Reorder chip enumeration in alphabetical order to make it easier to
see which chips are supported, and to clarify where to add support
new chip types. No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reorder include files in alphabetical order to reduce the chance of
duplicates and to make it clear where new include files should be
added. Drop the unnecessary include of linux/sysfs.h. Include
linux/device.h instead because that is what is actually used.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Many chips supported by this driver clear status registers after it
is read and update it in the next measurement cycle. Normally this falls
under the radar because all registers are only read once per measurement
cycle. However, there is an exception: Status registers are always read
during interrupt and laert handling. This can result in invalid status
reports if userspace reads an alarm attribute immediately afterwards.
Rework alarm/status handling by keeping a shadow register with 'current'
alarms, and by ensuring that the register is either only updated once per
measurement cycle or not cleared.
A second problem is related to alert handling: Alert handling is disabled
for chips with broken alert after an alert was reported, but only
re-enabled if attributes are read by the user. This means that alert
conditions may appear and disappear unnoticed. Remedy the situation
by introducing a worker to periodically read the status register(s) while
alert handling is disabled, and re-enable alerts after the alert condition
clears.
Yet another problem is that sysfs and udev events are currently only
reported to userspace if an alarm is raised, but not if an alarm condition
clears. Use the new worker to detect that situation and also generate
sysfs and udev events in that case.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
So far the driver only generated sysfs and udev events for minimum and
maximum alarms. Also generate events for critical and emergency alarms.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Enabling and disabling PEC for PMBus devices is currently only supported
with a debugfs attribute, which requires debugfs to be enabled and is
thus less than perfect. Take the lm90 driver as example and add a 'pec'
attribute to the I2C device if both the I2C adapter and the PMBus device
support it. Remove the now obsolete 'pec' attribute from debugfs.
Cc: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The indentation is screwed up. I'm not sure quite how the logic
should flow. Someone more familiar with this code should
verify this.
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implement function to get current GFXOFF status for vangogh.
Signed-off-by: André Almeida <andrealmeid@igalia.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check the value of per_pixel_alpha to decide whether the Coverage pixel
blend mode is applicable or not.
Fixes: 76818cdd11 ("drm/amd/display: add Coverage blend mode for overlay plane")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
divide error: 0000 [#1] SMP PTI
CPU: 3 PID: 78925 Comm: tee Not tainted 5.15.50-1-lts #1
Hardware name: MSI MS-7A59/Z270 SLI PLUS (MS-7A59), BIOS 1.90 01/30/2018
RIP: 0010:smu_v11_0_set_fan_speed_rpm+0x11/0x110 [amdgpu]
Speed is user-configurable through a file.
I accidentally set it to zero, and the driver crashed.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: André Almeida <andrealmeid@igalia.com>
Signed-off-by: Yefim Barashkin <mr.b34r@kolabnow.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Various DCE versions had trouble with 36 bpp lb depth, requiring fixes,
last time in commit 353ca0fa56 ("drm/amd/display: Fix 10bit 4K display
on CIK GPUs") for DCE-8. So far >= DCE-11.2 was considered ok, but now I
found out that on DCE-11.2 it causes dithering when there shouldn't be
any, so identity pixel passthrough with identity gamma LUTs doesn't work
when it should. This breaks various important neuroscience applications,
as reported to me by scientific users of Polaris cards under Ubuntu 22.04
with Linux 5.15, and confirmed by testing it myself on DCE-11.2.
Lets only use depth 36 for DCN engines, where my testing showed that it
is both necessary for high color precision output, e.g., RGBA16 fb's,
and not harmful, as far as more than one year in real-world use showed.
DCE engines seem to work fine for high precision output at 30 bpp, so
this ("famous last words") depth 30 should hopefully fix all known problems
without introducing new ones.
Successfully retested on DCE-11.2 Polaris and DCN-1.0 Raven Ridge on
top of Linux 5.19.0-rc2 + drm-next.
Fixes: 353ca0fa56 ("drm/amd/display: Fix 10bit 4K display on CIK GPUs")
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: stable@vger.kernel.org # 5.14.0
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not used outside of dc_dmub_srv.c.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: André Almeida <andrealmeid@igalia.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Drop execute.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2085
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The initialism of RunList Controller is RLC, not RCL
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Fixes for MST, MPO, PSRSU, DP 2.0, Freesync and others
- Add register offsets of NBI and DCN.
- Improvement of ALPM
- Removing assert statement for Linux DM
- Re-implementing ARGB16161616 pixel format
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With single display odm 2:1 policy, when moving windowed MPO across
the display, we experience a momentary lag when we move between the
centre of the display and the right half of the display. This is
caused by the MPO pipe being reallocated when it crosses this
boundary
[How]
Handle two cases:
1. if the head pipe has a MPO pipe already allocated in the old
context, then use that pipe if it is available in the current
context
2. if the head pipe is on the left side, check the right side to
see if it has a MPO pipe already allocated. If so, don't use
that pipe if it is selected as the idle pipe in the current
context
Add new function pointer called .acquire_idle_pipe_for_head_pipe
that will pass in the head pipe and handle case 1
Add find_idle_secondary_pipe_check_mpo() to handle case 2
if we don't hit case 1.
In dc_add_plane_to_context(), start with head pipe and check
case 1 and 2 in call acquire_free_pipe_for_head().
If we are on the right side of the display, check case 1
again by passing in right side pipe as the new head in
call acquire_free_pipe_for_head().
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Ariel Bernstein <Eric.Bernstein@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Add a field to store the NBIO IP offset for use with runtime offset
calculation
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Add a field to store the DCN IP offset for use with runtime offset
calculation
This offset is indexed using reg*_BASE_IDX for the corresponding
group of registers. For example, address of DIG_BE_CNTL instance 0 is
calculated like: dcn_reg_offsets[regDIG0_DIG_BE_CNTL_BASE_IDX] +
regDIG0_DIG_BE_CNTL.
{dcn,nbio}_reg_offsets are used only for the ASICs for which runtime
initializaion of offsets are enabled through the modified SR* macros
that contain an additional REG_STRUCT element in the macro definition.
DCN3.5+ will fail dc_create() if {dcn,nbio}_reg_offsets are null. They
are applicable starting with DCN32/321 and are not used for ASICs
upstreamed before them. ASICs before DCN32/321 will not contain any
computation that involves {dcn,nbio}_reg_offsets. For them, the
address/offset computation is done during compile time.
This is evident from the BASE_INNER definition for compile time vs run
time initialization:
Compile time init: #define BASE_INNER(seg) DCN_BASE__INST0_SEG ## seg
Run time init: #define BASE_INNER(seg) ctx->dcn_reg_offsets[seg]
BASE_INNER macro is local to each dcnxx_resource.c and hence different
ASICs can have either runtime or compile time initialization of offsets.
The computation of offset is done for registers all at once during
driver load and hence it does not introduce any performance overhead
during normal operation.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
There is chance we change dc state while calling dc_link_detect().
As the result of that, grab the dm.dc_lock before detecting link.
Reviewed-by: Hersen Wu <hersen.wu@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
ABGR16161616 colour format was added to dcn10/20/30, and set
any ARGB16161616 to the same value as it (26). As such, the
HDR10 Green Point y value was too far off of the EDID stated
value for DisplayPort.
[How]
Added back the pixel format as 22 for ARGB16161616 for
dcn10/20/30.
Reviewed-by: Reza Amini <reza.amini@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Ethan Wellenreiter <Ethan.Wellenreiter@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Unbounded request logic in resource/DML has some issues where
unbounded request is being enabled incorrectly. SW today enables
unbounded request unconditionally in hardware, on the assumption
that HW can always support it in single pipe scenarios.
This worked until now because the same assumption is made in DML.
A new DML update is needed to fix a bug, where there are single
pipe scenarios where unbounded cannot be enabled, and this change
in DML needs to be ported in, and dcn32 resource logic fixed.
[how]
First, dcn32_resource should program unbounded req in HW according
to unbounded req enablement output from DML, as opposed to DML input
Second, port in DML1 update which disables unbounded req in some
scenarios to fix an issue with poor stutter performance
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Jun Lei <jun.lei@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Port aggregated doorbell support to gfx11.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Port aggregated doorbell support to sdma6.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ring aggregated doorbel to make unmapped queue scheduled in mes firmware.
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Jack Xiao <Jack.Xiao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allocate and enable aggregated doorbell.
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Jack Xiao <Jack.Xiao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move reset_context out of gpu recover function to make it configurable
for different reset purpose.
For the reset way of call gpu_recovery sysfs, force to use full reset
method. Otherwise, try soft reset by default if the related ASIC
supportted, if soft reset failed, will use full reset.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Support SDMA soft reset for SDMA v6.
V3: use ib test to check soft reset.
V4: squash in unused variable fix (Alex)
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Status flags definition is reduced to read
less bytes in SCDC transaction for status update.
[How]
Reduce definition of reserved bytes from 3 to 1
for status update.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On the GC 10.3.7 platform the initial MEC release version #3 can support
atomic operation,so need correct and set its MEC atomic support version to #3.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Ideally link capability should be independent from the link
configuration that we decide to use in enable link. Otherwise if link
capability is changed after validation has completed, we could end up
enabling a link configuration with invalid configuration. This would
lead to over link bandwidth subscription or in the extreme case
causes us to enable HPO link to a DIO stream.
[how]
Add a new struct in pipe ctx called link config. This structure will
contain link configuration to enable a link. It will be populated
during map pool resources after we validate link bandwidth. Remove
the reference of verified link cap during enable link process and
use link config in pipe ctx instead.
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
First MST sideband message returns AUX_RET_ERROR_HPD_DISCON
on certain intel platform. Aux transaction considered failure
if HPD unexpected pulled low. The actual aux transaction success
in such case, hence do not return error.
[how]
Not returning error when AUX_RET_ERROR_HPD_DISCON detected
on the first sideband message.
v2: squash in additional DMI entries
v3: squash in static fix
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since segment_pages is no longer a compile time constant, it looks the
DIV_ROUND_UP(node->size, segment_pages) breaks the 32b build. Simplest
is just to use the ULL variant, but really we should need not need more
than u32 for the page alignment (also we are limited by that due to the
sg->length type), so also make it all u32.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: bc99f1209f ("drm/i915/ttm: fix sg_table construction")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Nirmoy Das <nirmoy.das@linux.intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220712174050.592550-1-matthew.auld@intel.com
Future changes make it necessary to call this function from pv.c.
While we are at it, let's properly document kvm_s390_cpus_from_pv() and
kvm_s390_cpus_to_pv().
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20220628135619.32410-9-imbrenda@linux.ibm.com
Message-Id: <20220628135619.32410-9-imbrenda@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Do not use memset to clean the whole struct kvm_s390_pv; instead,
explicitly clear the fields that need to be cleared.
Upcoming patches will introduce new fields in the struct kvm_s390_pv
that will not need to be cleared.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20220628135619.32410-8-imbrenda@linux.ibm.com
Message-Id: <20220628135619.32410-8-imbrenda@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Due to upcoming changes, it will be possible to temporarily have
multiple protected VMs in the same address space, although only one
will be actually active.
In that scenario, it is necessary to perform an export of every page
that is to be imported, since the hardware does not allow a page
belonging to a protected guest to be imported into a different
protected guest.
This also applies to pages that are shared, and thus accessible by the
host.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20220628135619.32410-7-imbrenda@linux.ibm.com
Message-Id: <20220628135619.32410-7-imbrenda@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Use the new protected_count field as a counter instead of the old
is_protected flag. This will be used in upcoming patches.
Increment the counter when a secure configuration is created, and
decrement it when it is destroyed. Previously the flag was set when the
set secure parameters UVC was performed.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20220628135619.32410-6-imbrenda@linux.ibm.com
Message-Id: <20220628135619.32410-6-imbrenda@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Refactor s390_reset_acc so that it can be reused in upcoming patches.
We don't want to hold all the locks used in a walk_page_range for too
long, and the destroy page UVC does take some time to complete.
Therefore we quickly gather the pages to destroy, and then destroy them
without holding all the locks.
The new refactored function optionally allows to return early without
completing if a fatal signal is pending (and return and appropriate
error code). Two wrappers are provided to call the new function.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Nico Boehr <nrb@linux.ibm.com>
Link: https://lore.kernel.org/r/20220628135619.32410-5-imbrenda@linux.ibm.com
Message-Id: <20220628135619.32410-5-imbrenda@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
With upcoming patches, normal guests might touch secure pages.
This patch extends the existing exception handler to convert the pages
to non secure also when the exception is triggered by a normal guest.
This can happen for example when a secure guest reboots; the first
stage of a secure guest is non secure, and in general a secure guest
can reboot into non-secure mode.
If the secure memory of the previous boot has not been cleared up
completely yet (which will be allowed to happen in an upcoming patch),
a non-secure guest might touch secure memory, which will need to be
handled properly.
This means that gmap faults must be handled and not cause termination
of the process. The handling is the same as userspace accesses, it's
enough to translate the gmap address to a user address and then let the
normal user fault code handle it.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20220628135619.32410-4-imbrenda@linux.ibm.com
Message-Id: <20220628135619.32410-4-imbrenda@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
A secure storage violation is triggered when a protected guest tries to
access secure memory that has been mapped erroneously, or that belongs
to a different protected guest or to the ultravisor.
With upcoming patches, protected guests will be able to trigger secure
storage violations in normal operation. This happens for example if a
protected guest is rebooted with deferred destroy enabled and the new
guest is also protected.
When the new protected guest touches pages that have not yet been
destroyed, and thus are accounted to the previous protected guest, a
secure storage violation is raised.
This patch adds handling of secure storage violations for protected
guests.
This exception is handled by first trying to destroy the page, because
it is expected to belong to a defunct protected guest where a destroy
should be possible. Note that a secure page can only be destroyed if
its protected VM does not have any CPUs, which only happens when the
protected VM is being terminated. If that fails, a normal export of
the page is attempted.
This means that pages that trigger the exception will be made
non-secure (in one way or another) before attempting to use them again
for a different secure guest.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20220628135619.32410-3-imbrenda@linux.ibm.com
Message-Id: <20220628135619.32410-3-imbrenda@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Each secure guest must have a unique ASCE (address space control
element); we must avoid that new guests use the same page for their
ASCE, to avoid errors.
Since the ASCE mostly consists of the address of the topmost page table
(plus some flags), we must not return that memory to the pool unless
the ASCE is no longer in use.
Only a successful Destroy Secure Configuration UVC will make the ASCE
reusable again.
If the Destroy Configuration UVC fails, the ASCE cannot be reused for a
secure guest (either for the ASCE or for other memory areas). To avoid
a collision, it must not be used again. This is a permanent error and
the page becomes in practice unusable, so we set it aside and leak it.
On failure we already leak other memory that belongs to the ultravisor
(i.e. the variable and base storage for a guest) and not leaking the
topmost page table was an oversight.
This error (and thus the leakage) should not happen unless the hardware
is broken or KVM has some unknown serious bug.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Fixes: 29b40f105e ("KVM: s390: protvirt: Add initial vm and cpu lifecycle handling")
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20220628135619.32410-2-imbrenda@linux.ibm.com
Message-Id: <20220628135619.32410-2-imbrenda@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Merge series from nandhini.srikandan@intel.com <nandhini.srikandan@intel.com>:
This patch enables support for DW SPI on Intel Thunder Bay. This patch
set also enables master mode for latest Designware SPI versions. The
driver is tested on Keem Bay and Thunder Bay evaluation board.
Merge series from Yang Yingliang <yangyingliang@huawei.com>:
Patch #1 fix a UAF in mchp_corespi_remove().
Patch #2 and #3 some cleanups to simpify code.
Use IS_ENABLED(CONFIG_XXX) instead of #ifdef/#endif statements to
initialize .enabled, minor simplicity improvement.
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
On failure to allocate the SHA1 tfm, IMA fails to initialize and exits
without freeing the ima_algo_array. Add the missing kfree() for
ima_algo_array to avoid the potential memory leak.
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Fixes: 6d94809af6 ("ima: Allocate and initialize tfm for each PCR bank")
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Currently, an unsigned kernel could be kexec'ed when IMA arch specific
policy is configured unless lockdown is enabled. Enforce kernel
signature verification check in the kexec_file_load syscall when IMA
arch specific policy is configured.
Fixes: 99d5cadfde ("kexec_file: split KEXEC_VERIFY_SIG into KEXEC_SIG and KEXEC_SIG_FORCE")
Reported-and-suggested-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Coiby Xu <coxu@redhat.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
This driver currently prints the link status using four separate
printk calls, which these days gets presented to the user as four
distinct messages, not exactly ideal:
[ 32.582778] eth0: Link is up using
[ 32.582828] internal
[ 32.582837] transceiver at
[ 32.582888] 100Mb/s, Full Duplex.
Restructure the display_link_mode function to use a single netdev_info
call to present all this information as a single message, which is much
nicer:
[ 33.640143] hme 0000:00:01.1 eth0: Link is up using internal transceiver at 100Mb/s, Full Duplex.
The display_forced_link_mode function has a similar structure, so adjust
it in a similar fashion.
Signed-off-by: Nick Bowler <nbowler@draconx.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>