During the v3 firmware download the controller sends a v3_data_req with a
32 bit offset and a 16 bit len. nxp_recv_fw_req_v3() checks only the lower
bound of the offset and then sends firmware from that offset.
nxpdev->fw_dnld_v3_offset = offset - nxpdev->fw_v3_offset_correction;
serdev_device_write_buf(nxpdev->serdev, nxpdev->fw->data +
nxpdev->fw_dnld_v3_offset, len);
Nothing checks that fw_dnld_v3_offset + len stays within nxpdev->fw->size,
so a controller that asks for an offset or length past the firmware image
makes the driver read past the end of nxpdev->fw->data and send that
memory back over UART.
nxp_recv_fw_req_v1() already bounds the same write. Add the equivalent
check to the v3 path, reject the request when it falls outside the firmware
image, and zero len on the error path so the fw_v3_prev_sent bookkeeping at
free_skb stays consistent.
Fixes: 689ca16e52 ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Suggested-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Maoyi Xie <maoyixie.tju@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
l2cap_get_conf_opt() derives the option length from the
attacker-controlled opt->len field and immediately dereferences
opt->val (as u8, get_unaligned_le16() or get_unaligned_le32(), or a
raw pointer for the default case) before any caller has confirmed
that opt->len bytes are present in the buffer. The callers
(l2cap_parse_conf_req(), l2cap_parse_conf_rsp() and
l2cap_conf_rfc_get()) only detect a malformed option afterwards, once
the running length has gone negative, by which point the
out-of-bounds read has already executed.
An existing post-hoc length check keeps the garbage value from being
consumed, so this is not a data leak in the current control flow. It
is still a validate-after-use ordering bug: up to 4 bytes are read
past the end of the buffer before it is known to contain them, and it
is fragile to future changes in the callers.
Fix it at the source. Pass the end of the buffer into
l2cap_get_conf_opt() and refuse to touch opt->val unless the full
option (header + value) fits. Each caller computes an end pointer
once before the loop and checks the return value directly instead of
inferring the error from a negative length.
Fixes: 7c9cbd0b5e ("Bluetooth: Verify that l2cap_get_conf_opt provides large enough buffer")
Cc: stable@vger.kernel.org
Signed-off-by: Muhammad Bilal <meatuni001@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
l2cap_conn_del() takes conn->lock and then calls cancel_work_sync() for
pending_rx_work. process_pending_rx() takes the same mutex, so teardown
can deadlock against the worker it is flushing.
This issue was found by our static analysis tool and then manually
reviewed against the current tree.
The grounded PoC kept the l2cap_conn_ready() -> queue_work(...,
&conn->pending_rx_work) submit path, the l2cap_conn_del() ->
cancel_work_sync(&conn->pending_rx_work) teardown path, and the
process_pending_rx() -> mutex_lock(&conn->lock) worker edge. Lockdep
reported:
WARNING: possible circular locking dependency detected
process_pending_rx+0x21/0x2a [vuln_msv]
l2cap_conn_del.constprop.0+0x3f/0x4e [vuln_msv]
*** DEADLOCK ***
Cancel pending_rx_work before taking conn->lock, matching the existing
lock-before-drain ordering used for the two delayed works in the same
teardown path. The pending_rx queue is still purged after the work has
been cancelled and conn->lock has been acquired.
Fixes: 7ab56c3a6e ("Bluetooth: Fix deadlock in l2cap_conn_del()")
Cc: stable@vger.kernel.org
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
iso_conn_big_sync() drops the socket lock to call hci_get_route() and
then re-acquires it, but dereferences iso_pi(sk)->conn->hcon afterwards
without re-checking that conn is still valid.
While the lock is dropped, the connection can be torn down under the
same socket lock: iso_disconn_cfm() -> iso_conn_del() -> iso_chan_del()
sets iso_pi(sk)->conn to NULL (and the broadcast teardown path can also
clear conn->hcon on its own). When iso_conn_big_sync() re-acquires the
lock and reads conn->hcon, conn may be NULL, causing a NULL pointer
dereference (hcon is the first member of struct iso_conn).
This path is reached from iso_sock_recvmsg() for a PA-sync broadcast
sink socket (BT_SK_DEFER_SETUP | BT_SK_PA_SYNC), so the dropped-lock
window can race with connection teardown driven by controller events.
Re-validate iso_pi(sk)->conn and its hcon after re-acquiring the socket
lock and bail out if the connection went away, as already done in the
sibling iso_sock_rebind_bc().
Fixes: 7a17308c17 ("Bluetooth: iso: Fix circular lock in iso_conn_big_sync")
Cc: stable@vger.kernel.org
Signed-off-by: Muhammad Bilal <meatuni001@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
b66774b48d ("Bluetooth: L2CAP: Fix UAF in channel timeout by holding
conn ref") don't reset the chan->conn to NULL anymore making the bt#
netdev not be remove once the last l2cap_chan_del is removed.
Instead of restoring the original behavior this remove the logic of
keeping the interface after the last channel is removed because it
never worked as intended and the l2cap_chan_del always detach its
l2cap_conn which results in always removing the channel anyway.
Fixes: b66774b48d ("Bluetooth: L2CAP: Fix UAF in channel timeout by holding conn ref")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add the power supply property to the Root Port child node to support the
new PCI pwrctrl framework.
Legacy power supply property is retained for backward compatibility with
existing kernels. New device trees should specify power supply at the
Root Port level to utilize the pwrctrl framework.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the power supply property to the Root Port child node to support the
new PCI pwrctrl framework.
Legacy power supply property is retained for backward compatibility with
existing kernels. New device trees should specify power supply at the
Root Port level to utilize the pwrctrl framework.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The export ccu_mux_helper_apply_prediv() symbol is actually not
necessary. No module other than sunxi-ccu would use it at the moment
so just remove the export.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patch.msgid.link/20260706-a733-rtc-v4-7-f330728db3d3@baylibre.com
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
The sun6i-rtc CCU driver currently uses a global static variable to
denote whether calibration is supported, which makes IOSC operations
tightly coupled to this file.
Convert this into a feature bit to decouple the logic. This allows the
IOSC clock code to be moved into a shared module for reuse by other SoCs.
Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech>
Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patch.msgid.link/20260706-a733-rtc-v4-5-f330728db3d3@baylibre.com
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
With sun6i-rtc compatible devices, the "ext-osc32k" clock input
is optional for the devices that support this input (r329 and onward).
Probably preparing for older SoC support, the driver does something funny
when parsing DT. It check if "ext-osc32k" is present in the clock-names and
if it is not, it uses the first clock as "ext-osc32k". This clock will
actually be the rtc bus clock so what the driver does is wrong.
At the moment, the driver does not support the older SoCs that would have
an external 32k clock provided on index #0 so just remove this quirk.
Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patch.msgid.link/20260706-a733-rtc-v4-4-f330728db3d3@baylibre.com
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
When registering clocks with sunxi_ccu_probe(), the number of ccu_clocks
and the number of hw clocks might be different, eventhough they usually are
the same.
If they are different, it could lead to out-of-bound access or registered
clock left behind on error.
Use a different variable when iterating on hw clocks so every registered
clock, and only those, gets unregistered on error.
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/r/20260629131254.7E34C1F00A3A@smtp.kernel.org
Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patch.msgid.link/20260706-a733-rtc-v4-3-f330728db3d3@baylibre.com
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
Add a new rtc compatible for the sun60i-a733 SoC and new IDs for the
peripheral oscillator clock gates of this SoC.
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patch.msgid.link/20260706-a733-rtc-v4-2-f330728db3d3@baylibre.com
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
On h616 and r329 chips, clock output names are never defined through DT and
are not meant to be. Just disallow the property for those chips.
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: http://lore.kernel.org/r/20260629125305.0DF981F000E9@smtp.kernel.org
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patch.msgid.link/20260706-a733-rtc-v4-1-f330728db3d3@baylibre.com
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
Move the power supply properties from the PCIe controller nodes to the
Root Port child nodes to support the new PCI pwrctrl framework.
Since i.MX95 is the new platform that under development phase, it should
be fine to simply move the power supply properties.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the power supply properties to the Root Port child nodes to support
the new PCI pwrctrl framework.
Legacy power supply properties are retained for backward compatibility
with existing kernels. New device trees should specify power supplies at
the Root Port level to utilize the pwrctrl framework.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the power supply properties to the Root Port child nodes to support
the new PCI pwrctrl framework.
Legacy power supply properties are retained for backward compatibility
with existing kernels. New device trees should specify power supplies at
the Root Port level to utilize the pwrctrl framework.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the power supply properties to the Root Port child nodes to support
the new PCI pwrctrl framework.
Legacy power supply properties are retained for backward compatibility
with existing kernels. New device trees should specify power supplies at
the Root Port level to utilize the pwrctrl framework.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the power supply property to the Root Port child node to support the
new PCI pwrctrl framework.
Legacy power supply property is retained for backward compatibility with
existing kernels. New device trees should specify power supply at the
Root Port level to utilize the pwrctrl framework.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Convert the Texas Instruments MMC host controller bindings
to DT schema.
Note that the OMAP2420 driver will not work with OMAP2430 or later omaps.
Please see the OMAP HSMMC driver for current OMAPs.
Signed-off-by: Eduard Bostina <egbostina@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
On the DART-MX95 platform, INL1/DMICDAT1 is used as the DMIC data line.
Add the wlf,in1l-as-dmicdat1 property to reflect this configuration.
This enables the internal MUX to switch between the ADC and DMIC as the
capture input.
Co-developed-by: Alexander Herfurtner <alexander.h@variscite.com>
Signed-off-by: Alexander Herfurtner <alexander.h@variscite.com>
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable the NETC and NETCMIX block control nodes on the DART-MX95 SoM.
These block control nodes are required to enable and use the NETC
Ethernet ports.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Correct spaces or mix of tabs+spaces into proper tab-indented lines.
No functional impact (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Fix two places where the wrong type or conversion of little-endian
types to fix the following sparse warnings:
drivers/mmc/host/cqhci-core.c:487:15: warning: incorrect type in assignment (different base types)
drivers/mmc/host/cqhci-core.c:487:15: expected restricted __le32 [usertype]
drivers/mmc/host/cqhci-core.c:487:15: got int
drivers/mmc/host/cqhci-core.c:566:19: warning: incorrect type in assignment (different base types)
drivers/mmc/host/cqhci-core.c:566:19: expected unsigned long long [usertype] *task_desc
drivers/mmc/host/cqhci-core.c:566:19: got restricted __le64 [usertype] *
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Avoid using intel_context_put() before intel_context_init() in
execlists_create_virtual() as the kref_put() inside would lead
to NULL deref on the IOCTL path when sched_engine allocation fails.
Discovered using AI-assisted static analysis confirmed by
Intel Product Security.
Reported-by: Martin Hodo <martin.hodo@intel.com>
Fixes: 3e28d37146 ("drm/i915: Move priolist to new i915_sched_engine object")
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tvrtko Ursulin <tursulin@ursulin.net>
Cc: <stable@vger.kernel.org> # v5.15+
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
Link: https://lore.kernel.org/r/20260701114513.221254-1-joonas.lahtinen@linux.intel.com
(cherry picked from commit 4f2a12f2d5)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The loop in intel_dp_check_mst_status() keeps servicing interrupts
originating from the sink without bound. Add an upper bound to the new
interrupts occurring during interrupt processing to not get stuck on
potentially stuck sink devices. Use arbitrary 32 tries to clear incoming
interrupts in one go.
Discovered using AI-assisted static analysis confirmed by Intel Product
Security.
Note: The condition likely pre-dates the commit in the Fixes: tag, but
this is about as far back as a backport has any chance of
succeeding. Before that, the retry had a goto.
Reported-by: Martin Hodo <martin.hodo@intel.com>
Fixes: 3c0ec2c2d5 ("drm/i915: Flatten intel_dp_check_mst_status() a bit")
Cc: stable@vger.kernel.org # v5.8+
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260625142204.1078287-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit b4ea527213)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
According to Bspec we only need to write SSC Enable PLL A bit
and leave PLL B bit alone in PORT_CLOCK_CTL register.
Bspec: 74667, 74492
Fixes: 3383ba2479 ("drm/i915/ltphy: Enable SSC during port clock programming")
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20260701091503.1302226-3-suraj.kandpal@intel.com
(cherry picked from commit 8e27f75203)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Since actively working on TI AM654 SDHCI driver, adding myself
as a maintainer of this driver.
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
vub300_cmndwork_thread() holds cmd_mutex while it sends a command and
waits for the command response. If the response wait times out,
__vub300_command_response() kills the command URBs and then synchronously
resets the USB device through usb_reset_device().
That reset path re-enters the driver through vub300_pre_reset(), which
also takes cmd_mutex. The worker therefore tries to acquire the same
mutex recursively while it is still holding it from the command path.
This issue was found by our static analysis tool and then manually
reviewed against the current tree.
The grounded PoC kept the real worker and timeout/reset carrier:
vub300_cmndwork_thread()
__vub300_command_response()
usb_lock_device_for_reset()
usb_reset_device()
vub300_pre_reset()
Lockdep reported the same-task recursive acquisition on cmd_mutex:
WARNING: possible recursive locking detected
... (&test_vub300.cmd_mutex) ... at: usb_reset_device... [vuln_msv]
... (&test_vub300.cmd_mutex) ... at: vub300_cmndwork_thread+0x12/0x20 [vuln_msv]
Workqueue: vub300_cmd_wq vub300_cmndwork_thread [vuln_msv]
*** DEADLOCK ***
Return a flag from __vub300_command_response() when the timeout path needs
a device reset, then perform the reset after vub300_cmndwork_thread() has
cleared the in-flight command state and dropped cmd_mutex. The reset is
still attempted before mmc_request_done(), preserving the existing request
completion ordering while avoiding the recursive lock.
Fixes: 88095e7b47 ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
moxart_transfer_dma() waits for the DMA completion but ignores
wait_for_completion_interruptible_timeout(). It then unconditionally
reports the full transfer length in data->bytes_xfered.
Terminate the DMA channel and set data->error when the wait is
interrupted or times out. Only report host->data_len as transferred
after the completion is observed.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
The vub300 driver lifetime-manages its controller state using
vub300->kref, with vub300_delete() freeing the mmc host when the last
reference is dropped. The probe error path after the inactivity timer has
been armed still bypasses that lifetime rule, however, and falls through
to mmc_free_host() directly if mmc_add_host() fails.
The race window is between arming the inactivity timer and reaching the
probe error unwind after mmc_add_host() fails:
probe thread timer/workqueue
------------ ---------------
kref_init(&vub300->kref) ref = 1
kref_get(&vub300->kref) ref = 2, timer ref
add_timer(inactivity_timer) fires after one second
|
| race window
|<---------------------------------------------------->
|
mmc_add_host(mmc)
inactivity timer fires
vub300_queue_dead_work()
kref_get() ref = 3
queue_work(deadwork)
mmc_add_host() fails
timer_delete_sync()
mmc_free_host(mmc)
frees vub300
deadwork runs
use-after-free
The inactivity timeout is one second, so this would require
mmc_add_host() to both fail and take more than one second to do so. This
is unlikely to happen in practice, but the error path is still wrong.
timer_delete_sync() only waits for the timer callback itself. It does
not flush deadwork that the callback may already have queued. As a
result, queued deadwork can still hold a kref while the probe error path
directly frees the backing mmc host, including the vub300 storage.
Fix this by using the same lifetime mechanism as disconnect. Clear
vub300->interface so that the timer callback and any queued deadwork
return early and drop their references, then drop the initial probe
reference and return without falling through to err_free_host.
Fixes: 0613ad2401 ("mmc: vub300: fix return value check of mmc_add_host()")
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
The driver explicitly sets the .driver_data member of struct
pnp_device_id to zero without relying on that value. Drop these unused
assignments.
While touching this array use a named initializer for .id and simplify
the list terminator.
This patch doesn't modify the compiled array, only its representation in
source form benefits. The former was confirmed with an x86 build.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
The implementation of the readX() and writeX() family of IO access
functions is non-standard on ColdFire platforms. They check the supplied
IO address and will return either big or little endian results based on
that check. This is non-standard, they are expected to always return
little-endian byte ordered data. Unfortunately this behavior also means
that ioreadX()/iowroteX() and their big-endian counter parts
ioreadXbe()/iowriteXbe() are wrong. This is now in the process of being
cleaned up and fixed.
Change the use of the readX() and writeX() access functions in this driver
to use the recently defined specific ColdFire internal SoC hardware IO
access functions mcf_read8()/mcf_read16()/mcf_read32() and
mcf_write8()/mcf_write16()/mcf_write32().
There is no functional change to the driver. Though it does have the
effect of making the IO access slightly more efficient, since there is
no longer a need to do the address check at every register access.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Tested-by: Angelo Dureghello <adureghello@baylibre.com>
Acked-by: Angelo Dureghello <adureghello@baylibre.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Support for PXA93x chips was removed in commit d711b8a298 ("ARM: pxa:
remove pxa93x support"), but some code to handle them remains. Remove
it.
Discovered while searching for CONFIG_* symbols referenced in code but
not defined in any Kconfig file.
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
HCI_UART_SENDING bit in tx_state means write_work is pending and blocks
queueing it again. Currently this bit is not cleared when canceling the
work in hci_uart_close(), which blocks future writes when device is
reopened later if write_work was pending.
Fix by clearing HCI_UART_SENDING when canceling the work.
Also make clearing of tx_skb safe by using disable_work_sync +
enable_work instead of just cancel_work_sync. hci_uart_flush() purges
the proto tx queue so we can cancel the pending write_work there,
instead of doing it just in hci_uart_close(). Re-enable and possibly
requeue the work after queue flush.
Fixes: c1bb9336ae ("Bluetooth: hci_uart: fix UAFs and race conditions in close and init paths")
Link: https://lore.kernel.org/linux-bluetooth/07e0a28650773abec711ee492fdb1bf5d21a6c98.camel@iki.fi/
Cc: stable@vger.kernel.org
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When transfer was stopped in STATE_DATA_BUSY state, there was no call to
dma_ops->cleanup function, so the DMA mapped buffer was never properly
unmapped. Fix this by calling dw_mci_stop_dma() function also in that
state to ensure proper cleanup call when DMA transfer was used.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
...in hope of removing d_time one day.
Fixes: 2396356a94 ("fuse: add more control over cache invalidation behaviour")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fix logic issues introduced by the kzalloc_flex() conversion in
mmc_test_alloc_mem() due to interaction with the __counted_by
annotation on the flexible array.
Bounds-checking sanitizers rely on the counter field reflecting the
allocated array size before any array access occurs. However, use
mem->cnt both as the allocation size and as the runtime insertion
index, causing incorrect indexing and potentially invalid bounds
tracking.
Initialize mem->cnt to the maximum allocated number of segments
immediately after kzalloc_flex(), then use a separate local index
variable to track successfully allocated entries. Update mem->cnt to
the actual number of initialized elements before returning or entering
the cleanup path.
Also rewrite mmc_test_free_mem() to use a forward for-loop, improving
readability and ensuring only initialized entries are freed.
Fixes: c3126dccfd ("mmc: mmc_test: use kzalloc_flex")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
The intmask parameter of cqhci_irq() is never used within the function
body. The function reads the CQHCI interrupt status directly via
cqhci_readl() and processes interrupts independently of the SDHCI
intmask value passed by callers.
Signed-off-by: Chanwoo Lee <cw9316.lee@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Fix undefined reference to `snd_soc_acpi_amd_sdca_is_device_rt712_vb`
linker error when CONFIG_SND_SOC_ACPI_AMD_MATCH=y and
CONFIG_SND_SOC_ACPI_AMD_SDCA_QUIRKS=m, which causes built-in code to
reference a symbol only available in a module.
Fix this by changing SND_SOC_ACPI_AMD_SDCA_QUIRKS from tristate to bool
and compiling the quirks code directly into snd-soc-acpi-amd-match
rather than as a separate module. This ensures the quirks symbols are
always available at link time when the match tables reference them.
Fixes: 10d366a846 ("ASoC: amd: acp: Fix Kconfig dependencies for SND_SOC_ACPI_AMD_SDCA_QUIRKS")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Syed Saba Kareem <Syed.SabaKareem@amd.com>
Reviewed-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://patch.msgid.link/20260703123314.147977-1-syed.sabakareem@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On ThinkPad X1 Carbon Gen 13 (Lunar Lake, RT712-SDCA version VA) the
3.5mm headphone jack is silent after rebooting from Windows.
rt712_sdca_va_io_init() gates rt712_sdca_calibration() on the persisted
vendor SW_CONFIG1 flag, and io_init writes SW_CONFIG1=1 at the end
regardless of whether the calibration succeeded. Across a warm reboot
the codec keeps power, so SW_CONFIG1 stays unchanged, the calibration
may be skipped, and the retained state can be invalid, leaving the
headphone amp disabled.
This patch mimics the reset sequence in rt711-sdca.c, it adds an
rt712_sdca_reset() helper, and calls it from io_init so the codec is
reset before initialization. RT712_PARA_VERB_CTL,
RT712_HIDDEN_REG_SW_RESET and RT712_HDA_LEGACY_RESET_CTL are already
defined but were unused. The reset clears SW_CONFIG1 and the analog
state so rt712_sdca_calibration() runs from a clean state and
completes.
Problem reproducible: boot Windows (headphone is good) -> reboot
to Linux (silent).
The reproducibility may depend on Windows' behaviour.
Signed-off-by: Tianze Shao <shaotianze@outlook.com>
Link: https://patch.msgid.link/TYCPR01MB872223CB999D2099A5E0F58DC4F62@TYCPR01MB8722.jpnprd01.prod.outlook.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Runyu Xiao <runyu.xiao@seu.edu.cn> says:
Both cs35l33 and cs35l34 can enter runtime suspend while their threaded
IRQ handlers are still reachable. The suspend path then switches the
driver into regcache cache-only mode and powers the codec down, while
the IRQ thread still expects live status-register access.
This issue was found by our static analysis tool and manually audited on
Linux v6.18.21. Directed QEMU no-device validation further showed that,
after runtime_suspend() completed, the real threaded handlers could
still be injected and would continue past volatile regmap read failures
into their release/update paths.
This series keeps the fix on the suspend actor and applies the same
runtime-suspend/threaded-IRQ ordering repair boundary to both drivers:
- track whether request_threaded_irq() actually succeeded
- disable_irq() before cache_only/power-off in runtime suspend
- enable_irq() only after regcache_sync() in runtime resume
That drains any in-flight threaded handler and blocks new IRQ handling
while the codec is suspended, without mixing in larger IRQ-thread
defensive cleanups.
Build-tested by compiling cs35l33.o and cs35l34.o.
No cs35l33/cs35l34 hardware was available for end-to-end runtime
testing.
Link: https://patch.msgid.link/20260611161553.3378721-1-runyu.xiao@seu.edu.cn
cs35l34_runtime_suspend() currently switches the codec into
regcache_cache_only(true), asserts reset low, and powers the device off
without first quiescing the threaded IRQ registered by
devm_request_threaded_irq(). That leaves a window where
cs35l34_irq_thread() can still run after suspend has removed live
hardware access.
A running system can reach this during runtime PM while the driver still
has critical fault IRQs unmasked. If the threaded handler runs in that
window, it reads volatile INT_STATUS_1..4 after cache_only has been
enabled, ignores the regmap_read() failures, and can still execute the
PROT_RELEASE_CTL release sequence or the BST fault power-down writes.
Use disable_irq() before entering cache_only/reset-low/power-off so any
in-flight threaded handler is drained and no new IRQ thread can run
while the device is suspended. Re-enable the IRQ only after
runtime_resume() has restored live register access with regcache_sync().
Since probe only logs request_threaded_irq() failures and keeps going,
track whether the IRQ was actually installed before disabling or
re-enabling it.
Fixes: c1124c09e1 ("ASoC: cs35l34: Initial commit of the cs35l34 CODEC driver.")
Cc: stable@vger.kernel.org
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Link: https://patch.msgid.link/20260611161553.3378721-3-runyu.xiao@seu.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
cs35l33_runtime_suspend() currently switches the codec into
regcache_cache_only(true) and powers it down without first quiescing the
threaded IRQ registered by devm_request_threaded_irq(). That leaves a
window where cs35l33_irq_thread() can still run after suspend has closed
off live register access.
A running system can reach this during runtime PM while the driver still
has critical fault IRQs unmasked. If the threaded handler runs in that
window, it reads volatile INT_STATUS_1/2 after cache_only has been
enabled, ignores the regmap_read() failures, and can still drive the
AMP_SHORT_RLS, CAL_ERR_RLS, OTE_RLS, and OTW_RLS release paths.
Use disable_irq() before entering cache_only/power-off so any in-flight
threaded handler is drained and no new IRQ thread can run during the
suspended state. Re-enable the IRQ only after runtime_resume() has
restored live register access with regcache_sync(). Since probe only
warns if devm_request_threaded_irq() fails, track whether the IRQ was
actually installed before disabling or re-enabling it.
Fixes: 3333cb7187 ("ASoC: cs35l33: Initial commit of the cs35l33 CODEC driver.")
Cc: stable@vger.kernel.org
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Link: https://patch.msgid.link/20260611161553.3378721-2-runyu.xiao@seu.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
sd_enable_cache() allocates a 512-byte buffer that is never used, hence
let's just drop it.
Signed-off-by: Chanwoo Lee <cw9316.lee@samsung.com>
Reviewed-by: Avri Altman <avri.altman@sandisk.com>
Reviewed-by: Shawn Lin <shawn.lin@linux.dev>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Praveen Talari <praveen.talari@oss.qualcomm.com> says:
The Qualcomm automotive SA8255p SoC relies on firmware to configure
platform resources, including clocks, interconnects and TLMM.
The driver requests resources operations over SCMI using power
and performance protocols.
The SCMI power protocol enables or disables resources like clocks,
interconnect paths, and TLMM (GPIOs) using runtime PM framework APIs,
such as resume/suspend, to control power states(on/off).
The SCMI performance protocol manages SPI frequency, with each
frequency rate represented by a performance level. The driver uses
geni_se_set_perf_opp() API to request the desired frequency rate.
As part of geni_se_set_perf_opp(), the OPP for the requested frequency
is obtained using dev_pm_opp_find_freq_floor() and the performance
level is set using dev_pm_opp_set_opp().
Link: https://patch.msgid.link/20260618-enable-spi-on-sa8255p-v4-0-f5b5067e7e1e@oss.qualcomm.com
The Qualcomm automotive SA8255p SoC relies on firmware to configure
platform resources, including clocks, interconnects and TLMM.
The driver requests resources operations over SCMI using power
and performance protocols.
The SCMI power protocol enables or disables resources like clocks,
interconnect paths, and TLMM (GPIOs) using runtime PM framework APIs,
such as resume/suspend, to control power states(on/off).
The SCMI performance protocol manages SPI frequency, with each
frequency rate represented by a performance level. The driver uses
geni_se_set_perf_opp() API to request the desired frequency rate.
As part of geni_se_set_perf_opp(), the OPP for the requested frequency
is obtained using dev_pm_opp_find_freq_floor() and the performance
level is set using dev_pm_opp_set_opp().
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260618-enable-spi-on-sa8255p-v4-4-f5b5067e7e1e@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To manage GENI serial engine resources during runtime power management,
drivers currently need to call functions for ICC, clock, and
SE resource operations in both suspend and resume paths, resulting in
code duplication across drivers.
The new geni_se_resources_activate() and geni_se_resources_deactivate()
helper APIs addresses this issue by providing a streamlined method to
enable or disable all resources based, thereby eliminating redundancy
across drivers.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Link: https://patch.msgid.link/20260618-enable-spi-on-sa8255p-v4-3-f5b5067e7e1e@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
