The current "We only connect the NOR to this controller now." text
is not very clear, so explain it better by saying that generic SPI
is not supported by SPI_FSL_QUADSPI and only SPI NOR is.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add SPI-NOR driver for the SPI Flash Interface (SPIFI)
controller that is found on newer NXP MCU devices.
The controller supports serial SPI Flash devices with 1-, 2-
and 4-bit width in either SPI mode 0 or 3. The controller
can operate in either command or memory mode. In memory mode
the Flash is exposed as normal memory and can be directly
accessed by the CPU.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add device tree binding documentation for the SPI Flash Interface
(SPIFI) found on NXP LPC18xx and LPC43xx devies.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The initial buffer is used for the initial commands used to detect
a flash device (STATUS, READID and PARAM).
ONFI param page is 256 bytes, and there are three redundant copies
to be read. JEDEC param page is 512 bytes, and there are also three
redundant copies to be read. Hence this buffer should be at least
512 x 3. This commits rounds the buffer size to 2048.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When using reverse polarity for clock (spi-cpol) on a device
the clock line gets altered after chip-select has been asserted
resulting in an additional clock beat, which confuses hardware.
This did not show when using native-CS, as the same register
is used to control cs as well as polarity, so the changes came
into effect at the same time. Unfortunately this is not true
with gpio-cs.
To avoid this situation this patch moves the setup of polarity
(spi-cpol and spi-cpha) outside of the chip-select into
prepare_message, which is run prior to asserting chip-select.
Also fixes resetting 3-wire mode after use of rx-mode, so that
a 3-Wire sequence TX, RX, TX works as well (right now it runs
TX, RX, RX instead)
Reported-by: Noralf Tronnes <noralf@tronnes.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This function is missing a check if map->bus->write is implemented. If
it is not implemented arbitrary raw writes are not possible.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull timer fix from Ingo Molnar:
"A single clocksource driver suspend/resume fix"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents/drivers/sh_cmt: Only perform clocksource suspend/resume if enabled
regulator_disable of pbias always writes '0' to the enable_reg.
However actual disable value of pbias regulator is not always '0'.
Fix it by populating the disable_val in pbias_reg_info for the
various platforms and assign it to the disable_val of
pbias regulator descriptor. This will be used by
regulator_disable_regmap while disabling pbias regulator.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Pull locking fix from Ingo Molnar:
"A single fix for a locking self-test crash"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/pvqspinlock: Fix kernel panic in locking-selftest
When a BTT is instantiated on a namespace it must validate the namespace
uuid matches the 'parent_uuid' stored in the btt superblock. This
property enforces that changing the namespace UUID invalidates all
former BTT instances on that storage. For "IO namespaces" that don't
have a label or UUID, the parent_uuid is set to zero, and this
validation is skipped. For such cases, old BTTs have to be invalidated
by forcing the namespace to raw mode, and overwriting the BTT info
blocks.
Based on a patch by Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use arena_is_valid as a common routine for checking the validity of an
info block from both discover_arenas, and nd_btt_probe.
As a result, don't check for validity of the BTT's UUID, and lbasize.
The checksum in the BTT info block guarantees self-consistency, and when
we're called from nd_btt_probe, we don't have a valid uuid or lbasize
available to check against.
Also cleanup to return a bool instead of an int.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Consolidate the parameters passed to arena_is_valid into just nd_btt,
and an info block to increase re-usability.
Similarly, btt_arena_write_layout doesn't need to be passed a uuid, as
it can be obtained from arena->nd_btt.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pull drm fixes from Dave Airlie:
"Back from holidays, found these in the cracks: one nouveau revert, one
vmwgfx locking fix and a bunch of exynos fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
Revert "drm/nouveau/fifo/gk104: kick channels when deactivating them"
drm/vmwgfx: Fix execbuf locking issues
drm/exynos/fimc: fix runtime pm support
drm/exynos/mixer: always update INT_EN cache
drm/exynos/mixer: correct vsync configuration sequence
drm/exynos/mixer: fix interrupt clearing
drm/exynos/hdmi: fix edid memory leak
drm/exynos: gsc: fix wrong bitwise operation for swap detection
Kill arch_memremap_pmem() and just let the architecture specify the
flags to be passed to memremap(). Default to writethrough by default.
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for deprecating ioremap_cache() convert its usage in
visorbus to memremap.
Cc: Benjamin Romer <benjamin.romer@unisys.com>
Cc: David Kershner <david.kershner@unisys.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Existing users of ioremap_cache() are mapping memory that is known in
advance to not have i/o side effects. These users are forced to cast
away the __iomem annotation, or otherwise neglect to fix the sparse
errors thrown when dereferencing pointers to this memory. Provide
memremap() as a non __iomem annotated ioremap_*() in the case when
ioremap is otherwise a pointer to cacheable memory. Empirically,
ioremap_<cacheable-type>() call sites are seeking memory-like semantics
(e.g. speculative reads, and prefetching permitted).
memremap() is a break from the ioremap implementation pattern of adding
a new memremap_<type>() for each mapping type and having silent
compatibility fall backs. Instead, the implementation defines flags
that are passed to the central memremap() and if a mapping type is not
supported by an arch memremap returns NULL.
We introduce a memremap prototype as a trivial wrapper of
ioremap_cache() and ioremap_wt(). Later, once all ioremap_cache() and
ioremap_wt() usage has been removed from drivers we teach archs to
implement arch_memremap() with the ability to strictly enforce the
mapping type.
Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Some kernel-doc sections are included in multiple DocBook files. This
means the mandocs target will generate the same manual page multiple
times with different metadata (author name/address and manual title,
taken from the including DocBook file). If it's invoked in a parallel
build, the output is non-determinstic.
Build the manual pages in a separate subdirectory per DocBook file,
then sort and de-duplicate when installing them (which is serialised).
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[jc: fixed conflicts with the docs tree]
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
pm_runtime_get_sync() increments the runtime PM usage counter even the
call returns an error code. Thus a pairing decrement is needed on the
error handling path to keep the counter balanced.
Signed-off-by: Junjie Mao <junjie.mao@enight.me>
Signed-off-by: Mark Brown <broonie@kernel.org>
The readable registers are in continuous ranges: 0x01 ~ 0x03, 0x05 ~ 0x5f.
Use case range syntax makes the code shorter with better readability when
we have a large number of continuous switch cases.
No functional change with this patch.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The readable registers are in continuous range: 0x01 ~ 0x2e.
Use case range syntax makes the code shorter with better readability when
we have a large number of continuous switch cases.
No functional change with this patch.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The readable registers are in continuous range: 0x01 ~ 0x34.
Use case range syntax makes the code shorter with better readability when
we have a large number of continuous switch cases.
No functional change with this patch.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use case range syntax makes the code shorter with better readability when
we have a large number of continuous switch cases.
Below are the summary of readable/volatile/precious registers.
The readable registers:
0x01 ~ 0x0D, 0x0F ~ 0x1C
The volatile registers:
0x01 ~ 0x05, 0x15 ~ 0x18
The precious registers:
0x15 ~ 0x18
No functional change with this patch.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use managed resource functions devm_clk_put and
devm_snd_soc_register_component to simplify error handling.
To be compatible with the change various gotos are replaced
with direct returns, and unneeded labels are dropped.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ssm4567 has sensing circuitry that can be used to monitor the current
and voltage on the speaker amplifier output has well as the VBAT input.
This data can be output over the I2S interface so it can be processed by a
DSP or similar.
This patch adds the sense capture output stream to the CODEC DAI as well as
DAPM widgets that ensure that the sensing circuitry is powered up when the
capture stream is active.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We were storing the vfs_getname payload (i.e. ptr->string) into
the trace wide storage area (struct trace), so that we could use the
last payload when setting up the fd->pathname per thread tables, oops,
not a good idea for multi cpu tracing sessions...
Fix it by moving it to the per thread area (struct thread_trace).
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-3j05ttqyaem7kh7oubvr1keo@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
An OEM may request increased I_boost beyond the recommended values
by specifying an I_boost value to be applied to all swing entries for
a port. These override values are specified in VBT.
v2: rebase and remove unused iboost_bit variable
Issue: VIZ-5676
Signed-off-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-intel-fixes because a bunch of atomic patch backporting
we had to do lead to horrible conflicts.
Conflicts:
drivers/gpu/drm/drm_crtc.c
Just a bit of context conflict between -next and -fixes.
drivers/gpu/drm/i915/intel_atomic.c
drivers/gpu/drm/i915/intel_display.c
Atomic conflicts, always pick the code from -next.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
There is currently conflicting documentation on which steppings the
workaround is needed, up to C vs. forever. However there is post-C
stepping hardware that doesn't report port presence on DDI A, leading to
black screen on eDP. Assume the strap isn't connected, and try to enable
DDI A on these machines. (We'll still check the VBT for the info in DDI
init.)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DP spec requires the checksum of the last block read to be written
when replying to TEST_EDID_READ. This patch fixes the current code
to do the same.
v2: removed loop for jumping blocks and performed direct addition
as recommended by Daniel
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prevent leaking the if scoping by containing the WA_REG
macro inside its own scope.
Reported-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we encounter an allocation failure during ppggt creation (trivial
even with 16Gib+ RAM!), we need to remove the dead context from the
fpriv->context_idr along with the references.
gem_exec_ctx: page allocation failure: order:0, mode:0x8004
CPU: 3 PID: 27272 Comm: gem_exec_ctx Tainted: G W 4.2.0-rc5+ #37
0000000000000000 ffff880086ff7a78 ffffffff816b947a ffff88041ed90038
0000000000008004 ffff880086ff7b08 ffffffff8114b1a5 ffff880086ff7ac8
ffffffff8108d848 0000000000000000 ffffffff81ce84b8 0000000000000000
Call Trace:
[<ffffffff816b947a>] dump_stack+0x45/0x57
[<ffffffff8114b1a5>] warn_alloc_failed+0xd5/0x120
[<ffffffff8108d848>] ? __wake_up+0x48/0x60
[<ffffffff8114e0ed>] __alloc_pages_nodemask+0x73d/0x8e0
[<ffffffffc0472238>] ? i915_gem_execbuffer2+0x148/0x240 [i915]
[<ffffffffc0474240>] __setup_page_dma+0x30/0x110 [i915]
[<ffffffffc0477f61>] gen8_ppgtt_init+0x31/0x2f0 [i915]
[<ffffffffc04785e0>] i915_ppgtt_init+0x30/0x80 [i915]
[<ffffffffc0478928>] i915_ppgtt_create+0x48/0xc0 [i915]
[<ffffffffc046c9c2>] i915_gem_create_context+0x1c2/0x390 [i915]
[<ffffffffc046d9cb>] i915_gem_context_create_ioctl+0x5b/0xa0 [i915]
leading to an oops in i915_gem_context_close. Also note that this
benchmark should not be running out of memory in the first place...
Testcase: igt/benchmark/gem_exec_ctx -b create # ppgtt >= 2
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The IOMMU for Intel graphics has historically had many issues resulting
in random GPU hangs. Lets include its status when capturing the GPU hang
error state for post-mortem analysis.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If idle to active bit is set, the rest of the fields
in CSQ are not valid.
Bail out early if this is the case in order to prevent
rest of the loop inspecting stale values.
This was found by Bspec/code inspection. Doesn't seem to fix any of
the known issues.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
[danvet: Add note about how this was found.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no correspondent Aux channel for DDI-E.
So we need to rely on VBT to let us know witch one
is being used instead.
v2: Removing some trailing spaces and giving proper
credit to Xiong that added a nice way to avoid port
conflicts by setting supports_dp = 0 when using
equivalent aux for DDI-E.
Credits-to: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I started digging this when I noticed that the BDW code was just
reserving 1mb by coincidence since it was reading reserved fields.
Then I noticed we didn't have any values set for SNB and earlier, and
that the HSW sizes were wrong. After that, I noticed that the reserved
area has a specific start, and may not exactly end where the stolen
memory ends. I also noticed the base pointer can be zero. So I decided
to just write a single patch fixing everything instead of 20 patches
that would be much harder to review.
This patch may solve random stolen memory corruption/problems on
almost all platforms. Notice that since this is always dealing with
the top of the stolen memory, the problems are not so easy to
reproduce - especially since FBC is still disabled by default.
One of the major differences of this patch is that we now look at both
the size and base address. By only looking at the size we were
assuming that the reserved area was always at the very top of
stolen, which is not always true.
After we merge the patch series that allows user space to allocate
stolen memory we'll be able to write IGT tests that maybe catch the
bugs fixed by this patch.
v2:
- s/BIOS reserved/stolen reserved/g (Chris)
- Don't DRM_ERROR if we can't do anything about it (Chris)
- Improve debug messages (Chris).
- Use the gen7 version instead of gen6 on HSW. Tom found some
documentation problems, so I think with gen7 we're on the safer
side (Tom).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This register needs to be updated with masked writes.
This was found by code inspection and comparison with Bspec and
doesn't seem to fix any known issue.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
[danvet: Add note about impact.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we encounter frequent problems with dp aux channel
communications, we end up spamming the dmesg with the
exact similar trace and status.
Inject a new backtrace only if we have new information
to share as otherwise we flush out all other important
stuff.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-EDEADLK has special meaning in atomic, but get_fence may call
i915_find_fence_reg which can return -EDEADLK.
This has special meaning in the atomic world, so convert the error
to -EBUSY for this case.
Changes since v1:
- Add comment in the code.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The rest will be a noop anyway, since without modeset there will be
no updated dplls and no modeset state to update.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are no more users, byebye!
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that everything's atomic, checking encoder->base.crtc is enough.
This function doesn't have the locks to dereference crtc->state, but
stealing an encoder bound to any crtc is probably enough reason to warn.
Changes since v1:
- Commit message.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
connectors_active will be removed, so just calculate this instead.
Changes since v1:
- Look for the right pointer in intel_sanitize_encoder.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is now done completely atomically.
Keep connectors_active for now, but make it mirror crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of allocating pipe_config on the stack use the old
crtc_state, it's only going to freed from this point on.
All crtc' are now only checked once during modeset,
because false positives can happen with encoders after
dpms changes and to limit the amount of errors for 1 failure.
Changes since v1:
- crtc_state -> old_crtc_state
- state -> old_state
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Connectors are updated atomically now, so the only interaction
with the encoder is through base.crtc.
If it's NULL the encoder's not part of any crtc, and if it's
not NULL then active should be equal to crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is handled by the atomic core now, no need to check this for ourself.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Right now dpms callbacks can still fiddle with the connector state,
but it can only turn connectors off.
This is remediated by only checking crtc->state->active when the
connector is active, and ignore crtc->state->active when the
connector is off.
connectors_active is no longer checked, and will be removed later
in this series together with dpms.
Another check for !encoder->crtc is performed by check_encoder_state
too, so it can be removed.
Changes since v1:
- Add commit message.
- rename state to old_state.
- Move deletion of mst_port check to mst patch.
Changes since v2:
- Fix a null pointer dereference on MST now hw readout is fixed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
