8
-----END PGP SIGNATURE-----
Merge tag 'v4.2-rc2' into patchwork
Linux 4.2-rc2
We need to backport changeset 31f0245545, with fixes a bug at
include/linux/compiler.h that breaks sparse.
* tag 'v4.2-rc2': (221 commits)
Linux 4.2-rc2
Revert "drm/i915: Use crtc_state->active in primary check_plane func"
freeing unlinked file indefinitely delayed
fix a braino in ovl_d_select_inode()
9p: don't leave a half-initialized inode sitting around
tick/broadcast: Prevent NULL pointer dereference
selinux: fix mprotect PROT_EXEC regression caused by mm change
parisc: Fix some PTE/TLB race conditions and optimize __flush_tlb_range based on timing results
stifb: Implement hardware accelerated copyarea
nfit: add support for NVDIMM "latch" flag
nfit: update block I/O path to use PMEM API
tools/testing/nvdimm: add mock acpi_nfit_flush_address entries to nfit_test
tools/testing/nvdimm: fix return code for unimplemented commands
tools/testing/nvdimm: mock ioremap_wt
pmem: add maintainer for include/linux/pmem.h
Revert "Input: synaptics - allocate 3 slots to keep stability in image sensors"
arm64: entry32: remove pointless register assignment
MIPS: O32: Use compat_sys_getsockopt.
MIPS: c-r4k: Extend way_string array
MIPS: Pistachio: Support CDMM & Fast Debug Channel
...
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Buffers can be returned back to videobuf2 in driver's streamon handler. In
this case vb2_buffer_done() with buffer state VB2_BUF_STATE_QUEUED will
cause the driver's buf_queue vb2 operation to be called, queueing the same
buffer again only to be returned to videobuf2 using vb2_buffer_done() and so
on.
Add a new buffer state VB2_BUF_STATE_REQUEUEING which, when used as the
state argument to vb2_buffer_done(), will result in buffers queued to the
driver. Using VB2_BUF_STATE_QUEUED will leave the buffer to videobuf2, as it
was before "[media] vb2: allow requeuing buffers while streaming".
Fixes: ce0eff016f ("[media] vb2: allow requeuing buffers while streaming")
[mchehab@osg.samsung.com: fix warning: enumeration value 'VB2_BUF_STATE_REQUEUEING' not handled in switch]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v4.1
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
gpiod_get* functions mandatory and so allows to remove an ugly cpp hack
introduced in commit 39b2bbe3d7 (gpio: add flags argument to gpiod_get*()
functions) for v3.17-rc1.
The other nine commits fix the last remaining users of these functions that
don't pass flags yet. (Only etraxfs-uart wasn't fixed; this driver's use of the
gpiod functions needs fixing anyhow.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJVmj+OAAoJEMH8FHityuwJHGcH/A5bSLcdaFCMcrYceYD/odzR
X/mer/CcW/uWG0sUha2pZjT172szSrm0/Bk+SaY5Ub0c6ssCpKRGhtqZNVWWz44V
duRQGkYEFODHSed1XnKQyKwr6nLyhjmj8RuP5GokjcsBZyl4onj+NHgmpH5aQBYC
4NyFpIXcSS4jCwj4nsZu4Y2xLAgu/t5oVzqDheqTyZ9imgaR8hbyminKhN+wFfrI
FKukShQ5AQPVs7pGEqeY0wgJp+keOIYLukLwvgZw+S7MxixXaPiSK1Ez9DPY9CFo
f+NkDV6GIe4OAOGFsL9dCxR0sO6mF7C5PpYuDUBtISi3JHNAvW+Ri7FKPeSDikA=
=ixJj
-----END PGP SIGNATURE-----
Merge tag 'gpiod-flags-for-4.3' of git://git.pengutronix.de/git/ukl/linux into devel
The last patch in this series makes the flags parameter for the various
gpiod_get* functions mandatory and so allows to remove an ugly cpp hack
introduced in commit 39b2bbe3d7 (gpio: add flags argument to gpiod_get*()
functions) for v3.17-rc1.
The other nine commits fix the last remaining users of these functions that
don't pass flags yet. (Only etraxfs-uart wasn't fixed; this driver's use of the
gpiod functions needs fixing anyhow.)
As we now have generic infrastructure to support backtracing of other
CPUs in the system on lockups, we can start to implement this for ARM.
Initially, we add an IPI based implementation, as the GIC code needs
modification to support the generation of FIQ IPIs, and not all ARM
platforms have the ability to raise a FIQ in the non-secure world.
This provides us with a "best efforts" implementation in the absence
of FIQs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert x86 to use the generic nmi handler code which can be shared
between architectures.
Reviewed-and-tested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
x86s NMI backtrace implementation (for arch_trigger_all_cpu_backtrace())
is fairly generic in nature - the only architecture specific bits are
the act of raising the NMI to other CPUs, and reporting the status of
the NMI handler.
These are fairly simple to factor out, and produce a generic
implementation which can be shared between ARM and x86.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The driver does not free irq when snd_soc_register_codec returns error.
It does not return error when request irq failed, either.
Add return when request irq failed, and free_irq if
snd_soc_register_codec failed.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"ASoC: rt5645: Simplify rt5645_enable_push_button_irq" removes
the test that accessed rt5645->pdata.jd_mode (that test is now
done in rt5645_jack_detect only), so we do not need that
variable anymore.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dev_pm_ops variables are not modified after initialization in these
drivers, so make them const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes kernel panic on boot, if rt5645->codec is NULL when
rt5645_jack_detect_work is first called.
rt5645_jack_detect_work needs rt5645->codec to be initialized to setup
dapm pins. Also, reporting jack events is useless, as the jacks cannot
be set before the codec is ready.
Since we manually call the interrupt handler in
rt5645_set_jack_detect, the initial jack state will be reported
correctly, and dapm pins will be setup at that time.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It turns out to be rather tedious to test the NMI nesting code.
Make it easier: add a new CONFIG_DEBUG_ENTRY option that causes
the NMI handler to pre-emptively unmask NMIs.
With this option set, errors in the repeat_nmi logic or failures
to detect that we're in a nested NMI will result in quick panics
under perf (especially if multiple counters are running at high
frequency) instead of requiring an unusual workload that
generates page faults or breakpoints inside NMIs.
I called it CONFIG_DEBUG_ENTRY instead of CONFIG_DEBUG_NMI_ENTRY
because I want to add new non-NMI checks elsewhere in the entry
code in the future, and I'd rather not add too many new config
options or add this option and then immediately rename it.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently, "NMI executing" is one the first time an outermost
NMI hits repeat_nmi and zero thereafter. Change it to be zero
each time for consistency.
This is intended to help NMI handling fail harder if it's buggy.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Replace LEA; MOV with an equivalent SUB. This saves one
instruction.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We have a tricky bug in the nested NMI code: if we see RSP
pointing to the NMI stack on NMI entry from kernel mode, we
assume that we are executing a nested NMI.
This isn't quite true. A malicious userspace program can point
RSP at the NMI stack, issue SYSCALL, and arrange for an NMI to
happen while RSP is still pointing at the NMI stack.
Fix it with a sneaky trick. Set DF in the region of code that
the RSP check is intended to detect. IRET will clear DF
atomically.
( Note: other than paravirt, there's little need for all this
complexity. We could check RIP instead of RSP. )
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Check the repeat_nmi .. end_repeat_nmi special case first. The
next patch will rework the RSP check and, as a side effect, the
RSP check will no longer detect repeat_nmi .. end_repeat_nmi, so
we'll need this ordering of the checks.
Note: this is more subtle than it appears. The check for
repeat_nmi .. end_repeat_nmi jumps straight out of the NMI code
instead of adjusting the "iret" frame to force a repeat. This
is necessary, because the code between repeat_nmi and
end_repeat_nmi sets "NMI executing" and then writes to the
"iret" frame itself. If a nested NMI comes in and modifies the
"iret" frame while repeat_nmi is also modifying it, we'll end up
with garbage. The old code got this right, as does the new
code, but the new code is a bit more explicit.
If we were to move the check right after the "NMI executing"
check, then we'd get it wrong and have random crashes.
( Because the "NMI executing" check would jump to the code that would
modify the "iret" frame without checking if the interrupted NMI was
currently modifying it. )
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I found the nested NMI documentation to be difficult to follow.
Improve the comments.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Returning to userspace is tricky: IRET can fail, and ESPFIX can
rearrange the stack prior to IRET.
The NMI nesting fixup relies on a precise stack layout and
atomic IRET. Rather than trying to teach the NMI nesting fixup
to handle ESPFIX and failed IRET, punt: run NMIs that came from
user mode on the normal kernel stack.
This will make some nested NMIs visible to C code, but the C
code is okay with that.
As a side effect, this should speed up perf: it eliminates an
RDMSR when NMIs come from user mode.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that do_nmi saves CR2, we don't need to save it in asm.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
32-bit kernels handle nested NMIs in C. Enable the exact same
handling on 64-bit kernels as well. This isn't currently
necessary, but it will become necessary once the asm code starts
allowing limited nesting.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The GICv3 ITS architecture allows a given [DevID, EventID] pair to be
translated to a [LPI, Collection] pair, where DevID is the device writing
the MSI, EventID is the payload being written, LPI is the actual
interrupt number, and Collection is roughly equivalent to a target CPU.
Each LPI can be mapped to a separate collection, but the ITS driver
insists on maintaining the collection on a device basis, instead of doing
it on a per interrupt basis.
This is obviously flawed, and this patch fixes it by adding a per interrupt
index that indicates which collection number is in use.
Reported-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: stable@vger.kernel.org # 4.1, 4.0
Link: http://lkml.kernel.org/r/1437126402-11677-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The EP93xx SoC has a framebuffer driver, let's add this to the
defconfig so we can have graphics working out of the box.
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Several boards can make use of the DMA engine on the EP93xx
so let's enable this by default in the defconfig.
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some of the EP93xx boards have I2C devices on bit-banged GPIO
I2C, so add this to the defconfig.
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The EP93xx has two designated LEDs (not always connected): a
green and a red one. These are registered in the core, so let's
enable the driver and some triggers.
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SIM.ONE has a MMC card connected to the SPI host. This card
usually hosts an EXT4 root file system. Enable these options in
the defconfig so the default ompiled kernel will work
out-of-the-box.
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With PATCH_PHYS_TO_VIRT we can support all EP93xx variants
in a single image, so enable all board variants in the defconfig
for simplicity and build coverage.
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Let's set the EP93xx to NO_HZ mode and activate the high-res
timers now that we have GENERIC_CLOCKEVENTS.
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPI host on the SIM.ONE is used for the MMC/SD card and
will badly need this turbo boost.
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add I2S audio support to the vision_ep9307 system.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Enable the 'use_dma' flag in the SPI platform data to improve the speed
of the mmc_spi driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It doesn't hurt to add this random stuff into the entropy pool
as is custom to do with device-unique numbers.
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ARM_PATCH_PHYS_VIRT option makes the ep93xx memory configuration
options obsolete.
This allows support for all the ep93xx variations to be built into a
single kernel.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When refactoring the EP93xx timer some of the documentation
git out of date. Update it.
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A firmware bug in some touchpads causes the F01 interrupt enable register
to be cleared on reset. This register controls which RMI functions generate
interrupts and when it is cleared, the touchpad stops reporting all data.
This patch looks for the cleared F01 control register and writes the
correct value based on interrupt mask computed while scanning the PDT.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=91102
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The resend mechanism happily calls the interrupt handler of interrupts
which are marked IRQ_NESTED_THREAD from softirq context. This can
result in crashes because the interrupt handler is not the proper way
to invoke the device handlers. They must be invoked via
handle_nested_irq.
Prevent the resend even if the interrupt has no valid parent irq
set. Its better to have a lost interrupt than a crashing machine.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Allocated input devices should not use the 'pen_name' by default since
we do not know at that point in time if that is an appropriate choice
of name. Instead, use the (tool-agnostic) name that is stored in the
device's 'wacom_features' structure. This also has the nice side-effect
of requring us to be explicit about the naming of the pen device, as
we already are for touch and pad devices.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>