ethtool uses `ETHTOOL_GRXRINGS` to compute how many queues are supported
by RSS. The driver should return the smaller of either:
- The maximum number of RSS queues the device supports, OR
- The number of RX queues configured
Prior to this change, running `ethtool -X $iface default` fails if the
number of queues configured is larger than the number supported by RSS,
even though changing the queue count correctly resets the flowhash to
use all supported queues.
Other drivers (for example, i40e) will succeed but the flow hash will
reset to support the maximum number of queues supported by RSS, even if
that amount is smaller than the configured amount.
Prior to this change:
$ sudo ethtool -L eth1 combined 20
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 20 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 10 11 12 13 14 15
16: 0 1 2 3 4 5 6 7
24: 8 9 10 11 12 13 14 15
32: 0 1 2 3 4 5 6 7
...
You can see that the flowhash was correctly set to use the maximum
number of queues supported by the driver (16).
However, asking the NIC to reset to "default" fails:
$ sudo ethtool -X eth1 default
Cannot set RX flow hash configuration: Invalid argument
After this change, the flowhash can be reset to default which will use
all of the available RSS queues (16) or the configured queue count,
whichever is smaller.
Starting with eth1 which has 10 queues and a flowhash distributing to
all 10 queues:
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 10 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 0 1 2 3 4 5
16: 6 7 8 9 0 1 2 3
...
Increasing the queue count to 48 resets the flowhash to distribute to 16
queues, as it did before this patch:
$ sudo ethtool -L eth1 combined 48
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 16 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 10 11 12 13 14 15
16: 0 1 2 3 4 5 6 7
...
Due to the other bugfix in this series, the flowhash can be set to use
queues 0-5:
$ sudo ethtool -X eth1 equal 5
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 16 RX ring(s):
0: 0 1 2 3 4 0 1 2
8: 3 4 0 1 2 3 4 0
16: 1 2 3 4 0 1 2 3
...
Due to this bugfix, the flowhash can be reset to default and use 16
queues:
$ sudo ethtool -X eth1 default
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 16 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 10 11 12 13 14 15
16: 0 1 2 3 4 5 6 7
...
Fixes: 91cd94bfe4 ("ixgbe: add basic support for setting and getting nfc controls")
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ixgbe currently returns `EINVAL` whenever the flowhash it set by ethtool
because the ethtool code in the kernel passes a non-zero value for hfunc
that ixgbe should allow.
When ethtool is called with `ETHTOOL_SRXFHINDIR`,
`ethtool_set_rxfh_indir` will call ixgbe's set_rxfh function
with `ETH_RSS_HASH_NO_CHANGE`. This value should be accepted.
When ethtool is called with `ETHTOOL_SRSSH`, `ethtool_set_rxfh` will
call ixgbe's set_rxfh function with `rxfh.hfunc`, which appears to be
hardcoded in ixgbe to always be `ETH_RSS_HASH_TOP`. This value should
also be accepted.
Before this patch:
$ sudo ethtool -L eth1 combined 10
$ sudo ethtool -X eth1 default
Cannot set RX flow hash configuration: Invalid argument
After this patch:
$ sudo ethtool -L eth1 combined 10
$ sudo ethtool -X eth1 default
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 10 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 0 1 2 3 4 5
16: 6 7 8 9 0 1 2 3
24: 4 5 6 7 8 9 0 1
...
Fixes: 1c7cf0784e ("ixgbe: support for ethtool set_rxfh")
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The panic reporting code was added in commit 81b18bce48
("Drivers: HV: Send one page worth of kmsg dump over Hyper-V during panic")
It was added to the vmbus driver. The panic reporting has no dependence
on vmbus, and can be enabled at an earlier boot time when Hyper-V is
initialized.
This patch moves the panic reporting code out of vmbus. There is no
functionality changes. During moving, also refactored some cleanup
functions into hv_kmsg_dump_unregister().
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1682030946-6372-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmRBmroUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vwtuA/+LsoJ0ohzhtph5SbVFR45tTYxr1uT
3cUDhRmzEy5m7CPBogETTCn18r0VyPtjj2lgsDL7yubQJzCaQN5Sy8TkL43G/VhL
kEPoP2KedWiaDHpzneLG0QAeRtA9nuZSzLokI1aHAjkFJ7KWlPyrNrBFDSMfxdiF
N47o63q6UaREceM0jRF12FVB7OWLgr2Bx7spI093j3+KiVzC5EpdUveq4DyppNk2
RjertZyWfVlzlV3DZ4yWSGDrya1IDRuCa7U6dNTq2vraEuT1sxCmdgblQJw6VClk
irUF3xPnHZ4f/f2o443e70RV46gUqt8p639ONPm86bQtTPYxFbRGK0NZE5s/xDya
fX0AmCx5/GcIcULxn76aSMTqOGRvzi5ainXdyEKNglxIVLJHqq2JronGVsbJlgjo
QnUwVCThTz/xsRn2VNPV9kdwSgDZeIQ9xyQp8vSXSoQ1o1Yp13oEh02Adds0rFlM
OULN4tEt9kuvR3rSTTPjeFzEd9JPS5DLawlLJemDAJYrerO3Hf3sKHK67mGL3vVu
5PN9YztYeVc/0BMBl2H7aM9w4ISIH8admctGGvPn/3WpxCP4kztmXrD/1FzhWVxm
NojwvRvMWcZJ7mPVXfzdbJ/RBoVxbur+FEKvuGlzgNDMlkwtTbiGFJG+reVoPHHz
MoFc9Y47HNdiK44=
=agMG
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.3-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fix from Bjorn Helgaas:
- Previously we ignored PCI devices if the DT "status" property or the
ACPI _STA method said it was not present.
Per spec, _STA cannot be used for that purpose, and using it that way
caused regressions, so skip the _STA check (Rob Herring)
* tag 'pci-v6.3-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI: Restrict device disabled status check to DT
It is a wrapper around C's `lock_class_key`, which is used by the
synchronisation primitives that are checked with lockdep. This is in
preparation for introducing Rust abstractions for these primitives.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Will Deacon <will@kernel.org>
Cc: Waiman Long <longman@redhat.com>
Reviewed-by: Martin Rodriguez Reboredo <yakoyoku@gmail.com>
Co-developed-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Wedson Almeida Filho <walmeida@microsoft.com>
Reviewed-by: Gary Guo <gary@garyguo.net>
Reviewed-by: Benno Lossin <benno.lossin@proton.me>
Link: https://lore.kernel.org/r/20230411054543.21278-1-wedsonaf@gmail.com
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
This makes it possible to use `T` as a `impl Init<T, E>` for every error
type `E` instead of just `Infallible`.
Signed-off-by: Benno Lossin <benno.lossin@proton.me>
Reviewed-by: Gary Guo <gary@garyguo.net>
Reviewed-by: Martin Rodriguez Reboredo <yakoyoku@gmail.com>
Link: https://lore.kernel.org/r/20230413100157.740697-1-benno.lossin@proton.me
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Currently, a limit of 0 results in a hard coded metering over 6 hours.
Since the default is a set limit, I suspect no one truly depends on this
rather arbitrary setting. Repurpose it for an arguably more useful
"unlimited" mode, where the delay is 0.
Note that if block groups are too new, or go fully empty, there is still
a delay associated with those conditions. Those delays implement
heuristics for not trimming a region we are relatively likely to fully
overwrite soon.
CC: stable@vger.kernel.org # 6.2+
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Boris Burkov <boris@bur.io>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Previously, the default was a relatively conservative 10. This results
in a 100ms delay, so with ~300 discards in a commit, it takes the full
30s till the next commit to finish the discards. On a workstation, this
results in the disk never going idle, wasting power/battery, etc.
Set the default to 1000, which results in using the smallest possible
delay, currently, which is 1ms. This has shown to not pathologically
keep the disk busy by the original reporter.
Link: https://lore.kernel.org/linux-btrfs/Y%2F+n1wS%2F4XAH7X1p@nz/
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2182228
CC: stable@vger.kernel.org # 6.2+
Reviewed-by: Neal Gompa <neal@gompa.dev
Signed-off-by: Boris Burkov <boris@bur.io>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Cleanup bindings dropping unneeded quotes. Once all these are fixed,
checking for this can be enabled in yamllint.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #brcm,iproc-rng200
Link: https://lore.kernel.org/r/20230327170153.4105594-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
- Use uniform language in Kconfig menu entries (Bjorn Helgaas)
- Sort controller Kconfig entries by vendor (Bjorn Helgaas)
* pci/controller/kconfig:
PCI: xilinx: Drop obsolete dependency on COMPILE_TEST
PCI: mobiveil: Sort Kconfig entries by vendor
PCI: dwc: Sort Kconfig entries by vendor
PCI: Sort controller Kconfig entries by vendor
PCI: Use consistent controller Kconfig menu entry language
PCI: xilinx-nwl: Add 'Xilinx' to Kconfig prompt
PCI: hv: Add 'Microsoft' to Kconfig prompt
PCI: meson: Add 'Amlogic' to Kconfig prompt
PCI: Use of_property_present() for testing DT property presence
PCI/PM: Extend D3hot delay for NVIDIA HDA controllers
dt-bindings: PCI: qcom: Document msi-map and msi-map-mask properties
PCI: qcom: Add SM8550 PCIe support
dt-bindings: PCI: qcom: Add SM8550 compatible
PCI: qcom: Add support for SDX55 SoC
dt-bindings: PCI: qcom-ep: Fix the unit address used in example
dt-bindings: PCI: qcom: Add SDX55 SoC
dt-bindings: PCI: qcom: Update maintainers entry
PCI: qcom: Enable async probe by default
PCI: qcom: Add support for system suspend and resume
PCI/PM: Drop pci_bridge_wait_for_secondary_bus() timeout parameter
PCI/PM: Increase wait time after resume
PCI: pciehp: Fix AB-BA deadlock between reset_lock and device_lock
PCI: Fix up L1SS capability for Intel Apollo Lake Root Port
PCI: qcom: Expose link transition counts via debugfs
dt-bindings: PCI: qcom: Add "mhi" register region to supported SoCs
PCI: qcom: Rename qcom_pcie_config_sid_sm8250() to reflect IP version
PCI: qcom: Use macros for defining total no. of clocks & supplies
PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.4.0
PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.3.3
PCI: qcom: Use bulk clock APIs for handling clocks for IP rev 2.3.3
PCI: qcom: Use bulk clock APIs for handling clocks for IP rev 2.3.2
PCI: qcom: Use bulk clock APIs for handling clocks for IP rev 1.0.0
PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.1.0
PCI: qcom: Use lower case for hex
PCI: qcom: Add missing macros for register fields
PCI: qcom: Use bitfield definitions for register fields
PCI: qcom: Sort and group registers and bitfield definitions
PCI: qcom: Remove PCIE20_ prefix from register definitions
PCI: qcom: Fix the incorrect register usage in v2.7.0 config
PCI/EDR: Add edr_handle_event() comments
PCI/EDR: Clear Device Status after EDR error recovery
efi/cper: Remove unnecessary aer.h include
dt-bindings: imx6q-pcie: Restruct i.MX PCIe schema
PCI/P2PDMA: Fix pci_p2pmem_find_many() kernel-doc
EISA: Drop unused pci_bus_for_each_resource() index argument
PCI: Make pci_bus_for_each_resource() index optional
PCI: Document pci_bus_for_each_resource()
PCI: Introduce pci_dev_for_each_resource()
PCI: Introduce pci_resource_n()
PCI: ixp4xx: Use PCI_CONF1_ADDRESS() macro
PCI: mt7621: Use dev_info() to log PCIe card detection
PCI: imx6: Install the fault handler only on compatible match
PCI: layerscape: Add EP mode support for ls1028a
PCI: rcar: Avoid defines prefixed with CONFIG
dt-bindings: PCI: convert amlogic,meson-pcie.txt to dt-schema
PCI: kirin: Select REGMAP_MMIO
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it is
possible to test-build any driver which depends on OF on any architecture
by explicitly selecting OF. Therefore depending on COMPILE_TEST as an
alternative is no longer needed.
Link: https://lore.kernel.org/r/20230407190843.529caf19@endymion.delvare
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: "Krzysztof Wilczyński" <kw@linux.com>
Add the "Xilinx" vendor name to the CONFIG_PCIE_XILINX_NWL Kconfig prompt
so it matches other drivers. Rename from "PCIe Core" to "PCIe controller".
Link: https://lore.kernel.org/r/20230418174336.145585-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Add the "Microsoft" vendor name to the CONFIG_PCI_HYPERV_INTERFACE Kconfig
prompt so it matches other PCIe drivers and other Hyper-V prompts.
Link: https://lore.kernel.org/r/20230418174336.145585-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Add the "Amlogic" vendor name to the CONFIG_PCI_MESON Kconfig prompt to
match other PCIe drivers. Capitalize "Meson" to match other Meson Kconfig
prompts.
Link: https://lore.kernel.org/r/20230418174336.145585-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
- Use correct PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 register for v2.7.0
(Manivannan Sadhasivam)
- Remove "PCIE20_" prefix from register definitions (Manivannan Sadhasivam)
- Sort registers and bitfield declarations (Manivannan Sadhasivam)
- Convert to GENMASK and FIELD_PREP (Manivannan Sadhasivam)
- Use bulk APIs for clocks of IP 1.0.0, 2.3.2, 2.3.3 (Manivannan
Sadhasivam)
- Use bulk APIs for reset of IP 2.1.0, 2.3.3, 2.4.0 (Manivannan Sadhasivam)
- Rename qcom_pcie_config_sid_sm8250() to be non SM8250-specific
(Manivannan Sadhasivam)
- Add DT "mhi" register region for supported SoCs (Manivannan Sadhasivam)
- Expose link transition counts via debugfs to help debug low power issues
(Manivannan Sadhasivam)
- Support system suspend and resume; reduce interconnect bandwidth and turn
off clock and PHY if there are no active devices (Manivannan Sadhasivam)
- Enable async probe by default to reduce boot time (Manivannan Sadhasivam)
- Add Manivannan Sadhasivam as qcom DT binding maintainer, replacing
Stanimir Varbanov (Manivannan Sadhasivam)
- Add DT binding and driver support for Qcom SDX55 SoC (Manivannan
Sadhasivam)
- Add DT binding and driver support for SM8550 SoC (Abel Vesa)
- Document msi-map and msi-map-mask DT properties (Manivannan Sadhasivam)
* pci/controller/qcom:
dt-bindings: PCI: qcom: Document msi-map and msi-map-mask properties
PCI: qcom: Add SM8550 PCIe support
dt-bindings: PCI: qcom: Add SM8550 compatible
PCI: qcom: Add support for SDX55 SoC
dt-bindings: PCI: qcom-ep: Fix the unit address used in example
dt-bindings: PCI: qcom: Add SDX55 SoC
dt-bindings: PCI: qcom: Update maintainers entry
PCI: qcom: Enable async probe by default
PCI: qcom: Add support for system suspend and resume
PCI: qcom: Expose link transition counts via debugfs
dt-bindings: PCI: qcom: Add "mhi" register region to supported SoCs
PCI: qcom: Rename qcom_pcie_config_sid_sm8250() to reflect IP version
PCI: qcom: Use macros for defining total no. of clocks & supplies
PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.4.0
PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.3.3
PCI: qcom: Use bulk clock APIs for handling clocks for IP rev 2.3.3
PCI: qcom: Use bulk clock APIs for handling clocks for IP rev 2.3.2
PCI: qcom: Use bulk clock APIs for handling clocks for IP rev 1.0.0
PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.1.0
PCI: qcom: Use lower case for hex
PCI: qcom: Add missing macros for register fields
PCI: qcom: Use bitfield definitions for register fields
PCI: qcom: Sort and group registers and bitfield definitions
PCI: qcom: Remove PCIE20_ prefix from register definitions
PCI: qcom: Fix the incorrect register usage in v2.7.0 config
- Use the PCI_CONF1_ADDRESS() macro to simplify config space address
computation (Pali Rohár)
* pci/controller/ixp4xx:
PCI: ixp4xx: Use PCI_CONF1_ADDRESS() macro
- Install i.MX6 PCI abort handler only when DT contains a PCI controller
claimed by the imx6 driver (H. Nikolaus Schaller)
* pci/controller/dwc:
PCI: imx6: Install the fault handler only on compatible match
- Wait longer for devices to become ready after resume (as we do for reset)
to accommodate Intel Titan Ridge xHCI devices (Mika Westerberg)
- Drop pci_bridge_wait_for_secondary_bus() timeout parameter since all
callers pass the same value (Mika Westerberg)
- Extend D3hot delay for NVIDIA HDA controllers to avoid unrecoverable
devices after a bus reset (Alex Williamson)
* pci/reset:
PCI/PM: Extend D3hot delay for NVIDIA HDA controllers
PCI/PM: Drop pci_bridge_wait_for_secondary_bus() timeout parameter
PCI/PM: Increase wait time after resume
- Use of_property_present(), instead of lower-level functions like
of_get_property(), for testing DT property presence (Rob Herring)
* pci/enumeration:
PCI: Use of_property_present() for testing DT property presence
- Work around Chromebook firmware issue that corrupts Extended Capability
list (including L1 PM Substates capability) on D3cold -> D0 transitions
(Ron Lee)
* pci/aspm:
PCI: Fix up L1SS capability for Intel Apollo Lake Root Port
- Remove unnecessary <linux/aer.h> includes (Bjorn Helgaas)
- Clear Device Status after EDR error recovery. Firmware collects EDR
error information, but the OS is responsible for clearing it (Kuppuswamy
Sathyanarayanan)
* pci/aer:
PCI/EDR: Add edr_handle_event() comments
PCI/EDR: Clear Device Status after EDR error recovery
efi/cper: Remove unnecessary aer.h include
There's a lot of code here that hard-codes that the
data is a single page, and right now that seems to
be sufficient, but to make it easier to change this
in the future, add a new STUB_DATA_PAGES constant
and use it throughout the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
By not doing the user code cflags mangling we can simply
break the build for any user code sneaking into modules.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Make some cleanups, add and fix some comments and document
here that we shouldn't export (libc) symbols for "_user.c"
code, rather such should work like hostfs does now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Since printf() cannot be used in kernel threads (it
uses too much stack space) don't export it for modules
either.
This should leave us exporting only things that are
absolutely critical (such as memset and friends) and
things that are injected by the compiler (stack guard
and similar.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Instead of exporting the set of functions provided by
glibc that are needed for hostfs_user.c, just build that
into the kernel image whenever hostfs is built, and then
export _those_ functions cleanly, to be independent of
the libc implementation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
If the exported glibc functions don't exist, we get link
failures. Avoid that by adding __weak so they're allowed
to not exist.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Cleanup bindings dropping unneeded quotes. Once all these are fixed,
checking for this can be enabled in yamllint.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20230322173501.3970991-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Cleanup bindings dropping unneeded quotes. Once all these are fixed,
checking for this can be enabled in yamllint.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230327170205.4106310-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
'deprecated' is a boolean type which should have a value of 'true' rather
than 'yes'.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230418150643.1529895-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
The trailing "/" in "lvds.yaml/#" is not a valid JSON pointer. The existing
jsonschema package allows it, but coming changes make allowed "$ref" URIs
stricter.
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20230418150658.1535120-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
- Build: Rust + GCC build fix and 'grep' warning fix.
- Code: Missing 'extern "C"' fix.
- Scripts: 'is_rust_module.sh' and 'generate_rust_analyzer.py' fixes.
- A couple trivial fixes.
-----BEGIN PGP SIGNATURE-----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=zdCa
-----END PGP SIGNATURE-----
Merge tag 'rust-fixes-6.3' of https://github.com/Rust-for-Linux/linux
Pull Rust fixes from Miguel Ojeda:
"Most of these are straightforward.
The last one is more complex, but it only touches Rust + GCC builds
which are for the moment best-effort.
- Code: Missing 'extern "C"' fix.
- Scripts: 'is_rust_module.sh' and 'generate_rust_analyzer.py' fixes.
- A couple trivial fixes
- Build: Rust + GCC build fix and 'grep' warning fix"
* tag 'rust-fixes-6.3' of https://github.com/Rust-for-Linux/linux:
rust: allow to use INIT_STACK_ALL_ZERO
rust: fix regexp in scripts/is_rust_module.sh
rust: build: Fix grep warning
scripts: generate_rust_analyzer: Handle sub-modules with no Makefile
rust: kernel: Mark rust_fmt_argument as extern "C"
rust: sort uml documentation arch support table
rust: str: fix requierments->requirements typo
We tested and found an alarm caused by nbd_ioctl arg without verification.
The UBSAN warning calltrace like below:
UBSAN: Undefined behaviour in fs/buffer.c:1709:35
signed integer overflow:
-9223372036854775808 - 1 cannot be represented in type 'long long int'
CPU: 3 PID: 2523 Comm: syz-executor.0 Not tainted 4.19.90 #1
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace+0x0/0x3f0 arch/arm64/kernel/time.c:78
show_stack+0x28/0x38 arch/arm64/kernel/traps.c:158
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x170/0x1dc lib/dump_stack.c:118
ubsan_epilogue+0x18/0xb4 lib/ubsan.c:161
handle_overflow+0x188/0x1dc lib/ubsan.c:192
__ubsan_handle_sub_overflow+0x34/0x44 lib/ubsan.c:206
__block_write_full_page+0x94c/0xa20 fs/buffer.c:1709
block_write_full_page+0x1f0/0x280 fs/buffer.c:2934
blkdev_writepage+0x34/0x40 fs/block_dev.c:607
__writepage+0x68/0xe8 mm/page-writeback.c:2305
write_cache_pages+0x44c/0xc70 mm/page-writeback.c:2240
generic_writepages+0xdc/0x148 mm/page-writeback.c:2329
blkdev_writepages+0x2c/0x38 fs/block_dev.c:2114
do_writepages+0xd4/0x250 mm/page-writeback.c:2344
The reason for triggering this warning is __block_write_full_page()
-> i_size_read(inode) - 1 overflow.
inode->i_size is assigned in __nbd_ioctl() -> nbd_set_size() -> bytesize.
We think it is necessary to limit the size of arg to prevent errors.
Moreover, __nbd_ioctl() -> nbd_add_socket(), arg will be cast to int.
Assuming the value of arg is 0x80000000000000001) (on a 64-bit machine),
it will become 1 after the coercion, which will return unexpected results.
Fix it by adding checks to prevent passing in too large numbers.
Signed-off-by: Zhong Jinghua <zhongjinghua@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20230206145805.2645671-1-zhongjinghua@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 6fffbc7ae1 ("PCI: Honor firmware's device disabled status")
checked the firmware device status for both DT and ACPI devices. That
caused a regression in some ACPI systems. The exact reason isn't clear.
It's possibly a firmware bug. For now, at least, refactor the check to
be for DT based systems only.
Note that the original implementation leaked a refcount which is now
correctly handled.
[bhelgaas: Per ACPI r6.5, sec 6.3.7, for devices on an enumerable bus, _STA
must return with bit[0] ("device is present") set]
Link: https://lore.kernel.org/all/m2fs9lgndw.fsf@gmail.com/
Fixes: 6fffbc7ae1 ("PCI: Honor firmware's device disabled status")
Link: https://lore.kernel.org/r/20230419193513.708818-1-robh@kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217317
Reported-by: Donald Hunter <donald.hunter@gmail.com>
Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Donald Hunter <donald.hunter@gmail.com>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Binbin Zhou <zhoubinbin@loongson.cn>
Cc: Liu Peibao <liupeibao@loongson.cn>
Cc: Huacai Chen <chenhuacai@loongson.cn>
If using leak sanitizer then implicitly enable reference count checking.
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230420171812.561603-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Current release - regressions:
- sched: clear actions pointer in miss cookie init fail
- mptcp: fix accept vs worker race
- bpf: fix bpf_arch_text_poke() with new_addr == NULL on s390
- eth: bnxt_en: fix a possible NULL pointer dereference in unload path
- eth: veth: take into account peer device for NETDEV_XDP_ACT_NDO_XMIT xdp_features flag
Current release - new code bugs:
- eth: revert "net/mlx5: Enable management PF initialization"
Previous releases - regressions:
- netfilter: fix recent physdev match breakage
- bpf: fix incorrect verifier pruning due to missing register precision taints
- eth: virtio_net: fix overflow inside xdp_linearize_page()
- eth: cxgb4: fix use after free bugs caused by circular dependency problem
- eth: mlxsw: pci: fix possible crash during initialization
Previous releases - always broken:
- sched: sch_qfq: prevent slab-out-of-bounds in qfq_activate_agg
- netfilter: validate catch-all set elements
- bridge: don't notify FDB entries with "master dynamic"
- eth: bonding: fix memory leak when changing bond type to ethernet
- eth: i40e: fix accessing vsi->active_filters without holding lock
Misc:
- Mat is back as MPTCP co-maintainer
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=xUNa
-----END PGP SIGNATURE-----
Merge tag 'net-6.3-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter and bpf.
There are a few fixes for new code bugs, including the Mellanox one
noted in the last networking pull. No known regressions outstanding.
Current release - regressions:
- sched: clear actions pointer in miss cookie init fail
- mptcp: fix accept vs worker race
- bpf: fix bpf_arch_text_poke() with new_addr == NULL on s390
- eth: bnxt_en: fix a possible NULL pointer dereference in unload
path
- eth: veth: take into account peer device for
NETDEV_XDP_ACT_NDO_XMIT xdp_features flag
Current release - new code bugs:
- eth: revert "net/mlx5: Enable management PF initialization"
Previous releases - regressions:
- netfilter: fix recent physdev match breakage
- bpf: fix incorrect verifier pruning due to missing register
precision taints
- eth: virtio_net: fix overflow inside xdp_linearize_page()
- eth: cxgb4: fix use after free bugs caused by circular dependency
problem
- eth: mlxsw: pci: fix possible crash during initialization
Previous releases - always broken:
- sched: sch_qfq: prevent slab-out-of-bounds in qfq_activate_agg
- netfilter: validate catch-all set elements
- bridge: don't notify FDB entries with "master dynamic"
- eth: bonding: fix memory leak when changing bond type to ethernet
- eth: i40e: fix accessing vsi->active_filters without holding lock
Misc:
- Mat is back as MPTCP co-maintainer"
* tag 'net-6.3-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (33 commits)
net: bridge: switchdev: don't notify FDB entries with "master dynamic"
Revert "net/mlx5: Enable management PF initialization"
MAINTAINERS: Resume MPTCP co-maintainer role
mailmap: add entries for Mat Martineau
e1000e: Disable TSO on i219-LM card to increase speed
bnxt_en: fix free-runnig PHC mode
net: dsa: microchip: ksz8795: Correctly handle huge frame configuration
bpf: Fix incorrect verifier pruning due to missing register precision taints
hamradio: drop ISA_DMA_API dependency
mlxsw: pci: Fix possible crash during initialization
mptcp: fix accept vs worker race
mptcp: stops worker on unaccepted sockets at listener close
net: rpl: fix rpl header size calculation
net: vmxnet3: Fix NULL pointer dereference in vmxnet3_rq_rx_complete()
bonding: Fix memory leak when changing bond type to Ethernet
veth: take into account peer device for NETDEV_XDP_ACT_NDO_XMIT xdp_features flag
mlxfw: fix null-ptr-deref in mlxfw_mfa2_tlv_next()
bnxt_en: Fix a possible NULL pointer dereference in unload path
bnxt_en: Do not initialize PTP on older P3/P4 chips
netfilter: nf_tables: tighten netlink attribute requirements for catch-all elements
...
