This patch updates the current channel to 11. This is the default
value on reset.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
CC2520 has the default 0dBm transmit power level on reset.
This patch update initial value of transmit power with 0dBm value.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Cc: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for seeting tx power values for cc2520
and also for the combination of CC2520-CC2591.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Cc: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes tha way of handling of cc2591-cc2520 combination
by moving amplified variable from platform data to private data.
This will be useful in other sections like tx power support.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Cc: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Initially we dont have the tx power settings from the user-space.
Now we have the support for seeting the tx power level.
So lets use the default tx power setting for the radio.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Cc: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Atusb uses the at86rf231 transceiver so we can use the same calculation
for txpower settings for it.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With this function we can set individual bits in the registers if needed.
With the old SR_VALUE macro we could only set one bit in the register
which was ok for some scenarios but not for all. With this subreg write
function we can now set more bits defined by the mask while not touching
the rest.
We start using it for the current SR_VALUE use case and will use it more
in upcoming patches.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Refuse to allow setting an EUI-64 group address as an interface
address, as those are not valid station addresses.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently, ieee802154_random_extended_addr() has a 50% chance of
generating a group (multicast) address, while this function is used
for generating station addresses (which can't be group addresses)
for interfaces that don't have a hardware-provided address.
Also, in case get_random_bytes() generates the EUI-64 address
00:00:00:00:00:00:00:00 (extremely unlikely), which is an invalid
address, ieee802154_random_extended_addr() reacts by changing it
to 01:00:00:00:00:00:00:00, which is an invalid station address as
well, as it is a group address.
This patch changes the address generation procedure to grab eight
random bytes, treat that as an EUI-64, and then clear the Group
address bit and set the Locally Administered bit, which is in
line with how eth_random_addr() generates random EUI-48s.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hppfs (honeypot procfs) was an attempt to use UML as honeypot.
It was never stable nor in heavy use.
As Al Viro and Christoph Hellwig pointed some major issues out
it is better to let it die.
Signed-off-by: Richard Weinberger <richard@nod.at>
syscall() is implemented in libc.so/a (e.g. for glibc, in "syscall.o"),
so for normal ".o" files, it is undefined, neither can be found within
kernel wide, so will break modpost.
Since ".o" files is OK, can simply export 'syscall' symbol, let modpost
know about that, then can fix this issue.
The related error (with allmodconfig under um):
MODPOST 1205 modules
ERROR: "syscall" [fs/hostfs/hostfs.ko] undefined!
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
When declaring __syscall_stub_start, use the same type in UML userspace
code as in arch/um/include/asm/sections.h.
While at it, also declare batch_syscall_stub as char[].
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
The linker script defines some variables which are declared either with
type char[] in include/asm-generic/sections.h or with a meaningless
integer type in arch/um/include/asm/sections.h.
Fix this inconsistency by declaring every variable char[].
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
arch/um/kernel/dyn.lds.S and arch/um/kernel/uml.lds.S define some
UML-specific symbols. These symbols are used in the kernel part of UML
with extern declarations.
Move these declarations to a new header, asm/sections.h, like other
architectures do.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
- checkpatch fixes
- code cleanup
- debugfs component is now compiled only if DEBUG_FS is selected
- update copyright years
- disable by default not-so-user-safe features
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=2UBm
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
Included changes:
- checkpatch fixes
- code cleanup
- debugfs component is now compiled only if DEBUG_FS is selected
- update copyright years
- disable by default not-so-user-safe features
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally the program attachment place (like sockets, qdiscs) takes
care of rcu protection and calls bpf_prog_put() after a grace period.
The programs stored inside prog_array may not be attached anywhere,
so prog_array needs to take care of preserving rcu protection.
Otherwise bpf_tail_call() will race with bpf_prog_put().
To solve that introduce bpf_prog_put_rcu() helper function and use
it in 3 places where unattached program can decrement refcnt:
closing program fd, deleting/replacing program in prog_array.
Fixes: 04fd61ab36 ("bpf: allow bpf programs to tail-call other bpf programs")
Reported-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
VT202x codecs seem requiring some delay after the resume D0 power
transition for making the jack detection working again. Without the
delay soon after D0, the jack is always detected as unplugged.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98921
Signed-off-by: Takashi Iwai <tiwai@suse.de>
K. Y. Srinivasan says:
====================
hv_netvsc: Implement NUMA aware memory allocation
Allocate both receive buffer and send buffer from the NUMA node assigned to the
primary channel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate the receive bufer from the NUMA node assigned to the primary
channel.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The header file, include/linux/serial_8250.h, contains references to
UART_LSR_BRK_ERROR_BITS and UART_MSR_ANY_DELTA that are defined in
<linux/serial_reg.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix compilation error in fsl ehci drv because ehci_reset()
and ehci_adjust_port_wakeup_flags() were not exported, and
are used when PM is enabled
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue that sometimes this controller is not able
to complete the Control write status stage.
This driver should enable DCPCTR.CCPL and PID_BUF to complete the status
stage. However, if this driver detects the ctrl_stage interruption first
before the control write data is received, this driver will clear the
PID_BUF wrongly in the usbhsf_pio_try_pop(). To avoid this issue, this
patch doesn't clear the PID_BUF in the usbhsf_pio_try_pop().
(Since also the privious code doesn't disable the PID_BUF after a control
transfer was finished, this patch doesn't have any side efforts.)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue for control write. When usbhsf_prepare_pop()
is called after this driver called a gadget setup function, this controller
doesn't receive the control write data. So, this patch adds a code to clear
the fifo for control write in usbhsf_prepare_pop().
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove automatic variable 'err' in register_netevent_notifier() and
return the result of atomic_notifier_chain_register() directly.
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next, they are:
1) default CONFIG_NETFILTER_INGRESS to y for easier compile-testing of all
options.
2) Allow to bind a table to net_device. This introduces the internal
NFT_AF_NEEDS_DEV flag to perform a mandatory check for this binding.
This is required by the next patch.
3) Add the 'netdev' table family, this new table allows you to create ingress
filter basechains. This provides access to the existing nf_tables features
from ingress.
4) Kill unused argument from compat_find_calc_{match,target} in ip_tables
and ip6_tables, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: systemport: misc improvements
These patches are highly inspired by changes from Petri on bcmgenet, last patch
is a misc fix that I had pending for a while, but is not a candidate for 'net'
at this point.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Occasionnaly we may get oversized packets from the hardware which exceed
the nomimal 2KiB buffer size we allocate SKBs with. Add an early check
which drops the packet to avoid invoking skb_over_panic() and move on to
processing the next packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for USB controller version-2.5 used in
T4240 rev2.0, T1024, T1040, T2080, LS1021A
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check IP version 2.4 for multi port host USB controller and
return FSL_USB_VER_2_4 macro
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix USB 3.0 devices lost in NOTATTACHED state after a hub port reset.
Dissolve the function hub_port_finish_reset() completely and divide the
actions to be taken into those which need to be done after each reset
attempt and those which need to be done after the full procedure is
complete, and place them in the appropriate places in hub_port_reset().
Also, remove an unneeded forward declaration of hub_port_reset().
Verbose Problem Description:
USB 3.0 devices may be "lost for good" during a hub port reset.
This makes Linux unable to boot from USB 3.0 devices in certain
constellations of host controllers and devices, because the USB device is
lost during initialization, preventing the rootfs from being mounted.
The underlying problem is that in the affected constellations, during the
processing inside hub_port_reset(), the hub link state goes from 0 to
SS.inactive after the initial reset, and back to 0 again only after the
following "warm" reset.
However, hub_port_finish_reset() is called after each reset attempt and
sets the state the connected USB device based on the "preliminary" status
of the hot reset to USB_STATE_NOTATTACHED due to SS.inactive, yet when
the following warm reset is complete and hub_port_finish_reset() is
called again, its call to set the device to USB_STATE_DEFAULT is blocked
by usb_set_device_state() which does not allow taking USB devices out of
USB_STATE_NOTATTACHED state.
Thanks to Alan Stern for guiding me to the proper solution and how to
submit it.
Link: http://lkml.kernel.org/r/trinity-25981484-72a9-4d46-bf17-9c1cf9301a31-1432073240136%20()%203capp-gmx-bs27
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is used to call in early version of linux kernel in order
to find out the interface used by a usb device. But now it's use is
completely abolished. So,it would be relevant to remove this obselete
function from kernel mainline.
Signed-off-by: Abhishek Bist <ishubist@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, bcm_sysport_desc_rx() calls bcm_sysport_rx_refill() at the end of Rx
packet processing loop, after the current Rx packet has already been passed to
napi_gro_receive(). However, bcm_sysport_rx_refill() might fail to allocate a new
Rx skb, thus leaving a hole on the Rx queue where no valid Rx buffer exists.
To eliminate this situation:
1. Rewrite bcm_sysport_rx_refill() to retain the current Rx skb on the
Rx queue if a new replacement Rx skb can't be allocated and DMA-mapped.
In this case, the data on the current Rx skb is effectively dropped.
2. Modify bcm_sysport_desc_rx() to call bcm_sysport_rx_refill() at the
top of Rx packet processing loop, so that the new replacement Rx skb is
already in place before the current Rx skb is processed.
This is loosely inspired from d6707bec59 ("net: bcmgenet: rewrite
bcmgenet_rx_refill()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a 1:1 mapping between the software maintained control block in
priv->rx_cbs and the buffer address in priv->rx_bds, such that there is
no need to keep computing the buffer address when refiling a control
block.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete jump to a label on the next line, when that label is not
used elsewhere.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier l;
@@
-if (...) goto l;
-l:
// </smpl>
Also remove the unnecessary ret variable.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera says:
====================
bna: misc bugfixes
These patches fix several bugs found during device initialization debugging.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug in the driver initialization causes soft-lockup if firmware
initialization timeout is reached. Polling function bfa_ioc_poll_fwinit()
incorrectly calls bfa_nw_iocpf_timeout() when the timeout is reached.
The problem is that bfa_nw_iocpf_timeout() calls again
bfa_ioc_poll_fwinit()... etc. The bfa_ioc_poll_fwinit() should directly
send timeout event for iocpf and the same should be done if firmware
download into HW fails.
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver starts iocpf timer prior bnad_ioceth_enable() call and this is
unreasonable. This piece of code probably originates from Brocade/Qlogic
out-of-box driver during initial import into upstream. This driver uses
only one timer and queue to implement multiple timers and this timer is
started at this place. The upstream driver uses multiple timers instead
of this.
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware required by bna is stored in appropriate files as sequence
of LE32 integers. After loading by request_firmware() they need to be
byte-swapped on big-endian arches. Without this conversion the NIC
is unusable on big-endian machines.
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment stating that xhci_setup_device() is protected by the address
mutex is not true since
commit 6fecd4f2a5 ("USB: separate usb_address0 mutexes for each bus")
as xhci handles two buses.
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the xhci driver from bluntly setting the transferred length to 0 if
we get a STALL on anything else than the data stage of a control transfer.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We used to write the root port state changes in turn for every port,
sleeping 20ms after every port state change. Suspended usb2 ports need
two state changes, taking minimun 40ms per port.
Now instead poll the Port Link State Change (PLC) bit as
the state change to U0 will set this bit.
Suspended usb2 ports still need the extra 20ms delay, but we now change
all the port states at once so we only need to sleep 20ms once all together
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the OTG case, the controller might not yet have been
added or is removed before the system suspends.
Assign xhci->main_hcd during probe to prevent NULL
pointer de-reference in xhci_suspend/resume().
Use the hcd->state flag to check if HCD is halted
and if that is so do nothing for xhci_suspend/resume().
[Only for xhci-plat devices, pci devices need it in gen_setup -Mathias]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem seems to be that if a new device is detected
while we have already removed the shared HCD, then many of the
xhci operations (e.g. xhci_alloc_dev(), xhci_setup_device())
hang as command never completes.
I don't think XHCI can operate without the shared HCD as we've
already called xhci_halt() in xhci_only_stop_hcd() when shared HCD
goes away. We need to prevent new commands from being queued
not only when HCD is dying but also when HCD is halted.
The following lockup was detected while testing the otg state
machine.
[ 178.199951] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 178.205799] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 178.214458] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x00010010
[ 178.223619] xhci-hcd xhci-hcd.0.auto: irq 400, io mem 0x48890000
[ 178.230677] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 178.237796] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 178.245358] usb usb1: Product: xHCI Host Controller
[ 178.250483] usb usb1: Manufacturer: Linux 4.0.0-rc1-00024-g6111320 xhci-hcd
[ 178.257783] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 178.267014] hub 1-0:1.0: USB hub found
[ 178.272108] hub 1-0:1.0: 1 port detected
[ 178.278371] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 178.284171] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 178.294038] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 178.301183] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 178.308776] usb usb2: Product: xHCI Host Controller
[ 178.313902] usb usb2: Manufacturer: Linux 4.0.0-rc1-00024-g6111320 xhci-hcd
[ 178.321222] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 178.329061] hub 2-0:1.0: USB hub found
[ 178.333126] hub 2-0:1.0: 1 port detected
[ 178.567585] dwc3 48890000.usb: usb_otg_start_host 0
[ 178.572707] xhci-hcd xhci-hcd.0.auto: remove, state 4
[ 178.578064] usb usb2: USB disconnect, device number 1
[ 178.586565] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 178.592585] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 178.597924] usb usb1: USB disconnect, device number 1
[ 178.603248] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 190.597337] INFO: task kworker/u4:0:6 blocked for more than 10 seconds.
[ 190.604273] Not tainted 4.0.0-rc1-00024-g6111320 #1058
[ 190.610228] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 190.618443] kworker/u4:0 D c05c0ac0 0 6 2 0x00000000
[ 190.625120] Workqueue: usb_otg usb_otg_work
[ 190.629533] [<c05c0ac0>] (__schedule) from [<c05c10ac>] (schedule+0x34/0x98)
[ 190.636915] [<c05c10ac>] (schedule) from [<c05c1318>] (schedule_preempt_disabled+0xc/0x10)
[ 190.645591] [<c05c1318>] (schedule_preempt_disabled) from [<c05c23d0>] (mutex_lock_nested+0x1ac/0x3fc)
[ 190.655353] [<c05c23d0>] (mutex_lock_nested) from [<c046cf8c>] (usb_disconnect+0x3c/0x208)
[ 190.664043] [<c046cf8c>] (usb_disconnect) from [<c0470cf0>] (_usb_remove_hcd+0x98/0x1d8)
[ 190.672535] [<c0470cf0>] (_usb_remove_hcd) from [<c0485da8>] (usb_otg_start_host+0x50/0xf4)
[ 190.681299] [<c0485da8>] (usb_otg_start_host) from [<c04849a4>] (otg_set_protocol+0x5c/0xd0)
[ 190.690153] [<c04849a4>] (otg_set_protocol) from [<c0484b88>] (otg_set_state+0x170/0xbfc)
[ 190.698735] [<c0484b88>] (otg_set_state) from [<c0485740>] (otg_statemachine+0x12c/0x470)
[ 190.707326] [<c0485740>] (otg_statemachine) from [<c0053c84>] (process_one_work+0x1b4/0x4a0)
[ 190.716162] [<c0053c84>] (process_one_work) from [<c00540f8>] (worker_thread+0x154/0x44c)
[ 190.724742] [<c00540f8>] (worker_thread) from [<c0058f88>] (kthread+0xd4/0xf0)
[ 190.732328] [<c0058f88>] (kthread) from [<c000e810>] (ret_from_fork+0x14/0x24)
[ 190.739898] 5 locks held by kworker/u4:0/6:
[ 190.744274] #0: ("%s""usb_otg"){.+.+.+}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.752799] #1: ((&otgd->work)){+.+.+.}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.761326] #2: (&otgd->fsm.lock){+.+.+.}, at: [<c048562c>] otg_statemachine+0x18/0x470
[ 190.769934] #3: (usb_bus_list_lock){+.+.+.}, at: [<c0470ce8>] _usb_remove_hcd+0x90/0x1d8
[ 190.778635] #4: (&dev->mutex){......}, at: [<c046cf8c>] usb_disconnect+0x3c/0x208
[ 190.786700] INFO: task kworker/1:0:14 blocked for more than 10 seconds.
[ 190.793633] Not tainted 4.0.0-rc1-00024-g6111320 #1058
[ 190.799567] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 190.807783] kworker/1:0 D c05c0ac0 0 14 2 0x00000000
[ 190.814457] Workqueue: usb_hub_wq hub_event
[ 190.818866] [<c05c0ac0>] (__schedule) from [<c05c10ac>] (schedule+0x34/0x98)
[ 190.826252] [<c05c10ac>] (schedule) from [<c05c4e40>] (schedule_timeout+0x13c/0x1ec)
[ 190.834377] [<c05c4e40>] (schedule_timeout) from [<c05c19f0>] (wait_for_common+0xbc/0x150)
[ 190.843062] [<c05c19f0>] (wait_for_common) from [<bf068a3c>] (xhci_setup_device+0x164/0x5cc [xhci_hcd])
[ 190.852986] [<bf068a3c>] (xhci_setup_device [xhci_hcd]) from [<c046b7f4>] (hub_port_init+0x3f4/0xb10)
[ 190.862667] [<c046b7f4>] (hub_port_init) from [<c046eb64>] (hub_event+0x704/0x1018)
[ 190.870704] [<c046eb64>] (hub_event) from [<c0053c84>] (process_one_work+0x1b4/0x4a0)
[ 190.878919] [<c0053c84>] (process_one_work) from [<c00540f8>] (worker_thread+0x154/0x44c)
[ 190.887503] [<c00540f8>] (worker_thread) from [<c0058f88>] (kthread+0xd4/0xf0)
[ 190.895076] [<c0058f88>] (kthread) from [<c000e810>] (ret_from_fork+0x14/0x24)
[ 190.902650] 5 locks held by kworker/1:0/14:
[ 190.907023] #0: ("usb_hub_wq"){.+.+.+}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.915454] #1: ((&hub->events)){+.+.+.}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.924070] #2: (&dev->mutex){......}, at: [<c046e490>] hub_event+0x30/0x1018
[ 190.931768] #3: (&port_dev->status_lock){+.+.+.}, at: [<c046eb50>] hub_event+0x6f0/0x1018
[ 190.940558] #4: (&bus->usb_address0_mutex){+.+.+.}, at: [<c046b458>] hub_port_init+0x58/0xb10
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't set xhci->shared_hcd to NULL in xhci_stop() as we have
still not de-allocated it. It was resulting in a NULL pointer
de-reference if usb_add/remove_hcd() is called repeatedly.
We want repeated add/remove to work for the OTG use case.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>