commit 9aad71144f upstream.
The ibmasm_send_i2o_message() function uses get_dot_command_size() to
compute the byte count for memcpy_toio(), but this value is derived from
user-controlled fields in the dot_command_header (command_size: u8,
data_size: u16) and is never validated against the actual allocation size.
A root user can write a small buffer with inflated header fields, causing
memcpy_toio() to read up to ~65 KB past the end of the allocation into
adjacent kernel heap, which is then forwarded to the service processor
over MMIO.
Silently clamping the copy size is not sufficient: if the header fields
claim a larger size than the buffer, the SP receives a dot command whose
own header is inconsistent with the I2O message length, which can cause
the SP to desynchronize. Reject such commands outright by returning
failure.
Validate command_size before calling get_mfa_inbound() to avoid leaking
an I2O message frame: reading INBOUND_QUEUE_PORT dequeues a hardware
frame from the controller's free pool, and returning without a
corresponding set_mfa_inbound() call would permanently exhaust it.
Additionally, clamp command_size to I2O_COMMAND_SIZE before the
memcpy_toio() so the MMIO write stays within the I2O message frame,
consistent with the clamping already performed by outgoing_message_size()
for the header field.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Yuhao Jiang <danisjiang@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tyllis Xu <LivelyCarpet87@gmail.com>
Link: https://patch.msgid.link/20260314165805.548293-1-LivelyCarpet87@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0eb09f7374 upstream.
The command_file_write() handler allocates a kernel buffer of exactly
count bytes and copies user data into it, but does not validate the
buffer against the dot command protocol before passing it to
get_dot_command_size() and get_dot_command_timeout().
Since both the allocation size (count) and the header fields (command_size,
data_size) are independently user-controlled, an attacker can cause
get_dot_command_size() to return a value exceeding the allocation,
triggering OOB reads in get_dot_command_timeout() and an out-of-bounds
memcpy_toio() that leaks kernel heap memory to the service processor.
Fix with two guards: reject writes smaller than sizeof(struct
dot_command_header) before allocation, then after copying user data
reject commands where the buffer is smaller than the total size declared
by the header (sizeof(header) + command_size + data_size). This ensures
all subsequent header and payload field accesses stay within the buffer.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Yuhao Jiang <danisjiang@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tyllis Xu <LivelyCarpet87@gmail.com>
Link: https://patch.msgid.link/20260314165355.548119-1-LivelyCarpet87@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b6e6ead55 upstream.
ibmasm_handle_mouse_interrupt() performs an out-of-bounds MMIO read
when the queue reader or writer index from hardware exceeds
REMOTE_QUEUE_SIZE (60).
A compromised service processor can trigger this by writing an
out-of-range value to the reader or writer MMIO register before
asserting an interrupt. Since writer is re-read from hardware on
every loop iteration, it can also be set to an out-of-range value
after the loop has already started.
The root cause is that get_queue_reader() and get_queue_writer() return
raw readl() values that are passed directly into get_queue_entry(),
which computes:
queue_begin + reader * sizeof(struct remote_input)
with no bounds check. This unchecked MMIO address is then passed to
memcpy_fromio(), reading 8 bytes from unintended device registers.
For sufficiently large values the address falls outside the PCI BAR
mapping entirely, triggering a machine check exception.
Fix by checking both indices against REMOTE_QUEUE_SIZE at the top of
the loop body, before any call to get_queue_entry(). On an out-of-range
value, reset the reader register to 0 via set_queue_reader() before
breaking, so that normal queue operation can resume if the corrupted
hardware state is transient.
Reported-by: Yuhao Jiang <danisjiang@gmail.com>
Fixes: 278d72ae88 ("[PATCH] ibmasm driver: redesign handling of remote control events")
Cc: stable@vger.kernel.org
Cc: ychen@northwestern.edu
Signed-off-by: Tyllis Xu <LivelyCarpet87@gmail.com>
Link: https://patch.msgid.link/20260308062108.258940-1-LivelyCarpet87@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b54c82d6cb ]
commit 14374fbb3f ("misc: eeprom_93xx46: Add new 93c56 and 93c66
compatible strings") added support for 93xx56 and 93xx66 eeproms, but
didn't take into account that the write enable/disable + erase all
commands are hardcoded for the 6-bit address of the 93xx46.
This commit fixes the command word generation by increasing the number
of shifts as the address field grows, keeping the command intact.
Also, the check for 8-bit or 16-bit mode is no longer required as this
is already taken into account in the edev->addrlen field.
Signed-off-by: Markus Perkins <markus@notsyncing.net>
Link: https://patch.msgid.link/20251202104823.429869-3-markus@notsyncing.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06d5a7afe1 ]
The commit
afd2627f72 ("tracing: Check "%s" dereference via the field and not the TP_printk format")
forbids to emit event with a plain char* without a wrapper.
The reg parameter always passed as static string and wrapper
is not strictly required, contrary to dev parameter.
Use the string wrapper anyway to check sanity of the reg parameters,
store it value independently and prevent internal kernel data leaks.
Since some code refactoring has taken place, explicit backporting may
be needed for kernels older than 6.10.
Cc: stable@vger.kernel.org # v6.11+
Fixes: a0a927d06d ("mei: me: add io register tracing")
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Link: https://patch.msgid.link/20260111145125.1754912-1-alexander.usyskin@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ adapted __assign_str() calls to use two arguments ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26c08dabe5 upstream.
Directly calling `put_queue` carries risks since it cannot
guarantee that resources of `uacce_queue` have been fully released
beforehand. So adding a `stop_queue` operation for the
UACCE_CMD_PUT_Q command and leaving the `put_queue` operation to
the final resource release ensures safety.
Queue states are defined as follows:
- UACCE_Q_ZOMBIE: Initial state
- UACCE_Q_INIT: After opening `uacce`
- UACCE_Q_STARTED: After `start` is issued via `ioctl`
When executing `poweroff -f` in virt while accelerator are still
working, `uacce_fops_release` and `uacce_remove` may execute
concurrently. This can cause `uacce_put_queue` within
`uacce_fops_release` to access a NULL `ops` pointer. Therefore, add
state checks to prevent accessing freed pointers.
Fixes: 015d239ac0 ("uacce: add uacce driver")
Cc: stable@vger.kernel.org
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Link: https://patch.msgid.link/20251202061256.4158641-5-huangchenghai2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02695347be upstream.
The current uacce_vm_ops does not support the mremap operation of
vm_operations_struct. Implement .mremap to return -EPERM to remind
users.
The reason we need to explicitly disable mremap is that when the
driver does not implement .mremap, it uses the default mremap
method. This could lead to a risk scenario:
An application might first mmap address p1, then mremap to p2,
followed by munmap(p1), and finally munmap(p2). Since the default
mremap copies the original vma's vm_private_data (i.e., q) to the
new vma, both munmap operations would trigger vma_close, causing
q->qfr to be freed twice(qfr will be set to null here, so repeated
release is ok).
Fixes: 015d239ac0 ("uacce: add uacce driver")
Cc: stable@vger.kernel.org
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Link: https://patch.msgid.link/20251202061256.4158641-4-huangchenghai2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3bece3678 upstream.
When cdev_device_add fails, it internally releases the cdev memory,
and if cdev_device_del is then executed, it will cause a hang error.
To fix it, we check the return value of cdev_device_add() and clear
uacce->cdev to avoid calling cdev_device_del in the uacce_remove.
Fixes: 015d239ac0 ("uacce: add uacce driver")
Cc: stable@vger.kernel.org
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Link: https://patch.msgid.link/20251202061256.4158641-2-huangchenghai2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 420f423def upstream.
Add Nova Lake S device id.
Cc: stable <stable@kernel.org>
Co-developed-by: Tomas Winkler <tomasw@gmail.com>
Signed-off-by: Tomas Winkler <tomasw@gmail.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Link: https://patch.msgid.link/20251215105915.1672659-1-alexander.usyskin@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 15504b1163 ]
Let's move the removal of the page from the balloon list into the single
caller, to remove the dependency on the PG_isolated flag and clarify
locking requirements.
Note that for now, balloon_page_delete() was used on two paths:
(1) Removing a page from the balloon for deflation through
balloon_page_list_dequeue()
(2) Removing an isolated page from the balloon for migration in the
per-driver migration handlers. Isolated pages were already removed from
the balloon list during isolation.
So instead of relying on the flag, we can just distinguish both cases
directly and handle it accordingly in the caller.
We'll shuffle the operations a bit such that they logically make more
sense (e.g., remove from the list before clearing flags).
In balloon migration functions we can now move the balloon_page_finalize()
out of the balloon lock and perform the finalization just before dropping
the balloon reference.
Document that the page lock is currently required when modifying the
movability aspects of a page; hopefully we can soon decouple this from the
page lock.
Link: https://lkml.kernel.org/r/20250704102524.326966-3-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Brendan Jackman <jackmanb@google.com>
Cc: Byungchul Park <byungchul@sk.com>
Cc: Chengming Zhou <chengming.zhou@linux.dev>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Eugenio Pé rez <eperezma@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Gregory Price <gourry@gourry.net>
Cc: Harry Yoo <harry.yoo@oracle.com>
Cc: "Huang, Ying" <ying.huang@linux.alibaba.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Jerrin Shaji George <jerrin.shaji-george@broadcom.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Joshua Hahn <joshua.hahnjy@gmail.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Mathew Brost <matthew.brost@intel.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Naoya Horiguchi <nao.horiguchi@gmail.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Peter Xu <peterx@redhat.com>
Cc: Qi Zheng <zhengqi.arch@bytedance.com>
Cc: Rakie Kim <rakie.kim@sk.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Shakeel Butt <shakeel.butt@linux.dev>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Cc: xu xin <xu.xin16@zte.com.cn>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stable-dep-of: 0da2ba35c0 ("powerpc/pseries/cmm: adjust BALLOON_MIGRATE when migrating pages")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6b26053819 ]
There is a dev_err message that is reporting the value of
cmd->asiv_length when it should be reporting cmd->asv_length
instead. Fix this.
Fixes: eaf4722d46 ("GenWQE Character device and DDCB queue")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20250902113712.2624743-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 966c5cd72b upstream.
When a card is present in the reader, the driver currently defers
autosuspend by returning -EAGAIN during the suspend callback to
trigger USB remote wakeup signaling. However, this does not guarantee
that the mmc child device has been resumed, which may cause issues if
it remains suspended while the card is accessible.
This patch ensures that all child devices, including the mmc host
controller, are explicitly resumed before returning -EAGAIN. This
fixes a corner case introduced by earlier remote wakeup handling,
improving reliability of runtime PM when a card is inserted.
Fixes: 883a87ddf2 ("misc: rtsx_usb: Use USB remote wakeup signaling for card insertion detection")
Cc: stable@vger.kernel.org
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20250711140143.2105224-1-ricky_wu@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8f5d9bed61 ]
This reverts commit bfb4cf9fb9.
While the code "looks" correct, the compiler has no way to know that
doing "fun" pointer math like this really isn't a write off the end of
the structure as there is no hint anywhere that the structure has data
at the end of it.
This causes the following build warning:
In function 'fortify_memset_chk',
inlined from 'ctx_fire_notification.isra' at drivers/misc/vmw_vmci/vmci_context.c:254:3:
include/linux/fortify-string.h:480:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
480 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
So revert it for now and it can come back in the future in a "sane" way
that either correctly makes the structure know that there is trailing
data, OR just the payload structure is properly referenced and zeroed
out.
Fixes: bfb4cf9fb9 ("vmci: Prevent the dispatching of uninitialized payloads")
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Lizhi Xu <lizhi.xu@windriver.com>
Link: https://lore.kernel.org/r/20250703171021.0aee1482@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfb4cf9fb9 ]
The reproducer executes the host's unlocked_ioctl call in two different
tasks. When init_context fails, the struct vmci_event_ctx is not fully
initialized when executing vmci_datagram_dispatch() to send events to all
vm contexts. This affects the datagram taken from the datagram queue of
its context by another task, because the datagram payload is not initialized
according to the size payload_size, which causes the kernel data to leak
to the user space.
Before dispatching the datagram, and before setting the payload content,
explicitly set the payload content to 0 to avoid data leakage caused by
incomplete payload initialization.
Fixes: 28d6692cd8 ("VMCI: context implementation.")
Reported-by: syzbot+9b9124ae9b12d5af5d95@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=9b9124ae9b12d5af5d95
Tested-by: syzbot+9b9124ae9b12d5af5d95@syzkaller.appspotmail.com
Signed-off-by: Lizhi Xu <lizhi.xu@windriver.com>
Link: https://lore.kernel.org/r/20250627055214.2967129-1-lizhi.xu@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1bd6406fb5 upstream.
During our test, it is found that a warning can be trigger in try_grab_folio
as follow:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1678 at mm/gup.c:147 try_grab_folio+0x106/0x130
Modules linked in:
CPU: 0 UID: 0 PID: 1678 Comm: syz.3.31 Not tainted 6.15.0-rc5 #163 PREEMPT(undef)
RIP: 0010:try_grab_folio+0x106/0x130
Call Trace:
<TASK>
follow_huge_pmd+0x240/0x8e0
follow_pmd_mask.constprop.0.isra.0+0x40b/0x5c0
follow_pud_mask.constprop.0.isra.0+0x14a/0x170
follow_page_mask+0x1c2/0x1f0
__get_user_pages+0x176/0x950
__gup_longterm_locked+0x15b/0x1060
? gup_fast+0x120/0x1f0
gup_fast_fallback+0x17e/0x230
get_user_pages_fast+0x5f/0x80
vmci_host_unlocked_ioctl+0x21c/0xf80
RIP: 0033:0x54d2cd
---[ end trace 0000000000000000 ]---
Digging into the source, context->notify_page may init by get_user_pages_fast
and can be seen in vmci_ctx_unset_notify which will try to put_page. However
get_user_pages_fast is not finished here and lead to following
try_grab_folio warning. The race condition is shown as follow:
cpu0 cpu1
vmci_host_do_set_notify
vmci_host_setup_notify
get_user_pages_fast(uva, 1, FOLL_WRITE, &context->notify_page);
lockless_pages_from_mm
gup_pgd_range
gup_huge_pmd // update &context->notify_page
vmci_host_do_set_notify
vmci_ctx_unset_notify
notify_page = context->notify_page;
if (notify_page)
put_page(notify_page); // page is freed
__gup_longterm_locked
__get_user_pages
follow_trans_huge_pmd
try_grab_folio // warn here
To slove this, use local variable page to make notify_page can be seen
after finish get_user_pages_fast.
Fixes: a1d88436d5 ("VMCI: Fix two UVA mapping bugs")
Cc: stable <stable@kernel.org>
Closes: https://lore.kernel.org/all/e91da589-ad57-3969-d979-879bbd10dddd@huawei.com/
Signed-off-by: Wupeng Ma <mawupeng1@huawei.com>
Link: https://lore.kernel.org/r/20250510033040.901582-1-mawupeng1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit baaef0a274 upstream.
There are two variables that indicate the interrupt type to be used
in the next test execution, "irq_type" as global and "test->irq_type".
The global is referenced from pci_endpoint_test_get_irq() to preserve
the current type for ioctl(PCITEST_GET_IRQTYPE).
The type set in this function isn't reflected in the global "irq_type",
so ioctl(PCITEST_GET_IRQTYPE) returns the previous type.
As a result, the wrong type is displayed in old version of "pcitest"
as follows:
- Result of running "pcitest -i 0"
SET IRQ TYPE TO LEGACY: OKAY
- Result of running "pcitest -I"
GET IRQ TYPE: MSI
Whereas running the new version of "pcitest" in kselftest results in an
error as follows:
# RUN pci_ep_basic.LEGACY_IRQ_TEST ...
# pci_endpoint_test.c:104:LEGACY_IRQ_TEST:Expected 0 (0) == ret (1)
# pci_endpoint_test.c:104:LEGACY_IRQ_TEST:Can't get Legacy IRQ type
Fix this issue by propagating the current type to the global "irq_type".
Fixes: b2ba9225e0 ("misc: pci_endpoint_test: Avoid using module parameter to determine irqtype")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250225110252.28866-5-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 919d14603d upstream.
There are two variables that indicate the interrupt type to be used
in the next test execution, global "irq_type" and "test->irq_type".
The former is referenced from pci_endpoint_test_get_irq() to preserve
the current type for ioctl(PCITEST_GET_IRQTYPE).
In the pci_endpoint_test_request_irq(), since this global variable
is referenced when an error occurs, the unintended error message is
displayed.
For example, after running "pcitest -i 2", the following message
shows "MSI 3" even if the current IRQ type becomes "MSI-X":
pci-endpoint-test 0000:01:00.0: Failed to request IRQ 30 for MSI 3
SET IRQ TYPE TO MSI-X: NOT OKAY
Fix this issue by using "test->irq_type" instead of global "irq_type".
Cc: stable@vger.kernel.org
Fixes: b2ba9225e0 ("misc: pci_endpoint_test: Avoid using module parameter to determine irqtype")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20250225110252.28866-4-hayashi.kunihiko@socionext.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6cb7828c8 upstream.
After devm_request_irq() fails with error in pci_endpoint_test_request_irq(),
the pci_endpoint_test_free_irq_vectors() is called assuming that all IRQs
have been released.
However, some requested IRQs remain unreleased, so there are still
/proc/irq/* entries remaining, and this results in WARN() with the
following message:
remove_proc_entry: removing non-empty directory 'irq/30', leaking at least 'pci-endpoint-test.0'
WARNING: CPU: 0 PID: 202 at fs/proc/generic.c:719 remove_proc_entry +0x190/0x19c
To solve this issue, set the number of remaining IRQs to test->num_irqs,
and release IRQs in advance by calling pci_endpoint_test_release_irq().
Cc: stable@vger.kernel.org
Fixes: e03327122e ("pci_endpoint_test: Add 2 ioctl commands")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20250225110252.28866-3-hayashi.kunihiko@socionext.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 038ef0754a upstream.
The dev_id value in the GPIO lookup table must match to
the device instance name, which in this case is combined
of name and platform device ID, i.e. "spi_gpio.1". But
the table assumed that there was no platform device ID
defined, which is wrong. Fix the dev_id value accordingly.
Fixes: 9b00bc7b90 ("spi: spi-gpio: Rewrite to use GPIO descriptors")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250206220311.1554075-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ca4ea1f88 upstream.
For registered buffers, fastrpc driver sends the buffer information
to remote subsystem. There is a problem with current implementation
where the page address is being sent with an offset leading to
improper buffer address on DSP. This is leads to functional failures
as DSP expects base address in page information and extracts offset
information from remote arguments. Mask the offset and pass the base
page address to DSP.
This issue is observed is a corner case when some buffer which is registered
with fastrpc framework is passed with some offset by user and then the DSP
implementation tried to read the data. As DSP expects base address and takes
care of offsetting with remote arguments, passing an offsetted address will
result in some unexpected data read in DSP.
All generic usecases usually pass the buffer as it is hence is problem is
not usually observed. If someone tries to pass offsetted buffer and then
tries to compare data at HLOS and DSP end, then the ambiguity will be observed.
Fixes: 80f3afd72b ("misc: fastrpc: consider address offset before sending to DSP")
Cc: stable@kernel.org
Signed-off-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20250110134239.123603-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 235b630eda upstream.
This commit reintroduces interrupt-based card detection previously
used in the rts5139 driver. This functionality was removed in commit
00d8521dcd ("staging: remove rts5139 driver code").
Reintroducing this mechanism fixes presence detection for certain card
readers, which with the current driver, will taken approximately 20
seconds to enter S3 as `mmc_rescan` has to be frozen.
Fixes: 00d8521dcd ("staging: remove rts5139 driver code")
Cc: stable@vger.kernel.org
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Link: https://lore.kernel.org/r/20241119085815.11769-1-sean@starlabs.systems
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7738a7ab9d ]
Add a quirk similar to eeprom_93xx46 to add an extra clock cycle before
reading data from the EEPROM.
The 93Cx6 family of EEPROMs output a "dummy 0 bit" between the writing
of the op-code/address from the host to the EEPROM and the reading of
the actual data from the EEPROM.
More info can be found on page 6 of the AT93C46 datasheet (linked below).
Similar notes are found in other 93xx6 datasheets.
In summary the read operation for a 93Cx6 EEPROM is:
Write to EEPROM: 110[A5-A0] (9 bits)
Read from EEPROM: 0[D15-D0] (17 bits)
Where:
110 is the start bit and READ OpCode
[A5-A0] is the address to read from
0 is a "dummy bit" preceding the actual data
[D15-D0] is the actual data.
Looking at the READ timing diagrams in the 93Cx6 datasheets the dummy
bit should be clocked out on the last address bit clock cycle meaning it
should be discarded naturally.
However, depending on the hardware configuration sometimes this dummy
bit is not discarded. This is the case with Exar PCI UARTs which require
an extra clock cycle between sending the address and reading the data.
Datasheet: https://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-5193-SEEPROM-AT93C46D-Datasheet.pdf
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/0f23973efefccd2544705a0480b4ad4c2353e407.1727880931.git.pnewman@connecttech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c5d8b819d ]
The pm_runtime_disable() is missing in probe error path,
so add it to fix it.
Fixes: 92b1f84d46 ("drivers/misc: driver for APDS990X ALS and proximity sensors")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20240923035556.3009105-1-ruanjinjie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b983b27166 ]
Disabling preemption in the GRU driver is unnecessary, and clashes with
sleeping locks in several code paths. Remove preempt_disable and
preempt_enable from the GRU driver.
Signed-off-by: Dimitri Sivanich <sivanich@hpe.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b82641ad0 ]
The update to support other (bigger) types of EEPROMs broke
the driver loading due to removal of the default size.
Fix this by adding the respective (new) flag to the platform data.
Fixes: 14374fbb3f ("misc: eeprom_93xx46: Add new 93c56 and 93c66 compatible strings")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240508184905.2102633-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 48b9a8dabc upstream.
When removing a resource from vmci_resource_table in
vmci_resource_remove(), the search is performed using the resource
handle by comparing context and resource fields.
It is possible though to create two resources with different types
but same handle (same context and resource fields).
When trying to remove one of the resources, vmci_resource_remove()
may not remove the intended one, but the object will still be freed
as in the case of the datagram type in vmci_datagram_destroy_handle().
vmci_resource_table will still hold a pointer to this freed resource
leading to a use-after-free vulnerability.
BUG: KASAN: use-after-free in vmci_handle_is_equal include/linux/vmw_vmci_defs.h:142 [inline]
BUG: KASAN: use-after-free in vmci_resource_remove+0x3a1/0x410 drivers/misc/vmw_vmci/vmci_resource.c:147
Read of size 4 at addr ffff88801c16d800 by task syz-executor197/1592
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x82/0xa9 lib/dump_stack.c:106
print_address_description.constprop.0+0x21/0x366 mm/kasan/report.c:239
__kasan_report.cold+0x7f/0x132 mm/kasan/report.c:425
kasan_report+0x38/0x51 mm/kasan/report.c:442
vmci_handle_is_equal include/linux/vmw_vmci_defs.h:142 [inline]
vmci_resource_remove+0x3a1/0x410 drivers/misc/vmw_vmci/vmci_resource.c:147
vmci_qp_broker_detach+0x89a/0x11b9 drivers/misc/vmw_vmci/vmci_queue_pair.c:2182
ctx_free_ctx+0x473/0xbe1 drivers/misc/vmw_vmci/vmci_context.c:444
kref_put include/linux/kref.h:65 [inline]
vmci_ctx_put drivers/misc/vmw_vmci/vmci_context.c:497 [inline]
vmci_ctx_destroy+0x170/0x1d6 drivers/misc/vmw_vmci/vmci_context.c:195
vmci_host_close+0x125/0x1ac drivers/misc/vmw_vmci/vmci_host.c:143
__fput+0x261/0xa34 fs/file_table.c:282
task_work_run+0xf0/0x194 kernel/task_work.c:164
tracehook_notify_resume include/linux/tracehook.h:189 [inline]
exit_to_user_mode_loop+0x184/0x189 kernel/entry/common.c:187
exit_to_user_mode_prepare+0x11b/0x123 kernel/entry/common.c:220
__syscall_exit_to_user_mode_work kernel/entry/common.c:302 [inline]
syscall_exit_to_user_mode+0x18/0x42 kernel/entry/common.c:313
do_syscall_64+0x41/0x85 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x6e/0x0
This change ensures the type is also checked when removing
the resource from vmci_resource_table in vmci_resource_remove().
Fixes: bc63dedb7d ("VMCI: resource object implementation.")
Cc: stable@vger.kernel.org
Reported-by: George Kennedy <george.kennedy@oracle.com>
Signed-off-by: David Fernandez Gonzalez <david.fernandez.gonzalez@oracle.com>
Link: https://lore.kernel.org/r/20240828154338.754746-1-david.fernandez.gonzalez@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1db5322b7e ]
Change level for the "not connected" client message in the write
callback from error to debug.
The MEI driver currently disconnects all clients upon system suspend.
This behavior is by design and user-space applications with
open connections before the suspend are expected to handle errors upon
resume, by reopening their handles, reconnecting,
and retrying their operations.
However, the current driver implementation logs an error message every
time a write operation is attempted on a disconnected client.
Since this is a normal and expected flow after system resume
logging this as an error can be misleading.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20240530091415.725247-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8003f00d89 upstream.
Coverity spotted that event_msg is controlled by user-space,
event_msg->event_data.event is passed to event_deliver() and used
as an index without sanitization.
This change ensures that the event index is sanitized to mitigate any
possibility of speculative information leaks.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Only compile tested, no access to HW.
Fixes: 1d990201f9 ("VMCI: event handling implementation.")
Cc: stable <stable@kernel.org>
Signed-off-by: Hagar Gamal Halim Hemdan <hagarhem@amazon.com>
Link: https://lore.kernel.org/stable/20231127193533.46174-1-hagarhem%40amazon.com
Link: https://lore.kernel.org/r/20240430085916.4753-1-hagarhem@amazon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 283cb234ef upstream.
The mei_me_pci_resume doesn't release irq on the error path,
in case mei_start() fails.
Cc: <stable@kernel.org>
Fixes: 33ec082631 ("mei: revamp mei reset state machine")
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20240604090728.1027307-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee59be35d7 ]
In __pci_register_driver(), the pci core overwrites the dev_groups field of
the embedded struct device_driver with the dev_groups from the outer
struct pci_driver unconditionally.
Set dev_groups in the pci_driver to make sure it is used.
This was broken since the introduction of pvpanic-pci.
Fixes: db3a4f0abe ("misc/pvpanic: add PCI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Fixes: ded13b9cfd ("PCI: Add support for dev_groups to struct pci_driver")
Link: https://lore.kernel.org/r/20240411-pvpanic-pci-dev-groups-v1-1-db8cb69f1b09@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1426d392a ]
pvpanic-mmio.c and pvpanic-pci.c share a lot of code.
Refactor it into pvpanic.c where it doesn't have to be kept in sync
manually and where the core logic can be understood more easily.
No functional change.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20231011-pvpanic-cleanup-v2-1-4b21d56f779f@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: ee59be35d7 ("misc/pvpanic-pci: register attributes via pci_driver")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33a4304194 ]
We have different style on where we place module_*() and MODULE_*() macros.
Inherit the style from the original module (now pvpanic-mmio.c).
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210829124354.81653-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: ee59be35d7 ("misc/pvpanic-pci: register attributes via pci_driver")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f42c97027f ]
If the eeprom is not accessible, an nvmem device will be registered, the
read will fail, and the device will be torn down. If another driver
accesses the nvmem device after the teardown, it will reference
invalid memory.
Move the failure point before registering the nvmem device.
Signed-off-by: Daniel Okazaki <dtokazaki@google.com>
Fixes: b20eb4c1f0 ("eeprom: at24: drop unnecessary label")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240422174337.2487142-1-dtokazaki@google.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit caba40ec35 ]
The DDR3 SPD data structure advertises the presence of a thermal
sensor on a DDR3 module in byte 32, bit 7. Let's use this information
to explicitly instantiate the thermal sensor I2C client instead of
having to rely on class-based I2C probing.
The temp sensor i2c address can be derived from the SPD i2c address,
so we can directly instantiate the device and don't have to probe
for it. If the temp sensor has been instantiated already by other
means (e.g. class-based auto-detection), then the busy-check in
i2c_new_client_device will detect this.
Note: Thermal sensors on DDR4 DIMM's are instantiated from the
ee1004 driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/68113672-3724-44d5-9ff8-313dd6628f8c@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: f42c97027f ("eeprom: at24: fix memory corruption race condition")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a3c10035d1 ]
When using nvmem layouts it is possible devm_nvmem_register returns
-EPROBE_DEFER, resulting in an 'empty' in
/sys/kernel/debug/devices_deferred. Use dev_err_probe for providing
additional information.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: f42c97027f ("eeprom: at24: fix memory corruption race condition")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0dc04112be upstream.
Extend the quirk to disable MEI interface on Intel PCH Ignition (IGN)
and SPS firmwares for RPL-S devices. These firmwares do not support
the MEI protocol.
Fixes: 3ed8c7d39c ("mei: me: add raptor lake point S DID")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20240312051958.118478-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e606e4b717 upstream.
The changes are similar to those given in the commit 19b070fefd
("VMCI: Fix memcpy() run-time warning in dg_dispatch_as_host()").
Fix filling of the msg and msg_payload in dg_info struct, which prevents a
possible "detected field-spanning write" of memcpy warning that is issued
by the tracking mechanism __fortify_memcpy_chk.
Signed-off-by: Vasiliy Kovalev <kovalev@altlinux.org>
Link: https://lore.kernel.org/r/20240219105315.76955-1-kovalev@altlinux.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 19b070fefd ]
Syzkaller hit 'WARNING in dg_dispatch_as_host' bug.
memcpy: detected field-spanning write (size 56) of single field "&dg_info->msg"
at drivers/misc/vmw_vmci/vmci_datagram.c:237 (size 24)
WARNING: CPU: 0 PID: 1555 at drivers/misc/vmw_vmci/vmci_datagram.c:237
dg_dispatch_as_host+0x88e/0xa60 drivers/misc/vmw_vmci/vmci_datagram.c:237
Some code commentry, based on my understanding:
544 #define VMCI_DG_SIZE(_dg) (VMCI_DG_HEADERSIZE + (size_t)(_dg)->payload_size)
/// This is 24 + payload_size
memcpy(&dg_info->msg, dg, dg_size);
Destination = dg_info->msg ---> this is a 24 byte
structure(struct vmci_datagram)
Source = dg --> this is a 24 byte structure (struct vmci_datagram)
Size = dg_size = 24 + payload_size
{payload_size = 56-24 =32} -- Syzkaller managed to set payload_size to 32.
35 struct delayed_datagram_info {
36 struct datagram_entry *entry;
37 struct work_struct work;
38 bool in_dg_host_queue;
39 /* msg and msg_payload must be together. */
40 struct vmci_datagram msg;
41 u8 msg_payload[];
42 };
So those extra bytes of payload are copied into msg_payload[], a run time
warning is seen while fuzzing with Syzkaller.
One possible way to fix the warning is to split the memcpy() into
two parts -- one -- direct assignment of msg and second taking care of payload.
Gustavo quoted:
"Under FORTIFY_SOURCE we should not copy data across multiple members
in a structure."
Reported-by: syzkaller <syzkaller@googlegroups.com>
Suggested-by: Vegard Nossum <vegard.nossum@oracle.com>
Suggested-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/20240105164001.2129796-2-harshit.m.mogalapalli@oracle.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a4e61de63e upstream.
In remoteproc shutdown sequence, rpmsg_remove will get called which
would depopulate all the child nodes that have been created during
rpmsg_probe. This would result in cb_remove call for all the context
banks for the remoteproc. In cb_remove function, session 0 is
getting skipped which is not correct as session 0 will never become
available again. Add changes to mark session 0 also as invalid.
Fixes: f6f9279f2b ("misc: fastrpc: Add Qualcomm fastrpc basic driver model")
Cc: stable <stable@kernel.org>
Signed-off-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Link: https://lore.kernel.org/r/20240108114833.20480-1-quic_ekangupt@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b4909252da ]
When building with Clang we encounter the following warning
(ARCH=hexagon + CONFIG_FRAME_WARN=0):
| ../drivers/misc/lkdtm/bugs.c:107:3: error: format specifies type
| 'unsigned long' but the argument has type 'int' [-Werror,-Wformat]
| REC_STACK_SIZE, recur_count);
| ^~~~~~~~~~~~~~
Cast REC_STACK_SIZE to `unsigned long` to match format specifier `%lu`
as well as maintain symmetry with `#define REC_STACK_SIZE
(_AC(CONFIG_FRAME_WARN, UL) / 2)`.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Reported-by: Nathan Chancellor <nathan@kernel.org>
Suggested-by: Nathan Chancellor <nathan@kernel.org>
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Fixes: 24cccab42c ("lkdtm/bugs: Adjust recursion test to avoid elision")
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220721215706.4153027-1-justinstitt@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee62360272 ]
Clang static analyzer complains that value stored to 'rets' is never
read.Let 'buf_len = -EOVERFLOW' to make sure we can return '-EOVERFLOW'.
Fixes: 8c8d964ce9 ("mei: move hbuf_depth from the mei device to the hw modules")
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20231120095523.178385-2-suhui@nfschina.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f06aee808 ]
mei_msg_hdr_init() return negative error code, rets should be
'PTR_ERR(mei_hdr)' rather than '-PTR_ERR(mei_hdr)'.
Fixes: 0cd7c01a60 ("mei: add support for mei extended header.")
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20231120095523.178385-1-suhui@nfschina.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
