idle_bias_on was set because cs42l42 has a "VMID" type pseudo-midrail
supply (named FILT+), and these typically take a long time to charge.
But the driver never enabled pm_runtime so it would never have powered-
down the cs42l42 anyway.
In fact, FILT+ can charge to operating voltage within 12.5 milliseconds
of enabling HP or ADC. This time is already covered by the startup
delay of the HP/ADC.
The datasheet warning about FILT+ taking up to 1 second to charge only
applies in the special cases that either the PLL is started or
DETECT_MODE set to non-zero while both HP and ADC are off. The driver
never does either of these.
Removing idle_bias_on allows the Soundwire host controller to suspend
if there isn't a snd_soc_jack handler registered.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-8-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for using CS42L42 as a SoundWire device.
SoundWire-specifics are kept separate from the I2S implementation as
much as possible, aiming to limit the risk of breaking the I2C+I2S
support.
There are some important differences in the silicon behaviour between
I2S and SoundWire mode that are reflected in the implementation:
- ASP (I2S) most not be used in SoundWire mode because the two interfaces
share pins.
- The SoundWire capture (record) port only supports 1 channel. It does
not have left-to-right duplication like the ASP.
- DP2 can only be prepared if the HP has powered-up. DP1 can only be
prepared if the ADC has powered-up. (This ordering restriction does
not exist for ASPs.) The SoundWire core port-prepare step is
triggered by the DAI-link prepare(). This happens before the
codec DAI prepare() or the DAPM sequence so these cannot be used
to enable HP/ADC. Instead the HP/ADC enable/disable are done during
the port_prep callback.
- The SRCs are an integral part of the audio chain but in silicon their
power control is linked to the ASP. There is no equivalent power link
to SoundWire DPs so the driver must take "manual" control of SRC power.
- The SoundWire control registers occupy the lower part of the SoundWire
address space so cs42l42 registers are offset by 0x8000 (non-paged) in
SoundWire mode.
- Register addresses are 8-bit paged in I2C mode but 16-bit unpaged in
SoundWire.
- Special procedures are needed on register read/writes to (a) ensure
that the previous internal bus transaction has completed, and
(b) handle delayed read results, when the read value could not be
returned within the SoundWire read command.
There are also some differences in driver implementation between I2S
and SoundWire operation:
- CS42L42 I2S does not runtime_suspend, but runtime_suspend/resume support
has been added into the driver in SoundWire mode as the most convenient
way to power-up the bus manager and to handle the unattach_request
condition, though the CS42L42 chip does not itself suspend or resume.
- Intel SoundWire host controllers have a low-power clock-stop mode that
requires resetting all peripherals when resuming. This means that the
interrupt registers will be reset in between the interrupt being
generated and the interrupt being handled, and since the interrupt
status is debounced, these values may not be accurate immediately,
and may cause spurious unplug events before settling.
- As in I2S mode, the PLL is only used while audio is active because
of clocking quirks in the silicon. For SoundWire the cs42l42_pll_config()
is deferred until the DAI prepare(), to allow the cs42l42_bus_config()
callback to set the SCLK.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-7-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Export functions that will be needed by a SoundWire module.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-6-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Setup of the ASP (audio serial port) was being done as a side-effect of
cs42l42_pll_config() and forces a restriction on the ratio of sample_rate
to bit_clock that is invalid for Soundwire.
Move the ASP setup into a dedicated function.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-5-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The chosen clocking configuration must give an internal MCLK (MCLKint)
that is an integer multiple of the sample rate.
On I2S each of the supported bit clock frequencies can only be generated
from one sample rate group (either the 44100 or the 48000) so the code
could use only the bitclock to look up a PLL config.
The relationship between sample rate and bitclock frequency is more
complex on Soundwire and so it is possible to set a frame shape to
generate a bitclock from the "wrong" group. For example 2*147 with a
48000 sample rate would give a bitclock of 14112000 which on I2S
could only be derived from a 44100 sample rate.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-4-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SOFT_RESET_REBOOT register is needed to recover CS42L42 state after
a Soundwire bus reset.
This is required to be set whenever there is severe/hard bus reset.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-3-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, port_prep callback only has commands for PRE_PREP, PREP,
and POST_PREP, which doesn't directly say whether this is for a
prepare or deprepare call. Extend the command list enum to say
whether the call is for prepare or deprepare aswell.
Also remove SDW_OPS_PORT_PREP from sdw_port_prep_ops as this is unused,
and update this enum to be simpler and more consistent with enum
sdw_clk_stop_type.
Note: Currently, the only users of SDW_OPS_PORT_POST_PREP are codec
drivers sound/soc/codecs/wsa881x.c and sound/soc/codecs/wsa883x.c, both
of which seem to assume that POST_PREP only occurs after a prepare,
even though it would also have occurred after a deprepare. Since it
doesn't make sense to mark the port prepared after a deprepare, changing
the enum to separate PORT_DEPREP from PORT_PREP should make the check
for PORT_PREP in those drivers be more logical.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20230127165111.3010960-2-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A previous patch removed unnecessary zeroing of the page registers
after a paged transaction, so now the reset_page_addr callback is
unused and can be removed.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230123164949.245898-3-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Zeroing the page registers at the end of every paged transaction is just
overhead (40% overhead on a 1-register access, 25% on a 4-register
transaction). According to the spec a peripheral that supports paging
should only use the values in the page registers if the address is paged
(address bit 15 set). The core SoundWire code always writes the page
registers at the start of a paged transaction so there will never be a
transaction that uses the stale values from a previous paged transaction.
For peripherals that need large amounts of data to be transferred, for
example firmware or filter coefficients, the overhead of page register
zeroing can become quite significant.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230123164949.245898-2-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The coreboot framebuffer doesn't support transparency, its 'reserved'
bit field is merely padding for byte/word alignment of pixel colors [1].
When trying to match the framebuffer to a simplefb format, the kernel
driver unnecessarily requires the format's transparency bit field to
exactly match this padding, even if the former is zero-width.
Due to a coreboot bug [2] (fixed upstream), some boards misreport the
reserved field's size as equal to its position (0x18 for both on a
'Lick' Chromebook), and the driver fails to probe where it would have
otherwise worked fine with e.g. the a8r8g8b8 or x8r8g8b8 formats.
Remove the transparency comparison with reserved bits. When the
bits-per-pixel and other color components match, transparency will
already be in a subset of the reserved field. Not forcing it to match
reserved bits allows the driver to work on the boards which misreport
the reserved field. It also enables using simplefb formats that don't
have transparency bits, although this doesn't currently happen due to
format support and ordering in linux/platform_data/simplefb.h.
[1] https://review.coreboot.org/plugins/gitiles/coreboot/+/4.19/src/commonlib/include/commonlib/coreboot_tables.h#255
[2] https://review.coreboot.org/plugins/gitiles/coreboot/+/4.13/src/drivers/intel/fsp2_0/graphics.c#82
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Link: https://lore.kernel.org/r/20230122190433.195941-1-alpernebiyasak@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Link: https://lore.kernel.org/r/20230129092357.3143-1-liubo03@inspur.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This set of updates consists only of Kconfig cleanup and changes for the
Counter subsystem. In particular, the Kconfig entries are reorganized to
to alphabetical order, and dependencies added to restrict building
certain drivers (intel-qep, ftm-quaddec, and microchip-tcp-capture) to
systems that support them.
Changes
* counter
- Sort the Kconfig entries alphabetically
* ftm-quaddec
- Depend on the Layerscape SoC
* microchip-tcp-capture
- Add appropriate arch deps for TCP driver
- fix dependency references for config MICROCHIP_TCB_CAPTURE
* intel-qep
- Depend on X86
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSNN83d4NIlKPjon7a1SFbKvhIjKwUCY9j+5AAKCRC1SFbKvhIj
KymOAP9xpRP0xWQEiDAgMBQjIlChfbl+5sGqoPftCNXGZ2PP+QEAlDotFEpGRMQ3
UkC3aNiOA2NzGIHOnKjXrKoJRFblcQs=
=WUbe
-----END PGP SIGNATURE-----
Merge tag 'counter-updates-for-6.3a' of git://git.kernel.org/pub/scm/linux/kernel/git/wbg/counter into char-misc-next
William writes:
First set of Counter updates for the 6.3 cycle
This set of updates consists only of Kconfig cleanup and changes for the
Counter subsystem. In particular, the Kconfig entries are reorganized to
to alphabetical order, and dependencies added to restrict building
certain drivers (intel-qep, ftm-quaddec, and microchip-tcp-capture) to
systems that support them.
Changes
* counter
- Sort the Kconfig entries alphabetically
* ftm-quaddec
- Depend on the Layerscape SoC
* microchip-tcp-capture
- Add appropriate arch deps for TCP driver
- fix dependency references for config MICROCHIP_TCB_CAPTURE
* intel-qep
- Depend on X86
* tag 'counter-updates-for-6.3a' of git://git.kernel.org/pub/scm/linux/kernel/git/wbg/counter:
counter: fix dependency references for config MICROCHIP_TCB_CAPTURE
counter: microchip-tcp-capture: Add appropriate arch deps for TCP driver
counter: ftm-quaddec: Depend on the Layerscape SoC
counter: intel-qep: Depend on X86
counter: Sort the Kconfig entries alphabetically
Correct spelling problems for Documentation/networking/ as reported
by codespell.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Cc: Jiri Pirko <jiri@nvidia.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Link: https://lore.kernel.org/r/20230129231053.20863-5-rdunlap@infradead.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In kernels compiled with CONFIG_PARAVIRT=n, the compiler re-orders the
DR7 read in exc_nmi() to happen before the call to sev_es_ist_enter().
This is problematic when running as an SEV-ES guest because in this
environment the DR7 read might cause a #VC exception, and taking #VC
exceptions is not safe in exc_nmi() before sev_es_ist_enter() has run.
The result is stack recursion if the NMI was caused on the #VC IST
stack, because a subsequent #VC exception in the NMI handler will
overwrite the stack frame of the interrupted #VC handler.
As there are no compiler barriers affecting the ordering of DR7
reads/writes, make the accesses to this register volatile, forbidding
the compiler to re-order them.
[ bp: Massage text, make them volatile too, to make sure some
aggressive compiler optimization pass doesn't discard them. ]
Fixes: 315562c9af ("x86/sev-es: Adjust #VC IST Stack on entering NMI handler")
Reported-by: Alexey Kardashevskiy <aik@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230127035616.508966-1-aik@amd.com
When the coprocessor crashes, it's useful to get a proper register dump
so we can find out what the firmware was doing. Add a decoder for this.
Originally this had ESR decoding by reusing the ARM64 arch header for
this, but that introduces some module linking and cross-arch compilation
issues, so let's leave that out for now.
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Signed-off-by: Asahi Lina <lina@asahilina.net>
Signed-off-by: Hector Martin <marcan@marcan.st>
The commit 848dba781f ("container_of: remove container_of_safe()")
removed the code that uses err.h. Replace the inclusion by stddef.h
which provides offsetof() definition which is still in use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230130111746.59830-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The names of the idle states are misleading being this a single cluster
SoC, a cluster-sleep idle state is impossible!
After some research in ATF, it emerged that the cpu-sleep state is in
reality putting CPUs in retention state, while the cluster-sleep one
is turning off the CPUs.
Summarizing renaming:
- cpu-sleep -> cpu-retention
- cluster-sleep -> cpu-off
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230126103526.417039-7-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The names of the idle states are misleading being this a single cluster
SoC, a cluster-off idle state is impossible!
After some research in ATF, it emerged that the cpu-off state is in
reality putting CPUs in retention state, while the cluster-off one
is turning off the CPUs.
Summarizing renaming:
- cpu-off -> cpu-retention
- cluster-off -> cpu-off
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230126103526.417039-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The names of the idle states are misleading being this a single cluster
SoC, a cluster-off idle state is impossible!
After some research in ATF, it emerged that the cpu-off state is in
reality putting CPUs in retention state, while the cluster-off one
is turning off the CPUs.
Summarizing renaming:
- cpu-off -> cpu-retention
- cluster-off -> cpu-off
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230126103526.417039-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT8186 features the ARM DynamIQ technology and combines both two
Cortex-A76 (big) and six Cortex-A55 (LITTLE) CPUs in one cluster:
fix the CPU map to reflect that.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Fixes: 2e78620b13 ("arm64: dts: Add MediaTek MT8186 dts and evaluation board and Makefile")
Link: https://lore.kernel.org/r/20230126103526.417039-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT8192 features the ARM DynamIQ technology and combines both four
Cortex-A76 (big) and four Cortex-A55 (LITTLE) CPUs in one cluster:
fix the CPU map to reflect that.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Fixes: 48489980e2 ("arm64: dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile")
Link: https://lore.kernel.org/r/20230126103526.417039-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT8195 features the ARM DynamIQ technology and combines both four
Cortex-A78 (big) and four Cortex-A55 (LITTLE) CPUs in one cluster:
fix the CPU map to reflect that.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Fixes: 37f2582883 ("arm64: dts: Add mediatek SoC mt8195 and evaluation board")
Link: https://lore.kernel.org/r/20230126103526.417039-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
While we normally encourage devm usage by drivers, some consumers (and
in particular the upcoming Rust abstractions) might want to manually
manage memory. Export the raw functions to make this possible.
Signed-off-by: Asahi Lina <lina@asahilina.net>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Signed-off-by: Hector Martin <marcan@marcan.st>
This allows downstream consumers to keep track of private data for shmem
mappings. In particular, the Rust abstraction will use this to safely
drop data associated with a mapping when it is unmapped.
Signed-off-by: Asahi Lina <lina@asahilina.net>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Signed-off-by: Hector Martin <marcan@marcan.st>
This requires changing the reset path locking primitives to the spinlock
path in genpd, instead of the mutex path.
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Hector Martin <marcan@marcan.st>
This is yet another low power mode, used by DCP.
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Hector Martin <marcan@marcan.st>
Move PARIDE protocol modules out of drivers/block into
drivers/ata/pata_parport and update the CONFIG_ symbol names to
PATA_PARPORT.
[Damien]
The pata_parport driver file itsef is also moved together with the
protocol modules in drivers/ata/pata_parport.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Enable support for restricted DMA pools which provide a level of DMA
memory protection on systems with limited hardware protection
capabilities, such as those lacking an IOMMU.
For instance, mt8192-asurada-spherion makes use of this to provide a
restricted DMA region for WiFi since its MT7921E WiFi card is connected
through PCIe, and the MT8192 SoC doesn't have an IOMMU context for the
PCIe controller.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20230130200820.82084-2-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable missing configs in the arm64 defconfig to get all devices probing
on mt8192-asurada based machines.
The devices enabled are: MediaTek Bluetooth USB controller, MediaTek
PCIe Gen3 MAC controller, MT7921E wireless adapter, Elan I2C Trackpad,
MediaTek SPI NOR flash controller, Mediatek SPMI Controller, ChromeOS EC
regulators, MT6315 PMIC, MediaTek Video Codec, MT8192 sound cards,
ChromeOS EC rpmsg communication, all MT8192 clocks.
REGULATOR_CROS_EC is enabled as builtin since it powers the MMC
controller for the SD card, making it required for booting on some
setups.
The MT8192 clocks are enabled as builtin for now since their Kconfigs
are bool, and will be changed to modules after those Kconfigs are
reworked.
Restricted DMA pool support is also required to get working WiFi, but
it is enabled in a separate commit since it alters behavior of other
platforms and devices.
By enabling the support for all of this platform's devices on the
defconfig we make it effortless to test the relevant hardware both by
developers as well as CI systems like KernelCI.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20230130200820.82084-1-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmPW7E8eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGf7MIAI0JnHN9WvtEukSZ
E6j6+cEGWxsvD6q0g3GPolaKOCw7hlv0pWcFJFcUAt0jebspMdxV2oUGJ8RYW7Lg
nCcHvEVswGKLAQtQSWw52qotW6fUfMPsNYYB5l31sm1sKH4Cgss0W7l2HxO/1LvG
TSeNHX53vNAZ8pVnFYEWCSXC9bzrmU/VALF2EV00cdICmfvjlgkELGXoLKJJWzUp
s63fBHYGGURSgwIWOKStoO6HNo0j/F/wcSMx8leY8qDUtVKHj4v24EvSgxUSDBER
ch3LiSQ6qf4sw/z7pqruKFthKOrlNmcc0phjiES0xwwGiNhLv0z3rAhc4OM2cgYh
SDc/Y/c=
=zpaD
-----END PGP SIGNATURE-----
Merge v6.2-rc6 into drm-next
Due to holidays we started -next with more -fixes in-flight than
usual, and people have been asking where they are. Backmerge to get
things better in sync.
Conflicts:
- Tiny conflict in drm_fbdev_generic.c between variable rename and
missing error handling that got added.
- Conflict in drm_fb_helper.c between the added call to vgaswitcheroo
in drm_fb_helper_single_fb_probe and a refactor patch that extracted
lots of helpers and incidentally removed the dev local variable.
Readd it to make things compile.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Current snd_soc_dai has data for Playback/Capture, but it is very
random. Someone is array (A), someone is playback/capture (B),
and someone is tx/rx (C);
struct snd_soc_dai {
...
(A) unsigned int stream_active[SNDRV_PCM_STREAM_LAST + 1];
(B) struct snd_soc_dapm_widget *playback_widget;
(B) struct snd_soc_dapm_widget *capture_widget;
(B) void *playback_dma_data;
(B) void *capture_dma_data;
...
(C) unsigned int tx_mask;
(C) unsigned int rx_mask;
};
Because of it, the code was very complicated.
This patch creates new data structure to merge these into one,
and tidyup the code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87cz6vea1v.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87fsbrea25.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87ilgnea2p.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87k013ea2u.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/87r0vbea3r.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/87sffrea3z.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
