No issues have been reported yet for DMIC audio level on ps platforms,
but as problems were found both on YC (Rembrandt) and Renoir based
designs it's very likely they happen on ps too.
Increase the PDM gain to solve this problem.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230131184653.10216-6-mario.limonciello@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of regressions for any users that the new pdm_gain value is
too high and for additional debugging, introduce a module parameter
that would let them configure it.
This parameter should be removed in the future:
* If it's determined that the parameter is not needed, just hardcode
the correct value as before
* If users do end up using it to debug and report different values
we should introduce a config knob that can have policy set by ucm.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230131184653.10216-5-mario.limonciello@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A similar issue that was reported on Rembrandt based laptops with
low DMIC volume is also being reported for Barcelo based laptops
that use renoir acp3x.
Increase the PDM gain to overcome this problem.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230131184653.10216-4-mario.limonciello@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of regressions for any users that the new pdm_gain value is
too high and for additional debugging, introduce a module parameter
that would let them configure it.
This parameter should be removed in the future:
* If it's determined that the parameter is not needed, just hardcode
the correct value as before
* If users do end up using it to debug and report different values
we should introduce a config knob that can have policy set by ucm.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230131184653.10216-3-mario.limonciello@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A number of users for Lenovo Rembrandt based laptops are
reporting that the microphone is too quiet relative to
Windows with a dual boot.
Increase the PDM gain to overcome this problem.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230131184653.10216-2-mario.limonciello@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 2dc0b46b5e ("libata: sata_down_spd_limit should return if
driver has not recorded sstatus speed") changed the behavior of
sata_down_spd_limit() to return doing nothing if a drive does not report
a current link speed, to avoid reducing the link speed to the lowest 1.5
Gbps speed.
However, the change assumed that a speed was recorded before probing
(e.g. before a suspend/resume) and set in link->sata_spd. This causes
problems with adapters/drives combination failing to establish a link
speed during probe autonegotiation. One example reported of this problem
is an mvebu adapter with a 3Gbps port-multiplier box: autonegotiation
fails, leaving no recorded link speed and no reported current link
speed. Probe retries also fail as no action is taken by sata_set_spd()
after each retry.
Fix this by returning early in sata_down_spd_limit() only if we do have
a recorded link speed, that is, if link->sata_spd is not 0. With this
fix, a failed probe not leading to a recorded link speed is retried at
the lower 1.5 Gbps speed, with the link speed potentially increased
later on the second revalidate of the device if the device reports
that it supports higher link speeds.
Reported-by: Marius Dinu <marius@psihoexpert.ro>
Fixes: 2dc0b46b5e ("libata: sata_down_spd_limit should return if driver has not recorded sstatus speed")
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Marius Dinu <marius@psihoexpert.ro>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Using the control_unload for graph type of elem will lead surprises on
module unload.
The correct callback to use is the dapm_route_unload.
Fixes: 31e9273912 ("ASoC: topology: Use unload() op directly")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230201112846.27707-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The conversion to use generic helpers missed the else for the dai
direction check which leads to failure when loading playback widgets
Fixes: 323f09a61d ("ASoC: sof: use helper function")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20230201112846.27707-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The linux/net_tstamp.h is included more than once, thus clean it up.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/202301311440516312161@zte.com.cn
The hvcs driver only ever gets two references to the port. One
at initialization time, and one at install time. Remove the code
that was trying to do multiple port puts for each open, which
would result in more puts than gets.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20230201195743.303163-2-brking@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only need to consume TX completion instead of refilling 'fill' ring.
It's currently not an issue because we never RX more than 8 packets.
Fixes: e2a46d54d7 ("selftests/bpf: Verify xdp_metadata xdp->af_xdp path")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230201233640.367646-1-sdf@google.com
Commit b8a926bea8 ("kunit: Introduce KUNIT_EXPECT_MEMEQ and
KUNIT_EXPECT_MEMNEQ macros") introduced a new macro to compare blocks of
memory and, if the test fails, print the result in a human-friendly
format. Therefore, use KUNIT_EXPECT_MEMEQ to compare memory blocks in
replacement of the KUNIT_EXPECT_EQ macro.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: David Gow <davidgow@google.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130125554.363481-1-mairacanal@riseup.net
Commit 41b7a347bf ("powerpc: Book3S 64-bit outline-only KASAN
support") added a select of ARCH_WANTS_NO_INSTR, because it also added
some uses of noinstr. However noinstr is always defined, regardless of
ARCH_WANTS_NO_INSTR, so there's no need to select it just for that.
As PeterZ says [1]:
Note that by selecting ARCH_WANTS_NO_INSTR you effectively state to
abide by its rules.
As of now the powerpc code does not abide by those rules, and trips some
new warnings added by Peter in linux-next.
So until the code can be fixed to avoid those warnings, disable
ARCH_WANTS_NO_INSTR.
Note that ARCH_WANTS_NO_INSTR is also used to gate building KCOV and
parts of KCSAN. However none of the noinstr annotations in powerpc were
added for KCOV or KCSAN, instead instrumentation is blocked at the file
level using KCOV_INSTRUMENT_foo.o := n.
[1]: https://lore.kernel.org/linuxppc-dev/Y9t6yoafrO5YqVgM@hirez.programming.kicks-ass.net
Reported-by: Sachin Sant <sachinp@linux.ibm.com>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The f_uvc code includes an interrupt endpoint against the VideoControl
interface. According to section 2.4.2 of the UVC specification however
this endpoint is optional in at least some cases:
"This endpoint is optional, but may be mandatory under certain
conditions"
The conditions enumerated are whether...
1. The device supports hardware triggers
2. The device implements any AutoUpdate controls
3. The device implements any Asynchronous controls
As all of those things are implementation dependent, this endpoint
might be unnecessary for some users. Further to that it is unusable
in the current implementation as there is no mechanism within the
UVC gadget driver that allows data to be sent over that endpoint.
Disable the interrupt endpoint by default, but check whether the
user has asked for it to be enabled in configfs and continue to
generate it if so.
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230130105045.120886-4-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new attribute to the default control config group that allows
users to specify whether they want to enable the optional interrupt
endpoint for the VideoControl interface.
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230130105045.120886-3-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The f_uvc code defines an endpoint named "uvc_control_ep" but it
is configured with a non-zero endpoint address and has its
bmAttributes flagged as USB_ENDPOINT_XFER_INT - this cannot be the
VideoControl interface's control endpoint, as the default endpoint
0 is used for that purpose. This is instead the optional interrupt
endpoint that can be contained by a VideoControl interface. There
is also a Class-specific VC Interrupt Endpoint Descriptor and a
SuperSpeed companion descriptor that are also for the VC interface's
interrupt endpoint but are named as though they are for the control
endpoint.
Rename the variables to make that clear.
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230130105045.120886-2-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable the TYPEC UCSI support and the Cypress UCSI driver that is used
on the NVIDIA Jetson platforms.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230131175748.256423-7-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now the Cypress CCG driver has been updated to support the
'firmware-name' property to align with device-tree, remove the
'ccgx,firmware-build' property as this is no longer needed.
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ajay Gupta <ajayg@nvidia.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20230131175748.256423-5-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device-tree support for the Cypress CCG UCSI driver. The device-tree
binding for the Cypress CCG device uses the standard device-tree
'firmware-name' string property to indicate the firmware build that is
used.
The NVIDIA GPU I2C driver has been updated to use an ACPI string
property that is also named 'firmware-build' and given that this was the
only users of the 'ccgx,firmware-build' property, we can now remove
support for this legacy property.
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Co-developed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230131175748.256423-4-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device-tree uses the 'firmware-name' string property to pass a name of
the firmware build to the Cypress CCGx driver. Add a new ACPI string
property to the NVIDIA GPU I2C driver to align with device-tree so that
we can migrate to using a common property name for both ACPI and
device-tree.
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Co-developed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Ajay Gupta <ajayg@nvidia.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20230131175748.256423-3-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During enumeration or composition switch,a userspace process
agnostic of the conventions of configs can try to create function
symlinks even after the UDC is bound to current config which is
not correct. Potentially it can create duplicates within the
current config.
Prevent this by adding a check if udc_name already exists, then bail
out of cfg_link.
Following is an example:
Step1:
ln -s X1 ffs.a
-->cfg_link
--> usb_get_function(ffs.a)
->ffs_alloc
CFG->FUNC_LIST: <ffs.a>
C->FUNCTION: <empty>
Step2:
echo udc.name > /config/usb_gadget/g1/UDC
--> UDC_store
->composite_bind
->usb_add_function
CFG->FUNC_LIST: <empty>
C->FUNCTION: <ffs.a>
Step3:
ln -s Y1 ffs.a
-->cfg_link
-->usb_get_function(ffs.a)
->ffs_alloc
CFG->FUNC_LIST: <ffs.a>
C->FUNCTION: <ffs.a>
both the lists corresponds to the same function instance ffs.a
but the usb_function* pointer is different because in step 3
ffs_alloc has created a new reference to usb_function* for
ffs.a and added it to cfg_list.
Step4:
Now a composition switch involving <ffs.b,ffs.a> is executed.
the composition switch will involve 3 things:
1. unlinking the previous functions existing
2. creating new symlinks
3. writing UDC
However, the composition switch is generally taken care by
userspace process which creates the symlinks in its own
nomenclature(X*) and removes only those.
So it won't be able to remove Y1 which user had created
by own.
Due to this the new symlinks cannot be created for ffs.a
since the entry already exists in CFG->FUNC_LIST.
The state of the CFG->FUNC_LIST is as follows:
CFG->FUNC_LIST: <ffs.a>
Fixes: 88af8bbe4e ("usb: gadget: the start of the configfs interface")
Signed-off-by: Krishna Kurapati PSSNV <quic_kriskura@quicinc.com>
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Link: https://lore.kernel.org/r/20230201132308.31523-1-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the probe routine explicitly compares the compatible string of
the device node to figure out which features and quirks a certain
Allwinner MUSB model requires. This gets harder to maintain for new
SoCs.
Add a struct sunxi_musb_cfg that names the features and quirks
explicitly, and create instances of this struct for every type of MUSB
device we support. Then bind this to the compatible strings via the OF
data feature.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230201105348.1815461-4-andre.przywara@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The suniv SoC has a MUSB controller like the one in A33, but with a SRAM
region to be claimed.
Add support for it.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20230201105348.1815461-3-andre.przywara@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allwinner F1C100s has a hybrid MUSB controller between the A10 one and
the A33 one.
Add a compatible string for it.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20230201105348.1815461-2-andre.przywara@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB_XHCI_RZV2M and USB_RENESAS_USB3 select other drivers
based on the enabled SoC types, which leads to build failures
when the dependencies are not met:
WARNING: unmet direct dependencies detected for USB_RZV2M_USB3DRD
Depends on [n]: USB_SUPPORT [=y] && USB_GADGET [=n] && (ARCH_R9A09G011 [=n] || COMPILE_TEST [=y])
Selected by [m]:
- USB_XHCI_RZV2M [=m] && USB_SUPPORT [=y] && USB [=y] && USB_XHCI_HCD [=m] && USB_XHCI_PLATFORM [=m] && (ARCH_R9A09G011 [=n] || COMPILE_TEST [=y])
ERROR: modpost: "rzv2m_usb3drd_reset" [drivers/usb/host/xhci-plat-hcd.ko] undefined!
The xhci-rcar driver has a reverse dependency with the xhci core, and it
depends on the UDC driver in turn. To untangle this, make the xhci-rcar.ko
driver a standalone module that just calls into the xhci-plat.ko module
like other drivers do.
This allows handling the dependency on the USB_RZV2M_USB3DRD driver to
only affect the xhci-rcar module and simplify the xhci-plat module.
It also allows leaving out the hacks for broken dma mask and nested
devices from the rcar side and keep that only in the generic xhci driver.
As a future cleanup, the marvell and dwc3 specific bits of xhci-plat.c
could be moved out as well, but that is not required for this bugfix.
Fixes: c52c9acc41 ("xhci: host: Add Renesas RZ/V2M SoC support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230131150531.12347-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function only calls mtk_otg_switch_init() when the ->port_mode
is MUSB_OTG so the clean up code should only call mtk_otg_switch_exit()
for that mode.
Fixes: 0990366bab ("usb: musb: Add support for MediaTek musb controller")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/Y8/3TqpqiSr0RxFH@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the a new ring layout is set, the max coalesced frames for RX and
TX are re-calculated, too. Add the missing assignment of the newly
calculated TX max coalesced frames.
Fixes: 656fc12dda ("can: mcp251xfd: add TX IRQ coalescing ethtool support")
Link: https://lore.kernel.org/all/20230130154334.1578518-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The timer for the transmission of isotp PDUs formerly had two functions:
1. send two consecutive frames with a given time gap
2. monitor the timeouts for flow control frames and the echo frames
This led to larger txstate checks and potentially to a problem discovered
by syzbot which enabled the panic_on_warn feature while testing.
The former 'txtimer' function is split into 'txfrtimer' and 'txtimer'
to handle the two above functionalities with separate timer callbacks.
The two simplified timers now run in one-shot mode and make the state
transitions (especially with isotp_rcv_echo) better understandable.
Fixes: 866337865f ("can: isotp: fix tx state handling for echo tx processing")
Reported-by: syzbot+5aed6c3aaba661f5b917@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org # >= v6.0
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230104145701.2422-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When wait_event_interruptible() has been interrupted by a signal the
tx.state value might not be ISOTP_IDLE. Force the state machines
into idle state to inhibit the timer handlers to continue working.
Fixes: 866337865f ("can: isotp: fix tx state handling for echo tx processing")
Cc: stable@vger.kernel.org
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230112192347.1944-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
A CAN XL device is always capable to process CAN FD frames. The former
check when sending CAN FD frames relied on the existence of a CAN FD
device and did not check for a CAN XL device that would be correct
too.
With this patch the CAN FD feature is enabled automatically when CAN
XL is switched on - and CAN FD cannot be switch off while CAN XL is
enabled.
This precondition also leads to a clean up and reduction of checks in
the hot path in raw_rcv() and raw_sendmsg(). Some conditions are
reordered to handle simple checks first.
changes since v1: https://lore.kernel.org/all/20230131091012.50553-1-socketcan@hartkopp.net
- fixed typo: devive -> device
changes since v2: https://lore.kernel.org/all/20230131091824.51026-1-socketcan@hartkopp.net/
- reorder checks in if statements to handle simple checks first
Fixes: 626332696d ("can: raw: add CAN XL support")
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230131105613.55228-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The conclusion "j1939_session_deactivate() should be called with a
session ref-count of at least 2" is incorrect. In some concurrent
scenarios, j1939_session_deactivate can be called with the session
ref-count less than 2. But there is not any problem because it
will check the session active state before session putting in
j1939_session_deactivate_locked().
Here is the concurrent scenario of the problem reported by syzbot
and my reproduction log.
cpu0 cpu1
j1939_xtp_rx_eoma
j1939_xtp_rx_abort_one
j1939_session_get_by_addr [kref == 2]
j1939_session_get_by_addr [kref == 3]
j1939_session_deactivate [kref == 2]
j1939_session_put [kref == 1]
j1939_session_completed
j1939_session_deactivate
WARN_ON_ONCE(kref < 2)
=====================================================
WARNING: CPU: 1 PID: 21 at net/can/j1939/transport.c:1088 j1939_session_deactivate+0x5f/0x70
CPU: 1 PID: 21 Comm: ksoftirqd/1 Not tainted 5.14.0-rc7+ #32
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1 04/01/2014
RIP: 0010:j1939_session_deactivate+0x5f/0x70
Call Trace:
j1939_session_deactivate_activate_next+0x11/0x28
j1939_xtp_rx_eoma+0x12a/0x180
j1939_tp_recv+0x4a2/0x510
j1939_can_recv+0x226/0x380
can_rcv_filter+0xf8/0x220
can_receive+0x102/0x220
? process_backlog+0xf0/0x2c0
can_rcv+0x53/0xf0
__netif_receive_skb_one_core+0x67/0x90
? process_backlog+0x97/0x2c0
__netif_receive_skb+0x22/0x80
Fixes: 0c71437dd5 ("can: j1939: j1939_session_deactivate(): clarify lifetime of session object")
Reported-by: syzbot+9981a614060dcee6eeca@syzkaller.appspotmail.com
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20210906094200.95868-1-william.xuanziyang@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Before the commit fc274c1e99 ("USB: gadget: Add a new bus for gadgets")
gadget driver.bus was unused. For whatever reason, many UDC drivers set
this field explicitly to NULL in udc_start(). With the newly added gadget
bus, doing this will crash the driver during the attach.
The problem was first reported, fixed and tested with OMAP UDC and g_ether.
Other drivers are changed based on code analysis only.
Fixes: fc274c1e99 ("USB: gadget: Add a new bus for gadgets")
Cc: stable <stable@kernel.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230201220125.GD2415@darkstar.musicnaut.iki.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the pr_fmt() macro to prefix all the output with "devtmpfs: ".
while at it, convert printk(<LEVEL>) to pr_<level>().
Signed-off-by: Longlong Xia <xialonglong1@huawei.com>
Link: https://lore.kernel.org/r/20230202033203.1239239-2-xialonglong1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewing the j loop over num_irqs_per_bank, in the code previous
to the fixes: commit, every j was used. now only when j == 0.
If only j == 0 is used, there is no need for the loop.
Fixes: 2103868047 ("gpio: tegra186: Support multiple interrupts per bank")
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
1. Reduce the time of dsi from LP11 to sending cmd
2. Remove dependency on GEM DMA helper
3. Drop unbalanced obj unref
4. Fix the fallback for mediatek,mt8186-disp-ccorr
5. Fixup for error path.
-----BEGIN PGP SIGNATURE-----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=ZhnI
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 6.3
1. Reduce the time of dsi from LP11 to sending cmd
2. Remove dependency on GEM DMA helper
3. Drop unbalanced obj unref
4. Fix the fallback for mediatek,mt8186-disp-ccorr
5. Fixup for error path.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130125811.2567-1-chunkuang.hu@kernel.org
netvsc_dma_map() and netvsc_dma_unmap() currently check the cp_partial
flag and adjust the page_count so that pagebuf entries for the RNDIS
portion of the message are skipped when it has already been copied into
a send buffer. But this adjustment has already been made by code in
netvsc_send(). The duplicate adjustment causes some pagebuf entries to
not be mapped. In a normal VM, this doesn't break anything because the
mapping doesn’t change the PFN. But in a Confidential VM,
dma_map_single() does bounce buffering and provides a different PFN.
Failing to do the mapping causes the wrong PFN to be passed to Hyper-V,
and various errors ensue.
Fix this by removing the duplicate adjustment in netvsc_dma_map() and
netvsc_dma_unmap().
Fixes: 846da38de0 ("net: netvsc: Add Isolation VM support for netvsc driver")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1675135986-254490-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ip_dev_find() may return NULL and assign it to pdev which is
dereferenced later.
Fix this by checking the return value of ip_dev_find() for NULL
similar to the way it is done with other instances of said function.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 1cab775c3e ("RDMA/cxgb4: Fix LE hash collision bug for passive open connection")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20230201172103.17261-1-n.zhandarovich@fintech.ru
Signed-off-by: Leon Romanovsky <leon@kernel.org>
- Make sure to restore bridge chain order by enabling the drm panel
prepare_prev_first flag of the bridge and panel drivers - tc358764 display
bridge device and Samsung s6e3ha2/s6e63j0x03/s6e8aa0 panel devices.
In case of any boards using Exynos5433 SoC, below Display pipeline could be
configured.
Decon -> MIC -> MIPI-DSI -> Panel
So, this patch series makes sure to enable previous bridge device before
enabling MIPI-DSI device.
-----BEGIN PGP SIGNATURE-----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=L8+N
-----END PGP SIGNATURE-----
Merge tag 'exynos-drm-next-for-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next
One fixup series
- Make sure to restore bridge chain order by enabling the drm panel
prepare_prev_first flag of the bridge and panel drivers - tc358764 display
bridge device and Samsung s6e3ha2/s6e63j0x03/s6e8aa0 panel devices.
In case of any boards using Exynos5433 SoC, below Display pipeline could be
configured.
Decon -> MIC -> MIPI-DSI -> Panel
So, this patch series makes sure to enable previous bridge device before
enabling MIPI-DSI device.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130051055.15340-1-inki.dae@samsung.com
NPC exact match feature is supported only on one silicon
variant, removed debug messages which print that this
feature is not available on all other silicon variants.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230201040301.1034843-1-rkannoth@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the single-buffer xdp is loaded and after xdp_linearize_page()
is called, *num_buf becomes 0 and (*num_buf - 1) may overflow into
a large integer in virtnet_build_xdp_buff_mrg(), resulting in
unexpected packet dropping.
Fixes: ef75cb51f1 ("virtio-net: build xdp_buff with multi buffers")
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20230131085004.98687-1-hengqi@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Exact match feature is only available in CN10K-B.
Unregister exact match devlink entry only for
this silicon variant.
Fixes: 87e4ea29b0 ("octeontx2-af: Debugsfs support for exact match.")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230131061659.1025137-1-rkannoth@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
clang static analysis reports
drivers/net/ethernet/intel/igc/igc_ptp.c:673:3: warning: The left operand of
'+' is a garbage value [core.UndefinedBinaryOperatorResult]
ktime_add_ns(shhwtstamps.hwtstamp, adjust);
^ ~~~~~~~~~~~~~~~~~~~~
igc_ptp_systim_to_hwtstamp() silently returns without setting the hwtstamp
if the mac type is unknown. This should be treated as an error.
Fixes: 81b055205e ("igc: Add support for RX timestamping")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230131215437.1528994-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In netdev common pattern, extack pointer is forwarded to the drivers
to be filled with error message. However, the caller can easily
overwrite the filled message.
Instead of adding multiple "if (!extack->_msg)" checks before any
NL_SET_ERR_MSG() call, which appears after call to the driver, let's
add new macro to common code.
[1] https://lore.kernel.org/all/Y9Irgrgf3uxOjwUm@unreal
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/6993fac557a40a1973dfa0095107c3d03d40bec1.1675171790.git.leon@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When set to zero, the neighbor sysctl proxy_delay value
does not cause an immediate reply for ARP/ND requests
as expected, it instead causes a random delay between
[0, U32_MAX). Looking at this comment from
__get_random_u32_below() explains the reason:
/*
* This function is technically undefined for ceil == 0, and in fact
* for the non-underscored constant version in the header, we build bug
* on that. But for the non-constant case, it's convenient to have that
* evaluate to being a straight call to get_random_u32(), so that
* get_random_u32_inclusive() can work over its whole range without
* undefined behavior.
*/
Added helper function that does not call get_random_u32_below()
if proxy_delay is zero and just uses the current value of
jiffies instead, causing pneigh_enqueue() to respond
immediately.
Also added definition of proxy_delay to ip-sysctl.txt since
it was missing.
Signed-off-by: Brian Haley <haleyb.dev@gmail.com>
Link: https://lore.kernel.org/r/20230130171428.367111-1-haleyb.dev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long says:
====================
net: support ipv4 big tcp
This is similar to the BIG TCP patchset added by Eric for IPv6:
https://lwn.net/Articles/895398/
Different from IPv6, IPv4 tot_len is 16-bit long only, and IPv4 header
doesn't have exthdrs(options) for the BIG TCP packets' length. To make
it simple, as David and Paolo suggested, we set IPv4 tot_len to 0 to
indicate this might be a BIG TCP packet and use skb->len as the real
IPv4 total length.
This will work safely, as all BIG TCP packets are GSO/GRO packets and
processed on the same host as they were created; There is no padding
in GSO/GRO packets, and skb->len - network_offset is exactly the IPv4
packet total length; Also, before implementing the feature, all those
places that may get iph tot_len from BIG TCP packets are taken care
with some new APIs:
Patch 1 adds some APIs for iph tot_len setting and getting, which are
used in all these places where IPv4 BIG TCP packets may reach in Patch
2-7, Patch 8 adds a GSO_TCP tp_status for af_packet users, and Patch 9
add new netlink attributes to make IPv4 BIG TCP independent from IPv6
BIG TCP on configuration, and Patch 10 implements this feature.
Note that the similar change as in Patch 2-6 are also needed for IPv6
BIG TCP packets, and will be addressed in another patchset.
The similar performance test is done for IPv4 BIG TCP with 25Gbit NIC
and 1.5K MTU:
No BIG TCP:
for i in {1..10}; do netperf -t TCP_RR -H 192.168.100.1 -- -r80000,80000 -O MIN_LATENCY,P90_LATENCY,P99_LATENCY,THROUGHPUT|tail -1; done
168 322 337 3776.49
143 236 277 4654.67
128 258 288 4772.83
171 229 278 4645.77
175 228 243 4678.93
149 239 279 4599.86
164 234 268 4606.94
155 276 289 4235.82
180 255 268 4418.95
168 241 249 4417.82
Enable BIG TCP:
ip link set dev ens1f0np0 gro_ipv4_max_size 128000 gso_ipv4_max_size 128000
for i in {1..10}; do netperf -t TCP_RR -H 192.168.100.1 -- -r80000,80000 -O MIN_LATENCY,P90_LATENCY,P99_LATENCY,THROUGHPUT|tail -1; done
161 241 252 4821.73
174 205 217 5098.28
167 208 220 5001.43
164 228 249 4883.98
150 233 249 4914.90
180 233 244 4819.66
154 208 219 5004.92
157 209 247 4999.78
160 218 246 4842.31
174 206 217 5080.99
Thanks for the feedback from Eric and David Ahern.
====================
Link: https://lore.kernel.org/r/cover.1674921359.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similar to Eric's IPv6 BIG TCP, this patch is to enable IPv4 BIG TCP.
Firstly, allow sk->sk_gso_max_size to be set to a value greater than
GSO_LEGACY_MAX_SIZE by not trimming gso_max_size in sk_trim_gso_size()
for IPv4 TCP sockets.
Then on TX path, set IP header tot_len to 0 when skb->len > IP_MAX_MTU
in __ip_local_out() to allow to send BIG TCP packets, and this implies
that skb->len is the length of a IPv4 packet; On RX path, use skb->len
as the length of the IPv4 packet when the IP header tot_len is 0 and
skb->len > IP_MAX_MTU in ip_rcv_core(). As the API iph_set_totlen() and
skb_ip_totlen() are used in __ip_local_out() and ip_rcv_core(), we only
need to update these APIs.
Also in GRO receive, add the check for ETH_P_IP/IPPROTO_TCP, and allows
the merged packet size >= GRO_LEGACY_MAX_SIZE in skb_gro_receive(). In
GRO complete, set IP header tot_len to 0 when the merged packet size
greater than IP_MAX_MTU in iph_set_totlen() so that it can be processed
on RX path.
Note that by checking skb_is_gso_tcp() in API iph_totlen(), it makes
this implementation safe to use iph->len == 0 indicates IPv4 BIG TCP
packets.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch introduces gso_ipv4_max_size and gro_ipv4_max_size
per device and adds netlink attributes for them, so that IPV4
BIG TCP can be guarded by a separate tunable in the next patch.
To not break the old application using "gso/gro_max_size" for
IPv4 GSO packets, this patch updates "gso/gro_ipv4_max_size"
in netif_set_gso/gro_max_size() if the new size isn't greater
than GSO_LEGACY_MAX_SIZE, so that nothing will change even if
userspace doesn't realize the new netlink attributes.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
