Mix the preferred osd (if any) into the placement seed that is fed into
the CRUSH object placement calculation. This prevents all the placement
pgs from peering with the same osds.
Rev the osd client protocol with this change.
Signed-off-by: Sage Weil <sage@newdream.net>
Must set filter selection as hardcoded coefficients for medium 3x3
filtering, which matches vbios setting for Ironlake.
This fixes display corrupt issue on HP arrandale with new vbios.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For new stepping of PCH, the display reference clock
is fully under driver's control. This one trys to setup
all needed reference clock for different outputs. Older
stepping of PCH chipset should be ignoring this.
This fixes output failure issue on newer PCH which requires
driver to take control of reference clock enabling.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This switches the U300 over from using a custom translate_vdd
function (which was just flipping blind bits in the hardware)
to using the regulator that actually controls the MMC voltage.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This defines regulator platform data and board power
regulator hogs for the ST-Ericsson U300 platform.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 75f4aa15cf.
We have a couple of platforms which require non-linear P:V mappings,
so we need these to be overridable.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some codec DAIs like stac9766, wm9712, wm9713, ad1980 don't register themselves
then it loses to the chance to be given a null_dai_ops in snd_soc_register_dai
if they have no ops. When functions like soc_pcm_open, soc_pcm_hw_params etc.
access the ops field in these DAIs, panic will happen.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the NULL test on jack is needed, then the derefernce should be after the
NULL test.
A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@match exists@
expression x, E;
identifier fld;
@@
* x->fld
... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Codec read/write functions: wait 21us between the pokings of hardware.
Add timeouts to unbounded loops waiting for bits to change.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Verify that the correct register has been received from the codec.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Do not rewrite the whole register, but only update the needed
bits in set_dai_sysclk functions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds performance event information about branches
and branch misses to the default output of perf stat.
Signed-off-by: Tim Blechmann <tim@klingt.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <4ADC3975.8050109@klingt.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Check for libelf headers and glibc headers separately so that
the error message correctly identifies which package
installation is missing/needed.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: paulus@samba.org
Cc: a.p.zijlstra@chello.nl
Cc: efault@gmx.de
Cc: fweisbec@gmail.com
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <4ADBCCE8.3060300@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add delay_secs sanity check to handle_keypress,
this fixes a division by zero crash.
Signed-off-by: Tim Blechmann <tim@klingt.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4AD9EBFD.106@klingt.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use DECLARE_BITMAP instead of an open coded array for our bitmap
of featured sections.
This makes the array an unsigned long instead of a u64 but since
we use a 256 bits bitmap, the array size shouldn't vary between
different boxes.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <1255795038-13751-1-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This provides a new set of bitmasked headers. A new field is
added in the perf headers that implements a bitmap storing
optional features present in the perf.data file.
The layout can be pictured like this:
(Usual perf headers)(Features bitmap)[Feature 0][Feature
n][Feature 255]
If the bit n is set, then the feature n is used in this file.
They are all set in order. This brings a backward and forward
compatibility.
The trace_info section has moved into such optional features,
this is the first and only one for now.
This is backward compatible with the .32 file version although
it doesn't support the previous separate trace.info file.
And finally it doesn't support the current interim development
version.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <1255792354-11304-2-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When we count both branches and branch-misses it is useful to
print out the percentage of branch-misses:
# perf stat -e branches -e branch-misses /bin/true
Performance counter stats for '/bin/true':
401684 branches # 0.000 M/sec
23301 branch-misses # 5.801 %
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: paulus@samba.org
Cc: a.p.zijlstra@chello.nl
LKML-Reference: <20091018112923.GQ4808@kryten>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently the SDIO part of the TX resources were initialized/released
with bus_dev_{start,stop}.
The generic code's TX subsystem is destroyed afterwards, so there is a
window from the bus-TX destruction to the generic-TX destruction where
the generic-TX code might call into bus-TX to do transactions.
The SDIO code cannot really cope with this (whereas in USB, how it is
laid out, it correctly ignores it). In any case, it made no sense for
the SDIO TX code to be in i2400m->bus_dev_start/stop(), so moved to
i2400m->bus_setup/release(), which also takes care of the oops.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
In coming commits, the i2400m SDIO driver will not use
i2400m->bus_dev_stop().
Thus changed to check before calling, as an empty stub has more
overhead than a call to check if the function pointer is non-NULL.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Current i2400m USB code had to threads (one for processing RX, one for
TX). When calling i2400m_{tx,rx}_release(), it would crash if the
thread had exited already due to an error.
So changed the code to have the thread fill in/out
i2400mu->{tx,rx}_kthread under a spinlock; then the _release()
function will call kthread_stop() only if {rx,tx}_kthread is still
set.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Currently __i2400m_dev_start was forcing, after uploading firmware and
doing a few checks to WIMAX_ST_UNINITIALIZED.
This can be overriding state changes that the device might have caused
by sending reports; thus it makes more sense to remove it and let the
device update the status on its own by sending reports.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
All the entry points into the TX module should check if the device has
been torn down. Otherwise, when the device resets or shuts down, there
are windows when a call to i2400m_tx*() will oops the system.
For that, make i2400m_tx_release() set i2400m->tx_buf to NULL under
the tx_lock. Then, any entry point [i2400m_tx(), _tx_msg_sent(),
_tx_msg_get()] will check for i2400m->tx_buf to be NULL and exit
gracefully.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The i2400m might start sending reports to the driver before it is done
setting up all the infrastructure needed for handling them.
Currently we were just dropping them when the driver wasn't ready and
that is bad in certain situations, as the sync between the driver's
idea of the device's state and the device's state dissapears.
This changes that by implementing a queue for handling
reports. Incoming reports are appended to it and a workstruct is woken
to process the list of queued reports.
When the device is not yet ready to handle them, the workstruct is not
woken, but at soon as the device becomes ready again, the queue is
processed.
As a consequence of this, i2400m_queue_work() is no longer used, and
thus removed.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Upcoming changes will have to add things to this function that expose
more internals, which would mean more forward declarators.
Frankly, it doesn't need to be an inline, so moved to driver.c, where
the declarations will be taken from the header file.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Since the addition of the pre/post reset handlers, it became clear
that we cannot do a I2400M-RT-BUS type reset while holding the
init_mutex, as in the case of USB, it will deadlock when trying to
call i2400m_pre_reset().
Thus, the following changes:
- clarify the fact that calling bus_reset() w/ I2400M_RT_BUS while
holding init_mutex is a no-no.
- i2400m_dev_reset_handle() will do a BUS reset to recover a gone
device after unlocking init_mutex.
- in the USB reset implementation, when cold and warm reset fails,
fallback to QUEUING a usb reset, not executing a USB reset, so it
happens from another context and does not deadlock.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The stop procedure for the device must make sure that any task that is
waiting on a message is properly cancelled.
This was being taken care of only by the __i2400m_dev_reset_handle()
path and the rest was working by chance because the waits have a
timeout.
Fixed by adding a proper cancellation in __i2400m_dev_stop().
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The actual fw->size may not equal to the bcf size indicated in
the bcf header if the extended bcf debug header is added in the tail.
To reflect the actual fw size that will be downloaded to the device,
it is now retrived from from the size field indicated in the bcf header.
All of the headers (if there are extended headers) should indicate same
value for the size field since only one set of firmware chunks is downloaded
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Both secure and non-secure boot must set the JUMP command in the
bootmode header as the last FW chunk, so we change to use the JUMP
command to decide if the FW chunk download is completed.
Since we tend to use one single FW to support both secure and non-secure
boot for most of the time, I2400M_BRH_SIGNED_JUMP is actually found
even for non-secure boot. But in case the FW does come with
I2400M_BRH_JUMP, we check for both of them in i2400m_dnload_bcf().
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Until now, calls to wimax_rfkill() will be blocked until the device is
at least past the WIMAX_ST_UNINITIALIZED state, return -ENOMEDIUM when
the device is in the WIMAX_ST_DOWN state.
In parallel, wimax-tools would issue a wimax_rfkill(WIMAX_RF_QUERY)
call right after opening a handle with wimaxll_open() as means to
verify if the interface is really a WiMAX interface [newer kernel
version will have a call specifically for this].
The combination of these two facts is that in some cases, before the
driver has finalized initializing its device's firmware, a
wimaxll_open() call would fail, when it should not.
Thus, change the wimax_rfkill() code to allow queries when the device
is in WIMAX_ST_UNINITIALIZED state.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
It makes sense that the messaging pipe to the device can be used
before the device is fully ready, as long as it is registered with the
stack. Some debugging tools need it.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
tcpdump and friends were not being able to decode packets sent via
WiMAX; they had a zero ethernet type, even when the stack was properly
sending them to the device with the right type.
It happens that the driver was overwriting the (fake) ethernet header
for creating the hardware header and that was bitting the cloning used
by tcpdump (et al) to look into the packets.
Use pkskb_expand_head() [method copied from the e1000 driver] to fix.
Thanks to Herbert Xu and Andi Kleen for helping to diagnose and
pointing to the right fix.
Cc: Herbert Xu <gondor.apana.org.au>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Missed a debug message that was being constantly printed as a
dev_err(); became annoying. Demote it to a debug message.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The USB stack can callback a driver is about to be reset by an
external entity and right after it, so the driver can save state and
then restore it.
This commit implements said support; it is implemented actually in the
core, bus-generic driver [i2400m_{pre,post}_reset()] and used by the
bus-specific drivers. This way the SDIO driver can also use it once
said support is brought to the SDIO stack.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
After the introduction of i2400m->bus_setup/release, there is no more
race condition where the bootmode buffers are needed before
i2400m_setup() is called.
Before, the SDIO driver would setup RX before calling i2400m_setup()
and thus need those buffers; now RX setup is done in
i2400m->bus_setup(), which is called by i2400m_setup().
Thus, all the bootmode buffer management can now be done completely
inside i2400m_setup()/i2400m_release(), removing complexity from the
bus-specific drivers.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The SDIO subdriver of the i2400m requires certain steps to be done
before we do any acces to the device, even for doing firmware upload.
This lead to a few ugly hacks, which basically involve doing those
steps in probe() before calling i2400m_setup() and undoing them in
disconnect() after claling i2400m_release(); but then, much of those
steps have to be repeated when resetting the device, suspending, etc
(in upcoming pre/post reset support).
Thus, a new pair of optional, bus-specific calls
i2400m->bus_{setup/release} are introduced. These are used to setup
basic infrastructure needed to load firmware onto the device.
This commit also updates the SDIO subdriver to use said calls.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The i2400m driver uses two different bits to distinguish how much the
driver is up. i2400m->ready is used to denote that the infrastructure
to communicate with the device is up and running. i2400m->updown is
used to indicate if 'ready' and the device is up and running, ready to
take control and data traffic.
However, all this was pretty dirty and not clear, with many open spots
where race conditions were present.
This commit cleans up the situation by:
- documenting the usage of both bits
- setting them only in specific, well controlled places
(i2400m_dev_start, i2400m_dev_stop)
- ensuring the i2400m workqueue can't get in the middle of the
setting by flushing it when i2400m->ready is set to zero. This
allows the report hook not having to check again for the bit to be
set [rx.c:i2400m_report_hook_work()].
- using i2400m->updown to determine if the device is up and running
instead of the wimax state in i2400m_dev_reset_handle().
- not loosing missed messages sent by the hardware before
i2400m->ready is set. In rx.c, whatever the device sends can be
sent to user space over the message pipes as soon as the wimax
device is registered, so don't wait for i2400m->ready to be set.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Currently the i2400m driver was starting in a weird way: registering a
network device, setting the device up and then registering a WiMAX
device.
This is an historic artifact, and was causing issues, a some early
reports the device sends were getting lost by issue of the wimax_dev
not being registered.
Fix said situation by doing the wimax device registration in
i2400m_setup() after network device registration and before starting
thed device.
As well, removed spurious setting of the state to UNINITIALIZED;
i2400m.dev_start() does that already.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
When the i2400m device needs to wake up an idle WiMAX connection, it
schedules a workqueue job to do it.
Currently, only when the network stack called the _stop() method this
work struct was being cancelled. This has to be done every time the
device is stopped.
So add a call in i2400m_dev_stop() to take care of such cleanup, which
is now wrapped in i2400m_net_wake_stop().
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Make sure that i2400m_dev_bootstrap() doesn't overwrite the last known
error code with -ENOENT; when a firmware fails to load, we want to
know the cause and not a generic error code.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Current driver didn't implement the .reset_resume method. The i2400m
normally always reset on a comeback from system standby/hibernation.
This requires previously applied commits to cache the firmware image
file.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
In preparation for a reset_resume implementation, have the firmware
image be cached in memory when the system goes to suspend and released
when out.
This is needed in case the device resets during suspend; the driver
can't load firmware until resume is completed or bad deadlocks
happen.
The modus operandi for this was copied from the Orinoco USB driver.
The caching is done with a kobject to avoid race conditions when
releasing it. The fw loader path is altered only to first check for a
cached image before trying to load from disk. A Power Management event
notifier is register to call i2400m_fw_cache() or i2400m_fw_uncache()
which take care of the actual cache management.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
In preparation for reset_resume support, in which the same code path
is going to be used, add a diagnostic message to dev_reset_handle()
that can be used to distinguish how the device got there.
This uses the new payload argument added to i2400m_schedule_work() by
the previous commit.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
