Add power domains dt-bindings for MediaTek Helio X10 (MT6795).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220503141441.125852-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add device-tree binding documentation to represent the Control Backbone
(CBB) version 2.0 used on Tegra234 SoCs.
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device-tree binding documentation to represent the AXI2APB bridges
used by Control Backbone (CBB) 1.0 on Tegra194 SoCs. All errors for APB
slaves are reported as slave error because APB bas single bit to report
error. So, CBB driver needs to further check error status registers of
all the AXI2APB bridges to find error type.
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device-tree binding documentation to represent the Control Backbone
(CBB) version 1.0 used on Tegra194 SoCs.
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the memory client and stream ID definitions for the MGBE hardware
found on Tegra234 SoCs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the clocks and resets used by the MGBE Ethernet hardware found on
Tegra234 SoCs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add power domain IDs for the four MGBE power partitions found on
Tegra234.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add i.MX8MP NoC node to make the interconnect i.MX8MP driver could work.
Currently dynamic frequency scaling of the i.MX8MP NoC has not been
supported, only NoC initial settings are configured by interconnect
driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A pin controlled by the iomuxc-snvs pin controller must be
specified under the dtb's iomuxc-snvs node.
Move the one and only pin of that category from the iomuxc node
and set the pinctrl-0 using it accordingly.
Fixes: 2aa9d62019 ("ARM: dts: imx6ull-colibri: add touchscreen device nodes")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In optee_smc_do_call_with_arg() there is a code path when the argument
struct for RPC is passed appended to the primary argument struct. When
the address of the RPC struct is retrieved there's an invalid check for
success. It should be 'rpc_arg' pass to IS_ERR/PTR_ERR().
Fixes: ed8faf6c8f ("optee: add OPTEE_SMC_CALL_WITH_RPC_ARG and OPTEE_SMC_CALL_WITH_REGD_ARG")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
[jw: added background to the problem]
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
The cpumask that is passed to this function ultimately comes from
irq_data_get_effective_affinity_mask(), which was recently changed to
return a const cpumask pointer. The first level of functions handling
the affinity mask were updated, but not this helper function.
Fixes: 4d0b829881 ("genirq: Return a const cpumask from irq_data_get_affinity_mask")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220708004931.1672-1-samuel@sholland.org
Changes from v1:
* replace some accidental spaces with tabs
In commit f145d411a6 ("crypto: rsa - implement Chinese Remainder Theorem
for faster private key operations") we have started to use the additional
primes and coefficients for RSA private key operations. However, these
additional parameters are not present (defined as 0 integers) in the RSA
test vectors.
Some parameters were borrowed from OpenSSL, so I was able to find the
source. I could not find the public source for 1 vector though, so had to
recover the parameters by implementing Appendix C from [1].
[1]: https://nvlpubs.nist.gov/nistpubs/SpecialPublications/NIST.SP.800-56Br1.pdf
Fixes: f145d411a6 ("crypto: rsa - implement Chinese Remainder Theorem for faster private key operations")
Reported-by: Tasmiya Nalatwad <tasmiya@linux.vnet.ibm.com>
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When mixing bit-field and none bit-filed in packed struct the
none bit-field starts at a distinct memory location, thus adding
an additional byte to the overall structure which is used in
memory zero-ing and other configuration calculations.
Fix this by removing the none bit-field that has a following
bit-field.
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Acked-by: Antoine Tenart <atenart@kernel.org>
Acked-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When kunpeng916 encryption driver is used to deencrypt and decrypt
packets during the softirq, it is not allowed to use mutex lock.
Fixes: 915e4e8413 ("crypto: hisilicon - SEC security accelerator driver")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The argument passed to sec_queue_aw_alloc() should be
SEC_QUEUE_AW_FROCE_NOALLOC instead of SEC_QUEUE_AR_FROCE_NOALLOC.
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In nx842_pseries_init(), we should hold the reference returned by
of_find_compatible_node() and use it to call of_node_put to keep
refcount balance.
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In crypto4xx_probe(), we should hold the reference returned by
of_find_compatible_node() and use it to call of_node_put to keep
refcount balance.
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The compiler complains that p8_ghash_alg isn't declared which is
because the header file aesp8-ppc.h isn't included in ghash.c.
This patch fixes the warning.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
qat_4xxx devices can be configured to allow either crypto or compression
operations. At the moment, devices are configured statically according to
the following rule:
- odd numbered devices assigned to compression services
- even numbered devices assigned to crypto services
Expose the sysfs attribute /sys/bus/pci/devices/<BDF>/qat/cfg_services
to allow to detect the configuration of a device and to change it.
The `cfg_service` attribute is only exposed for qat_4xxx devices and it
is limited to two configurations: (1) "sym;asym" for crypto services and
"dc" for compression services.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Co-developed-by: Tomasz Kowallik <tomaszx.kowalik@intel.com>
Signed-off-by: Tomasz Kowallik <tomaszx.kowalik@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The function adf_sriov_prepare_restart() is used in adf_sriov.c to stop
and shutdown a device preserving its configuration.
Since this function will be re-used by the logic that allows to
reconfigure the device through sysfs, move it to adf_init.c and rename
it as adf_dev_shutdown_cache_cfg();
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The function adf_cfg_add_key_value_param() allows to insert duplicates
entries in the key value store of the driver.
Change the behaviour of that function to the following policy:
- if the key doesn't exist, add it;
- if the key already exists with a different value, then delete it and
replace it with a new one containing the new value;
- if the key exists with the same value, then return without doing
anything.
The behaviour of this function has been changed in order to easily
update key-values in the driver database. In particular this is required
to update the value of the ServiceEnables key used to change the service
loaded on a device.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Expose the device state through an attribute in sysfs and allow to
change it. This is to stop and shutdown a QAT device in order to change
its configuration.
The state attribute has been added to a newly created `qat` attribute
group which will contain all _QAT specific_ attributes.
The logic that implements the sysfs entries is part of a new file,
adf_sysfs.c. This exposes an entry point to allow the driver to create
attributes.
The function that creates the sysfs attributes is called from the probe
function of the driver and not in the state machine init function to
allow the change of states even if the device is in the down state.
In order to restore the device configuration between a transition from
down to up, the function that configures the devices has been abstracted
into the HW data structure.
The `state` attribute is only exposed for qat_4xxx devices.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Co-developed-by: Tomasz Kowallik <tomaszx.kowalik@intel.com>
Signed-off-by: Tomasz Kowallik <tomaszx.kowalik@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix the MAINTAINERS entry for the Synopsys AXS10x reset controller
driver, which still points to a nonexistent .txt file after the device
tree binding .yaml conversion.
Also, fix the devm_reset_control_bulk_get_optional_exclusive() call,
which was defective since its introduction due to a copy & paste error.
-----BEGIN PGP SIGNATURE-----
iI0EABYIADUWIQRRO6F6WdpH1R0vGibVhaclGDdiwAUCYsaxZBcccC56YWJlbEBw
ZW5ndXRyb25peC5kZQAKCRDVhaclGDdiwBznAP0ZIIfZrIixr9OOZAM2TSsTXVq5
vV54E+tfnu700fmBTAD9Hdiprk15QtzZISlI314nt3u8bbrLgVTBGbXlqLfDVQI=
=t6sW
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=cpdV
-----END PGP SIGNATURE-----
Merge tag 'reset-fixes-for-v5.19' of git://git.pengutronix.de/pza/linux into arm/fixes
Reset controller fixes for v5.19
Fix the MAINTAINERS entry for the Synopsys AXS10x reset controller
driver, which still points to a nonexistent .txt file after the device
tree binding .yaml conversion.
Also, fix the devm_reset_control_bulk_get_optional_exclusive() call,
which was defective since its introduction due to a copy & paste error.
* tag 'reset-fixes-for-v5.19' of git://git.pengutronix.de/pza/linux:
reset: Fix devm bulk optional exclusive control getter
MAINTAINERS: rectify entry for SYNOPSYS AXS10x RESET CONTROLLER DRIVER
Link: https://lore.kernel.org/r/20220707101344.3329314-1-p.zabel@pengutronix.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Hardware random, PCI and clock drivers for the PolarFire SoC have been
upstreamed but are not covered by the MAINTAINERS entry, so add them.
Daire is the author of the clock & PCI drivers, so add him as a
maintainer in place of Lewis.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220707142041.4096246-1-conor.dooley@microchip.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The SiFive errata code contains code checking applicable erratas
vs. actually applied erratas to suggest missing erratas to the
user when their Kconfig options are not enabled.
In the main kernel image one can be quite sure that all available
erratas appear at least once, so that check will succeed.
On the other hand modules can very well not use any errata-relevant
code, so the newly added module-alternative support may also patch
the module code, but not touch SiFive-specific erratas at all.
So to restore the original behaviour don't warn when patching
modules. This will keep the warning if necessary for the main kernel
image but prevent spurious warnings for modules.
Of course having such a vendor-specific warning may not be needed at
all, as CONFIG_ERRATA_SIFIVE is selected by CONFIG_SOC_SIFIVE and the
individual erratas are default-y so disabling them requires
deliberate action anyway. But for now just restore the old behaviour.
Fixes: a8e910168b ("riscv: implement module alternatives")
Reported-by: Ron Economos <re@w6rz.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Ron Economos <re@w6rz.net>
Link: https://lore.kernel.org/r/20220608120849.1695191-1-heiko@sntech.de
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Devices might need to control several clocks when scaling the frequency
and voltage. Allow passing array of clock frequencies, similarly to the
voltages.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
dev_pm_opp_set_opp() can be called for any device, it may or may not
have a frequency value associated with it.
If a frequency value isn't available, we pass 0 to _set_opp(). Make it
optional instead by making _set_opp() accept a pointer instead, as the
frequency value is anyway available in the OPP. This makes
dev_pm_opp_set_opp() and _set_opp() completely independent of any
special key value.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reuse _opp_compare_key() in _opp_add_static_v2() instead of just
comparing frequency while finding suspend frequency. Also add a comment
over _opp_compare_key() explaining its return values.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
commit 32715be4fe ("opp: Fix adding OPP entries in a wrong order if
rate is unavailable") removed the only user of this field, get rid of
rest of it now.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The OPP table is called "opp_table" at most of the places and "table" at
few. Make all of them follow the same naming convention, "opp_table".
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
There are three type of helpers, to find exact, ceil, and floor values,
replicated for multiple key types, freq, level, bw. And all of these
helpers share a lot of boilerplate code.
Add generic key finding helpers to reduce code redundancy.
Also update the freq finder helpers to use the new infrastructure.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
This was added few years back, but the code that was supposed to use it
never got merged. Remove the unused helper.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The only user of the custom helper is migrated to use
dev_pm_opp_set_config_regulators() interface. Remove the now unused
custom OPP helper support.
This cleans up _set_opp() and leaves a single code path to be used by
all users.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The OPP core now provides dev_pm_opp_set_config_regulators() interface,
which needs the platforms to just set the OPP voltages instead of both
clk and voltage. The clock is set by the OPP core instead and hence
reduces code redundancy.
Migrate the only user of the custom set_opp() to
dev_pm_opp_set_config_regulators().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
We already have an API for getting voltage information for a single
regulator, dev_pm_opp_get_voltage(), but there is nothing available for
multiple regulator case.
This patch adds a new API, dev_pm_opp_get_supplies(), to get all
information related to the supplies for an OPP.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
In order to reuse the same code path, i.e. clk_set_rate() from
_set_opp(), migrate _generic_set_opp_regulator() to implement a
config_regulators() interface.
It is renamed to _opp_config_regulator_single() and is set as the
preferred config_regulators() interface whenever we have a single
regulator available.
Note that this also drops code responsible for restoring the
voltage/freq in case of errors. We aren't handling that properly
currently, restoring only some of the resources while leaving others out
(like bandwidth and required OPPs). It is better to drop all of it
instead of partial restoration.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Extend the dev_pm_opp_set_config() interface to allow adding
config_regulators() helpers. This helper will be called to set the
voltages of the regulators from the regular path in _set_opp(), while we
are trying to change the OPP.
This will eventually replace the custom set_opp() helper.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Now that we have a central API to handle all OPP table configurations,
migrate the set-prop-name family of helpers to use the new
infrastructure.
The return type and parameter to the APIs change a bit due to this,
update the current users as well in the same commit in order to avoid
breaking builds.
Acked-by: Samuel Holland <samuel@sholland.org> # sun50i
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Now that we have a central API to handle all OPP table configurations,
migrate the attach-genpd family of helpers to use the new
infrastructure.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Now that we have a central API to handle all OPP table configurations,
migrate the set-opp-helper family of helpers to use the new
infrastructure.
The return type and parameter to the APIs change a bit due to this,
update the current users as well in the same commit in order to avoid
breaking builds.
Remove devm_pm_opp_register_set_opp_helper() as it has no users
currently.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Now that we have a central API to handle all OPP table configurations,
migrate the set-clk-name family of helpers to use the new
infrastructure.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>