Patch enables SuperSpeed for NCM gadget.
Tested with USB3380 and measured TCP throughput with two Intel PCs:
udc to host: 920 Mbit/s
host to udc: 550 Mbit/s
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
alloc_ordered_workqueue replaces the deprecated
create_singlethread_workqueue.
There are multiple work items on the work queue, which require
ordering. Hence, an ordered workqueue has been used.
The workqueue "wq_otg" is not being used on a memory reclaim path.
Hence, WQ_MEM_RECLAIM has not been set.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The assignment ret = ret is redundant and can be removed.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabling USB gadget functions configured through configfs is something
that can happen in normal use cases. Keep the existing log for this type
of event, but only as information, not as an error.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As the last known user, ie. pxa27x_udc relying on calls to
usb_gadget_xxx() was amended to use the phy notifier, remove a bit the
USB stack adherence.
Actually the driver still uses the gadget API for structures definition,
but the implementation of USB gadget specific function usb_gadget_*() is
not necessary anymore.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the gpio based case, the status of the phy is known at start by
reading the VBus gpio.
Actually, this is a fix, as this initial state, when not set up,
prevents a gadget to answer to the enumeration phase, as there is no
notification in this case (the VBus is already high when kernel boots)
so no interrupt is triggered, and the flow is :
- gadget initializes
- gadget gets its phy-generic with a xxx_get_phy_xxx() call type
- gadget does a "set_peripheral()" call type
=> here if the otg->state is correctly filled, the proper vbus
handling will be called, and the gadget will be aware it should
answer enumeration and go forth
Without this fix, the USB cable must be removed and replugged for any
gadget relying on phy-generic and its gpio vbus handling to work.
The problem was seen on a pxa27x architecture based board on a
devicetree build.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the legacy behavior, and USB phy, upon detection a VBus signal, was
calling usb_gadget_vbus_(dis)connect().
This model doesn't work if the phy is generic and doesn't have an
adherence to the gadget API.
Instead of relying on the phy to call the gadget API, hook up the phy
notifier to report the VBus event, and upon it call the usb gadget API
ourselves.
This brings a new ordering problem, as before even if the usb_get_phy()
was failing because the UDC was probed before the phy, the phy would
call the gadget anyway, making the VBus connection event forwarded to
the gadget. Now we rely on the notifier, we have to ensure the
xxx_get_phy() does indeed work.
In order to cope with this, it is assumed that :
- for legacy platform_data machine, as the ordering cannot be ensured,
the phy must call usb_gadget_vbus_(dis)connect, such as
phy-gpio-vbus-usb.c
- for new devicetree platforms, we'll rely on the probe deferral, and
the phy can be gadget API agnostic.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Upon transfer completion after a full ring, let's
add more TRBs to our ring in order to complete our
request successfully.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the ring is full and we are processing a big
sglist, then let's interrupt so we can, later, add
more TRBs to the ring.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
These two fields will be used in a follow-up patch
to track how many entries of request's sglist we
have already processed. The reason is that if a
gadget driver sends an sglist with more entries then
we can fit in the ring, we will have to continue
processing remaining afterwards.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We know that we have to iterate over the list of
started requests. Instead of looping forever, we can
rely on list_for_each_entry(). Likewise, instead of
a do {} while loop over all, maybe available,
scatterlist entries, we can detect if $this request
uses scatterlist and rely on for_each_sg().
This makes the code easier to follow while making
sure that we will *always* break out of the loop.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Many of the comments in that function are really
outdated and don't match what the driver is
doing. Moreover, recent patches combined programming
model for all non-control endpoints, this gives us
an opportunity to get rid of our special cases in
__dwc3_gadget_ep_queue().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We always need to decrement our index by at least
one. Simplify the implementation by using a
temporary local variable and making sure that we
will always decrement one extra if tmp == 0.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of waiting until giveback before
incrementing the dequeue pointer, we can increment
it from dwc3_cleanup_done_reqs(), that way we avoid
an extra loop over all TRBs during giveback.
While at that, also avoid using req->first_trb_index
as that's completely unnecessary. A follow-up patch
will clean up further uses of that and remove the
field altogether.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The only endpoint which actually requires LST bit
and XferComplete is ep0/1. Let's save some time by
completely removing LST bit support and
XferComplete.
This simplifies and consolidates endpoint handling
for all other 3 transfer types while also avoiding
extra interrupts.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is an entirely new driver instead of yet another set of patches
to sb_edac.c because:
1) Mapping from PCI devices to socket/memory controller is significantly
different. Skylake scatters devices on a socket across a number of
PCI buses.
2) There is an extra level of interleaving via the "mcroute" register
that would be a little messy to squeeze into the old driver.
3) Validation is getting too expensive. Changes to sb_edac need to
be checked against Sandy Bridge, Ivy Bridge, Haswell, Broadwell and
Knights Landing.
Acked-by: Aristeu Rozanski <aris@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull i2c fixes from Wolfram Sang:
"I2C has some pretty standard driver bugfixes and one minor cleanup"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: meson: Use complete() instead of complete_all()
i2c: brcmstb: Use complete() instead of complete_all()
i2c: bcm-kona: Use complete() instead of complete_all()
i2c: bcm-iproc: Use complete() instead of complete_all()
i2c: at91: fix support of the "alternative command" feature
i2c: ocores: add missed clk_disable_unprepare() on failure paths
i2c: cros-ec-tunnel: Fix usage of cros_ec_cmd_xfer()
i2c: mux: demux-pinctrl: properly roll back when adding adapter fails
preemption before using this_cpu_ptr()
- a slight increase in DM crypt's mempool reserves to make swap ontop of
DM crypt more performant
- a few DM raid fixes to issues found while testing changes that were
merged in v4.8-rc1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXty5yAAoJEMUj8QotnQNaD98H/RAQd3uwboN/R6C8kwDscw5R
LvSjGJRV6y6GvAg+ItIWx2pzFnQp5ceP+D3irMSCYGhCM8+kkSymHi9Hkx0q9wcF
pld6hImye+b/59x5GuAKKNaCMjH4teQtzLBWuoG5E6/3sjXPgTBuSj8183yDrhgX
RlCu/4XmBcR0/9Ypc3YludSuovAMNjvgCkJc9kNURTDYW+GSshmhPfzE5cNeEo5A
++KFcLQiRKOc1GbgTtyYbbBiv0m61u7sr7mM97LtnxogZ86bsJPI20RmeXygvrd7
QGz2joxjPeI+WwQ1Y8OXG6ZT7LxT4ZWkvmd1gGXWBZur0cgM+bZaHI+Kc3Q89hk=
=RtQ+
-----END PGP SIGNATURE-----
Merge tag 'dm-4.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a stable fix for DM round robin multipath path selector to disable
preemption before using this_cpu_ptr()
- a slight increase in DM crypt's mempool reserves to make swap ontop
of DM crypt more performant
- a few DM raid fixes to issues found while testing changes that were
merged in v4.8-rc1
* tag 'dm-4.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm raid: support raid0 with missing metadata devices
dm raid: enhance attempt_restore_of_faulty_devices() to support more devices
dm raid: fix restoring of failed devices regression
dm raid: fix frozen recovery regression
dm crypt: increase mempool reserve to better support swapping
dm round robin: do not use this_cpu_ptr() without having preemption disabled
Six fairly small fixes. The ipr, mpt3sas and ses ones all trigger
oopses. The megaraid one fixes an attach failure on io mapped only
cards, the fcoe one is an obvious problem in the error path and the
aacraid one is a theoretical security issue (ability to trick the
kernel into a buffer overrun).
Signed-off-by: James E. J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=rA0D
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fairly small fixes. The ipr, mpt3sas and ses ones all trigger
oopses. The megaraid one fixes an attach failure on io mapped only
cards, the fcoe one is an obvious problem in the error path and the
aacraid one is a theoretical security issue (ability to trick the
kernel into a buffer overrun)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
ses: Fix racy cleanup of /sys in remove_dev()
mpt3sas: Fix resume on WarpDrive flash cards
ipr: Fix sync scsi scan
megaraid_sas: Fix probing cards without io port
aacraid: Check size values after double-fetch from user
fcoe: Use kfree_skb() instead of kfree()
Here are a number of USB fixes for reported issues for your tree.
The normal amount of gadget fixes, xhci fixes, new device ids, and a few
other minor things. All of them have been in linux-next for a while,
the full details are in the shortlog below.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iFYEABECABYFAle3IusPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspeXcAn1DY
3SBhV+JJ9vhpOwjEyh6GaUqGAKCzL27krQ1GiOmGSwA/DcMHAtp6Lg==
=sZB8
-----END PGP SIGNATURE-----
Merge tag 'usb-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for reported issues for your tree.
The normal amount of gadget fixes, xhci fixes, new device ids, and a
few other minor things. All of them have been in linux-next for a
while, the full details are in the shortlog below"
* tag 'usb-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (43 commits)
xhci: don't dereference a xhci member after removing xhci
usb: xhci: Fix panic if disconnect
xhci: really enqueue zero length TRBs.
xhci: always handle "Command Ring Stopped" events
cdc-acm: fix wrong pipe type on rx interrupt xfers
usb: misc: usbtest: add fix for driver hang
usb: dwc3: gadget: stop processing on HWO set
usb: dwc3: don't set last bit for ISOC endpoints
usb: gadget: rndis: free response queue during REMOTE_NDIS_RESET_MSG
usb: udc: core: fix error handling
usb: gadget: fsl_qe_udc: off by one in setup_received_handle()
usb/gadget: fix gadgetfs aio support.
usb: gadget: composite: Fix return value in case of error
usb: gadget: uvc: Fix return value in case of error
usb: gadget: fix check in sync read from ep in gadgetfs
usb: misc: usbtest: usbtest_do_ioctl may return positive integer
usb: dwc3: fix missing platform_set_drvdata() in dwc3_of_simple_probe()
usb: phy: omap-otg: Fix missing platform_set_drvdata() in omap_otg_probe()
usb: gadget: configfs: add mutex lock before unregister gadget
usb: gadget: u_ether: fix dereference after null check coverify warning
...
Fix a bug in it87 driver and URLs in ftsteutates driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KJoI
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix a bug in it87 driver and URLs in ftsteutates driver"
* tag 'hwmon-for-linus-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ftsteutates) Correct ftp urls in driver documentation
hwmon: (it87) Features mask must be 32 bit wide
Pull more drm fixes from Dave Airlie:
"Daniel pointed out I'd missed some i915 fixes, and I also found a
single etnaviv fix I missed.
So here they are"
* tag 'drm-fixes-for-4.8-rc3-2' of git://people.freedesktop.org/~airlied/linux:
drm/etnaviv: take GPU lock later in the submit process
drm/i915: Fix modeset handling during gpu reset, v5.
drm/i915: fix aliasing_ppgtt leak
drm/i915: fix WaInsertDummyPushConstPs
drm/i915: Fix iboost setting for SKL Y/U DP DDI buffer translation entry 2
drm/i915/gen9: Give one extra block per line for SKL plane WM calculations
drm/i915: Acquire audio powerwell for HD-Audio registers
drm/i915: Add missing rpm wakelock to GGTT pread
drm/i915/fbc: FBC causes display flicker when VT-d is enabled on Skylake
drm/i915: Clean up the extra RPM ref on CHV with i915.enable_rc6=0
drm/i915: Program iboost settings for HDMI/DVI on SKL
drm/i915: Fix iboost setting for DDI with 4 lanes on SKL
drm/i915: Handle ENOSPC after failing to insert a mappable node
drm/i915: Flush GT idle status upon reset
- Couple of DT node ref counting fixes
- Fix __unflatten_device_tree for PPC PCI hotplug case
- Rework marking irq controllers as OF_POPULATED in cases where real
driver is used.
- Disable of_platform_default_populate_init on PPC. The change in
initcall order causes problems which need to be sorted out later.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=s/uZ
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- a couple of DT node ref counting fixes
- fix __unflatten_device_tree for PPC PCI hotplug case
- rework marking irq controllers as OF_POPULATED in cases where real
driver is used.
- disable of_platform_default_populate_init on PPC. The change in
initcall order causes problems which need to be sorted out later.
* tag 'devicetree-fixes-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: fix reference counting in of_graph_get_endpoint_by_regs
of/platform: disable the of_platform_default_populate_init() for all the ppc boards
ARM: imx6: mark GPC node as not populated after irq init to probe pm domain driver
of/irq: Mark interrupt controllers as populated before initialisation
drivers/of: Validate device node in __unflatten_device_tree()
of: Delete an unnecessary check before the function call "of_node_put"
Collection of i915 fixes.
* tag 'drm-intel-fixes-2016-08-15' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix modeset handling during gpu reset, v5.
drm/i915: fix aliasing_ppgtt leak
drm/i915: fix WaInsertDummyPushConstPs
drm/i915: Fix iboost setting for SKL Y/U DP DDI buffer translation entry 2
drm/i915/gen9: Give one extra block per line for SKL plane WM calculations
drm/i915: Acquire audio powerwell for HD-Audio registers
drm/i915: Add missing rpm wakelock to GGTT pread
drm/i915/fbc: FBC causes display flicker when VT-d is enabled on Skylake
drm/i915: Clean up the extra RPM ref on CHV with i915.enable_rc6=0
drm/i915: Program iboost settings for HDMI/DVI on SKL
drm/i915: Fix iboost setting for DDI with 4 lanes on SKL
drm/i915: Handle ENOSPC after failing to insert a mappable node
drm/i915: Flush GT idle status upon reset
Pull drm fixes from Dave Airlie:
"Pretty quiet so far:
- a few amdgpu/radeon fixup for pcie pm changes
- a couple of amdgpu fixes
- some build fixes
- printk fix"
* tag 'drm-fixes-for-4.8-rc3' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: Change GART offset to 64-bit
drm/mediatek: add ARM_SMCCC dependency
drm/mediatek: add CONFIG_OF dependency
drm/mediatek: add COMMON_CLK dependency
drm/amdgpu: Fix memory trashing if UVD ring test fails
drm/amdgpu: fix vm init error path
drm/amdkfd: print doorbell offset as a hex value
Revert "drm/radeon: work around lack of upstream ACPI support for D3cold"
Revert "drm/amdgpu: work around lack of upstream ACPI support for D3cold"
This reverts commit:
fa7d81bb3c ("drm/fb-helper: Reduce READ_ONCE(master) to lockless_dereference")
As Peter explained:
[...] lockless_dereference() is _stronger_ than READ_ONCE(), not weaker.
[...]
Also, clue is in the name: 'dereference', you don't actually dereference
the pointer here, only load it.
My next patch breaks the compile without this revert, because it assumes
you want to deference and thus also need the struct type visible (which
it isn't here), so revert it.
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1470909022-687-1-git-send-email-johannes@sipsolutions.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull networking fixes from David Miller:
1) Buffers powersave frame test is reversed in cfg80211, fix from Felix
Fietkau.
2) Remove bogus WARN_ON in openvswitch, from Jarno Rajahalme.
3) Fix some tg3 ethtool logic bugs, and one that would cause no
interrupts to be generated when rx-coalescing is set to 0. From
Satish Baddipadige and Siva Reddy Kallam.
4) QLCNIC mailbox corruption and napi budget handling fix from Manish
Chopra.
5) Fix fib_trie logic when walking the trie during /proc/net/route
output than can access a stale node pointer. From David Forster.
6) Several sctp_diag fixes from Phil Sutter.
7) PAUSE frame handling fixes in mlxsw driver from Ido Schimmel.
8) Checksum fixup fixes in bpf from Daniel Borkmann.
9) Memork leaks in nfnetlink, from Liping Zhang.
10) Use after free in rxrpc, from David Howells.
11) Use after free in new skb_array code of macvtap driver, from Jason
Wang.
12) Calipso resource leak, from Colin Ian King.
13) mediatek bug fixes (missing stats sync init, etc.) from Sean Wang.
14) Fix bpf non-linear packet write helpers, from Daniel Borkmann.
15) Fix lockdep splats in macsec, from Sabrina Dubroca.
16) hv_netvsc bug fixes from Vitaly Kuznetsov, mostly to do with VF
handling.
17) Various tc-action bug fixes, from CONG Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net_sched: allow flushing tc police actions
net_sched: unify the init logic for act_police
net_sched: convert tcf_exts from list to pointer array
net_sched: move tc offload macros to pkt_cls.h
net_sched: fix a typo in tc_for_each_action()
net_sched: remove an unnecessary list_del()
net_sched: remove the leftover cleanup_a()
mlxsw: spectrum: Allow packets to be trapped from any PG
mlxsw: spectrum: Unmap 802.1Q FID before destroying it
mlxsw: spectrum: Add missing rollbacks in error path
mlxsw: reg: Fix missing op field fill-up
mlxsw: spectrum: Trap loop-backed packets
mlxsw: spectrum: Add missing packet traps
mlxsw: spectrum: Mark port as active before registering it
mlxsw: spectrum: Create PVID vPort before registering netdevice
mlxsw: spectrum: Remove redundant errors from the code
mlxsw: spectrum: Don't return upon error in removal path
i40e: check for and deal with non-contiguous TCs
ixgbe: Re-enable ability to toggle VLAN filtering
ixgbe: Force VLNCTRL.VFE to be set in all VMDq paths
...
As pointed out by Jamal, an action could be shared by
multiple filters, so we can't use list to chain them
any more after we get rid of the original tc_action.
Instead, we could just save pointers to these actions
in tcf_exts, since they are refcount'ed, so convert
the list to an array of pointers.
The "ugly" part is the action API still accepts list
as a parameter, I just introduce a helper function to
convert the array of pointers to a list, instead of
relying on the C99 feature to iterate the array.
Fixes: a85a970af2 ("net_sched: move tc_action into tcf_common")
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2016-08-16
This series contains fixes to e1000e, igb, ixgbe and i40e.
Kshitiz Gupta provides a fix for igb to resolve the PHY delay compensation
math in several functions.
Jarod Wilson provides a fix for e1000e which had to broken up into 2
patches, first is prepares the driver for expanding the list of NICs
that have occasional ~10 hour clock jumps when being used for PTP.
Second patch actually fixes i218 silicon which has been experiencing
the clock jumps while using PTP.
Alex provides 2 patches for ixgbe now that he is back at Intel. First
fixes setting VLNCTRL.VFE bit, which was left unchanged in earlier patches
which resulted in disabling VLAN filtering for all the VFs. Second
corrects the support for disabling the VLAN tag filtering via the
feature bit.
Lastly, David fixes i40e which was causing a kernel panic when
non-contiguous traffic classes or traffic classes not starting with TC0,
were configured on a link partner switch. To fix this, changed the
logic when determining the total number of TCs enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When packets enter the device they are classified to a priority group
(PG) buffer based on their PCP value. After their egress port and
traffic class are determined they are moved to the switch's shared
buffer and await transmission, if:
(Ingress{Port}.Usage < Thres && Ingress{Port,PG}.Usage < Thres &&
Egress{Port}.Usage < Thres && Egress{Port,TC}.Usage < Thres)
||
(Ingress{Port}.Usage < Min || Ingress{Port,PG} < Min ||
Egress{Port}.Usage < Min || Egress{Port,TC}.Usage < Min)
Packets scheduled to transmission through CPU port (trapped to CPU) use
traffic class 7, which has a zero maximum and minimum quotas. However,
when such packets arrive from PG 0 they are admitted to the shared
buffer as PG 0 has a non-zero minimum quota.
Allow all packets to be trapped to the CPU - regardless of the PG they
were classified to - by assigning a 10KB minimum quota for CPU port and
TC7.
Fixes: 8e8dfe9fdf ("mlxsw: spectrum: Add IEEE 802.1Qaz ETS support")
Reported-by: Tamir Winetroub <tamirw@mellanox.com>
Tested-by: Tamir Winetroub <tamirw@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before destroying the 802.1Q FID we should first remove the VID-to-FID
mapping. This makes mlxsw_sp_fid_destroy() symmetric with regards to
mlxsw_sp_fid_create().
Fixes: 14d39461b3 ("mlxsw: spectrum: Use per-FID struct for the VLAN-aware bridge")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While going over the code I noticed we are missing two rollbacks in the
port's creation error path. Add them and adjust the place of one of them
in the port's removal sequence so that both are symmetric.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ralue pack function needs to set op, otherwise it is 0 for add always.
Fixes: d5a1c749d2 ("mlxsw: reg: Add Router Algorithmic LPM Unicast Entry Register definition")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the conditions to generate an ICMP Redirect Message is that "the
packet is being forwarded out the same physical interface that it was
received from" (RFC 1812).
Therefore, we need to be able to trap such packets and let the kernel
decide what to do with them.
For each RIF, enable the loop-back filter, which will raise the LBERROR
trap whenever the ingress RIF equals the egress RIF.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Reported-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following traps:
1) MTU Error: Trap packets whose size is bigger than the egress RIF's
MTU. If DF bit isn't set, traffic will continue to be routed in slow
path.
2) TTL Error: Trap packets whose TTL expired. This allows traceroute to
work properly.
3) OSPF packets.
Fixes: 7b27ce7bb9 ("mlxsw: spectrum: Add traps needed for router implementation")
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bbf2a4757b ("mlxsw: spectrum: Initialize ports at the end of
init sequence") moved ports initialization to the end of the init
sequence, which means ports are the first to be removed during fini.
Since the FDB delayed work is still active when ports are removed it's
possible for it to process FDB notifications of inactive ports,
resulting in a warning message.
Fix that by marking ports as inactive only after unregistering them. The
NETDEV_UNREGISTER event will invoke bridge's driver port removal
sequence that will cause the FDB (and FDB notifications) to be flushed.
Fixes: bbf2a4757b ("mlxsw: spectrum: Initialize ports at the end of init sequence")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After registering a netdevice it's possible for user space applications
to configure an IP address on it. From the driver's perspective, this
means a router interface (RIF) should be created for the PVID vPort.
Therefore, we must create the PVID vPort before registering the
netdevice.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when device configuration fails we emit errors to the kernel
log despite the fact we already get these from the EMAD transaction
layer, so remove them.
In addition to being unnecessary, removing these error messages will
allow us to reuse mlxsw_sp_port_add_vid() to create the PVID vPort
before registering the netdevice.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a VLAN filter from the device we shouldn't return upon the
first error we encounter, as otherwise we'll have resources that will
never be freed nor used.
Instead, we should keep trying to free as much resources as possible in
a best effort mode.
Remove the error message as well, since we already get these from the
EMAD transaction code.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The raid0 MD personality does not start a raid0 array with any of its
data devices missing.
dm-raid was removing data/metadata device pairs unconditionally if it
failed to read a superblock off the respective metadata device of such
pair, resulting in failure to start arrays with the raid0 personality.
Avoid removing any data/metadata device pairs in case of raid0
(e.g. lvm2 segment type 'raid0_meta') thus allowing MD to start the
array.
Also, avoid region size validation for raid0.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
In commit:
d8152bf85d ("clocksource/drivers/mips-gic-timer: Convert init function to return error")
several return values were added to a void function resulting in the following warnings:
clocksource/mips-gic-timer.c: In function 'gic_clocksource_of_init':
clocksource/mips-gic-timer.c:175:3: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:183:4: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:190:3: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:195:3: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:200:3: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:211:2: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c: At top level:
clocksource/mips-gic-timer.c:213:1: warning: comparison of distinct pointer types lacks a cast [enabled by default]
clocksource/mips-gic-timer.c: In function 'gic_clocksource_of_init':
clocksource/mips-gic-timer.c:183:18: warning: ignoring return value of 'PTR_ERR', declared with attribute warn_unused_result [-Wunused-result]
Given that the addition of the return values was intentional, it seems
that the conversion of the containing function from void to int was
simply overlooked.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Fixes: d8152bf85d ("clocksource/drivers/mips-gic-timer: Convert init function to return error")
Link: http://lkml.kernel.org/r/1471429296-9053-3-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I could not figure out why, but GCC cannot prove that the
kona_timer_init() function always initializes its two outputs,
and we get a warning for the use of the 'lsw' variable later,
which is obviously correct.
drivers/clocksource/bcm_kona_timer.c: In function 'kona_timer_init':
drivers/clocksource/bcm_kona_timer.c:119:13: error: 'lsw' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Slightly reordering the loop makes the warning disappear, after
it becomes more obvious to the compiler that the loop is
always entered on the first iteration.
As pointed out by Ray Jui, there is a related problem in the
way we deal with the loop running into the limit, as we just
keep going there with an invalid counter data, so instead we
now propagate a -ETIMEDOUT result to the caller.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bcm-kernel-feedback-list@broadcom.com
Link: http://lkml.kernel.org/r/1471429296-9053-2-git-send-email-daniel.lezcano@linaro.org
Link: https://patchwork.kernel.org/patch/9174261/
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While converting the init function to return an error, the wrong clock
was get. This leads to the wrong clock rate and slows down the kernel.
For example, it affects typical boot time:
- without fix: over 1 minute
- with fix: 15 seconds
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 12549e27c6 ("clocksource/drivers/time-armada-370-xp: Convert init function to return error")
Link: http://lkml.kernel.org/r/1471429296-9053-1-git-send-email-daniel.lezcano@linaro.org
[ Refined the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- Test fixes.
- A vsock fix.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXsSOEAAoJECgfDbjSjVRpmCIIAKe6m+gWBiC4GJHJTYP5Q+lR
c6meEwxMBTZ+EVSeqUrAIN7slXu/w4NMVE/7IOo9Y+OUGK9MpQiRDOTzw2m3ps8d
W2gEJ+kvc7wFZZKXPkrgvzSuct0yv2Ho+lhZ9wpENU8KulyjBjAZ4xUDw/4LPM7G
nmE8GwOx625N4KCJh3dw5jZsgdyVWzqPuVYUqFctOWdDEqEs4f/Zb3kHR81DoMai
crri3p0fDOo+9zYPDTteG1ILayY6yIIFiPx8jrHTdL9DS+LcBHYJMXunu4Ensjth
9xdJeqWyb20DjSjzhrjwxS7Li4FJDiG5xYHNfuf2OQb+Or7ZvUGga1PbaNa7m6I=
=nlXU
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio/vhost fixes from Michael Tsirkin:
- test fixes
- a vsock fix
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
tools/virtio: add dma stubs
vhost/test: fix after swiotlb changes
vhost/vsock: drop space available check for TX vq
ringtest: test build fix