Verify the old zone count has a valid value before using
it to compute slab summary entry offsets.
Signed-off-by: Matthew Sakai <msakai@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Verify that the loaded zone count is in the valid range
before using it as a loop iterator.
Signed-off-by: Matthew Sakai <msakai@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
The 'marvell,xenon-emmc' property used in some device trees of Armada 3720
based boards is not documented. Due to this dtbs_check throws warnings:
.../armada-3720-atlas-v5.dtb: mmc@d8000 (marvell,armada-3700-sdhci): Unevaluated properties are not allowed ('marvell,xenon-emmc' was unexpected)
.../armada-3720-espressobin-emmc.dtb: mmc@d8000 (marvell,armada-3700-sdhci): Unevaluated properties are not allowed ('marvell,xenon-emmc' was unexpected)
Apart from the warnings, 'git grep' says that the property is used in
device trees only:
$ git grep -n 'marvell,xenon-emmc'
arch/arm64/boot/dts/marvell/armada-3720-atlas-v5.dts:85: marvell,xenon-emmc;
arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi:81: marvell,xenon-emmc;
Although handling of the property was there in an early version of
the 'sdhci-xenon' driver during the initial submission [1], but that
part has been removed in later versions.
Drop the property from the affected device trees due to the reasons
mentioned above.
No functional changes intended, compile tested only.
Link: https://lore.kernel.org/r/0390e7a05b6163deabb545f93729ea615eeaaee2.1477911954.git-series.gregory.clement@free-electrons.com # [1]
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Commit fcaf733ca5 ("MAINTAINERS: Add Falcon DB") adds a new file entry
referring to non-existing files arch/arm/boot/dts/marvell/db-falcon*.
Checking with 'find . -name db-falcon*' and the files actually added with
the commit b3370479a5 ("arm64: dts: a7k: add COM Express boards"), which
was part of the same patch series, the files intended to refer to are
actually arch/arm64/boot/dts/marvell/db-falcon-carrier-a7k.dts and
arch/arm64/boot/dts/marvell/db-falcon-carrier.dtsi.
Note though that there is already a file entry for
arch/arm64/boot/dts/marvell/ in the ARM/Marvell Kirkwood and Armada SOC
support section. So, the added files were already covered by the
existing MAINTAINERS file and no further file entry is required at all.
Drop the unneeded file entry, essentially reverting the commit
fcaf733ca5 ("MAINTAINERS: Add Falcon DB").
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@redhat.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
On eDPU plus, which is an updated revision of eDPU which uses an external
MV88E6361 switch we are relying on U-Boot to detect the board, and then
enable and disable the required nodes for that revision.
However, it seems that I missed adding the required aliases for ethernet
controllers, and this worked as in OpenWrt we had added those locally.
Cc: stable@vger.kernel.org
Fixes: 660b8b2f39 ("arm64: dts: marvell: eDPU: add support for version with external switch")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
These .dtsi files are not included anywhere in the tree and can't be
tested.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Elad Nachman <enachman@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Documentation/devicetree/bindings/net/ethernet-controller.yaml
phy:
: #/properties/phy-handle
deprecated: true
New dts files should not be using deprecated properties.
What should be used is:
phy-handle:
: /schemas/types.yaml#/definitions/phandle
description:
Specifies a reference to a node representing a PHY device.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Elad Nachman <enachman@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
I was just informed that this product is discontinued (without being
ever released to the market). Pull the plug and let's not waste any more
maintainers time and revert commit 0f6eae86e6 ("dt-bindings: hwmon:
sl28cpld: add sa67mcu compatible").
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20260302122540.1377444-8-mwalle@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In one case the 0x is provided in the formatting string, while
the rest use # for that.
In a couple of more cases a decimal signed value specifier is used.
Amend them to use %#x when register is printed. Note, for the case,
when it's related to the read/write, use %x to be in align with
the similar messages in regmap core.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260302095847.2310066-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of the iterators may be defined inside the respective for-loop
reducing the scope and potential risk of their misuse. While at it,
align their types based on the type of the upper or lower limits.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260302095847.2310066-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The datasheet specifies, that the IRQ_B pin is pulled low when any
unmasked interrupt bit status is changed, and it is released high once
the application processor reads the INT1 register. As it specifies a
level-low behavior, it should not force a falling-edge interrupt.
Remove the IRQF_TRIGGER_FALLING to not force the falling-edge interrupt
and instead rely on the flag from the device tree.
Fixes: 0959b67063 ("regulator: pf9453: add PMIC PF9453 support")
Cc: stable@vger.kernel.org
Signed-off-by: Franz Schnyder <franz.schnyder@toradex.com>
Link: https://patch.msgid.link/20260218102518.238943-2-fra.schnyder@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Tegra238 requires different PLLA and PLLA_OUT0 clock rates compared to
other Tegra platforms. Add Tegra238 compatible string to the APE
tegra-audio-graph-card bindings.
Signed-off-by: Sheetal <sheetal@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260302085323.3139571-2-sheetal@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
getopt_long() processes short and long options independently.
RTLA, like the majority of applications, uses both short and long
variants for each logical option.
Since the val member of struct option holds the letter of the short
variant, the string of short options can be reconstructed from the
array of long options.
Add getopt_auto() to generate optstring from an array of long options,
eliminating the need to maintain separate short option strings.
Signed-off-by: Costa Shulyupin <costa.shul@redhat.com>
Reviewed-by: Wander Lairson Costa <wander@redhat.com>
Link: https://lore.kernel.org/r/20260108095011.2115719-1-costa.shul@redhat.com
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
Commit 70b0d6b0a1 ("tee: optee: Fix supplicant wait loop") made the
client wait as killable so it can be interrupted during shutdown or
after a supplicant crash. This changes the original lifetime expectations:
the client task can now terminate while the supplicant is still processing
its request.
If the client exits first it removes the request from its queue and
kfree()s it, while the request ID remains in supp->idr. A subsequent
lookup on the supplicant path then dereferences freed memory, leading to
a use-after-free.
Serialise access to the request with supp->mutex:
* Hold supp->mutex in optee_supp_recv() and optee_supp_send() while
looking up and touching the request.
* Let optee_supp_thrd_req() notice that the client has terminated and
signal optee_supp_send() accordingly.
With these changes the request cannot be freed while the supplicant still
has a reference, eliminating the race.
Fixes: 70b0d6b0a1 ("tee: optee: Fix supplicant wait loop")
Signed-off-by: Amirreza Zarrabi <amirreza.zarrabi@oss.qualcomm.com>
Tested-by: Ox Yeh <ox.yeh@mediatek.com>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Merge series from Stefan Binding <sbinding@opensource.cirrus.com>:
When the CS35L41 and CS35L45 drivers suspend, they are put into
hibernation, and the regmap goes into cache_only, but the firmware is
still running, and wm_adsp is not stopped. If userspace attempts to
read a firmware control, it will perform a regmap_raw_read() and this
will produce an error in the kernel log.
To prevent these spurious errors, add an apis into cs_dsp and wm_adsp
to allow wm_adsp to hibernate. In this hibernation mode, reads or
writes to the dsp controls would be rejected with -EPERM rather than
-EBUSY, and no error will be printed to the kernel log.
Merge series from Sander Vanheule <sander@svanheule.net>:
uni_player_parse_dt_audio_glue() allocates two regmap_field objects on
the device's regmap. However, error codes from these allocations are not
propagated correctly and the resources will leak on device removal.
These issues were found while looking for users of regmap_field_alloc(),
to assess the impact of adding a cleanup helper for regmap_field. It
appears this driver is the only (remaining) in-tree user of this
allocator. Since the resources are long-lived, it may as well switch to
devm_regmap_field_alloc().
As I don't have access to this hardware, these patches were only compile
tested on a UM build.
Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>:
Currently, we set a predefined codec component name in a DAI link. But
the codec name may contain an index which is not fixed. This series
suggest using partial match the codec name to fix the issue.
Two x86 platform drivers have unnecessary module_init() and module_exit()
functions that are empty or just print a message. Remove them.
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Link: https://patch.msgid.link/20260131020118.46171-1-enelsonmoore@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Simplify the initialization and cleanup flow for Versal Net DDRMC
controllers in the EDAC driver by carving out the single controller init
into a separate function which allows for a much better and more
readable error handling and unwinding.
[ bp:
- do the kzalloc allocations first
- "publish" the structures only after they've been initialized
properly so that you don't need to unwind unnecessarily when
it fails later
- remove_versalnet() is now trivial
]
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://patch.msgid.link/20251104093932.3838876-1-shubhrajyoti.datta@amd.com
The hardware PU/PD config of the pin after reset is to pull-up and on
Jaguar this will also keep the device in reset until the driver actually
enables the pin. So restore this boot pull-up config of the pin on Jaguar
instead of setting it to pull-none.
Suggested-by: Quentin Schulz <quentin.schulz@cherry.de>
Fixes: 0ec7e10963 ("arm64: dts: rockchip: add PCIe3 support on rk3588-jaguar")
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://patch.msgid.link/20260210080303.680403-5-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
While specific driver in the Linux-Kernel handles GPIOs gracefully without
matching pinctrl entries, this might not be true for other operating
systems. So having pinctrl entries makes the hardware-description
more complete.
The somewhat similar rk3588-jaguar board has a pinctrl entry already,
so also add one for rk3588-tiger.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Link: https://patch.msgid.link/20260210080303.680403-4-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Using a combination of fixed clock and gpio-gate clock works but does
not describe the actual hardware. Use the gated-fixed-clock binding
to describe this in a nicer way.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://patch.msgid.link/20260210080303.680403-3-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Using a combination of fixed clock and gpio-gate clock works but does
not describe the actual hardware. Use the gated-fixed-clock binding
to describe this in a nicer way.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://patch.msgid.link/20260210080303.680403-2-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The PineNote has a single cell 4000mAh battery which can be charged via
the rk817 PMIC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Co-developed-by: Maximilian Weigand <mweigand@mweigand.net>
Signed-off-by: Maximilian Weigand <mweigand@mweigand.net>
Signed-off-by: Diederik de Haas <diederik@cknow-tech.com>
Link: https://patch.msgid.link/20260224170531.516392-1-diederik@cknow-tech.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Instead of testing import_attach for imported GEM buffers, invoke
drm_gem_is_imported() to do the test. The test itself does not change.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Steven Price <steven.price@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patch.msgid.link/20260227133113.235940-8-tzimmermann@suse.de
Instead of testing import_attach for imported GEM buffers, invoke
drm_gem_is_imported() to do the test. The test itself does not change.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Steven Price <steven.price@arm.com>
Cc: "Adrián Larumbe" <adrian.larumbe@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patch.msgid.link/20260227133113.235940-7-tzimmermann@suse.de
Add support for the Rockchip RV1103B Clock and Reset Unit (CRU).
The RV1103B CRU is compatible with the existing RV1126B binding.
Add the compatible string to the schema and introduce the
corresponding clock ID definitions.
Signed-off-by: Fabio Estevam <festevam@nabladev.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260210022620.172570-1-festevam@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the clock and reset tree definitions for the RV1103B SoC.
Based on the 5.10 Rockchip vendor kernel driver.
Signed-off-by: Fabio Estevam <festevam@nabladev.com>
Link: https://patch.msgid.link/20260210022620.172570-2-festevam@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In rk3576.dtsi, sdmmc0_pwren is configured as part of the sdmmc pinctrl.
However, on the rk3576 evb2 board, sdmmc0_pwren is used as the regulator
for vmmc-supply. Therefore, we need to reassign the sdmmc pinctrl and
remove sdmmc0_pwren to avoid conflicts.
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 86a82f7a7e ("arm64: dts: rockchip: Add rk3576 evb2 board")
Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Link: https://patch.msgid.link/20260226102052.63-1-kernel@airkyi.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Introduce the Zena CSS Fixed Virtual Platform (FVP) dts. This is
currently the only Zena CSS variant, however the common definitions are
included in a common dtsi for extensibility.
Signed-off-by: Debbie Horsfall <debbie.horsfall@arm.com>
Message-Id: <20260212-zena-css-v2-2-d33ea23cb9c2@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@kernel.org>
Provide individual LPAE and non-LPAE definitions for both these
functions, rather than having ifdefs inside the function body. This
places the functions closer to their associated definitions.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
The FSR's fault status bits depend on whether LPAE is enabled. Rather
than always exposing both LPAE and non-LPAE to all code, move them
inside the ifdef blocks dependent on LPAE to restrict their visibility.
No code other than fsr_fs() makes use of these.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Modernise the fault status field definitions by using BIT() and
GENMASK().
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
is_permission_fault() and is_translation_fault() are both conditional
on the FSR encodings, which are dependent on LPAE. We define the
constants in fault.h. Move these inline functions to fault.h to be
near the FSR definitions.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Make checkpatch happy. This helps when checkpatch is set up as an
automatic linter.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260214025246.2095239-4-dmitry.torokhov@gmail.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Extend platform_device_info structure with an optional pointer to a
software node to be used as a secondary firmware node for the device
being created. If software node has not been registered yet it will be
automatically registered.
This reduces boilerplate needed when switching legacy board code to
static device properties/GPIO references.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260214025246.2095239-3-dmitry.torokhov@gmail.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Add kernel documentation for struct platform_device_info and its
individual members. While at it remove an extra indent level from the
structure definition.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260214025246.2095239-2-dmitry.torokhov@gmail.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
This triggers a WARN_ON in ieee80211_hw_conf_init and isn't the expected
behavior from the driver - other drivers default to 0 too.
Fixes: 0a44dfc070 ("wifi: mac80211: simplify non-chanctx drivers")
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Link: https://patch.msgid.link/20260221-rsi-config-ret-v1-1-9a8f805e2f31@puri.sm
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split the vmalloc() lazy-page table population from
do_translation_fault() into a new vmalloc_fault() function.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
__do_user_fault() may be called from fault handling paths where the
interrupts are enabled or disabled. E.g. do_page_fault() calls this
with interrupts enabled, whereas do_sect_fault()->do_bad_area()
will call this with interrupts disabled. Since this is a userspace
fault, we know that interrupts were enabled in the parent context,
so call local_irq_enable() here to give a consistent interrupt state.
This is necessary for force_sig_info() when PREEMPT_RT is enabled.
Reported-by: Yadi.hu <yadi.hu@windriver.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Fix incorrect model string in Devicetree for BPI-R4-Pro.
Fixes: f397471a6a ("arm64: dts: mediatek: mt7988: Add devicetree for BananaPi R4 Pro")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Commits bf4afc53b7 ("Convert 'alloc_obj' family to use the new default
GFP_KERNEL argument") and 69050f8d6d ("treewide: Replace kmalloc with
kmalloc_obj for non-scalar types") updated various k[z|m|c]alloc calls to their
k[z|m]alloc_obj counterparts.
This commit finalizes that transition within the RDMA subsystem.
Link: https://patch.msgid.link/20260226-complete-alloc-conversion-v1-1-ebf1df1c2518@nvidia.com
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Before the MIPI DSI clock source can be configured, the target divide
ratio needs to be set.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Fixes: 5a4326f2e3 ("clk: renesas: rzg2l: Remove DSI clock rate restrictions")
Link: https://patch.msgid.link/20260227015216.2721504-1-chris.brandt@renesas.com
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Currently key installation is only supported for netdev. For NAN,
support most key operations (except setting default data key) on
wdevs instead of netdevs, and adjust all the APIs and tracing to
match.
Since nothing currently sets NL80211_EXT_FEATURE_SECURE_NAN, this
doesn't change anything (P2P Device already isn't allowed.)
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260107150057.69a0cfad95fa.I00efdf3b2c11efab82ef6ece9f393382bcf33ba8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Correct an enum name in a kernel-doc comment to avoid kernel-doc
warnings:
Warning: include/linux/pinctrl/pinconf-generic.h:161 Enum value
'PIN_CONFIG_SKEW_DELAY_OUTPUT_PS' not described in enum 'pin_config_param'
Warning: include/linux/pinctrl/pinconf-generic.h:161 Excess enum value
'@PIN_CONFIG_SKEW_DELAY_OUPUT_PS' description in 'pin_config_param'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>