Redirect wm_adsp_release_firmware_files() to a replacement function that
handles the dummy firmware created by the tests. Use the same cleanup
function to cleanup in the test exit() function. Also call it on each
loop in wm_adsp_fw_find_test_find_firmware_byindex() to free the created
strings before reusing priv->found_fw on the next loop.
wm_adsp_release_firmware_files() will pass the struct firmware* pointers
to release_firmware(). But the pointers created by the tests are dummies
and must not be passed to release_firmware().
The test never invokes wm_adsp_release_firmware_files() so it wasn't
redirected. But the error handling in wm_adsp_request_firmware_files()
calls wm_adsp_release_firmware_files(). The redirected function makes
this safe.
Using the same cleanup function to perform cleanup from the test exit()
handler and wm_adsp_fw_find_test_find_firmware_byindex() avoids the risk
of duplicate cleanup code that all needs updating if there is any change
to the cleanup requirements.
This problem was found by https://sashiko.dev.
Fixes: bf2d44d07d ("ASoC: wm_adsp: Add kunit test for firmware file search")
Closes: https://sashiko.dev/#/patchset/20260326100853.1582886-1-rf%40opensource.cirrus.com
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260505105123.3539778-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
By convention MODULE_DEVICE_TABLE() immediately follows the ID table it
exports, because this is easier to read and verify. It also makes more
sense since #ifdef for ACPI or OF could hide both of them.
Most of the privers already have this correctly placed, so adjust
the missing ones. No functional impact.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260505102803.183455-4-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
By convention MODULE_DEVICE_TABLE() immediately follows the ID table it
exports, because this is easier to read and verify. It also makes more
sense since #ifdef for ACPI or OF could hide both of them.
Most of the privers already have this correctly placed, so adjust
the missing ones. No functional impact.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260505102803.183455-3-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
By convention MODULE_DEVICE_TABLE() immediately follows the ID table it
exports, because this is easier to read and verify. It also makes more
sense since #ifdef for ACPI or OF could hide both of them.
Most of the privers already have this correctly placed, so adjust
the missing ones. No functional impact.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260505102734.180464-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The initialisation of jack_state was accidentally moved until after its
use, correct this.
Fixes: cb3c257e08 ("ASoC: SDCA: Add correct masks whilst reporting SDCA jack status")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260505090811.3697153-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce the "k3-j722s-mcu.dtsi" file to contain wakeup domain peripherals
that are specific to J722S SoC and are not shared with AM62P.
Previously, those nodes were squatting the k3-j722s-main.dtsi file which
should contain only main domain peripherals.
Signed-off-by: Richard Genoud (TI) <richard.genoud@bootlin.com>
Link: https://patch.msgid.link/20260427142901.341861-4-richard.genoud@bootlin.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Introduce the "k3-j722s-mcu.dtsi" file to contain mcu domain peripherals
that are specific to J722S SoC and are not shared with AM62P.
Previously, those nodes were squatting the k3-j722s-main.dtsi file which
should contain only main domain peripherals.
Signed-off-by: Richard Genoud (TI) <richard.genoud@bootlin.com>
Link: https://patch.msgid.link/20260427142901.341861-3-richard.genoud@bootlin.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The pinctrl contexts for j722s should be saved and restored during
suspend-to-ram, just like it is done for j7200 and j784s4 SoCs.
Use ti,j7200-padconf compatible to save and restore pinctrl contexts during
suspend-to-ram.
Signed-off-by: Abhash Kumar Jha <a-kumar2@ti.com>
Signed-off-by: Richard Genoud (TI) <richard.genoud@bootlin.com>
Link: https://patch.msgid.link/20260427142901.341861-2-richard.genoud@bootlin.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Firmware connection manager supports only one DMA tunnel per XDomain
connection. Firmware prior Intel Titan Ridge failed the operation
directly but the same does not happen anymore on Titan Ridge and
forward. For this reason add an explicit check, and fail the operation
accordingly in the driver.
Signed-off-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently we call device_unregister() for services and the XDomain
itself with tb->lock held. This prevents the service drivers from
calling any functions that may take it. For this reason separate
removing the XDomain from the topology data structures (where we need
the lock) from unregistering the device from the bus (where remove
callbacks of the drivers are being called).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We add them as part of the register path so to keep it symmetric remove
them as part of the unregister path. This also removes them even if the
service itself is not yet released (but is unregistered), thus allowing
new register with the same service name to happen.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We don't actually need to store the debugfs directory pointer inside
struct dma_test. Instead we can use the debugfs_lookup_and_remove()
which also handles the case if the debugfs directory is already removed
by the core driver (for example when cable is disconnected).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This is needed because we release the service ID in tb_service_release()
and the ID array is owned by the parent XDomain.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We should not call nhi_shutdown() before the domain structure and the
control channel rings are completely released. Otherwise we might
release resources like the nhi->msix_ida that are still referenced in
tb_domain_release(). For this reason wait for the tb_domain_release() to
be completed before continuing to nhi_shutdown() and eventually
releasing of the rest of the data structures.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Similarly what we do with the firmware connection manager. This makes
tb_xdp_handle_request() return error to the remote host. However, we
need to make sure we keep the uuid alive so that we can reply until the
whole domain is released.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If tb_cfg_request() fails setting up the request (for example the
control channel is shut down already) it returns an error without
calling the callback. To avoid leaking that memory, call
tb_cfg_request_put() if tb_cfg_request() fails.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We process hotplug events in a workqueue that may run after the domain
has been removed by tb_domain_remove(). For example if user unloads the
driver while at the same time plugging a device router we may have
scheduled tb_handle_hotplug() to run. Avoid possible UAF in this case by
taking the domain reference before scheduling the hotplug handler in
tb_queue_hotplug().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The USB4 v2 Inter-Domain spec "unified" the lane bonding flow so that
when the other end (with higher UUID) is not yet set the target link
width accordingly it is expected to reply with ERROR_NOT_READY.
Implement this for Linux.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This happens when firmware connection manager is being used. It will
deal with disabling the lane 1 adapter after the tunnel has been
established and re-enabling it afterwards. For this reason only do this
when we know that lane bonding is possible (e.g running software
connection manager).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
According to USB4 spec, USB4 Connection Manager shall not change value
of any fields that are defined as "RsvdZ" or "VD". Specifically fields:
Path Credits Allocated, IFC, ISE fields in path config space shall not
be written by CM. To handle this, CM shall first read current path
config space from the hardware, change only the fields that can be
changed, and then write back the path config space.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently there is no way to install an LTF key seed that can be
used in non-trigger-based (NTB) and trigger-based (TB) FTM ranging
to protect NDP frames. Without this, drivers cannot enable PHY-layer
security for peer measurement sessions, leaving ranging measurements
vulnerable to eavesdropping and manipulation.
Introduce NL80211_KEY_LTF_SEED attribute and the dedicated extended
feature flag NL80211_EXT_FEATURE_SET_KEY_LTF_SEED to allow drivers
to advertise and install LTF key seeds via nl80211. The key seed
must be configured beforehand to ensure the peer measurement session
is secure. The driver must advertise both NL80211_EXT_FEATURE_SECURE_LTF
and NL80211_EXT_FEATURE_SET_KEY_LTF_SEED for the key seed installation
to be permitted.
The LTF key seed is pairwise key material and must only be used with
pairwise key type. Reject attempts to use it with other key types.
Signed-off-by: Peddolla Harshavardhan Reddy <peddolla.reddy@oss.qualcomm.com>
Link: https://patch.msgid.link/20260420090856.2152905-13-peddolla.reddy@oss.qualcomm.com
[fix policy coding style]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Proximity detection often does not require detailed ranging
measurements, yet userspace currently receives full FTM results for
every request, causing unnecessary data transfer, host wakeups, and
processing overhead.
Add an optional control to suppress ranging result reporting for
peer-to-peer PD requests. Introduce the
NL80211_PMSR_FTM_REQ_ATTR_PD_SUPPRESS_RESULTS flag; when set with a
PD request, the device may perform the measurements (e.g. when acting
as RSTA) but must not report the measurement results to userspace.
Validate that the flag is only accepted when request_type is set to
NL80211_PMSR_FTM_REQ_TYPE_PD, reject otherwise.
Signed-off-by: Peddolla Harshavardhan Reddy <peddolla.reddy@oss.qualcomm.com>
Link: https://patch.msgid.link/20260420090856.2152905-12-peddolla.reddy@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Devices may support different preamble and bandwidth configurations
for proximity detection (PD) ranging versus standard ranging. Add
separate pd_preambles and pd_bandwidths fields to
cfg80211_pmsr_capabilities to allow drivers to advertise PD-specific
capabilities.
Expose these over nl80211 using new attributes
NL80211_PMSR_FTM_CAPA_ATTR_PD_PREAMBLES and
NL80211_PMSR_FTM_CAPA_ATTR_PD_BANDWIDTHS, advertised only when
pd_support is set.
For PD requests, validate bandwidth and preamble against pd_bandwidths
and pd_preambles. For non-PD requests, validate against the existing
bandwidths and preambles fields.
Signed-off-by: Peddolla Harshavardhan Reddy <peddolla.reddy@oss.qualcomm.com>
Link: https://patch.msgid.link/20260420090856.2152905-11-peddolla.reddy@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Proximity detection applications need to receive measurement results
only when devices cross specific distance boundaries to avoid
unnecessary host wakeups and reduce power consumption.
Introduce configurable distance-based reporting thresholds that
drivers can use to implement selective result reporting. Add ingress
and egress distance parameters allowing applications to specify when
results should be reported as peers cross these boundaries.
Signed-off-by: Peddolla Harshavardhan Reddy <peddolla.reddy@oss.qualcomm.com>
Link: https://patch.msgid.link/20260420090856.2152905-10-peddolla.reddy@oss.qualcomm.com
[remove mm units from variables]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Peer measurement capabilities currently advertise a single maximum
peer count regardless of device role. Some devices support different
peer limits when operating as initiator versus responder.
Add max_peers fields inside the ftm.ista and ftm.rsta sub-structs of
cfg80211_pmsr_capabilities to allow drivers to advertise per-role peer
limits. These limits are generic and not restricted to any specific
ranging type.
Expose these over nl80211 using new NL80211_PMSR_ATTR_MAX_PEER_ISTA_ROLE
and NL80211_PMSR_ATTR_MAX_PEER_RSTA_ROLE attributes inside the
ISTA_CAPS and RSTA_CAPS nested attributes respectively.
When a role limit is advertised, validate the number of peers in the
request separately for each role using the existing rsta flag in the
FTM request, and reject the request if the limit is exceeded.
Signed-off-by: Peddolla Harshavardhan Reddy <peddolla.reddy@oss.qualcomm.com>
Link: https://patch.msgid.link/20260420090856.2152905-9-peddolla.reddy@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Applications need negotiated session parameters to interpret
proximity ranging results and perform post-processing. Currently,
the FTM response lacks LTF repetition counts, time constraints,
spatial stream configuration, and availability window parameters.
Extend the FTM response structure to report these negotiated
parameters, enabling applications to track session configuration
and use them in post-processing to increase ranging precision.
Signed-off-by: Peddolla Harshavardhan Reddy <peddolla.reddy@oss.qualcomm.com>
Link: https://patch.msgid.link/20260420090856.2152905-8-peddolla.reddy@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enable NTB continuous ranging with configurable timing and measurement
parameters as per the Wi-Fi Alliance specification "Proximity Ranging
(PR) Implementation Consideration Draft 1.9 Rev 1, section 5.3". Add
new FTM request attributes for min/max time between measurements,
nominal time (mandatory for NTB), AW duration, and total measurement
count.
Add NL80211_PMSR_PEER_ATTR_REQ_TYPE attribute using the new
nl80211_peer_measurement_ftm_req_type enum to allow userspace to
specify the ranging request type per peer:
- NL80211_PMSR_FTM_REQ_TYPE_INFRA: STA-to-AP or AP-to-STA ranging
(default if attribute is absent)
- NL80211_PMSR_FTM_REQ_TYPE_PD: peer-to-peer ranging
Validate the request type against the device TYPE_CAPS capabilities
advertised via NL80211_PMSR_FTM_CAPA_ATTR_TYPE_CAPS. Reject PD
requests if the device does not advertise PD support.
Reject PD requests that set trigger-based ranging, as TB ranging is
not compatible with peer-to-peer proximity detection.
Add ftms_per_burst limit of 4 for PD NTB ranging requests.
Signed-off-by: Peddolla Harshavardhan Reddy <peddolla.reddy@oss.qualcomm.com>
Link: https://patch.msgid.link/20260420090856.2152905-7-peddolla.reddy@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce Proximity Detection (PD) capabilities in Peer Measurement
Service (PMSR) as defined in the Wi-Fi Alliance specification
"Proximity Ranging (PR) Implementation Consideration Draft 1.9 Rev 1
section 3.3". This enables devices to advertise peer to peer ranging
support.
Restructure FTM capabilities in cfg80211_pmsr_capabilities to replace
the single support_rsta flag with nested ista and rsta sub-structs,
each carrying per-mode flags for Non-Trigger Based (NTB), Trigger Based
(TB), and EDCA based ranging. This allows drivers to advertise detailed
role and protocol support for both initiator and responder roles.
Add support to pass additional ISTA and RSTA role capabilities to
userspace using new nested ISTA_CAPS and RSTA_CAPS attributes. The
legacy RSTA_SUPPORT flag is retained for backward compatibility.
Add NL80211_PMSR_FTM_CAPA_ATTR_TYPE_CAPS nested attribute using the
nl80211_peer_measurement_ftm_type_capa enum with two sub-flags:
NL80211_PMSR_FTM_TYPE_CAPA_ATTR_INFRA_SUPPORT for STA-to-AP or
AP-to-STA ranging, and NL80211_PMSR_FTM_TYPE_CAPA_ATTR_PD_SUPPORT
for peer-to-peer ranging.
Add CONCURRENT_ISTA_RSTA_SUPPORT as a FTM capability flag indicating
the device can simultaneously act as initiator and responder in a
multi-peer measurement request.
Extend FTM capabilities with antenna configuration fields
(max_no_of_tx_antennas, max_no_of_rx_antennas) for the PR Element
during PASN negotiation, and ranging interval limits
(min_allowed_ranging_interval_edca, min_allowed_ranging_interval_ntb)
to advertise device timing constraints for EDCA and NTB-based ranging.
Update the FTM request validation path in pmsr.c to check RSTA
requests against the per-mode rsta capabilities (NTB, TB, EDCA),
rejecting requests for modes the device does not support.
Co-developed-by: Kavita Kavita <kavita.kavita@oss.qualcomm.com>
Signed-off-by: Kavita Kavita <kavita.kavita@oss.qualcomm.com>
Signed-off-by: Peddolla Harshavardhan Reddy <peddolla.reddy@oss.qualcomm.com>
Link: https://patch.msgid.link/20260420090856.2152905-6-peddolla.reddy@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the proximity detection (PD) interface type has no
start/stop commands defined, preventing user space from
controlling PD operations through the nl80211 interface.
Add NL80211_CMD_START_PD and NL80211_CMD_STOP_PD commands to
allow user space to start and stop a PD interface. Add the
corresponding start_pd and stop_pd operations to cfg80211_ops
and ieee80211_ops, along with nl80211 command handlers, rdev
wrappers, and tracing support. Validate that drivers advertising
PD interface support implement the required operations. Handle
PD interface teardown during device unregistration and when
the interface leaves the network.
Signed-off-by: Peddolla Harshavardhan Reddy <peddolla.reddy@oss.qualcomm.com>
Link: https://patch.msgid.link/20260420090856.2152905-5-peddolla.reddy@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new wdev-only interface type NL80211_IFTYPE_PD to support
Proximity Detection (PD) operations such as PASN and peer measurement
operations. This interface type operates without a netdev, similar to
P2P_DEVICE and NAN interfaces.
Implement support across cfg80211 and mac80211 layers with PD-specific
checks gated by the NL80211_EXT_FEATURE_SECURE_RTT feature flag,
management frame registration and transmission capabilities, and proper
channel context handling where PD interfaces are excluded from bandwidth
calculations. Update mac80211 to recognize the new interface type in the
relevant paths for this management-only interface.
PD discovery can be performed on any available interface, such as
NL80211_IFTYPE_STATION.
If PD/PMSR uses the MAC address of an existing interface type, such as
NL80211_IFTYPE_STATION, then pairing and measurement shall use that
same interface. If PD/PMSR uses a different MAC address, such as a
random MAC address, then pairing and measurement can be performed on a
new NL80211_IFTYPE_PD interface created with that random MAC address.
Signed-off-by: Peddolla Harshavardhan Reddy <peddolla.reddy@oss.qualcomm.com>
Link: https://patch.msgid.link/20260420090856.2152905-4-peddolla.reddy@oss.qualcomm.com
[fix comment style]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the remain_on_channel operation does not support
filtering incoming frames by destination MAC address. This
prevents use cases such as PASN authentication in the
responder side that need to receive frames addressed to a
specific MAC during the off-channel period.
Add an rx_addr parameter to the remain_on_channel operation
callback and propagate it through the call chain from nl80211
to driver implementations. Introduce the extended feature
NL80211_EXT_FEATURE_ROC_ADDR_FILTER as a capability gate so
that cfg80211 rejects the request if the driver does not
advertise support for address filtering. Extract the address
from the NL80211_ATTR_MAC attribute when provided in the
netlink message and update the tracing infrastructure to
include the address in remain_on_channel trace events. The
rx_addr parameter is optional and can be NULL, maintaining
backward compatibility with existing drivers.
Signed-off-by: Peddolla Harshavardhan Reddy <peddolla.reddy@oss.qualcomm.com>
Link: https://patch.msgid.link/20260420090856.2152905-3-peddolla.reddy@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The lmr_feedback field is only applicable to TB and non-TB ranging.
Currently, pmsr_parse_ftm() enforces lmr_feedback for all RSTA
requests, incorrectly rejecting valid EDCA-based RSTA requests.
Fix this by limiting the lmr_feedback requirement to TB and non-TB
ranging only.
Fixes: 853800c746 ("wifi: nl80211/cfg80211: support operating as RSTA in PMSR FTM request")
Co-developed-by: Kavita Kavita <kavita.kavita@oss.qualcomm.com>
Signed-off-by: Kavita Kavita <kavita.kavita@oss.qualcomm.com>
Signed-off-by: Peddolla Harshavardhan Reddy <peddolla.reddy@oss.qualcomm.com>
Link: https://patch.msgid.link/20260420090856.2152905-2-peddolla.reddy@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On AM62-LP-SK, the TPS65219 PMIC is the system power controller
responsible for handling system poweroff. Add the "system-power-controller"
property to the PMIC node to explicitly designate it as such.
Among all in-tree device trees using the TPS65219 PMIC (verified via
compatible string), AM62-LP-SK was the only one missing this property.
This patch corrects that omission.
This property will be used by the PMIC driver to conditionally register
the poweroff handler, ensuring only the designated power controller
registers for system poweroff operations.
Signed-off-by: Akashdeep Kaur <a-kaur@ti.com>
Link: https://patch.msgid.link/20260401112257.1248437-2-a-kaur@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add bootph-all property to vqmmc voltage regulator node and its
corresponding pinmux node to make it available during all boot
phases. This allows to run tuning early in SPL stages of boot.
Fixes: 8f023012eb ("arm64: dts: ti: k3-am62a: Enable UHS mode support for SD cards")
Cc: stable@vger.kernel.org
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://patch.msgid.link/20260324140247.1200631-1-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Use correct struct member names and formats to avoid kernel-doc
warnings:
Warning: include/linux/soc/ti/knav_dma.h:83 struct member 'priority' not
described in 'knav_dma_tx_cfg'
Warning: include/linux/soc/ti/knav_dma.h:113 struct member 'err_mode' not
described in 'knav_dma_rx_cfg'
Warning: include/linux/soc/ti/knav_dma.h:113 struct member 'desc_type' not
described in 'knav_dma_rx_cfg'
Warning: include/linux/soc/ti/knav_dma.h:113 struct member 'fdq' not
described in 'knav_dma_rx_cfg'
Warning: include/linux/soc/ti/knav_dma.h:127 struct member 'direction' not
described in 'knav_dma_cfg'
Warning: include/linux/soc/ti/knav_dma.h:127 struct member 'u' not
described in 'knav_dma_cfg'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260301011228.3064940-1-rdunlap@infradead.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Add support for detecting AM62P silicon revisions.
On AM62P, silicon revision is discovered with GP_SW1 register instead
of JTAGID register. Use the NVMEM framework to read GP_SW1 from the
gpsw-efuse nvmem provider to determine SoC revision.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20260209172330.53623-3-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add optional nvmem-cells and nvmem-cell-names properties to support
reading silicon revision information from alternate location using
NVMEM providers. This is used on AM62P to read GP_SW1 register for
accurate silicon revision detection.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260209172330.53623-2-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add support for Y8 and XYYY2101010 formats. We also need to add new csc
matrices for these y-only formats.
Reviewed-by: Vishal Sagar <vishal.sagar@amd.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patch.msgid.link/20260423-xilinx-formats-v10-9-c690c2b8ea89@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Use drm helpers, drm_format_info_plane_width(),
drm_format_info_plane_height() and drm_format_info_min_pitch() to
calculate sizes for the DMA.
This cleans up the code, but also makes it possible to support more
complex formats (like P030, P230).
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patch.msgid.link/20260423-xilinx-formats-v10-7-c690c2b8ea89@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Add XVUY2101010, a 10 bits per component YCbCr format in a 32 bit
container.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Vishal Sagar <vishal.sagar@amd.com>
Reviewed-by: Simon Ser <contact@emersion.fr>
Link: https://patch.msgid.link/20260423-xilinx-formats-v10-6-c690c2b8ea89@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Add T430, a 3 plane 10 bits per component non-subsampled YCbCr format.
A new initial letter was chosen for this one, as the format doesn't
match the existing P, Q or S formats. T is the next one in the alphabet.
It was definitely not chosen because of the initial letter in the
author's name.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Vishal Sagar <vishal.sagar@amd.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Simon Ser <contact@emersion.fr>
Link: https://patch.msgid.link/20260423-xilinx-formats-v10-5-c690c2b8ea89@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Add XYYY2101010 ("YPA4"), a 10 bit greyscale format, with 3 pixels
packed into 32-bit container, and two bits of padding.
The fourcc for the format is 'YPA4', which comes from Y - Y only, P -
packed, A - 10 (as in 0xA), 4 - 4 bytes.
Reviewed-by: Vishal Sagar <vishal.sagar@amd.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Simon Ser <contact@emersion.fr>
Link: https://patch.msgid.link/20260423-xilinx-formats-v10-4-c690c2b8ea89@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Add greyscale Y8 format.
The 8-bit greyscale format has been discussed before, and the earlier
guidance was to use DRM_FORMAT_R8, as a single-channel 8-bit pixel.
However, adding DRM_FORMAT_Y8 makes sense, we can mark it as 'is_yuv' in
the drm_format_info, and this can help the drivers handle e.g.
full/limited range. This will distinguish two single-channel formats:
R8, which is a RGB format with the same value for all components, and
Y8, which is a Y-only YCbCr format, with Cb and Cr being neutral.
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Reviewed-by: Vishal Sagar <vishal.sagar@amd.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Simon Ser <contact@emersion.fr>
Link: https://patch.msgid.link/20260423-xilinx-formats-v10-3-c690c2b8ea89@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Add a new pixel format, DRM_FORMAT_P230 ("P230")
P230 is 2 plane 10 bit per component YCbCr 2x1 subsampled format. P230
is similar to the already existing P030 format, which is 2x2 subsampled.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Vishal Sagar <vishal.sagar@amd.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Simon Ser <contact@emersion.fr>
Link: https://patch.msgid.link/20260423-xilinx-formats-v10-2-c690c2b8ea89@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
drm_format_info_bpp() cannot be used for formats which do not have an
integer bits-per-pixel in a pixel block.
E.g. DRM_FORMAT_P030's plane 0 has three 10-bit pixels (Y components),
and two padding bits, in a 4 byte block. That is 10.666... bits per
pixel when considering the whole 4 byte block, which is what
drm_format_info_bpp() does. Thus a driver that supports such formats
cannot use drm_format_info_bpp(),
It is a driver bug if this happens, but so handle wrong calls by
printing a warning and returning 0.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Acked-by: Simon Ser <contact@emersion.fr>
Link: https://patch.msgid.link/20260423-xilinx-formats-v10-1-c690c2b8ea89@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Since Rust uses GPUVM via the kernel crate, which is built-in, the GPUVM
module must also be built-in to use GPUVM from Rust. Adjust the Kconfig
settings accordingly.
Suggested-by: Danilo Krummrich <dakr@kernel.org>
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
Link: https://patch.msgid.link/20260427-gpuvm-config-v1-1-8ece03771f8a@google.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
