Commit graph

1,189,987 commits

Author SHA1 Message Date
Marc Kleine-Budde
0ff32bfa0e can: mcp251xfd: mcp251xfd_register_get_dev_id(): use correct length to read dev_id
The device ID register is 32 bits wide. The driver uses incorrectly
the size of a pointer to a u32 to calculate the length of the SPI
transfer. This results in a read of 2 registers on 64 bit platforms.
This is no problem on the Linux side, as the RX buffer of the SPI
transfer is large enough. In the mpc251xfd chip this results in the
read of an undocumented register. So far no problems were observed.

Fix the length of the SPI transfer to read the device ID register
only.

Link: https://lore.kernel.org/all/20220616094914.244440-1-mkl@pengutronix.de
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Reported-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-04 12:46:46 +02:00
Marc Kleine-Budde
d5a972f561 can: mcp251xfd: mcp251xfd_stop(): add missing hrtimer_cancel()
In commit 169d00a256 ("can: mcp251xfd: add TX IRQ coalescing
support") software based TX coalescing was added to the driver. The
key idea is to keep the TX complete IRQ disabled for some time after
processing it and re-enable later by a hrtimer. When bringing the
interface down, this timer has to be stopped.

Add the missing hrtimer_cancel() of the tx_irq_time hrtimer to
mcp251xfd_stop().

Link: https://lore.kernel.org/all/20220620143942.891811-1-mkl@pengutronix.de
Fixes: 169d00a256 ("can: mcp251xfd: add TX IRQ coalescing support")
Cc: stable@vger.kernel.org # v5.18
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-04 12:46:45 +02:00
Thomas Kopp
e3d4ee7d5f can: mcp251xfd: mcp251xfd_regmap_crc_read(): update workaround broken CRC on TBC register
The mcp251xfd compatible chips have an erratum ([1], [2]), where the
received CRC doesn't match the calculated CRC. In commit
c7eb923c3c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work
around broken CRC on TBC register") the following workaround was
implementierend.

- If a CRC read error on the TBC register is detected and the first
  byte is 0x00 or 0x80, the most significant bit of the first byte is
  flipped and the CRC is calculated again.
- If the CRC now matches, the _original_ data is passed to the reader.
  For now we assume transferred data was OK.

New investigations and simulations indicate that the CRC send by the
device is calculated on correct data, and the data is incorrectly
received by the SPI host controller.

Use flipped instead of original data and update workaround description
in mcp251xfd_regmap_crc_read().

[1] mcp2517fd: DS80000792C: "Incorrect CRC for certain READ_CRC commands"
[2] mcp2518fd: DS80000789C: "Incorrect CRC for certain READ_CRC commands"

Link: https://lore.kernel.org/all/DM4PR11MB53901D49578FE265B239E55AFB7C9@DM4PR11MB5390.namprd11.prod.outlook.com
Fixes: c7eb923c3c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work around broken CRC on TBC register")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
[mkl: split into 2 patches, update patch description and documentation]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-04 12:46:45 +02:00
Thomas Kopp
406cc9cdb3 can: mcp251xfd: mcp251xfd_regmap_crc_read(): improve workaround handling for mcp2517fd
The mcp251xfd compatible chips have an erratum ([1], [2]), where the
received CRC doesn't match the calculated CRC. In commit
c7eb923c3c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work
around broken CRC on TBC register") the following workaround was
implementierend.

- If a CRC read error on the TBC register is detected and the first
  byte is 0x00 or 0x80, the most significant bit of the first byte is
  flipped and the CRC is calculated again.
- If the CRC now matches, the _original_ data is passed to the reader.
  For now we assume transferred data was OK.

Measurements on the mcp2517fd show that the workaround is applicable
not only of the lowest byte is 0x00 or 0x80, but also if 3 least
significant bits are set.

Update check on 1st data byte and workaround description accordingly.

[1] mcp2517fd: DS80000792C: "Incorrect CRC for certain READ_CRC commands"
[2] mcp2518fd: DS80000789C: "Incorrect CRC for certain READ_CRC commands"

Link: https://lore.kernel.org/all/DM4PR11MB53901D49578FE265B239E55AFB7C9@DM4PR11MB5390.namprd11.prod.outlook.com
Fixes: c7eb923c3c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work around broken CRC on TBC register")
Cc: stable@vger.kernel.org
Reported-by: Pavel Modilaynen <pavel.modilaynen@volvocars.com>
Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
[mkl: split into 2 patches, update patch description and documentation]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-04 12:46:45 +02:00
Jimmy Assarsson
b3b6df2c56 can: kvaser_usb: kvaser_usb_leaf: fix bittiming limits
Use correct bittiming limits depending on device. For devices based on
USBcanII, Leaf M32C or Leaf i.MX28.

Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Fixes: b4f20130af ("can: kvaser_usb: add support for Kvaser Leaf v2 and usb mini PCIe")
Fixes: f5d4abea3c ("can: kvaser_usb: Add support for the USBcan-II family")
Link: https://lore.kernel.org/all/20220603083820.800246-4-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
[mkl: remove stray netlink.h include]
[mkl: keep struct can_bittiming_const kvaser_usb_flexc_bittiming_const in kvaser_usb_hydra.c]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-04 12:45:43 +02:00
Stefan Wahren
df76234276 mfd: bcm2835-pm: Add support for BCM2711
In BCM2711 the new RPiVid ASB took over V3D. The old ASB is still present
with the ISP and H264 bits, and V3D is in the same place in the new ASB
as the old one.

As per the devicetree bindings, BCM2711 will provide both the old and
new ASB resources, so get both of them and pass them into
'bcm2835-power,' which will take care of selecting which one to use
accordingly.

Since the RPiVid ASB's resources were being provided prior to formalizing
the bindings[1], also support the old DT files that didn't use
'reg-names.'

[1] See: 7dbe8c62ce ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220625113619.15944-8-stefan.wahren@i2se.com
2022-07-04 11:42:20 +01:00
Jimmy Assarsson
e6c80e6010 can: kvaser_usb: kvaser_usb_leaf: fix CAN clock frequency regression
The firmware of M32C based Leaf devices expects bittiming parameters
calculated for 16MHz clock. Since we use the actual clock frequency of
the device, the device may end up with wrong bittiming parameters,
depending on user requested parameters.

This regression affects M32C based Leaf devices with non-16MHz clock.

Fixes: fb12797ab1 ("can: kvaser_usb: get CAN clock frequency from device")
Link: https://lore.kernel.org/all/20220603083820.800246-3-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-04 12:42:05 +02:00
Nicolas Saenz Julienne
01e7865d18 mfd: bcm2835-pm: Use 'reg-names' to get resources
If available in firmware, find resources by their 'reg-names' position
instead of relying on hardcoded offsets. Care is taken to support old
firmware nonetheless.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220625113619.15944-7-stefan.wahren@i2se.com
2022-07-04 11:41:27 +01:00
Jimmy Assarsson
49f274c723 can: kvaser_usb: replace run-time checks with struct kvaser_usb_driver_info
Unify and move compile-time known information into new struct
kvaser_usb_driver_info, in favor of run-time checks.

All Kvaser USBcanII supports listen-only mode and error counter
reporting.

Link: https://lore.kernel.org/all/20220603083820.800246-2-extja@kvaser.com
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
[mkl: move struct kvaser_usb_driver_info into kvaser_usb_core.c]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-04 12:31:25 +02:00
Zhang Jiaming
874bdbfe62 net: hns: Fix spelling mistakes in comments.
Fix spelling of 'waitting' in comments.
remove unnecessary space of 'MDIO_COMMAND_REG 's'.

Signed-off-by: Zhang Jiaming <jiaming@nfschina.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 11:15:45 +01:00
Rick Lindsley
1b18f09d31 ibmvnic: Properly dispose of all skbs during a failover.
During a reset, there may have been transmits in flight that are no
longer valid and cannot be fulfilled.  Resetting and clearing the
queues is insufficient; each skb also needs to be explicitly freed
so that upper levels are not left waiting for confirmation of a
transmit that will never happen.  If this happens frequently enough,
the apparent backlog will cause TCP to begin "congestion control"
unnecessarily, culminating in permanently decreased throughput.

Fixes: d7c0ef36bd ("ibmvnic: Free and re-allocate scrqs when tx/rx scrqs change")
Tested-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Rick Lindsley <ricklind@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 11:09:57 +01:00
David S. Miller
fd4b96c44a Merge branch 'nfp-vlan-strip-and-insert'
Simon Horman says:

====================
nfp: support VLAN strip and insert

this series adds support to the NFP driver for HW offload of both:

* RX VLAN ctag/stag strip
* TX VLAN ctag insert
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 10:44:08 +01:00
Diana Wang
d80702ff12 nfp: support TX VLAN ctag insert
Add support for TX VLAN ctag insert
which may be configured via ethtool.

e.g.
     # ethtool -K $DEV tx-vlan-offload on

The NIC supplies VLAN insert information as packet metadata.
The fields of this VLAN metadata are gotten from sk_buff, including
vlan_proto and vlan tag.

Configuration control bit NFP_NET_CFG_CTRL_TXVLAN_V2 is to
signal availability of ctag-insert features of the firmware.

NFDK is used to communicate via PCIE to NFP-3800 based NICs
while NFD3 is used for other NICs supported by the NFP driver.
The metadata format on tx side of NFD3 is different from NFDK.
This feature is not currently implemented for NFDK.

Signed-off-by: Diana Wang <na.wang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 10:44:08 +01:00
Diana Wang
67d2656b48 nfp: support RX VLAN ctag/stag strip
Add support for RX VLAN ctag/stag strip
which may be configured via ethtool.

e.g.
     # ethtool -K $DEV rx-vlan-offload on
     # ethtool -K $DEV rx-vlan-stag-hw-parse on

Ctag-stripped and stag-stripped cannot be enabled at the same time
because currently the kernel supports only one layer of VLAN stripping.

The NIC supplies VLAN strip information as packet metadata.
The fields of this VLAN metadata are:

* strip flag: 1 for stripped; 0 for unstripped
* tci: VLAN TCI ID
* tpid: 1 for ETH_P_8021AD; 0 for ETH_P_8021Q

Configuration control bits NFP_NET_CFG_CTRL_RXVLAN_V2 and
NFP_NET_CFG_CTRL_RXQINQ are to signal availability of
ctag-strip and stag-strip features of the firmware.

Signed-off-by: Diana Wang <na.wang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 10:44:08 +01:00
Marc Kleine-Budde
4c3333693f can: m_can: m_can_{read_fifo,echo_tx_event}(): shift timestamp to full 32 bits
In commit 1be37d3b04 ("can: m_can: fix periph RX path: use
rx-offload to ensure skbs are sent from softirq context") the RX path
for peripheral devices was switched to RX-offload.

Received CAN frames are pushed to RX-offload together with a
timestamp. RX-offload is designed to handle overflows of the timestamp
correctly, if 32 bit timestamps are provided.

The timestamps of m_can core are only 16 bits wide. So this patch
shifts them to full 32 bit before passing them to RX-offload.

Link: https://lore.kernel.org/all/20220612211410.4081390-1-mkl@pengutronix.de
Fixes: 1be37d3b04 ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context")
Cc: <stable@vger.kernel.org> # 5.13
Cc: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Reviewed-by: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-04 11:43:00 +02:00
Marc Kleine-Budde
5b12933de4 can: m_can: m_can_chip_config(): actually enable internal timestamping
In commit df06fd6782 ("can: m_can: m_can_chip_config(): enable and
configure internal timestamps") the timestamping in the m_can core
should be enabled. In peripheral mode, the RX'ed CAN frames, TX
compete frames and error events are sorted by the timestamp.

The above mentioned commit however forgot to enable the timestamping.
Add the missing bits to enable the timestamp counter to the write of
the Timestamp Counter Configuration register.

Link: https://lore.kernel.org/all/20220612212708.4081756-1-mkl@pengutronix.de
Fixes: df06fd6782 ("can: m_can: m_can_chip_config(): enable and configure internal timestamps")
Cc: <stable@vger.kernel.org> # 5.13
Cc: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Reviewed-by: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-04 11:42:59 +02:00
Liang He
562fed945e can: grcan: grcan_probe(): remove extra of_node_get()
In grcan_probe(), of_find_node_by_path() has already increased the
refcount. There is no need to call of_node_get() again, so remove it.

Link: https://lore.kernel.org/all/20220619070257.4067022-1-windhl@126.com
Fixes: 1e93ed26ac ("can: grcan: grcan_probe(): fix broken system id check for errata workaround needs")
Cc: stable@vger.kernel.org # v5.18
Cc: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-04 11:42:59 +02:00
Rhett Aultman
2bda24ef95 can: gs_usb: gs_usb_open/close(): fix memory leak
The gs_usb driver appears to suffer from a malady common to many USB
CAN adapter drivers in that it performs usb_alloc_coherent() to
allocate a number of USB request blocks (URBs) for RX, and then later
relies on usb_kill_anchored_urbs() to free them, but this doesn't
actually free them. As a result, this may be leaking DMA memory that's
been used by the driver.

This commit is an adaptation of the techniques found in the esd_usb2
driver where a similar design pattern led to a memory leak. It
explicitly frees the RX URBs and their DMA memory via a call to
usb_free_coherent(). Since the RX URBs were allocated in the
gs_can_open(), we remove them in gs_can_close() rather than in the
disconnect function as was done in esd_usb2.

For more information, see the 928150fad4 ("can: esd_usb2: fix memory
leak").

Link: https://lore.kernel.org/all/alpine.DEB.2.22.394.2206031547001.1630869@thelappy
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: stable@vger.kernel.org
Signed-off-by: Rhett Aultman <rhett.aultman@samsara.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-04 11:42:59 +02:00
Duy Nguyen
374e11f1bd can: rcar_canfd: Fix data transmission failed on R-Car V3U
On R-Car V3U, this driver should use suitable register offset instead of
other SoCs' one. Otherwise, data transmission failed on R-Car V3U.

Fixes: 45721c406d ("can: rcar_canfd: Add support for r8a779a0 SoC")
Link: https://lore.kernel.org/all/20220704074611.957191-1-yoshihiro.shimoda.uh@renesas.com
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-04 11:42:59 +02:00
David S. Miller
5ee4bba272 Merge branch 'smsc95xx-deadlock'
Lukas Wunner says:

====================
Deadlock no more in LAN95xx

Second attempt at fixing a runtime resume deadlock in the LAN95xx USB driver:

In short, the driver isn't using the "nopm" register accessors in portions
of its runtime resume path, causing a deadlock.  I'm fixing that by
auto-detecting whether nopm accessors shall be used, instead of
having to explicitly call them wherever it's necessary.
As a byproduct, code size shrinks significantly (see diffstat below).

Back in April I submitted a first attempt which was rejected by Alan Stern:
https://lore.kernel.org/all/6710d8c18ff54139cdc538763ba544187c5a0cee.1651041411.git.lukas@wunner.de/

That approach only detected whether a PM callback is running concurrently,
not whether the access is performed by the PM callback.  I've come up with
a different approach which should resolve the objection (see patch [1/3]).
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 10:39:25 +01:00
Lukas Wunner
03b3df43ce usbnet: smsc95xx: Clean up unnecessary BUG_ON() upon register access
smsc95xx_read_reg() and smsc95xx_write_reg() call BUG_ON() if the
struct usbnet pointer passed in is NULL.

The functions have just been amended to dereference the pointer on
entry.  So the kernel now oopses if the pointer is NULL, eliminating
the need for an explicit BUG_ON().

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 10:39:25 +01:00
Lukas Wunner
3147242980 usbnet: smsc95xx: Clean up nopm handling
The LAN95xx driver has just been amended to auto-detect whether the
_nopm variant of usbnet_read_cmd() / usbnet_write_cmd() shall be used.

Drop all the now unnecessary open coding of that distinction.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 10:39:25 +01:00
Lukas Wunner
7b960c967f usbnet: smsc95xx: Fix deadlock on runtime resume
Commit 05b35e7eb9 ("smsc95xx: add phylib support") amended
smsc95xx_resume() to call phy_init_hw().  That function waits for the
device to runtime resume even though it is placed in the runtime resume
path, causing a deadlock.

The problem is that phy_init_hw() calls down to smsc95xx_mdiobus_read(),
which never uses the _nopm variant of usbnet_read_cmd().

Commit b4df480f68 ("usbnet: smsc95xx: add reset_resume function with
reset operation") causes a similar deadlock on resume if the device was
already runtime suspended when entering system sleep:

That's because the commit introduced smsc95xx_reset_resume(), which
calls down to smsc95xx_reset(), which neglects to use _nopm accessors.

Fix by auto-detecting whether a device access is performed by the
suspend/resume task_struct and use the _nopm variant if so.  This works
because the PM core guarantees that suspend/resume callbacks are run in
task context.

Stacktrace for posterity:

  INFO: task kworker/2:1:49 blocked for more than 122 seconds.
  Workqueue: usb_hub_wq hub_event
  schedule
  rpm_resume
  __pm_runtime_resume
  usb_autopm_get_interface
  usbnet_read_cmd
  __smsc95xx_read_reg
  __smsc95xx_phy_wait_not_busy
  __smsc95xx_mdio_read
  smsc95xx_mdiobus_read
  __mdiobus_read
  mdiobus_read
  smsc_phy_reset
  phy_init_hw
  smsc95xx_resume
  usb_resume_interface
  usb_resume_both
  usb_runtime_resume
  __rpm_callback
  rpm_callback
  rpm_resume
  __pm_runtime_resume
  usb_autoresume_device
  hub_event
  process_one_work

Fixes: b4df480f68 ("usbnet: smsc95xx: add reset_resume function with reset operation")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.16+
Cc: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 10:39:25 +01:00
Kurt Kanzenbach
39bfb3c12d net: phy: broadcom: Add support for BCM53128 internal PHYs
Add support for BCM53128 internal PHYs. These support interrupts as well as
statistics. Therefore, enable the Broadcom PHY driver for them.

Tested on BCM53128 switch using the mainline b53 DSA driver.

Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 10:33:06 +01:00
Clément Léger
326569cc33 dt-bindings: net: dsa: renesas,rzn1-a5psw: add interrupts description
Describe the switch interrupts (dlr, switch, prp, hub, pattern) which
are connected to the GIC.

Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 10:32:24 +01:00
Casper Andersson
0d153dd208 selftest: net: bridge mdb add/del entry to port that is down
Tests that permanent mdb entries can be added/deleted on ports with state down.

Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 10:30:06 +01:00
XueBing Chen
634b215b73 net: ipconfig: use strscpy to replace strlcpy
The strlcpy should not be used because it doesn't limit the source
length. Preferred is strscpy.

Signed-off-by: XueBing Chen <chenxuebing@jari.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 10:28:00 +01:00
Srinivas Neeli
c6da4590fe Revert "can: xilinx_can: Limit CANFD brp to 2"
This reverts commit 05ca14fdb6.

On early silicon engineering samples observed bit shrinking issue when
we use brp as 1. Hence updated brp_min as 2. As in production silicon
this issue is fixed, so reverting the patch.

Link: https://lore.kernel.org/all/20220609082433.1191060-2-srinivas.neeli@xilinx.com
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-04 11:24:13 +02:00
David S. Miller
ea1c3b77bc Merge branch 'netdev-docs'
Jakub Kicinski says:

====================
docs: netdev: document more of our rules

The patch series length limit and reverse xmas tree are not documented.
Add those, and a tl;dr section summarizing how we differ.

v2: improve the series length blurb (Andrew)
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 10:06:50 +01:00
Jakub Kicinski
5d407ca738 docs: netdev: add a cheat sheet for the rules
Summarize the rules we see broken most often and which may
be less familiar to kernel devs who are used to working outside
of netdev.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 10:06:50 +01:00
Jakub Kicinski
a248756411 docs: netdev: document reverse xmas tree
Similarly to the 15 patch rule the reverse xmas tree is not
documented.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 10:06:50 +01:00
Jakub Kicinski
02514a067f docs: netdev: document that patch series length limit
We had been asking people to avoid massive patch series but it does
not appear in the FAQ.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 10:06:50 +01:00
David S. Miller
798661c736 Merge branch 'mlxsw-unified-bridge-conversion-part-6'
Ido Schimmel says:

====================
mlxsw: Unified bridge conversion - part 6/6

This is the sixth and final part of the conversion of mlxsw to the
unified bridge model. It transitions the last bits of functionality that
were under firmware's responsibility in the legacy model to the driver.
The last patches flip the driver to the unified bridge model and clean
up code that was used to make the conversion easier to review.

Patchset overview:

Patch #1 sets the egress VID for known unicast packets. For multicast
packets, the egress VID is configured using the MPE table. See commit
8c2da081c8 ("mlxsw: spectrum_fid: Configure egress VID classification
for multicast").

Patch #2 configures the VNI to FID classification that is used during
decapsulation.

Patch #3 configures ingress router interface (RIF) in FID classification
records, so that when a packet reaches the router block, its ingress RIF
is known. Care is taken to configure this in all the different flows
(e.g., RIF set on a FID, {Port, VID} joins a FID that already has a RIF
etc.).

Patch #4 configures the egress VID for routed packets. For such packets,
the egress VID is not set by the MPE table or by an FDB record at the
egress bridge, but instead by a dedicated table that maps {Egress RIF,
Egress port} to a VID.

Patch #5 removes VID configuration from RIF creation as in the unified
bridge model firmware no longer needs it.

Patch #6 sets the egress FID to use in RIF configuration so that the
device knows using which FID to bridge the packet after routing.

Patches #7-#9 add a new 802.1Q family and associated VLAN RIFs. In the
unified bridge model, we no longer need to emulate 802.1Q FIDs using
802.1D FIDs as VNI can be associated with both.

Patches #10-#11 finally flip the driver to the unified bridge model.

Patches #12-#13 clean up code that was used to make the conversion
easier to review.

v2:
* Fix build failure [1] in patch #1.

[1] https://lore.kernel.org/netdev/20220630201709.6e66a1bb@kernel.org/
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 09:56:58 +01:00
Amit Cohen
88840d697f mlxsw: spectrum_fid: Remove '_ub_' indication from structures and defines
Some structures and defines were added with '_ub_' indication, as there
were equivalent objects for the legacy model.

Now when the legacy model is not used anymore, remove the '_ub_'
indication.

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 09:56:57 +01:00
Amit Cohen
8928fd4778 mlxsw: spectrum_fid: Remove flood_index() from FID operation structure
The flood_index() function is not needed anymore, as in the unified
bridge model the flood index is calculated using 'mid_base' and
'fid_offset'.

Remove this function.

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 09:56:57 +01:00
Amit Cohen
77b7f83d5c mlxsw: Enable unified bridge model
After all the preparations for unified bridge model, finally flip mlxsw
driver to use the new model.

Change config profile, set 'ubridge' to true and remove the configurations
that are relevant only for the legacy model. Set 'flood_mode' to
'controlled' as the current mode is not supported with unified bridge
model.

Remove all the code which is dedicated to the legacy model. Remove
'struct mlxsw_sp.ubridge' variable which was temporarily added to separate
configurations between the models.

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 09:56:57 +01:00
Amit Cohen
e9cf8990fa mlxsw: Add ubridge to config profile
The unified bridge model is enabled via the CONFIG_PROFILE command
during driver initialization. Add the definition of the relevant fields
to the command's payload in preparation for unified bridge enablement.

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 09:56:57 +01:00
Amit Cohen
bf73904f5f mlxsw: Add support for 802.1Q FID family
Using the legacy bridge model, there is no VID classification at egress
for 802.1Q FIDs, which means that the VID is maintained.

This behavior cause the limitation that 802.1Q FIDs cannot work with VXLAN.
This limitation stems from the fact that a decapsulated VXLAN packet should
not contain a VLAN tag. If such a packet was to egress from a local port
using a 802.1Q FID, it would "maintain" its VLAN on egress, which is no
VLAN at all.

Currently 802.1Q FIDs are emulated in mlxsw driver using 802.1D FIDs. Using
unified bridge model, there is a FID->VID mapping, so it is possible to
stop emulating 802.1Q FIDs.

The main changes are:
1. Use 'SFGC.bridge_type' = 0, to separate between 802.1Q FIDs and
   802.1D FIDs.
2. Use VLAN RIF instead of the emulated one (VLAN_EMU which is emulated
   using FID RIF).
3. Create VID->FID mapping when the FID is created. Then when a new port
   is mapped to the FID, if it not in virtual mode, no new mapping is
   needed. Save the new port in 'port_vid_list', to be able to update a
   RIF in all {Port, VID}->FID mappings in case that the port will be in
   virtual mode later.
4. Add a dedicated operation function per FID family to update RIF for
   VID->FID mappings. For 802.1d and rFID families, just return. For
   802.1q family, handle the global mapping which is created for new 802.1q
   FID.

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 09:56:57 +01:00
Amit Cohen
d4324e3194 mlxsw: Add new FID families for unified bridge model
In the unified bridge model, mlxsw will no longer emulate 802.1Q FIDs
using 802.1D FIDs. The new FID table will look as follows:

     +---------------+
     | 802.1q FIDs   | 4K entries
     | [1..4094]     |
     +---------------+
     | 802.1d FIDs   | 1K entries
     | [4095..5118]  |
     +---------------+
     | Dummy FIDs    | 1 entry
     | [5119..5119]  |
     +---------------+
     | rFIDs         | 11K entries
     | [5120..16383] |
     +---------------+

In order to make the change easier to review, four new temporary FID
families will be added (e.g., MLXSW_SP_FID_TYPE_8021D_UB) and will not
be registered with the FID core until mlxsw is flipped to use the unified
bridge model.

Add .1d, rfid and dummy FID families for unified bridge, the next patch
will add .1q family separately as it requires more changes.

The following changes are required:
1. Add 'smpe_index_valid' field to 'struct mlxsw_sp_fid_family' and set
   SFMR.smpe accordingly. SMPE index is reserved for rFIDs, as their
   flooding is handled by firmware, and always reserved in Spectrum-1,
   as it is configured as part of PGT table.

2. Add 'ubridge' field to 'struct mlxsw_sp_fid_family'. This field will
   be removed later, use it in mlxsw_sp_fid_family_{register,unregister}()
   to skip the registration / unregistration of the new families when the
   legacy model is used.

3. Indexes - the start and end indexes of each FID family will need to be
   changed according to the above diagram.

4. Add flood tables for unified bridge model, use 'fid_offset' as table
   type, as in the new model the access to flood tables will be using
   'fid_offset' calculation.

5. FID family operation changes:
   a. rFID supposed to be created using SFMR, as it is not created by
      firmware using unified bridge model.
   b. port_vid_map() should perform SVFA for rFID, as the mapping is not
      created by firmware using unified bridge model.
   c. flood_index() is not aligned to the new model, as this function will
      be removed later.

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 09:56:57 +01:00
Amit Cohen
662761d898 mlxsw: Add support for VLAN RIFs
Router interfaces (RIFs) constructed on top of VLAN-aware bridges are of
'VLAN' type, whereas RIFs constructed on top of VLAN-unaware bridges are of
'FID' type.

Currently 802.1Q FIDs are emulated using 802.1D FIDs, therefore VLAN RIFs
are emulated using FID RIFs. As part of converting the driver to use
unified bridge model, 802.1Q FIDs and VLAN RIFs will be used.

The egress FID is required for VLAN RIFs in Spectrum-2 and above, but not
in Spectrum-1, as in Spectrum-1 the mapping for VLAN RIFs is VID->FID,
while in other ASICs it is FID->FID. The reason for the change is that it
is more scalable to reuse the FID->FID entry than creating multiple
{Port, VID}->FID entries for the router port. Use the existing operation
structure to separate the configuration between different ASICs.

Add support for VLAN RIFs, most of the configurations are same to FID
RIFs.

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 09:56:57 +01:00
Amit Cohen
058de325a4 mlxsw: Configure egress FID classification after routing
After routing, a packet needs to perform an L2 lookup using the DMAC it got
from the routing and a FID. In unified bridge model, the egress FID
configuration needs to be performed by software.

It is configured by RITR for both sub-port RIFs and FID RIFs. Currently
FID RIFs already configure eFID. Add eFID configuration for sub-port RIFs.

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 09:56:57 +01:00
Amit Cohen
2c3ae763eb mlxsw: spectrum_router: Do not configure VID for sub-port RIFs
The field 'vid' in RITR is reserved when unified bridge model is used
and the RIF's type is sub-port RIF. Instead, ingress VID is configured via
SVFA and egress VID is configured via REIV.

Set 'vid' to zero in RITR register for sub-port RIF when unified bridge
model is used.

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 09:56:57 +01:00
Amit Cohen
d4b464d20b mlxsw: spectrum_fid: Configure layer 3 egress VID classification
After routing, the device always consults a table that determines the
packet's egress VID based on {egress RIF, egress local port}. In the
unified bridge model, it is up to software to maintain this table via REIV
register.

The table needs to be updated in the following flows:
1. When a RIF is set on a FID, need to iterate over the FID's {Port, VID}
   list and issue REIV write to map the {RIF, Port} to the given VID.
2. When a {Port, VID} is mapped to a FID and the FID already has a RIF,
   need to issue REIV write with a single record to map the {RIF, Port}
   to the given VID.

REIV register supports a simultaneous update of 256 ports, so use this
capability for the first flow.

Handle the two above mentioned flows.

Add mlxsw_sp_fid_evid_map() function to handle egress VID classification
for both unicast and multicast. Layer 2 multicast configuration is already
done in the driver, just move it to the new function.

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 09:56:57 +01:00
Amit Cohen
fea20547d5 mlxsw: Configure ingress RIF classification
Before layer 2 forwarding, the device classifies an incoming packet to
a FID. The classification is done based on one of the following keys:

1. FID
2. VNI (after decapsulation)
3. VID / {Port, VID}

After classification, the FID is known, but also all the attributes of
the FID, such as the router interface (RIF) via which a packet that
needs to be routed will ingress the router block.

In the legacy model, when a RIF was created / destroyed, it was
firmware's responsibility to update it in the previously mentioned FID
classification records. In the unified bridge model, this responsibility
moved to software.

The third classification requires to iterate over the FID's {Port, VID}
list and issue SVFA write with the correct mapping table according to the
port's mode (virtual or not). We never map multiple VLANs to the same FID
using VID->FID mapping, so such a mapping needs to be performed once.

When a new FID classification entry is configured and the FID already has
a RIF, set the RIF as part of SVFA configuration.

The reverse needs to be done when clearing a RIF from a FID. Currently,
clearing is done by issuing mlxsw_sp_fid_rif_set() with a NULL RIF pointer.
Instead, introduce mlxsw_sp_fid_rif_unset().

Note that mlxsw_sp_fid_rif_set() is called after the RIF is fully
operational, so it conforms to the internal requirement regarding
SVFA.irif_v: "Must not be set for a non-enabled RIF".

Do not set the ingress RIF for rFIDs, as the {Port, VID}->rFID entry is
configured by firmware when legacy model is used, a next patch will
handle this configuration for rFIDs and unified bridge model.

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 09:56:57 +01:00
Amit Cohen
8cfc7f7707 mlxsw: spectrum_fid: Configure VNI to FID classification
In the new model, SFMR no longer configures both VNI->FID and FID->VNI
classifications, but only the later. The former needs to be configured via
SVFA.

Add SVFA configuration as part of vni_set() and vni_clear().

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 09:56:57 +01:00
Amit Cohen
53d7ae53d8 mlxsw: Configure egress VID for unicast FDB entries
Using unified bridge model, firmware no longer configures the egress VID
"under the hood" and moves this responsibility to software.

For layer 2, this means that software needs to determine the egress VID
for both unicast (i.e., FDB) and multicast (i.e., MDB and flooding) flows.

Unicast FDB records and unicast LAG FDB records have new fields - "set_vid"
and "vid", set them. For records which point to router port, do not set
these fields.

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-07-04 09:56:57 +01:00
Oliver Hartkopp
f1b4e32aca can: bcm: use call_rcu() instead of costly synchronize_rcu()
In commit d5f9023fa6 ("can: bcm: delay release of struct bcm_op
after synchronize_rcu()") Thadeu Lima de Souza Cascardo introduced two
synchronize_rcu() calls in bcm_release() (only once at socket close)
and in bcm_delete_rx_op() (called on removal of each single bcm_op).

Unfortunately this slow removal of the bcm_op's affects user space
applications like cansniffer where the modification of a filter
removes 2048 bcm_op's which blocks the cansniffer application for
40(!) seconds.

In commit 181d444790 ("can: gw: use call_rcu() instead of costly
synchronize_rcu()") Eric Dumazet replaced the synchronize_rcu() calls
with several call_rcu()'s to safely remove the data structures after
the removal of CAN ID subscriptions with can_rx_unregister() calls.

This patch adopts Erics approach for the can-bcm which should be
applicable since the removal of tasklet_kill() in bcm_remove_op() and
the introduction of the HRTIMER_MODE_SOFT timer handling in Linux 5.4.

Fixes: d5f9023fa6 ("can: bcm: delay release of struct bcm_op after synchronize_rcu()") # >= 5.4
Link: https://lore.kernel.org/all/20220520183239.19111-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
Cc: Eric Dumazet <edumazet@google.com>
Cc: Norbert Slusarek <nslusarek@gmx.net>
Cc: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-04 10:33:39 +02:00
Thomas Hellström
1926a6b759 drm/i915: Fix vm use-after-free in vma destruction
In vma destruction, the following race may occur:

Thread 1:	    		  Thread 2:
i915_vma_destroy();

  ...
  list_del_init(vma->vm_link);
  ...
  mutex_unlock(vma->vm->mutex);
				  __i915_vm_release();
release_references();

And in release_reference() we dereference vma->vm to get to the
vm gt pointer, leading to a use-after free.

However, __i915_vm_release() grabs the vm->mutex so the vm won't be
destroyed before vma->vm->mutex is released, so extract the gt pointer
under the vm->mutex to avoid the vma->vm dereference in
release_references().

v2: Fix a typo in the commit message (Andi Shyti)

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5944
Fixes: e1a7ab4fca ("drm/i915: Remove the vm open count")

Cc: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Acked-by: Nirmoy Das <nirmoy.das@intel.con>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220620123659.381772-1-thomas.hellstrom@linux.intel.com
2022-07-04 10:25:50 +02:00
Petr Vaněk
5e25c25aa2 xfrm: improve wording of comment above XFRM_OFFLOAD flags
I have noticed a few minor wording issues in a comment recently added
above XFRM_OFFLOAD flags in 7c76ecd9c9 ("xfrm: enforce validity of
offload input flags").

Signed-off-by: Petr Vaněk <arkamar@atlas.cz>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2022-07-04 10:20:11 +02:00
Zhang Jiaming
cf746bac6c esp6: Fix spelling mistake
Change 'accomodate' to 'accommodate'.

Signed-off-by: Zhang Jiaming <jiaming@nfschina.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2022-07-04 10:20:11 +02:00