Even though there's a WMI enum for fragmentation
threshold no known firmware actually implements
it. Moreover it is not possible to rely frame
fragmentation to mac80211 because firmware clears
the "more fragments" bit in frame control making
it impossible for remote devices to reassemble
frames.
Hence implement a dummy callback just to say
fragmentation isn't supported. This effectively
prevents mac80211 from doing frame fragmentation
in software.
This fixes Tx becoming broken after setting
fragmentation threshold.
Fixes: 1010ba4c5d ("ath10k: unregister and remove frag_threshold callback")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 1010ba4c5d ("ath10k: unregister and
remove frag_threshold callback") didn't remove all
instances of (futile) fragmentation threshold
configuration. No known firmware supports the
parameter so don't even bother setting it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For wake from S5, we need to:
- register a reboot handler
- set wakeup capability before requesting IRQ so wakeup count is
incremented
- mask all GPIO IRQs and clear any pending interrupts during driver
probe to since no driver will yet be registered to handle any IRQs
carried over from boot at that time, and it's possible that the
booted kernel does not request the same IRQ anyway.
This means that /sys/.../power/wakeup_count is valid at boot time, and
we can properly account for S5 wakeup stats. e.g.:
### After waking from S5 from a GPIO key
# cat /sys/bus/platform/drivers/brcmstb-gpio/f04172c0.gpio/power/wakeup
enabled
# cat /sys/bus/platform/drivers/brcmstb-gpio/f04172c0.gpio/power/wakeup_count
1
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Uses the gpiolib irqchip helpers. For this to work, the irq setup
function is called once per bank instead of once per device. Note
that all known uses of this block have a BCM7120 L2 interrupt
controller as a parent. Supports interrupts for all GPIOs.
In the IRQ handler, we check for raised IRQs for invalid GPIOs and
warn (ratelimited) if they're encountered.
Also, several drivers (e.g. gpio-keys) allow for GPIOs to be
configured as wakeup sources, and this GPIO controller supports that
through a separate interrupt path.
The de-facto standard DT property "wakeup-source" is checked, since
that indicates whether the GPIO controller hardware can wake. Uses
the IRQCHIP_MASK_ON_SUSPEND irq_chip flag because UPG GIO doesn't have
any of its own wakeup source configuration.
Aside regarding gpiolib irqchip helpers: It wasn't obvious (to me)
that you can have multiple chained irqchips and associated IRQ domains
for a single parent IRQ, and as long as the xlate function is written
correctly, a GPIO IRQ request end up checking the correct domain and
will get associated with the correct IRQ. What helps make this clear
is to read
drivers/gpio/gpiolib-of.c:
- of_gpiochip_find_and_xlate()
- of_get_named_gpiod_flags()
drivers/gpio/gpiolib.c:
- gpiochip_find()
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 926b663ce8
"gpiolib: allow GPIOs to be named" added the ability to
name GPIO lines by an array of names stored in the GPIO
chip. This was in 2009 and has been an ABI since. Let's
document it properly.
Cc: Daniel Silverstone <dsilvers@digital-scurf.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: Johan Hovold <johan@kernel.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=E1kF
-----END PGP SIGNATURE-----
Merge tag 'rpi-dt-for-armsoc-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/rpi/linux-rpi into next/dt
- New Firmware node and accompanying binding document
* tag 'rpi-dt-for-armsoc-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/rpi/linux-rpi:
dt/bindings: Add binding for the Raspberry Pi firmware driver
ARM: bcm2835: Add the firmware driver information to the RPi DT
Signed-off-by: Olof Johansson <olof@lixom.net>
All the EP93xx boards exclusively use modedb to look up video
modes from the command line. Root out the parametrization of
custom video modes from the platform data and board files
and simplify the driver.
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix i.MX6 PCIe interrupt routing which gets missed from stacked IRQ
domain conversion. The PCIe wakeup support is currently broken
because of this.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVyL2qAAoJEFBXWFqHsHzOGHgH/jgyCg6QVHgxgAoCjySZUbtT
OwYFKxR3697GGVyUMa0r47TQxL5PusCUzJrNJTg6AhhgatKsGfiB45NRZy5bt8k5
8M4tShc1n/fV7N2T1h1QbpXZiPhofhFtMq9Yq1lPDrQvOLOymWWZhGwBqbFy0bJT
4IzqUS7uTE/pvrbFf+iqlwxshSzbbMOOHPqAavyinAKQU5S93v7D4iKJ0q2EmTqh
hypAL1lZ0/BwBKWSeVVzJoVUFHZFmSzhlbE6ZzcY7S/4Dn2oTwiZQPb+eWj8kQHn
CALj6KFSnhQ4XKfcBFTH1Z/apSWs6SDWDOig2jzQ/X+JFo9ahnh4fp91NqLML+o=
=lUqF
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.2, 3rd round:
- Fix i.MX6 PCIe interrupt routing which gets missed from stacked IRQ
domain conversion. The PCIe wakeup support is currently broken
because of this.
* tag 'imx-fixes-4.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6: correct i.MX6 PCIe interrupt routing
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add DTS property "altr,modrst-offset" for reset driver to
use
- Add updated reset defines for the reset driver
- Add reset property for EMACs on Arria10
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dKt6
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_for_v4.3_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA DTS updates for v4.3, take 2
- Add DTS property "altr,modrst-offset" for reset driver to
use
- Add updated reset defines for the reset driver
- Add reset property for EMACs on Arria10
* tag 'socfpga_dts_for_v4.3_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: dts: Add resets for EMACs on Arria10
ARM: socfpga: dts: add "altr,modrst-offset" property
dt-bindings: Add reset manager offsets for Arria10
Signed-off-by: Olof Johansson <olof@lixom.net>
1. kfree() of read-only memory (name of power domain returned
by kstrdup_const()),
2. Doubled of_node_put() leading to invalid ref count for OF node.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qAfT
-----END PGP SIGNATURE-----
Merge tag 'samsung-mach-fixes-4.2' of https://github.com/krzk/linux into fixes
Two fixes for bugs in Exynos power domain error exit path:
1. kfree() of read-only memory (name of power domain returned
by kstrdup_const()),
2. Doubled of_node_put() leading to invalid ref count for OF node.
* tag 'samsung-mach-fixes-4.2' of https://github.com/krzk/linux:
ARM: EXYNOS: fix double of_node_put() on error path
ARM: EXYNOS: Fix potentian kfree() of ro memory
Signed-off-by: Olof Johansson <olof@lixom.net>
Cortex-A9 SoCs and actually enabling usb on the rk3066-marsboard,
Two more veyron-devices - namely Speedy and Minnie and a fix for
the tsadc.
One slightly more interesting fix is the blocking of the last
16MB of memory on 4GB rk3288 devices. The rk3288 cannot use this
area for dma operations, so things like the mmc or usb controllers
regularly fail when trying to read data. This solution mimicks the
solution from the ChromeOS kernel, who also do not seem to have
found a better solution yet. Here it only moves to the devicetree.
As this issue is also present on the arm64 rk3368, any future
better solution to this problem would need to describe this in
the devicetree as well and could then remove this block.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJVxnMhAAoJEPOmecmc0R2BGXAH/03qzTWzHaLJH73zNj2+r7cm
GwlwxntSDb4e6lq5hKT1+biqBrin+IrzA1sCcyeiFlg3wOWP5AuuEyiKgVKHZ//c
9dKAVsmtX5TMliFPA+U6SvEyURPk5RSU30cTgYEEBVhwWhDduDnJOBmOpLhHyQUC
36FMlfNBpNQQHYQUNziXEgnWZNtvdiYnmt4FPkdQWT08kZKJvyky+gbqOkya4RzH
Pi70IzQyh3F0UiQR4f34q+C0+KStF9LdZSeYgnnY++Sg+5Wz9FAWcdoo2qwi2C8t
qVPEF2B1vW87+9z3WtGRk2CE48uy6QS7WQL3l/wHp6RxMCPXu9QjOAHOl2rBHSs=
=2Rte
-----END PGP SIGNATURE-----
Merge tag 'v4.3-rockchip32-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Some more devicetree changes, including usbphy support for the
Cortex-A9 SoCs and actually enabling usb on the rk3066-marsboard,
Two more veyron-devices - namely Speedy and Minnie and a fix for
the tsadc.
One slightly more interesting fix is the blocking of the last
16MB of memory on 4GB rk3288 devices. The rk3288 cannot use this
area for dma operations, so things like the mmc or usb controllers
regularly fail when trying to read data. This solution mimicks the
solution from the ChromeOS kernel, who also do not seem to have
found a better solution yet. Here it only moves to the devicetree.
As this issue is also present on the arm64 rk3368, any future
better solution to this problem would need to describe this in
the devicetree as well and could then remove this block.
* tag 'v4.3-rockchip32-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add veyron-minnie board
ARM: dts: rockchip: reserve unusable memory region on rk3288
ARM: dts: rockchip: enable usb controller on marsboard
ARM: dts: rockchip: add usb phys to Cortex-A9 socs
ARM: dts: rockchip: set correct dwc2 params for cortex-a9 socs
ARM: dts: rockchip: Add veyron-speedy board
ARM: dts: rockchip: Use correct dts properties for tsadc node on veyron
Signed-off-by: Olof Johansson <olof@lixom.net>
reason resuming from suspend worked sucessfully on the rk3288-evb
but not on other boards, like veyron-devices. Two problems seem
to have existed. For one the stabilization delays for pmic and
oscillator may have been to short and secondly the shallow
suspend seems to need GPIO wakups enabled. Normally this should
be covered by the more generic ARMINT wakeups already and
the reason for this is still investigated at Rockchip, but
meanwhile this makes boards actually resume.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJVxnDGAAoJEPOmecmc0R2BeAAH/0b/X33+HKzp+uSnKfxpRtoW
PiSLKVlKEsbrJzQhVntBfE7PBg/vQkGtcKU6V89QC2kXbOqWRG2OTjMBXD9wPcA2
XDBw3VeFX5PSV2f2054FfEHVz+tSY4ZTchgvU2I19kTF5HpJ5E5rTO/9W4a1kqoj
w6wnGvXwpJ7LO1RKR3JRwWbUAUsYsn7rynhB5Ndmg9LUixs46EysqIyFbsxsWNGg
8tSnzC8b8F2QEvEq/+mYLpvno65I1dMXy5Bdh8VR9nWkJcGVcDdDfojU/6WXYHCX
jk1LT5dNtf1y+3owDQUcqlgNYGyeQrawnWlFD+R6IgZOdb1rSY5/qTF8etwSMa4=
=SFTV
-----END PGP SIGNATURE-----
Merge tag 'v4.3-rockchip32-soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/soc
Improve reliability of resume on rk3288 boards. For whatever
reason resuming from suspend worked sucessfully on the rk3288-evb
but not on other boards, like veyron-devices. Two problems seem
to have existed. For one the stabilization delays for pmic and
oscillator may have been to short and secondly the shallow
suspend seems to need GPIO wakups enabled. Normally this should
be covered by the more generic ARMINT wakeups already and
the reason for this is still investigated at Rockchip, but
meanwhile this makes boards actually resume.
* tag 'v4.3-rockchip32-soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: rockchip: enable PMU_GPIOINT_WAKEUP_EN when entering shallow suspend
ARM: rockchip: set correct stabilization thresholds in suspend
ARM: rockchip: rename osc_switch_to_32k variable
Signed-off-by: Olof Johansson <olof@lixom.net>
This is unnecessary since commit 02b4e2756e ("ARM: v7 setup
function should invalidate L1 cache").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
CONFIG_ARM_AT91_ETHER doesn't exist anymore, both drivers have been merged
in the macb driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
SoC part of the Dove PMU series
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlXE0fgACgkQCwYYjhRyO9XUKwCeIOTx172942DUMzGwO3feDGZn
zCgAn2yxrZaFqUo/EfVqgieeTGBmY6gh
=gfKo
-----END PGP SIGNATURE-----
Merge tag 'mvebu-soc-4.3-2' of git://git.infradead.org/linux-mvebu into next/drivers
mvebu soc changes for v4.3 (part #2)
SoC part of the Dove PMU series
* tag 'mvebu-soc-4.3-2' of git://git.infradead.org/linux-mvebu:
ARM: dove: create a proper PMU driver for power domains, PMU IRQs and resets
Signed-off-by: Olof Johansson <olof@lixom.net>
- device tree part of the Dove PMU series
- converting a new orion5x based platform to dt: Linkstation Mini
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlXE1doACgkQCwYYjhRyO9VyywCghy4yCyXWjfJ+rIE9uZ0JZwg7
TYcAmgKPY3lgL1cXdRTTo82iXRwRM3Ht
=ndrR
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.3-3' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt changes for v4.3 (part #3)
- device tree part of the Dove PMU series
- converting a new orion5x based platform to dt: Linkstation Mini
* tag 'mvebu-dt-4.3-3' of git://git.infradead.org/linux-mvebu:
ARM: dts: Convert Linkstation Mini to Device Tree
ARM: dt: dove: add GPU power domain description
ARM: dt: dove: add video decoder power domain description
ARM: dt: dove: wire up RTC interrupt
ARM: dt: Add PMU node, making PMU child devices childs of this node
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add the slow clock to the nodes that will use it
- Add hlcd to the at91sam9x5 and at91sam9n12
- Add touchscreen and touch button support to the at91sam9x5ek
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=u5hT
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
Second batch of DT changes for 4.3:
- Add the slow clock to the nodes that will use it
- Add hlcd to the at91sam9x5 and at91sam9n12
- Add touchscreen and touch button support to the at91sam9x5ek
* tag 'at91-ab-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (22 commits)
ARM: at91/dt: sama5d2: use slow clock where necessary
ARM: at91/dt: at91sam9x5dm: add QT1070 touch button controller
ARM: at91/dt: at91sam9x5dm: add support for the touschscreen
ARM: at91/dt: add drm support for at91sam9n12ek
ARM: at91/dt: enable lcd support for at91sam9x5 SoCs
ARM: at91/dt: add at91sam9x5-ek Display Module dtsi
ARM: at91/dt: include lcd dtsi in at91sam9x5 dtsis
ARM: at91/dt: define hlcdc node in at91sam9x5_lcd.dtsi
ARM: at91/dt: sama5d4: use slow clock where necessary
ARM: at91/dt: sama5d3: use slow clock where necessary
ARM: at91/dt: at91sam9x5: use slow clock where necessary
ARM: at91/dt: at91sam9rl: use slow clock where necessary
ARM: at91/dt: at91sam9n12: use slow clock where necessary
ARM: at91/dt: at91sam9g45: use slow clock where necessary
ARM: at91/dt: at91sam9263: use slow clock where necessary
ARM: at91/dt: at91sam9261: use slow clock where necessary
ARM: at91/dt: at91sam9260: use slow clock where necessary
ARM: at91/dt: at91rm9200: use slow clock where necessary
Documentation: dt: rtc: at91rm9200: add clocks property
Documentation: watchdog: at91sam9_wdt: add clocks property
...
Signed-off-by: Olof Johansson <olof@lixom.net>
1. error handling for irq routes
2. Gracefully handle STP time changes
s390 supports a protocol for syncing different systems via the stp
protocol that will steer the TOD clocks to keep all participating
clocks below the round trip time between the system. In case of
specific out of sync event Linux can opt-in to accept sync checks.
This will result in non-monotonic jumps of the TOD clock, which
Linux will correct via time offsets to keep the wall clock time
monotonic. Now: KVM guests also base their time on the host TOD,
so we need to fixup the offset for them as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=2kz9
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-20150812' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: fix and feature for kvm/next (4.3)
1. error handling for irq routes
2. Gracefully handle STP time changes
s390 supports a protocol for syncing different systems via the stp
protocol that will steer the TOD clocks to keep all participating
clocks below the round trip time between the system. In case of
specific out of sync event Linux can opt-in to accept sync checks.
This will result in non-monotonic jumps of the TOD clock, which
Linux will correct via time offsets to keep the wall clock time
monotonic. Now: KVM guests also base their time on the host TOD,
so we need to fixup the offset for them as well.
In the original driver it is missed to setup a free running driver.
This timer is needed for the scheduler.
So setup it.
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Use timer1 as clockevent timer.
The old driver uses timer2, which has some issues to setup
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add missing register defintions for the gemini clocksource
Also do some #define' cleanup to make the code more readable.
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The outside if statement checks that IEEE80211_TX_INTFL_MLME_CONN_TX is
set so this condition is always true. Checking twice upsets the static
checkers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The iwlwifi driver was the only driver that used this, but as
it turns out it never needed it, so we can remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to firmware engineers, the firmware has never required
these fields and the values have always been calculated, they were
just leftovers from a previous implementation.
Therefore remove the unnecessary calculation.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Migrate EP93xx driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch is based on the upstream commit 5ac1c4bcf0 and amended
for v4.2 to make sure it works as intended.
Repeated calls to begin_crtc_commit can cause warnings like this:
[ 169.127746] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:616
[ 169.127835] in_atomic(): 0, irqs_disabled(): 1, pid: 1947, name: kms_flip
[ 169.127840] 3 locks held by kms_flip/1947:
[ 169.127843] #0: (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffff814774bc>] __drm_modeset_lock_all+0x9c/0x130
[ 169.127860] #1: (crtc_ww_class_acquire){+.+.+.}, at: [<ffffffff814774cd>] __drm_modeset_lock_all+0xad/0x130
[ 169.127870] #2: (crtc_ww_class_mutex){+.+.+.}, at: [<ffffffff81477178>] drm_modeset_lock+0x38/0x110
[ 169.127879] irq event stamp: 665690
[ 169.127882] hardirqs last enabled at (665689): [<ffffffff817ffdb5>] _raw_spin_unlock_irqrestore+0x55/0x70
[ 169.127889] hardirqs last disabled at (665690): [<ffffffffc0197a23>] intel_pipe_update_start+0x113/0x5c0 [i915]
[ 169.127936] softirqs last enabled at (665470): [<ffffffff8108a766>] __do_softirq+0x236/0x650
[ 169.127942] softirqs last disabled at (665465): [<ffffffff8108ae75>] irq_exit+0xc5/0xd0
[ 169.127951] CPU: 1 PID: 1947 Comm: kms_flip Not tainted 4.1.0-rc4-patser+ #4039
[ 169.127954] Hardware name: LENOVO 2349AV8/2349AV8, BIOS G1ETA5WW (2.65 ) 04/15/2014
[ 169.127957] ffff8800c49036f0 ffff8800cde5fa28 ffffffff817f6907 0000000080000001
[ 169.127964] 0000000000000000 ffff8800cde5fa58 ffffffff810aebed 0000000000000046
[ 169.127970] ffffffff81c5d518 0000000000000268 0000000000000000 ffff8800cde5fa88
[ 169.127981] Call Trace:
[ 169.127992] [<ffffffff817f6907>] dump_stack+0x4f/0x7b
[ 169.128001] [<ffffffff810aebed>] ___might_sleep+0x16d/0x270
[ 169.128008] [<ffffffff810aed38>] __might_sleep+0x48/0x90
[ 169.128017] [<ffffffff817fc359>] mutex_lock_nested+0x29/0x410
[ 169.128073] [<ffffffffc01635f0>] ? vgpu_write64+0x220/0x220 [i915]
[ 169.128138] [<ffffffffc017fddf>] ? ironlake_update_primary_plane+0x2ff/0x410 [i915]
[ 169.128198] [<ffffffffc0190e75>] intel_frontbuffer_flush+0x25/0x70 [i915]
[ 169.128253] [<ffffffffc01831ac>] intel_finish_crtc_commit+0x4c/0x180 [i915]
[ 169.128279] [<ffffffffc00784ac>] drm_atomic_helper_commit_planes+0x12c/0x240 [drm_kms_helper]
[ 169.128338] [<ffffffffc0184264>] __intel_set_mode+0x684/0x830 [i915]
[ 169.128378] [<ffffffffc018a84a>] intel_crtc_set_config+0x49a/0x620 [i915]
[ 169.128385] [<ffffffff817fdd39>] ? mutex_unlock+0x9/0x10
[ 169.128391] [<ffffffff81467b69>] drm_mode_set_config_internal+0x69/0x120
[ 169.128398] [<ffffffff8119b547>] ? might_fault+0x57/0xb0
[ 169.128403] [<ffffffff8146bf93>] drm_mode_setcrtc+0x253/0x620
[ 169.128409] [<ffffffff8145c600>] drm_ioctl+0x1a0/0x6a0
[ 169.128415] [<ffffffff810b3b41>] ? get_parent_ip+0x11/0x50
[ 169.128424] [<ffffffff811e9ab8>] do_vfs_ioctl+0x2f8/0x530
[ 169.128429] [<ffffffff810d0fcd>] ? trace_hardirqs_on+0xd/0x10
[ 169.128435] [<ffffffff812e7676>] ? selinux_file_ioctl+0x56/0x100
[ 169.128439] [<ffffffff811e9d71>] SyS_ioctl+0x81/0xa0
[ 169.128445] [<ffffffff81800697>] system_call_fastpath+0x12/0x6f
Solve it by using the newly introduced drm_atomic_helper_commit_planes_on_crtc.
The problem here was that the drm_atomic_helper_commit_planes() helper
we were using was basically designed to do
begin_crtc_commit(crtc #1)
begin_crtc_commit(crtc #2)
...
commit all planes
finish_crtc_commit(crtc #1)
finish_crtc_commit(crtc #2)
The problem here is that since our hardware relies on vblank evasion,
our CRTC 'begin' function waits until we're out of the danger zone in
which register writes might wind up straddling the vblank, then disables
interrupts; our 'finish' function re-enables interrupts after the
registers have been written. The expectation is that the operations between
'begin' and 'end' must be performed without sleeping (since interrupts
are disabled) and should happen as quickly as possible. By clumping all
of the 'begin' calls together, we introducing a couple problems:
* Subsequent 'begin' invocations might sleep (which is illegal)
* The first 'begin' ensured that we were far enough from the vblank that
we could write our registers safely and ensure they all fell within
the same frame. Adding extra delay waiting for subsequent CRTC's
wasn't accounted for and could put us back into the 'danger zone' for
CRTC #1.
This commit solves the problem by using a new helper that allows an
order of operations like:
for each crtc {
begin_crtc_commit(crtc) // sleep (maybe), then disable interrupts
commit planes for this specific CRTC
end_crtc_commit(crtc) // reenable interrupts
}
so that sleeps will only be performed while interrupts are enabled and
we can be sure that registers for a CRTC will be written immediately
once we know we're in the safe zone.
The crtc->config->base.crtc update may seem unrelated, but the helper
will use it to obtain the crtc for the state. Without the update it
will dereference NULL and crash.
Changes since v1:
- Use Matt Roper's commit message.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=90398
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This should be much cleaner, with the same effects.
(cherry picked for v4.2 from commit fb9d6cf8c2)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=90398
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In
commit d328c9d78d
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Apr 10 16:22:37 2015 +0200
drm/i915: Select starting pipe bpp irrespective or the primary plane
we started to select the pipe bpp from sink capabilities and not from
the primary framebuffer - that one might change (and we don't want to
incur a modeset) and sprites might contain higher bpp content too.
We also selected dithering on a 8 bpc screen displaying a 24bpp rgb
primary, because pipe_bpp is 24 for such a typical 8 bpc sink, but since
the commit mentioned above, base_bpp is always the absolute maximum
supported by the hardware, e.g., 36 bpp on my Ironlake chip. Iow. the
only way to not get dithering would have been to connect a deep color 12
bpc display, so pipe_bpp == 36 == base_bpp.
Hence only enable dithering on 6bpc screens where we difinitely and
always want it.
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Reported-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-and-tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
AM437x devices sport SCU, TWD and Global timers,
let's add them to DTS so they have a chance to
probe and be used by Linux.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is an x86-specific module and would benefit from being
closer to the arch code. Move it there. Update copyright while
at it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1439396985-12812-14-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Will be used by an injector module in a following patch.
Additionally, add a missing module export reported by 0-DAY
kernel test.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1439396985-12812-13-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The "rcu_" prefix misleads for it being a proper RCU interface
which is not. It basically checks whether we're preemptible or
holding the chrdev_read mutex.
Rename it accordingly.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1439396985-12812-12-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Text taken a previous patch from "Gong Chen" <gong.chen@linux.intel.com>.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Gong Chen <gong.chen@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1439396985-12812-11-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Zhang Liguang reported the following issue:
1) System detects a CMCI storm on the current CPU.
2) Kernel disables the CMCI interrupt on banks owned by the
current CPU and switches to poll mode
3) After the CMCI storm subsides, kernel switches back to
interrupt mode
4) We expect the system to reenable the CMCI interrupt on banks
owned by the current CPU
mce_intel_adjust_timer
|-> cmci_reenable
|-> cmci_discover # owned banks are ignored here
static void cmci_discover(int banks)
...
for (i = 0; i < banks; i++) {
...
if (test_bit(i, owned)) # ownd banks is ignore here
continue;
So convert cmci_storm_disable_banks() to
cmci_toggle_interrupt_mode() which controls whether to enable or
disable CMCI interrupts with its argument.
NB: We cannot clear the owned bit because the banks won't be
polled, otherwise. See:
27f6c573e0 ("x86, CMCI: Add proper detection of end of CMCI storms")
for more info.
Reported-by: Zhang Liguang <zhangliguang@huawei.com>
Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: huawei.libin@huawei.com
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: rui.xiang@huawei.com
Link: http://lkml.kernel.org/r/1439396985-12812-10-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
kexec could boot a kernel that could be legacy with no knowledge
of LMCE. Hence we should make sure we clear LMCE optin before
kexec reboot.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1439396985-12812-9-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This used to flush out MCEs logged during early boot and which
were in the MCA registers from a previous system run. No need
for that now, since we've moved to a genpool.
Suggested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1439396985-12812-7-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Printing in MCE context is a no-no, currently, as printk() is
not NMI-safe. If some of the notifiers on the MCE chain call do
so, we may deadlock. In order to avoid that, delay printk() to
process context where it is safe.
Reported-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
[ Fold in subsequent patch from Boris for early boot logging. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
[ Kick irq_work in mce_log() directly. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1439396985-12812-6-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Use unified genpool to save Action Optional error events and put
Action Optional error handling in the same notification chain as
MCE error decoding.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
[ Fold in subsequent patch from Boris for early boot logging. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
[ Correct a lot. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1439396985-12812-5-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
An MCE is a rare event. Therefore, there's no need to have
per-CPU instances of both normal and IRQ workqueues. Make them
both global.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
[ Fold in subsequent patch from Rui/Boris/Tony for early boot logging. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
[ Massage commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1439396985-12812-4-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
printk() is not safe to use in MCE context. Add a lockless
memory allocator pool to save error records in MCE context.
Those records will be issued later, in a printk-safe context.
The idea is inspired by the APEI/GHES driver.
We're very conservative and allocate only two pages for it but
since we're going to use those pages throughout the system's
lifetime, we allocate them statically to avoid early boot time
allocation woes.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
[ Rewrite. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1439396985-12812-3-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
... to save the error severity of the MCE and whether the
reported address of the error is usable.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1439396985-12812-2-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also set IRQ_NOPROBE and this has been maintained although it is not
clear that is really needed. There appears to be a great deal of blind
copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Roger Quadros <rogerq@ti.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
User visible:
- Allow selecting the type of callchains per event, including disabling
callchains in all but one entry in an event list, to save space, and also
to ask for the callchains collected in one event to be used in other
events (Kan Liang)
- Beautify more syscall arguments in 'perf trace': (Arnaldo Carvalho de Melo)
- A bunch more translate file/pathnames from pointers to strings
- Convert numbers to strings for the 'keyctl' syscall 'option' arg.
- Add missing 'clockid' entries
- Fix 'perf probe -L sys_*' as it was not showing all the source code for
syscall functions in the kernel (Masami Hiramatsu)
- Make ESC unzoom as well in the hists browser, i.e. in 'report' and 'top',
as we're considering repurposing the right and left arrow keys to use in
horizontal scrolling, i.e. leave just ESC to be used for what <- works
now, and ENTER for what -> does (they are already aliases for ages)
(Arnaldo Carvalho de Melo)
Infrastructure fixes:
- Check for SRCLINE_UNKNOWN case in "srcfile" processing (Andi Kleen)
- Wrap the slsmg_{printf,write_nstring} slang functions behing ui_browser, so
that we can make the ui_browser based browsers (annotate, menus, hists, etc) UI
library agnostic and usable with multiple backends (slang now, GTK+ and others
in the future, maybe) (Arnaldo Carvalho de Melo)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=phTT
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
User visible changes:
- Allow selecting the type of callchains per event, including disabling
callchains in all but one entry in an event list, to save space, and also
to ask for the callchains collected in one event to be used in other
events. (Kan Liang)
- Beautify more syscall arguments in 'perf trace': (Arnaldo Carvalho de Melo)
- A bunch more translate file/pathnames from pointers to strings.
- Convert numbers to strings for the 'keyctl' syscall 'option' arg.
- Add missing 'clockid' entries.
- Fix 'perf probe -L sys_*' as it was not showing all the source code for
syscall functions in the kernel. (Masami Hiramatsu)
- Make ESC unzoom as well in the hists browser, i.e. in 'report' and 'top',
as we're considering repurposing the right and left arrow keys to use in
horizontal scrolling, i.e. leave just ESC to be used for what <- works
now, and ENTER for what -> does (they are already aliases for ages).
(Arnaldo Carvalho de Melo)
Infrastructure fixes:
- Check for SRCLINE_UNKNOWN case in "srcfile" processing (Andi Kleen)
- Wrap the slsmg_{printf,write_nstring} slang functions behind ui_browser, so
that we can make the ui_browser based browsers (annotate, menus, hists, etc) UI
library agnostic and usable with multiple backends (slang now, GTK+ and others
in the future, maybe) (Arnaldo Carvalho de Melo)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Variable 'ret' is only used for returning the value 0.
We can make it simpler and just return 0 instead.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/returnvar.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In the error paths we should free the resources that were
previously acquired, so fix it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
