There are several places where we can crash the kernel by requesting
lines, unbinding the GPIO device, then calling any of the system calls
relevant to the GPIO character device's annonymous file descriptors:
ioctl(), read(), poll().
While I observed it with the GPIO simulator, it will also happen for any
of the GPIO devices that can be hot-unplugged - for instance any HID GPIO
expander (e.g. CP2112).
This affects both v1 and v2 uAPI.
This fixes it partially by checking if gdev->chip is not NULL but it
doesn't entirely remedy the situation as we still have a race condition
in which another thread can remove the device after the check.
Fixes: d7c51b47ac ("gpio: userspace ABI for reading/writing GPIO lines")
Fixes: 3c0d9c635a ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL")
Fixes: aad955842d ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL")
Fixes: a54756cb24 ("gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL")
Fixes: 7b8e00d981 ("gpiolib: cdev: support GPIO_V2_LINE_SET_VALUES_IOCTL")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
hwm_pcode_read_i1 is called during i915 load. This results in the following
warning from snb_pcode_read because POWER_SETUP_SUBCOMMAND_READ_I1 is
unsupported on DG1/DG2.
[drm:snb_pcode_read [i915]] warning: pcode (read from mbox 47c) \
mailbox access failed for snb_pcode_read_p [i915]: -6
The code handles the unsupported command but the warning in dmesg is
a red herring which has resulted in a couple of bugs being filed.
Therefore silence the warning by avoiding calling snb_pcode_read_p
for DG1/DG2.
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221203031454.1280538-1-ashutosh.dixit@intel.com
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-12-05 (i40e)
Michal clears XPS init flag on reset to allow for updated values to be
written.
Sylwester adds sleep to VF reset to resolve issue of VFs not getting
resources.
Przemyslaw rejects filters for raw IPv4 or IPv6 l4_4_bytes filters as they
are not supported.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: Disallow ip4 and ip6 l4_4_bytes
i40e: Fix for VF MAC address 0
i40e: Fix not setting default xps_cpus after reset
====================
Link: https://lore.kernel.org/r/20221205212523.3197565-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds reset parameter to mtk_wed_rx_ring_setup signature
in order to align rx_ring_setup callback to tx_ring_setup one introduced
in 'commit 23dca7a900 ("net: ethernet: mtk_wed: add reset to
tx_ring_setup callback")'
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/29c6e7a5469e784406cf3e2920351d1207713d05.1670239984.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Semicolons after "}" are not needed.
Signed-off-by: zhang songyi <zhang.songyi@zte.com.cn>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/202212051422158113766@zte.com.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/202212051021451139126@zte.com.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel says:
====================
ipv4: Two small fixes for bugs in IPv4 routing code.
A variation of the second bug was reported by an FRR 5.0 (released
06/18) user as this version was setting a table ID of 0 for the
default VRF, unlike iproute2 and newer FRR versions.
The first bug was discovered while fixing the second.
Both bugs are not regressions (never worked) and are not critical
in my opinion, so the fixes can be applied to net-next, if desired.
No regressions in other tests:
# ./fib_tests.sh
...
Tests passed: 191
Tests failed: 0
====================
Link: https://lore.kernel.org/r/20221204075045.3780097-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cited commit added the table ID to the FIB info structure, but did not
properly initialize it when table ID 0 is used. This can lead to a route
in the default VRF with a preferred source address not being flushed
when the address is deleted.
Consider the following example:
# ip address add dev dummy1 192.0.2.1/28
# ip address add dev dummy1 192.0.2.17/28
# ip route add 198.51.100.0/24 via 192.0.2.2 src 192.0.2.17 metric 100
# ip route add table 0 198.51.100.0/24 via 192.0.2.2 src 192.0.2.17 metric 200
# ip route show 198.51.100.0/24
198.51.100.0/24 via 192.0.2.2 dev dummy1 src 192.0.2.17 metric 100
198.51.100.0/24 via 192.0.2.2 dev dummy1 src 192.0.2.17 metric 200
Both routes are installed in the default VRF, but they are using two
different FIB info structures. One with a metric of 100 and table ID of
254 (main) and one with a metric of 200 and table ID of 0. Therefore,
when the preferred source address is deleted from the default VRF,
the second route is not flushed:
# ip address del dev dummy1 192.0.2.17/28
# ip route show 198.51.100.0/24
198.51.100.0/24 via 192.0.2.2 dev dummy1 src 192.0.2.17 metric 200
Fix by storing a table ID of 254 instead of 0 in the route configuration
structure.
Add a test case that fails before the fix:
# ./fib_tests.sh -t ipv4_del_addr
IPv4 delete address route tests
Regular FIB info
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Identical FIB info with different table ID
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Table ID 0
TEST: Route removed in default VRF when source address deleted [FAIL]
Tests passed: 8
Tests failed: 1
And passes after:
# ./fib_tests.sh -t ipv4_del_addr
IPv4 delete address route tests
Regular FIB info
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Identical FIB info with different table ID
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Table ID 0
TEST: Route removed in default VRF when source address deleted [ OK ]
Tests passed: 9
Tests failed: 0
Fixes: 5a56a0b3a4 ("net: Don't delete routes in different VRFs")
Reported-by: Donald Sharp <sharpd@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cited commit added the table ID to the FIB info structure, but did not
prevent structures with different table IDs from being consolidated.
This can lead to routes being flushed from a VRF when an address is
deleted from a different VRF.
Fix by taking the table ID into account when looking for a matching FIB
info. This is already done for FIB info structures backed by a nexthop
object in fib_find_info_nh().
Add test cases that fail before the fix:
# ./fib_tests.sh -t ipv4_del_addr
IPv4 delete address route tests
Regular FIB info
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Identical FIB info with different table ID
TEST: Route removed from VRF when source address deleted [FAIL]
TEST: Route in default VRF not removed [ OK ]
RTNETLINK answers: File exists
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [FAIL]
Tests passed: 6
Tests failed: 2
And pass after:
# ./fib_tests.sh -t ipv4_del_addr
IPv4 delete address route tests
Regular FIB info
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Identical FIB info with different table ID
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Tests passed: 8
Tests failed: 0
Fixes: 5a56a0b3a4 ("net: Don't delete routes in different VRFs")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
q6v5_wcss_qcs404_power_on() have no fail path for readl_poll_timeout().
Add fail path for readl_poll_timeout().
Fixes: 0af65b9b91 ("remoteproc: qcom: wcss: Add non pas wcss Q6 support for QCS404")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221204082757.18850-1-shangxiaojing@huawei.com
The pointer node is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: b9e718e950 ("remoteproc: Introduce Qualcomm ADSP PIL")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221203070639.15128-1-yuancan@huawei.com
Prior to the Fixes: commit, the initialization code went through the
same fec_enet_set_coalesce() function as used by ethtool, and that
function correctly checks whether the current variant has support for
irq coalescing.
Now that the initialization code instead calls fec_enet_itr_coal_set()
directly, that call needs to be guarded by a check for the
FEC_QUIRK_HAS_COALESCE bit.
Fixes: df727d4547 (net: fec: don't reset irq coalesce settings to defaults on "ip link up")
Reported-by: Greg Ungerer <gregungerer@westnet.com.au>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221205204604.869853-1-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In commit 4d633d1b46 ("bonding: fix ICMPv6 header handling when receiving
IPv6 messages"), there is a copy/paste issue for NA daddr. I found that
in my testing and fixed it in my local branch. But I forgot to re-format
the patch and sent the wrong mail.
Fix it by reading the correct dest address.
Fixes: 4d633d1b46 ("bonding: fix ICMPv6 header handling when receiving IPv6 messages")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Link: https://lore.kernel.org/r/20221206032055.7517-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Leaving wakeup enabled during probe fail (-EPROBE_DEFER) or remove makes
the subsequent probe fail.
[ 3.749454] remoteproc remoteproc0: releasing 3000000.remoteproc
[ 3.752949] qcom_q6v5_pas: probe of 3000000.remoteproc failed with error -17
[ 3.878935] remoteproc remoteproc0: releasing 4080000.remoteproc
[ 3.887602] qcom_q6v5_pas: probe of 4080000.remoteproc failed with error -17
[ 4.319552] remoteproc remoteproc0: releasing 8300000.remoteproc
[ 4.332716] qcom_q6v5_pas: probe of 8300000.remoteproc failed with error -17
Fix this by disabling wakeup in both cases so the driver can properly
probe on the next try.
Fixes: a781e5aa59 ("remoteproc: core: Prevent system suspend during remoteproc recovery")
Fixes: dc86c129b4 ("remoteproc: qcom: pas: Mark devices as wakeup capable")
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221118090816.100012-1-luca.weiss@fairphone.com
q6v5_wcss_init_mmio() will call platform_get_resource_byname() that may
fail and return NULL. devm_ioremap() will use res->start as input, which
may causes null-ptr-deref. Check the ret value of
platform_get_resource_byname() to avoid the null-ptr-deref.
Fixes: 0af65b9b91 ("remoteproc: qcom: wcss: Add non pas wcss Q6 support for QCS404")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221125021641.29392-1-shangxiaojing@huawei.com
The kfree() should be called when of_irq_get_byname() fails or
devm_request_threaded_irq() fails in qcom_add_sysmon_subdev(),
otherwise there will be a memory leak, so add kfree() to fix it.
Fixes: 027045a6e2 ("remoteproc: qcom: Add shutdown-ack irq")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221129105650.1539187-1-cuigaosheng1@huawei.com
Commit ff6d365898 ("soc: qcom: qmi: use const for struct
qmi_elem_info") allows QMI message encoding/decoding rules to be
const, so do that for sysmon.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220914234705.28405-3-quic_jjohnson@quicinc.com
We add ONE_REG interface for VCPU mvendorid, marchid, and mimpid
so that KVM user-space can change this details to support migration
across heterogeneous hosts.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
We should save VCPU mvendorid, marchid, and mimpid at the time
of creating VCPU so that we don't have to do host SBI call every
time Guest/VM ask for these details.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
The sbi_get_mvendorid(), sbi_get_marchid(), and sbi_get_mimpid()
can be used by KVM module so let us export these functions.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Just like asm/kvm_vcpu_timer.h, we should have all sbi related struct
and functions in asm/kvm_vcpu_sbi.h.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
We should use switch-case in kvm_riscv_vcpu_set/get_reg() functions
because the else-if ladder is quite big now.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
We should include asm/csr.h only where required so let us remove
redundant includes of this header.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
The asm/kvm_vcpu_timer.h is redundantly included in vcpu_sbi_base.c
so let us remove it.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
The reg_val check in kvm_riscv_vcpu_set_reg_config() should only
be done for isa config register.
Fixes: 9bfd900bee ("RISC-V: KVM: Improve ISA extension by using a bitmap")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
In kvm_arch_prepare_memory_region(), if no error occurs, a spin_lock()/
spin_unlock() call can be avoided.
Switch to kvm_riscv_gstage_iounmap() that is the same as the current code,
but with a better semantic.
It also embeds the locking logic. So it is avoided if ret == 0.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Anup Patel <anup@brainfault.org>
If xfer_to_guest_mode_handle_work() fails in the run-loop then exit
the run-loop immediately instead of doing it after some more work.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
vma_lookup() finds the vma of a specific address with a cleaner
interface and is more readable.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Several lines of code are inserted to remove KVM module normally
using rmmod command just like others.
Signed-off-by: XiakaiPan <13212017962@163.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Andrii Nakryiko says:
====================
Disentangle prune and jump points in BPF verifier code. They are conceptually
independent but currently coupled together. This small patch set refactors
related code and make it possible to have some instruction marked as pruning
or jump point independently.
Besides just conceptual cleanliness, this allows to remove unnecessary jump
points (saving a tiny bit of performance and memory usage, potentially), and
even more importantly it allows for clean extension of special pruning points,
similarly to how it's done for BPF_FUNC_timer_set_callback. This will be used
by future patches implementing open-coded BPF iterators.
v1->v2:
- clarified path #3 commit message and a comment in the code (John);
- added back mark_jmp_point() to right after subprog call to record
non-linear implicit jump from BPF_EXIT to right after CALL <subprog>.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Don't mark some instructions as jump points when there are actually no
jumps and instructions are just processed sequentially. Such case is
handled naturally by precision backtracking logic without the need to
update jump history. See get_prev_insn_idx(). It goes back linearly by
one instruction, unless current top of jmp_history is pointing to
current instruction. In such case we use `st->jmp_history[cnt - 1].prev_idx`
to find instruction from which we jumped to the current instruction
non-linearly.
Also remove both jump and prune point marking for instruction right
after unconditional jumps, as program flow can get to the instruction
right after unconditional jump instruction only if there is a jump to
that instruction from somewhere else in the program. In such case we'll
mark such instruction as prune/jump point because it's a destination of
a jump.
This change has no changes in terms of number of instructions or states
processes across Cilium and selftests programs.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/20221206233345.438540-4-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Jump history updating and state equivalence checks are conceptually
independent, so move push_jmp_history() out of is_state_visited(). Also
make a decision whether to perform state equivalence checks or not one
layer higher in do_check(), keeping is_state_visited() unconditionally
performing state checks.
push_jmp_history() should be performed after state checks. There is just
one small non-uniformity. When is_state_visited() finds already
validated equivalent state, it propagates precision marks to current
state's parent chain. For this to work correctly, jump history has to be
updated, so is_state_visited() is doing that internally.
But if no equivalent verified state is found, jump history has to be
updated in a newly cloned child state, so is_jmp_point()
+ push_jmp_history() is performed after is_state_visited() exited with
zero result, which means "proceed with validation".
This change has no functional changes. It's not strictly necessary, but
feels right to decouple these two processes.
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20221206233345.438540-3-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
BPF verifier marks some instructions as prune points. Currently these
prune points serve two purposes.
It's a point where verifier tries to find previously verified state and
check current state's equivalence to short circuit verification for
current code path.
But also currently it's a point where jump history, used for precision
backtracking, is updated. This is done so that non-linear flow of
execution could be properly backtracked.
Such coupling is coincidental and unnecessary. Some prune points are not
part of some non-linear jump path, so don't need update of jump history.
On the other hand, not all instructions which have to be recorded in
jump history necessarily are good prune points.
This patch splits prune and jump points into independent flags.
Currently all prune points are marked as jump points to minimize amount
of changes in this patch, but next patch will perform some optimization
of prune vs jmp point placement.
No functional changes are intended.
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20221206233345.438540-2-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
syzkaller reported a memleak:
https://syzkaller.appspot.com/bug?id=62f37ff612f0021641eda5b17f056f1668aa9aed
unreferenced object 0xffff88811009c7f8 (size 136):
...
backtrace:
[<ffffffff821db19b>] z_erofs_do_read_page+0x99b/0x1740
[<ffffffff821dee9e>] z_erofs_readahead+0x24e/0x580
[<ffffffff814bc0d6>] read_pages+0x86/0x3d0
...
syzkaller constructed a case: in z_erofs_register_pcluster(),
ztailpacking = false and map->m_pa = zero. This makes pcl->obj.index be
zero although pcl is not a inline pcluster.
Then following path adds refcount for grp, but the refcount won't be put
because pcl is inline.
z_erofs_readahead()
z_erofs_do_read_page() # for another page
z_erofs_collector_begin()
erofs_find_workgroup()
erofs_workgroup_get()
Since it's illegal for the block address of a non-inlined pcluster to
be zero, add check here to avoid registering the pcluster which would
be leaked.
Fixes: cecf864d3d ("erofs: support inline data decompression")
Reported-by: syzbot+6f8cd9a0155b366d227f@syzkaller.appspotmail.com
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Reviewed-by: Yue Hu <huyue2@coolpad.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/Y42Kz6sVkf+XqJRB@debian
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Enable large folios for fscache mode. Enable this feature for
non-compressed format for now, until the compression part supports large
folios later.
One thing worth noting is that, the feature is not enabled for the meta
data routine since meta inodes don't need large folios for now, nor do
they support readahead yet.
Also document this new feature.
Signed-off-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Jia Zhu <zhujia.zj@bytedance.com>
Link: https://lore.kernel.org/r/20221201074256.16639-3-jefflexu@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
When large folios supported, one folio can be split into several slices,
each of which may be mapped to META/UNMAPPED/MAPPED, and the folio can
be unlocked as a whole only when all slices have completed.
Thus always allocate erofs_fscache_request for each .read_folio() or
.readahead(), in which case the allocated request is responsible for
unlocking folios when all slices have completed.
As described above, each folio or folio range can be mapped into several
slices, while these slices may be mapped to different cookies, and thus
each slice needs its own netfs_cache_resources. Here we introduce
chained requests to support this, where each .read_folio() or
.readahead() calling can correspond to multiple requests. Each request
has its own netfs_cache_resources and thus is used to access one cookie.
Among these requests, there's a primary request, with the others
pointing to the primary request.
Signed-off-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Jia Zhu <zhujia.zj@bytedance.com>
Link: https://lore.kernel.org/r/20221201074256.16639-2-jefflexu@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Switch to prepare_ondemand_read() interface and a self-contained request
completion to get rid of netfs_io_[request|subrequest].
The whole request will still be split into slices (subrequest) according
to the cache state of the backing file. As long as one of the
subrequests fails, the whole request will be marked as failed.
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Jia Zhu <zhujia.zj@bytedance.com>
Link: https://lore.kernel.org/r/20221124034212.81892-3-jefflexu@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Add prepare_ondemand_read() callback dedicated for the on-demand read
scenario, so that callers from this scenario can be decoupled from
netfs_io_subrequest.
The original cachefiles_prepare_read() is now refactored to a generic
routine accepting a parameter list instead of netfs_io_subrequest.
There's no logic change, except that the debug id of subrequest and
request is removed from trace_cachefiles_prep_read().
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Acked-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/20221124034212.81892-2-jefflexu@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
After commit 4c7e42552b ("erofs: remove useless cache strategy of
DELAYEDALLOC"), only one cached I/O allocation strategy is supported:
When cached I/O is preferred, page allocation is applied without
direct reclaim. If allocation fails, fall back to inplace I/O.
Let's get rid of z_erofs_cache_alloctype. No logical changes.
Reviewed-by: Yue Hu <huyue2@coolpad.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Yue Hu <huyue2@coolpad.com>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221206060352.152830-1-xiang@kernel.org
We currently have some complicated code in sfp_probe() which gets the
I2C bus depending on whether the sfp node is DT or ACPI, and we use
completely separate lookup functions.
This could do with being in a separate function to make the code more
readable, so move it to a new function, sfp_i2c_get(). We can also use
fwnode_find_reference() to lookup the I2C bus fwnode before then
decending into fwnode-type specific parsing.
A future cleanup would be to move the fwnode-type specific parsing into
the i2c layer, which is where it really should be.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1p1WGJ-0098wS-4w@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When shared domain is enabled, doing mount twice with the same fsid and
domain_id will trigger sysfs warning as shown below:
sysfs: cannot create duplicate filename '/fs/erofs/d0,meta.bin'
CPU: 15 PID: 1051 Comm: mount Not tainted 6.1.0-rc6+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
Call Trace:
<TASK>
dump_stack_lvl+0x38/0x49
dump_stack+0x10/0x12
sysfs_warn_dup.cold+0x17/0x27
sysfs_create_dir_ns+0xb8/0xd0
kobject_add_internal+0xb1/0x240
kobject_init_and_add+0x71/0xa0
erofs_register_sysfs+0x89/0x110
erofs_fc_fill_super+0x98c/0xaf0
vfs_get_super+0x7d/0x100
get_tree_nodev+0x16/0x20
erofs_fc_get_tree+0x20/0x30
vfs_get_tree+0x24/0xb0
path_mount+0x2fa/0xa90
do_mount+0x7c/0xa0
__x64_sys_mount+0x8b/0xe0
do_syscall_64+0x30/0x60
entry_SYSCALL_64_after_hwframe+0x46/0xb0
The reason is erofs_fscache_register_cookie() doesn't guarantee the primary
data blob (aka fsid) is unique in the shared domain and
erofs_register_sysfs() invoked by the second mount will fail due to the
duplicated fsid in the shared domain and report warning.
It would be better to check the uniqueness of fsid before doing
erofs_register_sysfs(), so adding a new flags parameter for
erofs_fscache_register_cookie() and doing the uniqueness check if
EROFS_REG_COOKIE_NEED_NOEXIST is enabled.
After the patch, the error in dmesg for the duplicated mount would be:
erofs: ...: erofs_domain_register_cookie: XX already exists in domain YY
Reviewed-by: Jia Zhu <zhujia.zj@bytedance.com>
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20221125110822.3812942-1-houtao@huaweicloud.com
Fixes: 7d41963759 ("erofs: Support sharing cookies in the same domain")
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Enable large folios for iomap mode. Then the readahead routine will
pass down large folios containing multiple pages.
Let's enable this for non-compressed format for now, until the
compression part supports large folios later.
When large folios supported, the iomap routine will allocate iomap_page
for each large folio and thus we need iomap_release_folio() and
iomap_invalidate_folio() to free iomap_page when these folios get
reclaimed or invalidated.
Signed-off-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20221130060455.44532-1-jefflexu@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
btf->struct_meta_tab is populated by btf_parse_struct_metas in btf.c.
There, a BTF record is created for any type containing a spin_lock or
any next-gen datastructure node/head.
Currently, for non-MAP_VALUE types, reg_btf_record will only search for
a record using struct_meta_tab if the reg->type exactly matches
(PTR_TO_BTF_ID | MEM_ALLOC). This exact match is too strict: an
"allocated obj" type - returned from bpf_obj_new - might pick up other
flags while working its way through the program.
Loosen the check to be exact for base_type and just use MEM_ALLOC mask
for type_flag.
This patch is marked Fixes as the original intent of reg_btf_record was
unlikely to have been to fail finding btf_record for valid alloc obj
types with additional flags, some of which (e.g. PTR_UNTRUSTED)
are valid register type states for alloc obj independent of this series.
However, I didn't find a specific broken repro case outside of this
series' added functionality, so it's possible that nothing was
triggering this logic error before.
Signed-off-by: Dave Marchevsky <davemarchevsky@fb.com>
cc: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Fixes: 4e814da0d5 ("bpf: Allow locking bpf_spin_lock in allocated objects")
Link: https://lore.kernel.org/r/20221206231000.3180914-2-davemarchevsky@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
