Recent check_sections() change added a warning if a documentation tag
member name does not match the detected struct/union member names. Since
the checker knows all possible names, we can suggest known names, so
that it's more obvious how to deal with the warning.
Signed-off-by: Ryszard Knop <ryszard.knop@intel.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Message-ID: <20260717125753.634550-1-ryszard.knop@intel.com>
Add purwa-iot-evk and qcs6490-rb3gen2 platform support to the
usecase firmware lookup table for WCN6855 hw2.1.
These platforms use the nfa765 firmware path for usecase-based
firmware selection.
Also reorder the table entries by compatible string.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04685-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Signed-off-by: Miaoqing Pan <miaoqing.pan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260713020359.3618193-1-miaoqing.pan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in ath11k_wmi_tlv_op_rx(), the firmware buffer is read
without first verifying that the buffer has enough data to hold a
header. This could result in a buffer overread.
Add an upfront length check before dereferencing skb->data as a
wmi_cmd_hdr. The check is placed before the trace_ath11k_wmi_event()
call to preserve the existing trace semantics (tracing the full raw
WMI event including the header), unlike the analogous ath12k fix which
could use skb_pull_data() directly.
Compile tested only.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Assisted-by: Claude:claude-sonnet-4-6
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260716-ath11k_wmi_tlv_op_rx-overread-v1-1-0b972b3f1368@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in ath12k_wmi_op_rx(), the firmware buffer is read without
first verifying that the buffer has enough data to hold a header. This
could result in a buffer overread.
Update the logic to verify the buffer contains at least enough data to
hold a wmi_cmd_hdr before reading from the buffer.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c7-00108-QCAHMTSWPL_V1.0_V2.0_SILICONZ_UPSTREAM-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Assisted-by: Claude:claude-sonnet-4-6
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260716-ath12k_wmi_op_rx-overread-v1-1-327a4b1c2372@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When running 'iw dev wlan0 survey dump' the values for the channel busy
time have the same sequence across bands. This is caused by indexing
into the ath12k survey array using a band-local index rather than the
global index passed by mac80211. This results in surveys for 5 GHz and 6
GHz channels returning values from 2.4 GHz slots, making the survey
unusable on those bands. Further, there are redundant survey slots for
multi-radio/single-phy instances.
Fix by moving the survey data into ath12k_hw so multiple radios under a
single wiphy share one table, and index into it using the global
mac80211 index. A new spinlock in ath12k_hw serialises access to the
survey array, which is now shared across all radios under a single hw.
Band busy-times Before this fix:
2.4 GHz: 9, 2, 2, 2, 4, 2, 10, 16, 4, 12, 5
5 GHz: 9, 2, 2, 2, 4, 2, 10, 16, 4, 12, 5
6 GHz: 9, 2, 2, 2, 4, 2, 10, 16, 4, 12, 5
After this fix, times are independent:
2.4 GHz: 23, 5, 5, 12, 2, 12, 26, 5, 3, 1, 27
5 GHz: 30, 40, 29, 27, 118, 118, 112, 120, 11, 11, 11
6 GHz: 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1
Tested-on: wcn7850 hw2.0 PCI WLAN.IOE_HMT.1.1-00018-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Fixes: 4f242b1d69 ("wifi: ath12k: support get_survey mac op for single wiphy")
Signed-off-by: Matthew Leach <matthew.leach@collabora.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260703-ath12-survey-band-fix-v3-1-2fb050c2505a@collabora.com
[fixed ath12k-check issues]
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
'struct cfg80211_ops' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increases overall security, especially when the structure holds some
function pointers.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
143726 34579 192 178497 2b941 drivers/net/wireless/ath/ath6kl/cfg80211.o
After:
=====
text data bss dec hex filename
144814 33491 192 178497 2b941 drivers/net/wireless/ath/ath6kl/cfg80211.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/5aace954b6ef5c42017b83a1bffb859618e9498a.1784013180.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the station always follows the listen interval regardless of
the DTIM value. The DTIM function does not work as expected. The default
value of the listen interval is 5 so that the STA wakes up every 500ms
when power save is on. This can cause a data transmission delay.
Set the DTIM policy to DTIM stick mode so that the station follows the AP
DTIM interval rather than the listen interval, which is set in the peer
assoc command. DTIM stick mode is preferable per the firmware team's request.
Apply this only for STA vdevs and only when STA power save is supported, to
avoid affecting unsupported targets and P2P client vdevs.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c7-00108-QCAHMTSWPL_V1.0_V2.0_SILICONZ_UPSTREAM-3
Signed-off-by: Daizhuang Bai <daizhuang.bai@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260717014302.284034-1-daizhuang.bai@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Register read/write failures during deauth/teardown transitions are
harmless — mac80211 tries to read survey stats or write slot_time
while the firmware is in a transitional state. The command times
out with -EIO but the adapter recovers and re-authenticates normally.
Downgrade both "writing reg ... failed" and "reading regs failed"
from wiphy_err to wiphy_dbg to reduce dmesg noise. The errors are
still visible with dynamic debug enabled for investigation.
Signed-off-by: Masi Osmani <mas-i@hotmail.de>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://patch.msgid.link/AM7PPF5613FA0B67FB95CB5305CEF9DAA209441A@AM7PPF5613FA0B6.EURP251.PROD.OUTLOOK.COM
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Count PHY errors reported by the hardware in the RX status and
expose the counter through debugfs as rx_phy_errors. Previously,
PHY errors from ar9170_rx_phystatus were silently ignored (marked
with a TODO comment).
The counter helps diagnose RF environment issues (interference,
multipath, low SNR) without requiring monitor mode or additional
tooling.
Signed-off-by: Masi Osmani <mas-i@hotmail.de>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://patch.msgid.link/AM7PPF5613FA0B6B42814E38096301FE9429444A@AM7PPF5613FA0B6.EURP251.PROD.OUTLOOK.COM
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Replace the bare TODO comment in the SMPS configuration handler
with documentation explaining why the driver accepts but does not
act on SMPS mode changes.
The AR9170 advertises SM_PS disabled (both chains always active)
in its HT capabilities. While mac80211 may still send SMPS
configuration requests, implementing static or dynamic SMPS would
require firmware support for per-chain enable/disable that the
AR9170 firmware (v1.9.9) does not provide.
Signed-off-by: Masi Osmani <mas-i@hotmail.de>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://patch.msgid.link/AM7PPF5613FA0B6B76223A73FFC756A19A99444A@AM7PPF5613FA0B6.EURP251.PROD.OUTLOOK.COM
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
'struct ath12k_dp_arch_ops' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increases overall security, especially when the structure holds some
function pointers.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
6318 3384 0 9702 25e6 drivers/net/wireless/ath/ath12k/wifi7/dp.o
After:
=====
text data bss dec hex filename
6478 3224 0 9702 25e6 drivers/net/wireless/ath/ath12k/wifi7/dp.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/969d732e2c6f169e1aa5e89c7e01743a1adb55df.1784010931.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k_wmi_scan_req_arg stores scan parameters in CPU-native byte order,
while ath12k_wmi_send_scan_start_cmd() writes them into a WMI command
buffer whose contents must be in little-endian format. The existing code
copies the channel list and writes s_ssid and hint_bssid related values to
the command buffer without endian conversion. As a result, scan requests
contain invalid parameters on big-endian systems and fail.
Convert the channel list as well as the s_ssid and hint_bssid related
values to little-endian before writing them to the WMI command buffer. This
preserves the existing behaviour on little-endian systems while fixing scan
requests on big-endian architectures.
Signed-off-by: Alexander Wilhelm <alexander.wilhelm@westermo.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260703-fix-channel-list-copy-v2-1-372c39306d79@westermo.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in ath11k_wmi_send_scan_start_cmd(), the logic to populate
the hint_bssid copies the BSSID in the wrong direction, from the
firmware message to the argument buffer. Swap the parameters so that
the BSSID is correctly populated in the firmware message from the
argument buffer.
This issue was reported on ath12k, but exists in ath11k as well.
Compile tested only.
Reported-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Closes: https://lore.kernel.org/linux-wireless/afbff608-a005-43c4-af76-968a58bf0cc3@oss.qualcomm.com/
Fixes: 74601ecfef ("ath11k: Add support for 6g scan hint")
Assisted-by: Claude:claude-sonnet-4-6
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260713-ath12k_wmi_send_scan_start_cmd-bad-hint_bssid-v1-2-4ffc4a472992@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in ath12k_wmi_send_scan_start_cmd(), the logic to populate
the hint_bssid copies the BSSID in the wrong direction, from the
firmware message to the argument buffer. Swap the parameters so that
the BSSID is correctly populated in the firmware message from the
argument buffer.
Compile tested only.
Reported-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Closes: https://lore.kernel.org/linux-wireless/afbff608-a005-43c4-af76-968a58bf0cc3@oss.qualcomm.com/
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Assisted-by: Claude:claude-sonnet-4-6
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260713-ath12k_wmi_send_scan_start_cmd-bad-hint_bssid-v1-1-4ffc4a472992@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the Q6 region contains a read-only firmware region along with
the BDF_MEM_REGION_TYPE and HOST_DDR_REGION_TYPE memory areas. The firmware
expects these writable memory regions to be assigned after the Q6 read-only
section.
However, the ath12k driver currently allocates the HOST_DDR_REGION_TYPE
starting from the base of the Q6 region, which includes the read-only
firmware area. As a result, the allocated memory regions overlap with the
read-only section, causing the firmware to assert during QMI memory
allocation. The Q6 memory region layout is as follows:
Q6 Reserved Memory
+--------------------------------------+
| |
| Read-only Firmware Region |
| (Q6 RO Region) |
| |
+--------------------------------------+ <--- bdf_addr_offset
| Writable Memory Region |
| (BDF + HOST_DDR allocations) |
| |
+--------------------------------------+
Fix this by allocating the required memory regions only after the end of
the read-only region in the Q6 address space. The bdf_addr_offset parameter
indicates where the writable region starts. Both HOST_DDR and BDF regions
are allocated sequentially after this offset, with each region placed
immediately after the previous one to avoid gaps and overlaps.
Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.6-01275-QCAHKSWPL_SILICONZ-1
Fixes: 6757079c58 ("wifi: ath12k: add support for fixed QMI firmware memory")
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Link: https://patch.msgid.link/20260630062048.1615178-4-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k_qmi_assign_target_mem_chunk() uses a large switch-case to handle
both memory region identification and allocation for each memory request
type, leading to redundant allocation logic.
Refactor this by introducing ath12k_qmi_get_mem_reg_name() to map memory
request types to their corresponding reserved memory region names.
Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.6-01275-QCAHKSWPL_SILICONZ-1
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Link: https://patch.msgid.link/20260630062048.1615178-3-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The driver currently retrieves reserved memory regions using index-based
lookup, which depends on the ordering of reserved-memory nodes in the
device tree. Since different platforms define these regions in varying
orders and combinations, this approach is not compatible and can result
in incorrect memory region access.
Switch to looking up memory regions by name instead of index so it does
not depend on node order.
Use names already defined in qcom,ipq5332-wifi.yaml, so there are no
backward compatibility issues.
Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.6-01275-QCAHKSWPL_SILICONZ-1
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Link: https://patch.msgid.link/20260630062048.1615178-2-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently when running 128 clients UDP DL test in 5 GHz HE80 (NSS 2x2),
firmware uses the default max MSDU count (16K MSDUs). This lower limit
causes the firmware to compute a smaller TQM drop threshold, aggregate
packets at a reduced rate, and results in increased packet drops with
TQM drop threshold as the completion reason.
To fix this issue, set WMI_PDEV_PARAM_SET_CONG_CTRL_MAX_MSDUS to the TX
descriptor count using ath12k_wmi_pdev_set_param(). This increases the
TQM drop threshold, reduces drop events, and improves throughput from
~722 Mbps to ~1060 Mbps with 1200 Mbps ingress.
Add a new HW capability flag (supports_cong_ctrl_max_msdus) and enable
the WMI parameter only on supported platforms.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.6-01181-QCAHKSWPL_SILICONZ-1
Signed-off-by: Thiraviyam Mariyappan <thiraviyam.mariyappan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260622062614.760166-1-thiraviyam.mariyappan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The following WMI event handlers currently read from the event buffer
without first verifying that the message was large enough to hold the
expected event:
ath6kl_wmi_scan_complete_rx()
ath6kl_wmi_addba_req_event_rx()
ath6kl_wmi_delba_req_event_rx()
Add length checks to prevent overread.
Fixes: bdcd817079 ("Add ath6kl cleaned up driver")
Assisted-by: Claude:claude-sonnet-4-6
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260711-ath6kl_wmi_scan_complete_rx-v2-1-22dc0f7f45e7@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
devm_clk_get() does not return NULL (only valid clock or ERR pointer),
so simplify the code to drop redundant IS_ERR_OR_NULL().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260705172405.119084-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the ath12k driver, the BDF_MEM_REGION_TYPE address is derived by
adding a fixed bdf_addr_offset to the WCSS Q6 region base address.
The current offset (0xC00000) works only when the Q6 region contains
the IPQ5332 ucode alone. On some IPQ5332 platform variants, additional
devices share the same WCSS Q6 processor and place their firmware
ucode in the same Q6 region. This results in multiple ucode sections
within the region, and the existing offset can cause the BDF memory
region to overlap with firmware read-only sections, which can lead to
firmware crash and driver boot failure.
Increase the bdf_addr_offset to 0x1A00000, determined by analyzing
firmware memory maps across all known IPQ5332 platform variants. This
value represents the upper bound of the largest combined firmware and
ensures all IPQ5332 variants can allocate the BDF region safely without
overlapping firmware regions.
Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.6-01275-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260710053534.879233-1-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
QCC2072 firmware interprets the MLO_LINK_ADD and MLO_START_AS_ACTIVE
flags to control the link state during MLO vdev start. MLO_LINK_ADD
indicates that a link is being added, while MLO_START_AS_ACTIVE specifies
that the link should become active during the start.
When an association link is added without setting MLO_START_AS_ACTIVE,
the firmware may transition the link into a suspended state. In this
case, authentication frames transmitted by the host can be dropped,
leading to repeated authentication retries and eventual timeout,
for example:
wlp1s0: send auth to <AP> (try 1/3)
wlp1s0: send auth to <AP> (try 2/3)
wlp1s0: send auth to <AP> (try 3/3)
wlp1s0: authentication with <AP> timed out
Avoid triggering this behavior by setting the MLO_START_AS_ACTIVE flag
when MLO_ASSOC_LINK is set, which tells the firmware that the current
vdev must not enter suspend mode
Note that this change relies on firmware behavior observed on the QCC2072
platform. The firmware on WCN7850 and QCN9274 does not use the
MLO_START_AS_ACTIVE flag, so this change is effectively a no-op on those
platforms
Tested-on: QCC2072 hw1.0 PCI WLAN.COL.1.0.c2-00068-QCACOLSWPL_V1_TO_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Fixes: d8e1f4a193 ("wifi: ath12k: enable QCC2072 support")
Signed-off-by: Miaoqing Pan <miaoqing.pan@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260704073000.3300099-1-miaoqing.pan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath11k_wmi_tlv_ext_hal_reg_caps() copies firmware regulatory
capability records into soc->hal_reg_cap[] using reg_cap.phy_id as
the destination index. The loop count is bounded by num_phy, but the
phy_id embedded in each record is not checked against the fixed
MAX_RADIOS-sized destination array.
Reject firmware records whose phy_id does not fit soc->hal_reg_cap[]
before copying the parsed capability.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260704011040.26233-1-pengpeng@iscas.ac.cn
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When an error occurs during RX packet processing (e.g., MSDU done
failure), the driver sets rx_confused and drops all subsequent RX
packets until a Wi-Fi ON/OFF cycle clears the flag. This can leave
the device in a bad state where it cannot process RX data traffic.
Instead of leaving the device in such a state, trigger hardware
recovery so that such an error state can be reset and the device
can function again normally.
Tested-on: WCN3990 hw1.0 WLAN.HL.3.2.2.c10-00754-QCAHLSWMTPL-1
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00189
Signed-off-by: Manikanta Pubbisetty <manikanta.pubbisetty@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260710060406.3323260-1-manikanta.pubbisetty@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, IEEE80211_OFFLOAD_ENCAP_4ADDR is set when
IEEE80211_OFFLOAD_ENCAP_ENABLED is present in vif->offload_flags
at the beginning of ath12k_mac_update_vif_offload().
However, if the WMI vdev set_param for tx_encap_type fails,
IEEE80211_OFFLOAD_ENCAP_ENABLED is cleared but
IEEE80211_OFFLOAD_ENCAP_4ADDR remains set, leaving the flags in
an inconsistent state.
Fix this by setting IEEE80211_OFFLOAD_ENCAP_4ADDR only after the
tx_encap_type has been configured via the WMI vdev set parameter.
Compile tested only.
Fixes: 729cad3c3c ("wifi: ath12k: Add 4-address mode support for eth offload")
Signed-off-by: Tamizh Chelvam Raja <tamizh.raja@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260701182428.906441-1-tamizh.raja@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
intel_pstate_tracer imports Gnuplot and numpy before parsing command-line
options. As a result, even "-h" fails if those optional runtime modules are
not installed.
Move the imports to the paths that need them. This lets the help and
invalid-argument paths describe usage without requiring plotting/data
dependencies.
While there, fix a typo in the help text and matching comments.
Signed-off-by: Yousef Alhouseen <alhouseenyousef@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20260624122747.5418-1-alhouseenyousef@gmail.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since at least as far back as commit 0818bf27c0 ("resizable
namespace.c hashes"), we call alloc_large_system_hash() in
mnt_init() which already panics if the table is NULL.
Signed-off-by: Hamza Mahfooz <hamzamahfooz@linux.microsoft.com>
Link: https://patch.msgid.link/20260720112331.1096530-1-hamzamahfooz@linux.microsoft.com
Reviewed-by: Jori Koolstra <jkoolstra@xs4all.nl>
Signed-off-by: Christian Brauner (Amutable) <brauner@kernel.org>
A corrupted directory can trigger the following KASAN report when
ext4_readdir() resumes from an invalid position:
BUG: KASAN: use-after-free in __ext4_check_dir_entry+0x5ef/0x820
Read of size 2 at addr ffff88810a646000 by task repro_linear/509
Call Trace:
<TASK>
dump_stack_lvl+0x53/0x70
print_report+0xd0/0x630
kasan_report+0xce/0x100
__ext4_check_dir_entry+0x5ef/0x820
ext4_readdir+0xcde/0x2b70
iterate_dir+0x1a1/0x520
__x64_sys_getdents64+0x12b/0x220
do_syscall_64+0xf9/0x540
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
KASAN reports use-after-free because the out-of-bounds access lands in an
adjacent freed page. The directory buffer itself is still referenced.
ext4_dir_llseek() invalidates the directory cookie so that ext4_readdir()
rescans directory entries from the start of the block. The rescan checks
only the lower bound of rec_len before advancing. A corrupted rec_len can
therefore place the offset where the block has insufficient space for a
complete directory entry. The rescan itself may dereference that truncated
entry, or the main loop may pass it to __ext4_check_dir_entry(). The latter
reads de->rec_len before validating the range. For example:
block offset 0 4092 4096
|---- de1.rec_len = 4092 -----|----|
de2.inode
| de2.rec_len
^ OOB, reported as UAF
de2 starts at offset 4092 in this 4 KiB block. Its four-byte inode fits in
the block, but its rec_len starts at offset 4096 and crosses the boundary.
The minimum safe length is inode-dependent. Encrypted and casefolded
directory entries need eight additional hash bytes, while a valid metadata
checksum tail is only 12 bytes.
Cache the metadata checksum feature state and derive the minimum directory
entry length from the on-disk format. Use it to bound both the rescan and
the offset passed to the main loop. Report an offset in a truncated block
tail and skip the remainder of the block, while continuing to accept an
offset exactly at the block boundary.
Reported-by: syzbot+5322c5c260eb44d209ed@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=5322c5c260eb44d209ed
Fixes: ac27a0ec11 ("[PATCH] ext4: initial copy of files from ext3")
Signed-off-by: Yao Kai <yaokai34@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Link: https://patch.msgid.link/20260706041313.708346-1-yaokai34@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
After implementing bitwise flags for tracking the inline data write
state in the address space fsdata parameter, the CONVERT_INLINE_DATA
state flag is left unused and can be removed.
Perform this clean-up by:
1) Deleting the CONVERT_INLINE_DATA definition from ext4.h.
2) Removing the void **fsdata argument from both the forward
declaration and the definition of the internal helper
ext4_da_convert_inline_data_to_extent().
3) Removing the void **fsdata argument from the declaration and
definition of ext4_generic_write_inline_data() and updating
the caller ext4_try_to_write_inline_data() and the internal
re-alloc retry logic accordingly.
4) Updating ext4_da_write_begin() to call
ext4_generic_write_inline_data() without the fsdata parameter.
Suggested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Aditya Prakash Srivastava <aditya.ansh182@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20260703045414.1768-2-aditya.ansh182@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Instead of checking the live inode state (ext4_has_inline_data(inode)
and ext4_test_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA)) in the
write_end handlers, use the fsdata parameter of the address space
operations to explicitly pass down the state in which write_begin
prepared the write.
A concurrent thread (such as ext4_page_mkwrite()) can convert the
inline data to an extent between write_begin and write_end. If this
happens, the write_end handlers would previously miss the inline
write_end path and fall through to extent-based write_end logic.
However, since block buffers were never allocated in write_begin,
this resulted in NULL pointer dereferences or data loss because
folio_buffers(folio) was NULL.
Define EXT4_WRITE_DATA_INLINE (4) as a bit flag (Bit 2), treating
fsdata as bitwise flags rather than mutually exclusive enums to keep
states of the write path independent. Communicate this state via
fsdata:
1) ext4_write_begin() and ext4_da_write_begin() set the
EXT4_WRITE_DATA_INLINE bit in *fsdata via bitwise OR when an inline
write is successfully prepared.
2) On entry, ext4_write_begin() clears the EXT4_WRITE_DATA_INLINE bit
to safely handle VFS retries (where generic_perform_write() bypasses
the fsdata initialization on its retry jump).
3) The write_end handlers perform a bitwise AND to check if the
EXT4_WRITE_DATA_INLINE bit is set and invoke the inline write_end
helper accordingly.
Furthermore, during a buffered write, ext4_write_inline_data_end()
acquires the xattr lock after preparing the write. If a concurrent
page fault (ext4_page_mkwrite()) converts the inline data to an extent
after the write_end handlers check the state but before
ext4_write_inline_data_end() acquires the xattr write lock, the
subsequent check will trigger a kernel panic via
BUG_ON(!ext4_has_inline_data(inode)).
To keep git history working and bisectability clean, replace the
BUG_ON check in ext4_write_inline_data_end() with a graceful error-
handling retry path in this same commit. If the inline data is cleared
after locking the xattr, we safely release all resources (releasing
iloc.bh, unlocking/putting the folio, stopping the active journal
transaction handle) and return 0 (VFS retry) to let the generic write
path retry the operation safely.
Reported-by: syzbot+0c89d865531d053abb2d@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=0c89d865531d053abb2d
Fixes: 3fdcfb668f ("ext4: add journalled write support for inline data")
Suggested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Aditya Prakash Srivastava <aditya.ansh182@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20260703045414.1768-1-aditya.ansh182@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
"Notification" is too long and the abbreviated version is used in
several places, which is inconsistent and more ambiguous for users.
Rename it to event, which is easier to keep consistent. To keep the
change small, only change uapi/ + do necessary fix ups, and the rest of
internals can be adjusted in the next release.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://patch.msgid.link/f95ca6717da3c8d3649a1a7f0d883a563f545052.1784726895.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When a DAX write starts before EOF but extends past i_disksize,
ext4_write_checks() skips the IOCB_NOWAIT check because
iocb->ki_pos <= old_size. However, ext4_dax_write_iter() later calls
ext4_journal_start() to prepare for inode extension, which can sleep
waiting for journal space or transaction commit.
This violates NOWAIT semantics and can stall asynchronous I/O frameworks
like io_uring that rely on non-blocking behavior.
Fix this by checking IOCB_NOWAIT before calling ext4_journal_start()
in the extending write path. If NOWAIT is set and extension is needed,
return -EAGAIN so the caller can retry in blocking context.
Example scenario:
- File: i_size = 1000, i_disksize = 1000
- DAX NOWAIT write: offset = 500, count = 2000
- ext4_write_checks(): ki_pos (500) <= old_size (1000), skip NOWAIT check
- ext4_dax_write_iter(): offset + count (2500) > i_disksize (1000)
- ext4_journal_start() → may sleep → violates NOWAIT
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://sashiko.dev/#/patchset/20260618125735.4156639-1-libaokun@linux.alibaba.com?part=5
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Baokun Li <libaokun@linux.alibaba.com>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Link: https://patch.msgid.link/20260629113827.4074335-7-libaokun@linux.alibaba.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
file_modified() passes flags=0 which drops IOCB_NOWAIT, causing
file_update_time() to sleep in ext4_journal_start() via
ext4_dirty_inode() even in non-blocking contexts.
kiocb_modified(iocb) propagates iocb->ki_flags so that
generic_update_time() correctly returns -EAGAIN when IOCB_NOWAIT
is set and ->dirty_inode could block, matching the behavior
already adopted by XFS, FUSE, and ext2.
Affected paths:
- ext4_dio_write_checks(): DIO NOWAIT write
- ext4_write_checks(): shared by buffered (rejects NOWAIT upfront)
and DAX write (supports NOWAIT)
ext4_fallocate() in extents.c is not affected as it has no kiocb.
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Baokun Li <libaokun@linux.alibaba.com>
Link: https://patch.msgid.link/20260629113827.4074335-6-libaokun@linux.alibaba.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
For unaligned DIO writes, the previous ext4_overwrite_io() required the
entire range to fall within a single written extent. This was overly
conservative: the DIO layer only performs partial block zeroing for the
head and tail blocks when they are partially covered by the write.
Middle blocks that are fully covered are written as whole blocks
without any zeroing, so they are safe regardless of extent state.
Therefore exclusive lock is only required when partial block zeroing
will actually happen:
- The head partial block (if any) lands on a hole or unwritten extent.
- The tail partial block (if any) lands on a hole or unwritten extent.
Middle full-cover blocks can be in any state (hole, unwritten, or
written) - block allocation under shared lock is safe per the previous
patch's analysis (inode_dio_begin + i_data_sem protection).
Replace ext4_overwrite_io() with ext4_dio_needs_zeroing(), which
directly answers the question driving the lock decision. It uses at
most two ext4_map_blocks() calls: one for the head partial block (also
catching the case where it spans through the tail), and one for the
tail partial block if not already covered.
This enables shared lock for previously-rejected scenarios such as:
- Unaligned write spanning written extent + mid-range hole + written
extent at the tail.
- Unaligned write where the partial blocks land on written extents but
the middle has unwritten extents.
Performance:
Hardware: /dev/sda (rotational disk, ~1 GB/s sustained write)
Filesystem: ext4 default mkfs
Unaligned DIO writes (14336 bytes at +512 within each 16K stripe).
Each stripe is laid out as [written][unwritten][unwritten][written],
so the head and tail partial blocks land on written extents but the
middle is unwritten. Metric: IOPS.
JOBS Before After speedup
---- -------- --------- -------
1 15,547 17,381 1.12x
2 15,910 34,172 2.15x
4 15,014 57,567 3.83x
8 15,022 81,947 5.46x
16 14,586 99,126 6.80x
32 14,047 92,519 6.59x
Wall time at JOBS=32: 149.3s (Before) -> 22.7s (After), 6.58x faster.
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Baokun Li <libaokun@linux.alibaba.com>
Link: https://patch.msgid.link/20260629113827.4074335-5-libaokun@linux.alibaba.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Currently, ext4_dio_write_checks() calls ext4_overwrite_io() to
determine if a write is a pure overwrite, and upgrades to exclusive
i_rwsem if not. However, ext4_overwrite_io() uses a single
ext4_map_blocks() call which only returns the first contiguous extent of
the same type. A write spanning multiple pre-allocated extents (e.g.
written + unwritten, or two physically discontiguous written extents)
produces a false negative, forcing an unnecessary exclusive lock upgrade.
After commit 5d87c7fca2 ("ext4: avoid starting handle when dio
writing an unwritten extent") and commit 012924f0ee ("ext4: remove
useless ext4_iomap_overwrite_ops"), ext4_iomap_begin()'s fast path
accepts both EXT4_MAP_MAPPED and EXT4_MAP_UNWRITTEN without starting a
journal transaction. The iomap iteration naturally handles multi-extent
ranges: each call returns the mapping for the current segment, and
unwritten-to-written conversion is deferred to ext4_dio_write_end_io().
This means the common case of mixed written/unwritten extents never
reaches ext4_iomap_alloc() at all.
Even for the less common case where the range contains a hole and
ext4_iomap_alloc() is needed, exclusive i_rwsem is still unnecessary for
aligned non-extending writes:
- truncate/punch_hole are kept out: they require exclusive i_rwsem
(blocked by our shared lock during allocation), and inode_dio_begin()
keeps their inode_dio_wait() blocked until in-flight bios complete.
- i_data_sem write-lock inside ext4_map_blocks() serializes concurrent
extent tree modifications (parallel writers to the same hole).
- The journal handle is per-thread and does not require i_rwsem
exclusion.
- i_disksize and orphan list are not involved in non-extending writes.
Skip the ext4_overwrite_io() check entirely for aligned writes by
initializing overwrite to true and only calling ext4_overwrite_io() for
unaligned writes. Unaligned writes still need the extent state check
because concurrent partial block zeroing in the DIO layer requires
exclusive serialization unless the range is a pure written-extent
overwrite.
Performance:
Hardware: /dev/sda (rotational disk, ~1 GB/s sustained write)
Filesystem: ext4 default mkfs
Aligned 8K DIO writes spanning written+unwritten extent boundaries.
Each thread writes its own 1G region sequentially; the file is rebuilt
between runs so every block is written exactly once. Metric: IOPS.
JOBS Before After speedup
---- -------- --------- -------
1 42,322 43,329 1.02x
2 68,516 70,677 1.03x
4 62,489 97,072 1.55x
8 58,701 110,819 1.89x
16 58,569 116,392 1.99x
32 60,860 117,244 1.93x
Wall time at JOBS=32: 69.2s (Before) -> 35.4s (After), 1.96x faster.
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Baokun Li <libaokun@linux.alibaba.com>
Link: https://patch.msgid.link/20260629113827.4074335-4-libaokun@linux.alibaba.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
generic/746 started failing intermittently on ext3 (no-extent inodes).
The test triggers 'Page cache invalidation failure on direct I/O'
warnings and subsequent fsync returns -EIO. Adding a 50ms delay
between ext4_buffered_write_iter() and filemap_write_and_wait_range()
in ext4_dio_write_iter() makes the race almost always reproducible.
On no-extent inodes, DIO writes to holes cannot use unwritten extents,
so ext4_iomap_alloc() leaves m_flags=0 and ext4_map_blocks() returns 0.
The iomap layer then returns -ENOTBLK, causing fallback to buffered I/O.
The fallback path in ext4_dio_write_iter() calls
ext4_buffered_write_iter() which dirties pages, then does flush and
invalidate. However, there's an unprotected window between
ext4_buffered_write_iter() returning (with inode lock released) and
the subsequent flush+invalidate.
Concurrent async DIO completions from other threads can run
kiocb_invalidate_post_direct_write() during this window. If pages have
been re-dirtied, post-invalidation finds dirty pages and triggers the
warning, setting -EIO in the error sequence.
Consider a file with two 4k extents: [hole][written]. Thread A does
DIO to the written extent, while thread B does DIO spanning both:
kworker A (4k DIO, allocated block) kworker B (8k DIO, fallback)
----------------------------------- ----------------------------
inode_lock_shared() inode_lock_shared()
iomap_dio_rw(): iomap_dio_rw():
kiocb_invalidate_pages -> clean iomap_begin -> -ENOTBLK
submit_bio (async) dio->size = 0
inode_unlock_shared() inode_unlock_shared()
[bio pending in block layer] /* fallback: lock released */
ext4_buffered_write_iter()
inode_lock(exclusive)
generic_perform_write()
-> dirty pages [0, 8k]
inode_unlock(exclusive)
/* pages dirty, no lock */
[bio completes] filemap_write_and_wait_range()
iomap_dio_complete() -> flush dirty pages
kiocb_invalidate_post_direct_write() invalidate_mapping_pages()
invalidate_inode_pages2_range()
-> finds dirty page!
-> dio_warn_stale_pagecache()
-> errseq_set(-EIO)
This issue can be triggered through normal I/O paths, not just
intentionally overlapping DIO writes from userspace. For example,
generic/746 uses a loop device where multiple kworkers issue concurrent
I/O to the backing file. Additionally, when block_size < folio_size,
non-overlapping DIO writes that share a large folio can also trigger
the race.
Add inode_dio_wait() in ext4_buffered_write_iter() before
ext4_write_checks() to drain all in-flight DIO. This ensures that
all DIO clears existing pages before submitting IO (via
kiocb_invalidate_pages()), all BIO waits for all DIO to complete
(via inode_dio_wait()), and ext4_write_checks() observes the inode
size after all completed DIO so that ext4_block_zero_eof() does not
race with in-flight DIO, thus eliminating the race.
Fixes: 378f32bab3 ("ext4: introduce direct I/O write using iomap infrastructure")
Suggested-by: Zhang Yi <yi.zhang@huawei.com>
Link: https://patch.msgid.link/d1adcf7c-c276-458d-9cac-68a4410f7626@gmail.com
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Baokun Li <libaokun@linux.alibaba.com>
Link: https://patch.msgid.link/20260629113827.4074335-3-libaokun@linux.alibaba.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Block allocation requires journal access which may sleep, violating
NOWAIT semantics. Return -EAGAIN early when IOMAP_NOWAIT is set,
allowing the caller to retry without the NOWAIT constraint.
This ensures that write paths using IOMAP_NOWAIT (e.g., DIO with
RWF_NOWAIT) will not block on journal operations when blocks need
to be allocated.
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://sashiko.dev/#/patchset/20260611163441.2431805-1-libaokun@linux.alibaba.com?part=1
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Baokun Li <libaokun@linux.alibaba.com>
Link: https://patch.msgid.link/20260629113827.4074335-2-libaokun@linux.alibaba.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
thermometer_add_tz() opens tz_path and then reallocates thermometer->tz.
If realloc fails, the function returns without closing fd.
Close fd before returning on realloc failure to avoid leaking a file descriptor.
Signed-off-by: Amarjeet <amarjeet@intel.com>
Link: https://patch.msgid.link/20260620122637.1334927-1-amarjeet@intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support for the IPQ9650 platform, which includes three Gen3 x2 PCIe
controllers and two Gen3 x1 PCIe controllers. The PHY instances require
the on-chip refgen supply.
Add the IPQ9650 Gen3 x1 and x2 QMP PCIe PHY configurations along with
the refgen regulator supply. Note that an on-chip LDO, driven by the SoC
CX, supplies the PHY voltages without requiring software control. Note
that IPQ9650 does not support CX power collapse or rail scaling.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Link: https://patch.msgid.link/20260710-ipq9650_pcie_phy-v3-2-ef6018818d33@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Document the single-lane and dual-lane QMP PCIe PHYs found on the
IPQ9650 SoC.
Unlike the PHYs in the other supported IPQ SoCs, the IPQ9650 PHYs require
the on-chip refgen supply to power up. Add the refgen-supply property
and require it only for the IPQ9650 compatibles.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Link: https://patch.msgid.link/20260710-ipq9650_pcie_phy-v3-1-ef6018818d33@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is the Chinese translation subtree for 7.3. It includes
the following changes:
- Add the some rust, module-signing docs translation
- Fix/update couples Chinese translation
Above patches are tested by 'make htmldocs'
Signed-off-by: Alex Shi <alexs@kernel.org>
-----BEGIN PGP SIGNATURE-----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=uzq2
-----END PGP SIGNATURE-----
Merge tag 'Chinese-docs-7.3' of gitolite.kernel.org:pub/scm/linux/kernel/git/alexs/linux into alex
Chinese translation docs for 7.3
This is the Chinese translation subtree for 7.3. It includes
the following changes:
- Add the some rust, module-signing docs translation
- Fix/update couples Chinese translation
Above patches are tested by 'make htmldocs'
Signed-off-by: Alex Shi <alexs@kernel.org>
Swap the entries for 3562 and 3563 to keep the table in order of
increasing part number.
There's nothing broken here, it's just cosmetic.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260722143607.1001473-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mike Rapoport says:
====================
bpf, x86: enable EXECMEM_ROX_CACHE for BPF allocations
Hi,
BPF allocations of executable memory on x86 are essentially read-only. Most
paths that call bpf_jit_alloc_exec() immediately make it ROX with
set_memory_rox().
The code generation, at least on x86, uses separately allocated writable
buffers and then updates the actual text memory with text_poke().
These patches do several small adjustments to how BPF allocates executable
memory and enable EXECMEM_ROX_CACHE for BPF allocations on x86.
Acked-by: Song Liu <song@kernel.org>
---
v3 changes:
* replace vmalloc() with vzalloc() in bpf_dispatcher_change_prog()
* rebase on the current bpf-next
v2: https://patch.msgid.link/20260711-execmem-x86-rox-bpf-v0-v2-0-bfd956d35119@kernel.org
* rebase on the current bpf-next
v1: https://patch.msgid.link/20260626-execmem-x86-rox-bpf-v0-v1-0-45a0b0ed4fe9@kernel.org
---
---
Mike Rapoport (Microsoft) (5):
bpf: dispatcher: allocate bpf_dispatcher->rw_image with vzalloc()
bpf: drop __weak from bpf_jit_alloc_exec() and bpf_jit_free_exec()
bpf: alloc_prog_pack(): skip ROX management for already ROX memory
bpf, x86: make sure allocation in arch_bpf_trampoline_size() is writable
x86/bpf: enable EXECMEM_ROX_CACHE for BPF allocations
arch/x86/mm/init.c | 4 ++--
arch/x86/net/bpf_jit_comp.c | 5 ++---
include/linux/filter.h | 1 +
kernel/bpf/core.c | 30 +++++++++++++++++++++---------
kernel/bpf/dispatcher.c | 5 ++++-
5 files changed, 30 insertions(+), 15 deletions(-)
---
base-commit: d1f4b56417
change-id: 20260626-execmem-x86-rox-bpf-v0-b4241ade80df
--
Sincerely yours,
Mike.
====================
Link: https://patch.msgid.link/20260716-execmem-x86-rox-bpf-v0-v3-0-4e76158c01c5@kernel.org
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
BPF core and x86 JIT use text poking and temporary writable buffers and
thus can handle ROX memory.
Enable ROX cache for EXECMEM_BPF when configuration and CPU features allow
that.
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Acked-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/bpf/20260716-execmem-x86-rox-bpf-v0-v3-5-4e76158c01c5@kernel.org
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
arch_bpf_trampoline_size() allocates a buffer to get actual size required
for a trampoline.
This buffer must be in the module address space because
__arch_prepare_bpf_trampoline() calculates rel32 offsets relatively to
that buffer.
In preparation for enabling ROX mode for EXECMEM_BPF make sure that the
allocated memory is writable.
Add bpf_jit_alloc_exec_rw() wrapper for execmem_alloc_rw() and use it for
buffer allocation in arch_bpf_trampoline_size().
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Acked-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/bpf/20260716-execmem-x86-rox-bpf-v0-v3-4-4e76158c01c5@kernel.org
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
