Relocate the wake-gpios and perst-gpios properties from the pcie0
controller node to the pcieport0 node. These GPIOs are associated with
the PCIe root port and should reside under the pcieport0 node.
Also rename perst-gpios to reset-gpios to match the expected property name
in the PCIe port node.
Fixes: 141714e163 ("arm64: dts: qcom: sm8750-mtp: Add WiFi and Bluetooth")
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20251008-sm8750-v1-1-daeadfcae980@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The UFS device is ovbiously dma coherent like the other IOMMU devices
like usb, mmc, ... let's fix this by adding the flag.
To be sure an extensive test has been performed to be sure it's
safe, as downstream uses this flag for UFS as well.
As an experiment, I checked how the dma-coherent could impact
the UFS bandwidth, and it happens the max bandwidth on cached
write is slighly highter (up to 10%) while using less cpu time
since cache sync/flush is skipped.
Fixes: 10e0246712 ("arm64: dts: qcom: sm8650: add interconnect dependent device nodes")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251007-topic-sm8650-upstream-ufs-dma-coherent-v1-1-f3cfeaee04ce@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the correct compatible for this phone with standard Qualcomm
firmware and remove references to power-domains from a 'reserved' node.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250930-sc7280-dts-misc-v1-5-5a45923ef705@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the correct compatible for this phone with standard Qualcomm
firmware and remove references to power-domains from a 'reserved' node.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250930-sc7280-dts-misc-v1-4-5a45923ef705@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the correct compatible for this phone with standard Qualcomm
firmware and remove references to power-domains from a 'reserved' node.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250930-sc7280-dts-misc-v1-3-5a45923ef705@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the OLED power supplies to the simple-framebuffer node, so that
the regulators don't get turned off while the simple-fb is being used.
Fixes: c365a02615 ("arm64: dts: qcom: qcm6490-fairphone-fp5: Enable display")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250930-sc7280-dts-misc-v1-1-5a45923ef705@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Like on other platforms, if the OS does not support recovering the state
left by the bootloader it needs access to MDSS_CORE, so that it can
clear the MDSS configuration. Add a reference to the relevant reset.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> # RB5
Link: https://lore.kernel.org/r/20250930-sm8250-mdss-reset-v1-1-a64522d91f12@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Radxa Dragon Q6A is a single board computer, based on the Qualcomm
QCS6490 platform.
Features enabled and working:
- Configurable I2C/SPI/UART from 40-Pin GPIO
- Three USB-A 2.0 ports
- RTL8111K Ethernet connected to PCIe0
- eMMC module
- SD card
- M.2 M-Key 2230 PCIe 3.0 x2
- Headphone jack
- Onboard thermal sensors
- QSPI controller for updating boot firmware
- ADSP remoteproc (Type-C and charging features disabled in firmware)
- CDSP remoteproc (for AI applications using QNN)
- Venus video encode and decode accelerator
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xilin Wu <sophon@radxa.com>
Link: https://lore.kernel.org/r/20250929-radxa-dragon-q6a-v5-2-aa96ffc352f8@radxa.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Radxa Dragon Q6A is a single board computer, based on the Qualcomm
QCS6490 platform.
Document the top-level compatible for this board.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Xilin Wu <sophon@radxa.com>
Link: https://lore.kernel.org/r/20250929-radxa-dragon-q6a-v5-1-aa96ffc352f8@radxa.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Instead of creating ad-hoc new register definitions with altered
register addresses to mimic the VF's access to these registers,
prepare new MMIO instance per required VF, with shifted internal
location of the register map. This will allow to use unmodified
register definitions in all calls to xe_mmio() functions.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patch.msgid.link/20251024205826.4652-1-michal.wajdeczko@intel.com
Unlike UX3407QA with WCN6855, UX3407RA comes with WCN7850. Definitions
were not added during initial bringup due to lack of hardware to test
it. Add missing definitions that were now confirmed to work.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Aleksandrs Vinarskis <alex@vinarskis.com>
Link: https://lore.kernel.org/r/20250927-zenbook-improvements-v3-3-d46c7368dc70@vinarskis.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The laptop comes in two variants:
* UX3407RA, higher end, FHD+ OLED or WOXGA+ OLED panels
* UX3407QA, lower end, FHD+ OLED or FHD+ LCD panels
Even though all three panels work with "edp-panel", unfortunately the
brightness adjustmenet of LCD panel is PWM based, requiring a dedicated
device-tree. Convert "x1p42100-asus-zenbook-a14.dts" into ".dtsi" to
allow for this split, introduce new LCD variant. Leave current variant
without postfix and with the unchanged model name, as some distros
(eg. Ubuntu) rely on this for automatic device-tree detection during
kernel installation/upgrade.
As dedicated device-tree is required, update compatibles of OLED
variants to correct ones. Keep "edp-panel" as fallback, since it is
enough to make the panels work.
While at it moving .dts, .dtsi around, drop 'model' from the top level
x1-asus-zenbook-a14.dtsi as well.
Co-developed-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Aleksandrs Vinarskis <alex@vinarskis.com>
Link: https://lore.kernel.org/r/20250927-zenbook-improvements-v3-2-d46c7368dc70@vinarskis.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
X1/X1 Plus variant of the said device comes in either FHD+ OLED or FHD+
LCD panel, and shares the same model number UX3407QA. It appears LCD
panel's brightness adjustment is PWM backlight controlled, so a
dedicated device-tree is required. Introduce dedicated compatibles with
fallback to 'asus,zenbook-a14-ux3407qa' as they are otherwise the same.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Aleksandrs Vinarskis <alex@vinarskis.com>
Link: https://lore.kernel.org/r/20250927-zenbook-improvements-v3-1-d46c7368dc70@vinarskis.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The previous GPIO numbers were wrong. Update them to the correct
ones and fix the label.
Fixes: 288ef8a426 ("arm64: dts: sdm845: add oneplus6/6t devices")
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250927-slider-correct-v1-1-fb8cc7fdcedf@ixit.cz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Since max77705 has a register, which indicates interrupt source, it acts
as an interrupt controller.
Direct MAX77705's subdevices to use the IC's internal interrupt
controller, instead of listening to every interrupt fired by the
chip towards the host device.
Fixes: 7a88a931d0 ("arm64: dts: qcom: sdm845-starqltechn: add max77705 PMIC")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250926-starqltechn-correct_max77705_nodes-v5-2-c6ab35165534@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Drop the unused address/size-cells properties to silence the DT
checker warning:
pmic@66 (maxim,max77705): '#address-cells', '#size-cells' do not
match any of the regexes: '^pinctrl-[0-9]+$'
Fixes: 7a88a931d0 ("arm64: dts: qcom: sdm845-starqltechn: add max77705 PMIC")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250926-starqltechn-correct_max77705_nodes-v5-1-c6ab35165534@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Having removed the use of the cpu_armpmu per-CPU variable from the
interrupt handling, the only user left is the BRBE scheduler hook.
It is easy to drop the use of this variable by following the pointer to the
generic PMU structure, and get the arm_pmu structure from there.
Perform the conversion and kill cpu_armpmu altogether.
Suggested-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Link: https://patch.msgid.link/20251020122944.3074811-27-maz@kernel.org
There is no in-tree users of this helper since b13b41cc3d ("misc:
ti_fpc202: Switch to of_fwnode_handle()"), and is replaced with
of_fwnode_handle().
Get rid of it.
Suggested-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Link: https://patch.msgid.link/20251020122944.3074811-26-maz@kernel.org
These two helpers do not have any user anymore, and can be removed,
together with the affinity field kept in the irqdesc structure.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Link: https://patch.msgid.link/20251020122944.3074811-25-maz@kernel.org
This code is now completely unused, and nobody will ever miss it.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Link: https://patch.msgid.link/20251020122944.3074811-24-maz@kernel.org
Similarly to what has been done for GICv3, drop the irq partitioning
support from the AIC driver, effectively merging the two per-cpu interrupts
for the PMU.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Reviewed-by: Sven Peter <sven@kernel.org>
Link: https://patch.msgid.link/20251020122944.3074811-23-maz@kernel.org
The only thing getting in the way of correctly handling PPIs the way they
were intended is the GICv3 hack that deals with PPI partitions.
Remove that code, allowing the common code to kick in.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Link: https://patch.msgid.link/20251020122944.3074811-22-maz@kernel.org
Let the TRBE driver request interrupts with an affinity mask matching the
TRBE implementation affinity.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://patch.msgid.link/20251020122944.3074811-21-maz@kernel.org
Let the SPE driver request interrupts with an affinity mask matching the SPE
implementation affinity.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Link: https://patch.msgid.link/20251020122944.3074811-20-maz@kernel.org
Let the PMU driver request both NMIs and normal interrupts with an affinity mask
matching the PMU affinity.
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Link: https://patch.msgid.link/20251020122944.3074811-19-maz@kernel.org
While it would be nice to simply make request_percpu_irq() take an affinity
mask, the churn is likely to be on the irritating side given that most
drivers do not give a damn about affinities.
So take the more innocuous path to provide a helper that parallels
request_percpu_irq(), with an affinity as a bonus argument.
Yes, request_percpu_irq_affinity() is a bit of a mouthful.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Link: https://patch.msgid.link/20251020122944.3074811-18-maz@kernel.org
Interrupt sharing for percpu-devid interrupts is forbidden, and for good
reasons. These are interrupts generated *from* a CPU and handled by itself
(timer, for example). Nobody in their right mind would put two devices on
the same pin (and if they have, they get to keep the pieces...).
But this also prevents more benign cases, where devices are connected
to groups of CPUs, and for which the affinities are not overlapping.
Effectively, the only thing they share is the interrupt number, and
nothing else.
Tweak the definition of IRQF_SHARED applied to percpu_devid interrupts to
allow this particular use case. This results in extra validation at the
point of the interrupt being setup and freed, as well as a tiny bit of
extra complexity for interrupts at handling time (to pick the correct
irqaction).
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Link: https://patch.msgid.link/20251020122944.3074811-17-maz@kernel.org
Continue spreading the notion of affinity to the per CPU interrupt request
code by updating the call sites that use request_percpu_nmi() (all two of
them) to take an affinity pointer. This pointer is firmly NULL for now.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Link: https://patch.msgid.link/20251020122944.3074811-16-maz@kernel.org
Add an affinity field to both the irqaction structure and the interrupt
request primitives. Nothing is making use of it yet, and the only value
used it NULL, which is used as a shorthand for cpu_possible_mask.
This will shortly get used with actual affinities.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Link: https://patch.msgid.link/20251020122944.3074811-15-maz@kernel.org
Move the code creating a per-cpu irqaction into its own helper, so that
future changes to this code can be kept localised.
At the same time, fix the documentation which appears to say the wrong
thing when it comes to interrupts being automatically enabled
(percpu_devid interrupts never are).
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/20251020122944.3074811-14-maz@kernel.org
When irqaction::percpu_dev_id was introduced, it was hoped that it could be
part of an anonymous union with dev_id, as the two fields are mutually
exclusive.
However, toolchains used at the time were often showing terrible support
for anonymous unions, breaking the build on a number of architectures. It
was therefore decided to keep the two fields separate and address this down
the line.
14 years later, the compiler dark age is over, and there is universal
support for anonymous unions. Get a whole pointer back that can immediately
be spent on something else.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Link: https://patch.msgid.link/20251020122944.3074811-13-maz@kernel.org
There is no in-tree user of this flow handler anymore, so simply remove it.
Suggested-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Link: https://patch.msgid.link/20251020122944.3074811-12-maz@kernel.org
It so appears that handle_percpu_devid_irq() is extremely similar to
handle_percpu_devid_fasteoi_nmi(), and that the differences do no justify
the horrid machinery in the GICv3 driver to handle the flow handler switch.
Stick with the standard flow handler, even for NMIs.
Suggested-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Link: https://patch.msgid.link/20251020122944.3074811-11-maz@kernel.org
Now that the relevant interrupt controllers are equipped with a callback
returning the affinity of per-CPU interrupts, switch the ARM SPE driver
over to this new method.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Reviewed-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20251020122944.3074811-10-maz@kernel.org
Now that the relevant interrupt controllers are equipped with a callback
returning the affinity of per-CPU interrupts, switch the OF side of the ARM
PMU driver over to this new method.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Reviewed-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20251020122944.3074811-9-maz@kernel.org
Now that the relevant interrupt controllers are equipped with a callback
returning the affinity of per-CPU interrupts, switch the TRBE driver over
to this new method.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://patch.msgid.link/20251020122944.3074811-8-maz@kernel.org
Plug the new .get_fwspec_info() callback into the Apple AIC driver, using
some of the existing FIQ affinity handling infrastructure.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Acked-by: Sven Peter <sven@kernel.org>
Link: https://patch.msgid.link/20251020122944.3074811-7-maz@kernel.org
Plug the new .get_fwspec_info() callback into the GICv3 core driver, using
some of the existing PPI affinity handling infrastructure.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Link: https://patch.msgid.link/20251020122944.3074811-6-maz@kernel.org
Expand platform_get_irq_optional() to also return an affinity if available,
renaming it to platform_get_irq_affinity() in the process.
platform_get_irq_optional() is preserved with its current semantics by
calling into the new helper with a NULL affinity pointer.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/20251020122944.3074811-5-maz@kernel.org
Plug the irq_populate_fwspec_info() helper into the OF layer to offer an
interrupt affinity reporting function.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/20251020122944.3074811-4-maz@kernel.org
Plug the irq_populate_fwspec_info() helper into the ACPI layer to offer an
interrupt affinity reporting function. This is currently only supported for
the CONFIG_ACPI_GENERIC_GSI configurations, but could later be extended to
legacy architectures if necessary.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Acked-by: Rafael J. Wysocki (Intel) <rafael@kernel.org>
Link: https://patch.msgid.link/20251020122944.3074811-3-maz@kernel.org
Add an irqdomain callback to report firmware-provided information that is
otherwise not available in a generic way. This is reported using a new data
structure (struct irq_fwspec_info).
This callback is optional and the only information that can be reported
currently is the affinity of an interrupt. However, the containing
structure is designed to be extensible, allowing other potentially relevant
information to be reported in the future.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Will Deacon <will@kernel.org>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/20251020122944.3074811-2-maz@kernel.org
Limit Entrysign sha256 signature checking to CPUs in the range Zen1-Zen5.
X86_BUG cannot be used here because the loading on the BSP happens way
too early, before the cpufeatures machinery has been set up.
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://patch.msgid.link/all/20251023124629.5385-1-bp@kernel.org
Traditionally, firmware loading for Serial Engines (SE) in the QUP hardware
of Qualcomm SoCs has been managed by TrustZone (TZ). While this approach
ensures secure SE assignment and access control, it limits flexibility for
developers who need to enable various protocols on different SEs.
Add the firmware-name property to QUPv3 nodes in the device tree to enable
firmware loading from the Linux environment. Handle SE assignments and
access control permissions directly within Linux, removing the dependency
on TrustZone.
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250925042605.1388951-1-viken.dadhaniya@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Traditionally, firmware loading for Serial Engines (SE) in the QUP hardware
of Qualcomm SoCs has been managed by TrustZone (TZ). While this approach
ensures secure SE assignment and access control, it limits flexibility for
developers who need to enable various protocols on different SEs.
Add the firmware-name property to QUPv3 nodes in the device tree to enable
firmware loading from the Linux environment. Handle SE assignments and
access control permissions directly within Linux, removing the dependency
on TrustZone.
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Acked-by: Mukesh Kumar Savaliya <mukesh.savaliya@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250924035409.3976652-1-viken.dadhaniya@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Traditionally, firmware loading for Serial Engines (SE) in the QUP hardware
of Qualcomm SoCs has been managed by TrustZone (TZ). While this approach
ensures secure SE assignment and access control, it limits flexibility for
developers who need to enable various protocols on different SEs.
Add the firmware-name property to QUPv3 nodes in the device tree to enable
firmware loading from the Linux environment. Handle SE assignments and
access control permissions directly within Linux, removing the dependency
on TrustZone.
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250923161107.3541698-1-viken.dadhaniya@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The BQ Aquaris X5 (Longcheer L8910) has a Himax HX852x-ES touchscreen,
which can now be described with the bindings recently added to linux-next.
Add it to the device tree to allow using the touchscreen.
Signed-off-by: Jonathan Albrieux <jonathan.albrieux@gmail.com>
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250919-msm8916-l8910-touchscreen-v1-1-c46e56ec0a3b@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Update min/max voltage settings for regulators below to align
with the HW specification
vreg_l3b_0p504
vreg_l6b_1p2
vreg_l11b_1p504
vreg_l14b_1p08
vreg_l16b_1p1
vreg_l17b_1p7
vreg_s1c_2p19
vreg_l8c_1p62
vreg_l9c_2p96
vreg_l12c_1p65.
While at it, remove RPMH regulator rails (listed below) as
these are not to be used on APPS, and any client accidently
voting on it can potentially cause issues.
vreg_s2b_0p876
vreg_s2c_0p752
vreg_s5c_0p752
vreg_s7c_0p752
vreg_s10c_0p752
vreg_l4b_0p752
vreg_l5b_0p752.
Signed-off-by: Rakesh Kota <rakesh.kota@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250919-b4-rb3gen2-update-regulator-v1-1-1ea9e70d01cb@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>