NetDrvEpEnv picks a single IP version at init time, preferring IPv6 when
both are configured.
Add NetDrvEpEnv.set_ipver() to reselect the IP version and recompute the
derived address fields.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Nimrod Oren <noren@nvidia.com>
Link: https://patch.msgid.link/20260702062348.2123960-2-noren@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The snd-aloop driver currently defaults to using the system jiffies
timer (struct timer_list). On systems configured with a low timer
interrupt frequency (e.g., CONFIG_HZ=250), the jiffies resolution
(4ms per tick) is insufficient for precise audio timing. For
example, a 10ms audio period requires 2.5 jiffies ticks, causing
timing jitter that leads to capture underruns.
Introduce "hrtimer" as a supported timer_source option. When
timer_source="hrtimer" is set, aloop uses high-resolution timers
(hrtimer) to drive period updates. This provides nanosecond-level
accuracy regardless of CONFIG_HZ and operates independently of other
hardware audio cards.
Signed-off-by: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Link: https://patch.msgid.link/20260705125941.1203871-1-yuhsuan@chromium.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, configuring a VF MAC address via the PF (e.g., 'ip link
set <pf> vf 0 mac <mac>') blindly attempts to install a DMAC-based
hardware filter. However, the hardware parser profile might not
support DMAC extraction.
Check if the hardware parsing profile supports DMAC extraction
before adding the filter. Additionally, emit a warning message
to inform the operator if the MAC filter installation fails due
to missing DMAC extraction support. Update config->mac only
after hardware programming succeeds in otx2_set_vf_mac().
Fixes: f0c2982aaf ("octeontx2-pf: Add support for SR-IOV management functions")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Nitin Shetty J <nshettyj@marvell.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20260702033451.2969880-1-nshettyj@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
CAKE accepts signed overhead values and stores them in an s16, but the
adjusted packet length calculation uses unsigned arithmetic. A negative
effective length can therefore wrap to a large value.
Such configurations make rate accounting depend on integer wraparound
rather than on the packet size userspace intended to model. A static
netlink lower bound is not enough because packets reaching CAKE can be
smaller than any reasonable manual-overhead allowance.
Fold the signed overhead adjustment into the existing datapath MPU clamp
so negative adjusted lengths are clamped before link-layer framing
adjustments.
Fixes: a729b7f0bd ("sch_cake: Add overhead compensation support to the rate shaper")
Assisted-by: Codex:gpt-5.5-cyber-preview
Signed-off-by: Samuel Moelius <sam.moelius@trailofbits.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20260702000758.297407.e5c888d9d99d.cake-overhead-underflow@trailofbits.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tariq Toukan says:
====================
devlink: extend phys_port_name controller prefix to non-external ports
This series by Moshe includes the controller number in phys_port_name
for non-external ports with a non-zero controller, and updates the mlx5
driver to mark satellite PFs as non-external.
The controller prefix (c) in phys_port_name was previously only included
for ports marked as external. However, newer devices can have multiple
controllers within the DPU itself, even within a single host
environment. For example, a SmartNIC may have additional local PCI
physical functions that are managed by the eswitch but are not on an
external host. These ports use a non-zero controller number to
distinguish them from the eswitch manager's own functions, while the
external flag remains unset.
Patch 1 updates the devlink core to include the controller prefix in
phys_port_name for any non-zero controller, regardless of the external
flag. Documentation and kdoc are updated accordingly.
Patch 2 updates the mlx5 driver to set satellite PF devlink ports as
non-external, since they are local to the DPU. It also distinguishes
satellite PF SFs from host PF SFs when setting the external attribute.
====================
Link: https://patch.msgid.link/20260702111726.816985-1-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Satellite PFs are local to the DPU and are not on an external host.
Set their devlink port external attribute to false to reflect this.
For satellite PF SFs, distinguish them from host PF SFs by comparing
the SF controller number against the host PF controller
(hpf_host_number + 1). Only SFs whose controller matches the host PF
are marked external, since their PF resides on an external host.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Shay Drori <shayd@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260702111726.816985-3-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The controller prefix (c<N>) in phys_port_name is currently restricted
to external host controllers. This layout sufficed when DPUs only had a
single local controller and one or more external host controllers.
However, newer devices can have multiple controllers within the DPU
itself, even within a single host environment. To support these
topologies, allow drivers to report the controller number regardless of
the "external" flag status. Any non-zero controller number will now be
explicitly reported, even for single-host or local DPU controllers.
Existing ports with controller=0 are unaffected.
Update documentation and kdoc to clarify that a non-zero controller
number does not require the external flag to be set.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260702111726.816985-2-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add a new driver for Sony imx471 camera sensor. It is based on
Jimmy Su <jimmy.su@intel.com> implementation and the driver can be found
in the following URL.
https://github.com/intel/ipu6-drivers/commits/master/drivers/media/i2c/imx471.c
This sensor can be found on Lenovo X1 Carbon G14, X9-14 and X9-15 laptops
and it is a part of IPU7 solution. The driver was tested on Lenovo X1
Carbon G14, X9-14 and X9-15 laptops.
Signed-off-by: Kate Hsuan <hpa@redhat.com>
Tested-by: computman <anis@talbi.fr>
Reviewed-by: Tarang Raval <tarang.raval@siliconsignals.io>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Update the con_id for the Sony IMX471 sensor to "vana" to serve as the
power enable. Additionally, the HID values SONY471A and TBE20A0, both
associated with the IMX471 image sensor, have been identified on Lenovo
laptops.
Signed-off-by: Kate Hsuan <hpa@redhat.com>
Reviewed-by: Tarang Raval <tarang.raval@siliconsignals.io>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The HID for Sony IMX471 is TBE20A0 on Lenovo X1 Carbon G14.
Signed-off-by: Kate Hsuan <hpa@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The Lenovo X9 has an upside-down-mounted Sony IMX471 sensor so the image
was displayed upside-down. Add the DMI information of Lenovo X9 to
resolve the issue.
Signed-off-by: Kate Hsuan <hpa@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
When fuse enables large folios, a large folio will be backed by
iomap_folio_state that keeps track of uptodate and dirty state in an
internal bitmap.
Fuse writethrough and notify store paths currently set folio uptodate
state with folio_mark_uptodate(), which touches only the folio-level
flag, but on an iomap-backed folio, that leaves the uptodate bitmap out
of sync.
Use the iomap_folio_mark_uptodate() helper to update both the folio
uptodate state and the iomap uptodate bitmap.
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Add an exported helper iomap_folio_mark_uptodate() to mark a folio as
uptodate and update its uptodate bitmap if the folio has iomap state
data attached.
This is needed because there are some filesystems (eg fuse) that have
paths outside of conventional iomap calls that need to mark a folio as
uptodate (eg writing server-pushed data directly into the page cache)
and need the iomap-internal uptodate bitmap to be in sync with the
uptodate state of the folio.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
In the writethrough path (fuse_send_write_pages()), if the write to the
server failed or was a short write, the uptodate flag on the folios are
cleared.
As explained by Matthew in [1], this is dangerous because the folio may
be mapped into userspace. The mm code has the invariant that a
non-uptodate folio must never be visible to userspace (to avoid
potentially leaking confidental information to userspace) and has checks
in place for this that if violated can bring down the whole machine.
Practically speaking, the effect of this change for the fuse
writethrough error path is that if an application does a write and then
the server fails to persist the data or only services a short write, the
page cache folio keeps the data the application wrote instead of being
reverted to the server's contents on the next read. The failure is still
reported to the application synchronously through the short count /
error return of the write() syscall. Folios that were only partially
written are unaffected since they were never marked uptodate in the
first place (fuse_fill_write_page() only marks a folio as uptodate if
the whole folio was written to).
[1] https://lore.kernel.org/linux-fsdevel/ajtPMgO65FA1TXhi@casper.infradead.org/
Suggested-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Bastien Curutchet says:
====================
net: dsa: microchip: move non-common function out of ksz_common.c
This series continues the rework of the KSZ driver initiated by three
previous series (see [1], [2] & [3]).
The KSZ driver handles more than 20 switches split in several families.
This was previously handled through a common set of dsa_switch_ops
operations that used device-specific ksz_dev_ops callbacks. The three
previous series have split this common struct dsa_switch_ops into 5
to connect the ksz_dev_ops's implentations directly to the new
dsa_swicth ops.
This series continues in the same vein and moves out of ksz_common.c all
the functions that aren't truly common to all the families.
On top of this on-going rework I added PTP and periodic output support for
the KSZ8463 (which was my first goal). There are still more than 13 patches
left for all this so this series will be followed by two others and if you
want to see the full picture we can check my github ([4]).
FYI, I only have a KSZ8463 so, unfortunately, I can't test other switches.
The next series is going to add PTP support for the KSZ8463. The final one
will add periodic output support for the KSZ8463.
[1]: https://lore.kernel.org/r/20260505-clean-ksz-driver-v1-0-05d70fa42461@bootlin.com
[2]: https://lore.kernel.org/r/20260521-clean-ksz-2nd-series-v3-0-75c38971c19a@bootlin.com
[3]: https://lore.kernel.org/r/20260608-clean-ksz-3rd-v2-0-6e61b7be23c4@bootlin.com
[4]: https://github.com/bastien-curutchet/linux/tree/ksz_rework
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
====================
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-0-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The drive strength configuration is done during the setup of all
switches through a common function that then has specific behavior
depending on the switch identity.
Split the common configuration in two functions: one is dedicated to the
KSZ8 family, the other is dedicated to the KSZ9477 family.
Remove the drive strength configuration from the lan937x_setup since
the LAN937x family doesn't support it.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-10-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ksz9477_drive_strength_write() isn't used for the KSZ9477-family only.
It's also used for the KSZ87xx chip variants. This function name is
misleading.
Rename it ksz_drive_strength_write().
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-9-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ksz9477_set_default_prio_queue_mapping() dictates a KSZ9477-specific
behavior but is defined in the common section of the code.
Move its definition to the KSZ9477-specific area.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-8-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The setup of QDISC_ETS isn't the same for the KSZ8 switches than for
the other switches. It leads to is_ksz8() branches in the common code.
Move the KSZ8-specific portions into ksz8.c by creating two setup_tc()
functions, one dedicated to the KSZ87xx family that only handles the
TC_SETUP_QDISC_CBS case, one for the rest of the KSZ8 that handles both
TC_SETUP_QDISC_CBS and TC_SETUP_QDISC_ETS cases.
It remains some is_kszXXXX() branches because inside the ksz88xx family,
only the ksz88x3 switches support QDISC_ETS.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-7-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The KSZ9477 PHY errata is handled from the common ksz_r_mib_stat64().
This errata clearly belongs to the KSZ9477 family so it should be handled
from the ksz9477-specific portion of the driver.
Create a ksz9477-specific r_mib_stat64() implementation that handles
this errata.
Remove the errata handling from the common ksz_r_mib_stat64().
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-6-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ksz_get_gbit() and ksz_get_xmii() are defined in the ksz_common while
they are only used by the ksz9477 driver.
Move their definition into ksz9477.c
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-5-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ksz88xx_r_mib_stats64() is defined in ksz_common while it's clearly
ksz88xx-specific.
Move its definition in ksz8.c
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-4-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ksz_is_port_mac_global_usable() is exposed in ksz_common.h while it's
only used internally.
Make ksz_is_port_mac_global_usable() static.
Move its definition above its first call.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-3-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ksz_max_mtu() is a bit cluttered. It would be good for developers and
reviewers if they didn't need to look at a common function for hardware
they likely don't have, and which is vastly different, when they are
interested in only a specific chip.
Benefit from the fact that all families listed here have their own
dsa_switch_ops, and provide separate implementations for the
port_max_mtu() method.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-2-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Even among the ksz8 family, there are big differences in the MTU change
procedure between KSZ87xx and KSZ88xx (KSZ8463 is like KSZ88xx here).
Since we have 3 separate dsa_switch_ops for what constitutes "KSZ8", we
can split those procedures into separate functions.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-1-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Mike Rapoport says:
====================
drivers/net/ethernet: replace __get_free_pages() with kmalloc()
This is a (small) part of larger work of replacing page allocator calls
with kmalloc.
My initial intention a few month ago was to remove ugly casts [1], but then
willy pointed out that Linus objected to something like this [2] and it
looks like more than a decade old technical debt.
Largely, anything that doesn't need struct page (or a memdesc in the
future) should just use kmalloc() or kvmalloc() to allocate memory.
kmalloc() guarantees alignment, physical contiguity and working
virt_to_phys() and beside nicer API that returns void * on alloc and
doesn't require to know the allocation size on free, kmalloc() provides
better debugging capabilities than page allocator.
Another thing is that touching these allocation sites gives the reviewers
opportunity to see if a PAGE_SIZE buffer is actually needed or maybe
another size is appropriate.
For larger allocations that don't need physically contiguous memory
kvmalloc() can be a better option that __get_free_pages() because under
memory pressure it's is easier to allocate several order-0 pages than a
physically contiguous chunk with the same number of pages.
And last, but not least, removing needless calls to page allocator should
help with memdesc (aka project folio) conversion. There will be way less
places to audit to see if the user was actually using struct page.
Also in git:
https://git.kernel.org/pub/scm/linux/kernel/git/rppt/linux.git gfp-to-kmalloc/drivers-net-ethernet
[1] https://lore.kernel.org/all/20251018093002.3660549-1-rppt@kernel.org/
[2] https://lore.kernel.org/all/CA+55aFwp4iy4rtX2gE2WjBGFL=NxMVnoFeHqYa2j1dYOMMGqxg@mail.gmail.com/
====================
Link: https://patch.msgid.link/20260701-b4-drivers-ethernet-v1-0-58776615db6e@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
efx_mcdi_init() allocates a logging buffer for MCDI firmware
communication diagnostics.
This buffer can be allocated with kmalloc() as there's nothing special
about it to go directly to the page allocator.
kmalloc() provides a better API that does not require ugly casts and
kfree() does not need to know the size of the freed object.
Performance difference between kmalloc() and __get_free_pages() is not
measurable as both allocators take an object/page from a per-CPU list for
fast path allocations.
For the slow path the performance is anyway determined by the amount of
reclaim involved rather than by what allocator is used.
Replace use of __get_free_page() with kmalloc() and free_page() with
kfree().
Link: https://lore.kernel.org/all/635405e4-9423-4a25-a6e7-e03c8ea0bcbe@redhat.com
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20260701-b4-drivers-ethernet-v1-4-58776615db6e@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
efx_siena_mcdi_init() allocates a logging buffer for MCDI firmware
communication diagnostics.
This buffer can be allocated with kmalloc() as there's nothing special
about it to go directly to the page allocator.
kmalloc() provides a better API that does not require ugly casts and
kfree() does not need to know the size of the freed object.
Performance difference between kmalloc() and __get_free_pages() is not
measurable as both allocators take an object/page from a per-CPU list for
fast path allocations.
For the slow path the performance is anyway determined by the amount of
reclaim involved rather than by what allocator is used.
Replace use of __get_free_page() with kmalloc() and free_page() with
kfree().
Link: https://lore.kernel.org/all/635405e4-9423-4a25-a6e7-e03c8ea0bcbe@redhat.com
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20260701-b4-drivers-ethernet-v1-3-58776615db6e@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ice_gnss_read() uses get_zeroed_page() to allocate a staging buffer for
reading GNSS module data via I2C bus.
This buffer can be allocated with kmalloc() as there's nothing special
about it to go directly to the page allocator.
kmalloc() provides a better API that does not require ugly casts and
kfree() does not need to know the size of the freed object.
Performance difference between kmalloc() and __get_free_pages() is not
measurable as both allocators take an object/page from a per-CPU list for
fast path allocations.
For the slow path the performance is anyway determined by the amount of
reclaim involved rather than by what allocator is used.
Replace use of get_zeroed_page() with kzalloc() and free_page() with
kfree().
Link: https://lore.kernel.org/all/635405e4-9423-4a25-a6e7-e03c8ea0bcbe@redhat.com
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Link: https://patch.msgid.link/20260701-b4-drivers-ethernet-v1-2-58776615db6e@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
bnx2x_mcast_enqueue_cmd() allocates memory for mac filtering list using
__get_free_pages().
This memory can be allocated with kzalloc() as there's nothing special
about it to go directly to the page allocator.
kmalloc() provides a better API that does not require ugly casts and
kfree() does not need to know the size of the freed object.
Performance difference between kmalloc() and __get_free_pages() is not
measurable as both allocators take an object/page from a per-CPU list for
fast path allocations.
For the slow path the performance is anyway determined by the amount of
reclaim involved rather than by what allocator is used.
Replace use of __get_free_page() with kzalloc() and free_page() with
kfree().
Link: https://lore.kernel.org/all/635405e4-9423-4a25-a6e7-e03c8ea0bcbe@redhat.com
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Link: https://patch.msgid.link/20260701-b4-drivers-ethernet-v1-1-58776615db6e@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
rtla started to only link parts of the tools library. It now misses the
ctype information used by all the related string operations. Just add
another single file to make it build again.
Signed-off-by: Bastian Blank <waldi@debian.org>
Fixes: 48209d763c ("rtla: Add libsubcmd dependency")
Link: https://lore.kernel.org/r/ako2S4mzIqWwYuas@steamhammer.waldi.eu.org
[ remove duplicated spaces in commit message ]
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
Background:
==========
Currently lockdep does not print out the held locks of non-current
tasks that are running on some other CPU, due to the fact that
the held locks array is in flux and may be unreliable to print.
Syzkaller on the other hand found it that the analysis of locking
bugs is easier if we print this information too, because the
more locking information the merrier. In particular races are
bound to have multiple tasks running on different CPUs, and
the exclusion of their held locks information is unnecessarily
limiting.
So while it's still true that printing out their held locks
array is racy, it's not as bad as it seems.
There's 16 internal callers to lockdep_print_held_locks():
- 14 callers call it with the current task, which should be
safe out of box.
- 1 caller, debug_show_all_locks(), calls it with RCU held,
which should guarantee that 'p' cannot go away under us.
- 1 caller, debug_show_held_locks(), exposes the internal API
with the constraint that it should only be called by drivers
or platform code if the task isn't actively running - we can
assume that if it nevertheless does, it will be Their Problem™.
As for held locks being changed from under debug_show_held_locks(),
while the task cannot go away, so the held-locks array itself is
safe (although potentially non-stable), AFAICS the worst-case race
can be garbage printed out by print_lock(), not any actual crashes.
In particular:
unsigned int class_idx = hlock->class_idx;
may be stale (belong to a lock that already got released on another
CPU), but it should still be a valid class index bound by
MAX_LOCKDEP_KEYS, and thus the lock_classes_in_use bitmap use
should be safe.
The other two accesses are ::acquire_ip and ::instance:
printk(KERN_CONT "%px", hlock->instance);
print_lock_name(hlock, lock);
printk(KERN_CONT ", at: %pS\n", (void *)hlock->acquire_ip);
But both are printed out as pointers, so no risk of dereference
of a dangling pointer. We may print a garbage pointer.
Also note that the check itself doesn't protect debug_show_held_locks()
from printing garbage, as there's nothing that keeps a task from
becoming runnable a nanosecond after we've run the task_is_running()
check. In fact I'd argue that it's better to make this function
*more* racy, for the simple robustness reason that we absolutely
do not want it to crash even in the racy case.
TL;DR: it should be fine to print the held locks of running
tasks too, as long as we print out the information as well
that a task is running, so that users are aware of any
racy output.
Implementation:
==============
Implement that change.
Also re-flow the function and streamline the printout into
a single statement for all cases, which changes
the 'no locks held by' / '%d lock[s] held by' phrasing that had a
dependency on English spelling of plurals, to a uniform:
locks held by bash/1234: %d
Which spells correctly for 0, 1 and higher values, and should also
be easier to parse both for humans and for scripts.
Finally, print out the last CPU a task has ran on. This is very
useful information for races and for locking bugs in particular.
This basically extends the 'on CPU#%d' message we print for
running tasks to all tasks we print.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Suggested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Boqun Feng <boqun@kernel.org>
Cc: Gary Guo <gary@garyguo.net>
Cc: Mark Brown <broonie@kernel.org>
Cc: Theodore Tso <tytso@mit.edu>
Cc: Miguel Ojeda <ojeda@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Waiman Long <longman@redhat.com>
Link: https://patch.msgid.link/akoeSIQGwqd9cZwd@gmail.com
rmnet_get_endpoint() is shared by packet receive paths and
RTNL-protected control paths. The receive paths already run under RCU/BH
context through the RX handler, while the control paths reach
rmnet_get_endpoint() after obtaining the rmnet port with
rmnet_get_port_rtnl().
The helper walks port->muxed_ep[] with hlist_for_each_entry_rcu(). Pass
lockdep_rtnl_is_held() as the non-RCU protection condition so
CONFIG_PROVE_RCU_LIST can see the RTNL-protected control-path calls
while preserving the existing RCU-reader behavior for data paths.
This was found by our static analysis tool and then manually reviewed
against the current tree. The dynamic triage evidence is a
target-matched CONFIG_PROVE_RCU_LIST warning; the change is limited
to documenting the existing protection contract.
This is a lockdep annotation cleanup. It does not change endpoint
lifetime or hash updates.
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Reviewed-by: Subash Abhinov Kasiviswanathan <subash.a.kasiviswanathan@oss.qualcomm.com>
Link: https://patch.msgid.link/20260701124017.3205729-1-runyu.xiao@seu.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
multi_lrc_create_parent() returns ERR_PTR(0) when there are not enough
engines in the class to create a parallel context. ERR_PTR(0) evaluates
to NULL, and the only caller already treats NULL as the non-error
"not enough engines" case.
Return NULL directly to make the non-error path explicit.
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
Link: https://lore.kernel.org/r/20260706071412.559909-1-lilinmao@kylinos.cn
Correct spaces or mix of tabs+spaces into proper tab-indented lines.
No functional impact (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add a matching sysctl to go with CONFIG_SYSCALL_USER_DISPATCH.
kernel.syscall_user_dispatch (default 1 - allow) controls whether
userspace may arm syscall user dispatch (both via prctl and ptrace).
Disarming is always permitted - same semantics as comparable knobs.
Disabling while a task has armed syscall user dispatch does not
cause it to become inactive - instead it remains active until the
user attempts to disable/re-enable via prctl or ptrace. On the
next attempt to re-enable, the prctl/ptrace call fails gracefully.
The alternative would cause programs translating non-linux syscalls
to interpret those syscalls as linux syscalls, resulting in undefined
userland behavior.
Signed-off-by: Gregory Price <gourry@gourry.net>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260706140020.873735-3-gourry@gourry.net
Syscall User Dispatch is presently built under CONFIG_GENERIC_SYSCALL and
cannot be disabled independently.
Add CONFIG_SYSCALL_USER_DISPATCH to make it an optional feature.
Signed-off-by: Gregory Price <gourry@gourry.net>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260706140020.873735-2-gourry@gourry.net
The GTP PDP lookup helpers are shared by RCU-protected data and report
paths and RTNL-protected control paths such as gtp_genl_new_pdp(). The
helpers walk RCU hlists, but they do not currently pass the RTNL
condition for the control-path lookups.
Pass lockdep_rtnl_is_held() to the PDP hlist iterators. Existing
RCU-reader callers remain valid because the RCU-list macros also accept
an active RCU read-side section; the added condition only documents the
non-RCU protection already used by RTNL control paths.
This was found by our static analysis tool and then manually reviewed
against the current tree. The dynamic triage evidence is a
target-matched CONFIG_PROVE_RCU_LIST warning; the change is limited
to documenting the existing protection contract.
This is a lockdep annotation cleanup. It does not change PDP lifetime or
hash updates.
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260701123925.3193089-1-runyu.xiao@seu.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently each build with resolve_btfids enabled unnecessarily prints
the line 'INSTALL libsubcmd_headers' from libsubcmd.
Use the libcmd headers from source tree instead, without installation.
The same was done for objtool in commit ac99992677 ("objtool: Include
libsubcmd headers directly from source tree"), albeit for a different
reason.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Tested-by: Ihor Solodrai <ihor.solodrai@linux.dev>
Link: https://patch.msgid.link/20260702-libsubcmd-spam-v1-1-300ec142a62f@linutronix.de
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
REGMAP_MMIO is a hidden (non-user-visible) tristate symbol. Using
depends on it is incorrect because there is no way for the user to
enable it directly. Change to select, which is the convention used
by every other driver in the tree that needs REGMAP_MMIO.
Fixes: 8057cbb833 ("net: mdio: mscc-miim: Add depend of REGMAP_MMIO on MDIO_MSCC_MIIM")
Assisted-by: opencode:big-pickle
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260702032653.1580616-1-rosenp@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add test_trunc exercising the OVS_ACTION_ATTR_TRUNC action. The test
verifies truncation limits in four steps: reject trunc(1) and
trunc(13) which are below ETH_HLEN, confirm normal forwarding works,
apply trunc(14) which truncates packets to the Ethernet header and
verify ping fails, then restore normal forwarding and verify recovery.
The kernel requires max_len >= ETH_HLEN (14 bytes). trunc(14) sets
OVS_CB(skb)->cutlen so pskb_trim strips the IP payload at output
time; the receiver drops the runt frame and no echo reply is
generated.
Signed-off-by: Minxi Hou <houminxi@gmail.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20260702074926.1174810-1-houminxi@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit c7f92042d3 ("selftests: gpio: Add gpio-cdev-uaf tests") added
the gpio-cdev-uaf binary to TEST_GEN_PROGS_EXTENDED but never added it
to .gitignore. Building it with:
make -C tools/testing/selftests/gpio TARGETS=gpio
leaves gpio-cdev-uaf as an untracked file.
Fixes: c7f92042d3 ("selftests: gpio: Add gpio-cdev-uaf tests")
Signed-off-by: Cihan Karadag <cihan.cihan@gmail.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://patch.msgid.link/20260707235707.1349969-1-cihan.cihan@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Add a TCP congestion-control struct_ops load test for a write through a
BTF pointer produced by bpf_rdonly_cast().
The test expects the verifier to reject the program before the TCP CA
btf_struct_access callback can whitelist the tcp_sock field write.
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Reviewed-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
check_ptr_to_btf_access() lets program-type btf_struct_access callbacks
validate writes before the default BTF access path rejects non-read
accesses. That bypasses the read-only policy for untrusted BTF pointers
created by helpers such as bpf_rdonly_cast().
Reject non-read accesses through PTR_UNTRUSTED BTF pointers at the
common entry point, before the callback branch to handle all cases.
Fixes: 282de143ea ("bpf: Introduce allocated objects support")
Signed-off-by: Nicholas Dudar <main.kalliope@gmail.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Reviewed-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
RISCV_HWPROBE_EXT_ZICFISS and RISCV_HWPROBE_EXT_ZICFILP are defined in
the hwprobe uAPI but are not documented in
Documentation/arch/riscv/hwprobe.rst. Add documentation for them.
Link: 302a2d45c2
Reviewed-by: Andrew Jones <andrew.jones@oss.qualcomm.com>
Signed-off-by: Guodong Xu <docular.xu@gmail.com>
Link: https://patch.msgid.link/20260701-rva23u64-hwprobe-v2-v5-3-2c61f94a695a@gmail.com
Signed-off-by: Paul Walmsley <pjw@kernel.org>
A handful of vendor-extension entries indent continuation lines with a
tab character, while the rest of hwprobe.rst uses spaces. In addition,
many list items align their continuation lines under the 'm' of
':c:macro:' (column 7) rather than under the item text (column 4), so
the file mixes several indentation styles.
Replace the tabs with spaces and align every list item's continuation
lines under the item text, giving the whole file one consistent style.
Whitespace-only change, no functional change.
[Guodong: extend from tabs->spaces to normalizing all continuation-line
indentation across the file]
Signed-off-by: Andrew Jones <andrew.jones@oss.qualcomm.com>
Signed-off-by: Guodong Xu <docular.xu@gmail.com>
Link: https://patch.msgid.link/20260701-rva23u64-hwprobe-v2-v5-2-2c61f94a695a@gmail.com
Signed-off-by: Paul Walmsley <pjw@kernel.org>
The multi-letter extension enum is documented as being sorted
alphanumerically (see the "multi-letter extensions, sorted
alphanumerically" comment), but several Z entries have drifted out of
order.
Reorder the affected entries so the multi-letter Z list is sorted
alphanumerically again.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Guodong Xu <docular.xu@gmail.com>
Link: https://patch.msgid.link/20260701-rva23u64-hwprobe-v2-v5-1-2c61f94a695a@gmail.com
Signed-off-by: Paul Walmsley <pjw@kernel.org>
