Add the rz_dmac_chan_is_paused() helper to check if the channel is paused.
This helper will be reused in subsequent patches.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-9-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the rz_dmac_chan_is_enabled() helper to check if a channel is
enabled. This helper will be reused in subsequent patches.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-8-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Save the start LM descriptor to avoid starting from the beginning of the
channel's LM descriptor list in rz_dmac_calculate_residue_bytes_in_vd().
This avoids unnecessary iterations.
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-7-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a the rz_dmac_lmdesc_addr() helper function to compute the lmdesc
address, to make the code easier to understand. The helper will be used in
subsequent patches.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-6-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use rz_dmac_disable_hw() instead of open coding it. This unifies the
code and prepares it for the addition of suspend to RAM and cyclic DMA.
The rz_dmac_disable_hw() from rz_dmac_chan_probe() was moved after
vchan_init() as it initializes the channel->vc.chan.device used in
rz_dmac_disable_hw().
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-5-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use list_first_entry_or_null() instead of open-coding it with a
list_empty() check and list_first_entry(). This simplifies the code.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-4-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
list_first_entry() does not return NULL when the list is empty,
making the existing NULL check invalid. Use list_first_entry_or_null()
instead.
Fixes: 21323b118c ("dmaengine: sh: rz-dmac: Add device_tx_status() callback")
Cc: stable@vger.kernel.org
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-3-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Once the interrupt is requested, the interrupt handler may run immediately.
Since the IRQ handler can access channel->ch_base, which is initialized
only after requesting the IRQ, this may lead to invalid memory access.
Likewise, the IRQ thread may access uninitialized data (the ld_free,
ld_queue, and ld_active lists), which may also lead to issues.
Request the interrupts only after everything is set up. To keep the error
path simpler, use dmam_alloc_coherent() instead of dma_alloc_coherent().
Fixes: 5000d37042 ("dmaengine: sh: Add DMAC driver for RZ/G2L SoC")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260526084710.3491480-2-claudiu.beznea@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add compatible and chip data to support GPCDMA in Tegra264, which has
differences in register layout and address bits compared to previous
versions.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260331102303.33181-10-akhilrajeev@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use 'iommu-map', when provided, to get the stream ID to be programmed
for each channel. Iterate over the channels registered and configure
each channel device separately using of_dma_configure_id() to allow
it to use a separate IOMMU domain for the transfer. However, do this
in a second loop since the first loop populates the DMA device channels
list and async_device_register() registers the channels. Both are
prerequisites for using the channel device in the next loop.
Channels will continue to use the same global stream ID if the
'iommu-map' property is not present in the device tree.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260331102303.33181-9-akhilrajeev@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Switch to managed registration in probe. This simplifies the error
paths in the probe and also removes the requirement of the driver
remove function.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Suggested-by: Frank Li <frank.li@nxp.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260331102303.33181-8-akhilrajeev@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Tegra264 supports address width of 41 bits. Unlike older SoCs which use
a common high_addr register for upper address bits, Tegra264 has separate
src_high and dst_high registers to accommodate this wider address space.
Add an addr_bits property to the device data structure to specify the
number of address bits supported on each device and use that to program
the appropriate registers.
Update the sg_req struct to remove the high_addr field and use
dma_addr_t for src and dst to store the complete addresses. Extract
the high address bits only when programming the registers.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260331102303.33181-7-akhilrajeev@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Repurpose the struct tegra_dma_channel_regs to define offsets for all the
channel registers. Previously, the struct only held the register values
for each transfer and was wrapped within tegra_dma_sg_req. Move the
values directly into tegra_dma_sg_req and use channel_regs for
storing the register offsets. Update all register reads/writes to use
the struct channel_regs. This prepares for the register offset change
in Tegra264.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260331102303.33181-6-akhilrajeev@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On Tegra264, reset is not available for the driver to control as
this is handled by the boot firmware. Hence make the reset control
optional and update the error message to reflect the correct error.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260331102303.33181-5-akhilrajeev@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are multi spba-busses for i.MX8M* platforms, if only search for
the first spba-bus in DT, the found spba-bus may not the real bus of
audio devices, which cause issue for sdma p2p case, as the sdma p2p
script presently does not deal with the transactions involving two devices
connected to the AIPS bus.
Search the SDMA parent node first, which should be the AIPS bus, then
search the child node whose compatible string is spba-bus under that AIPS
bus for the above multi spba-busses case.
Fixes: 8391ecf465 ("dmaengine: imx-sdma: Add device to device support")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260407032755.2758049-1-shengjiu.wang@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
By convention MODULE_DEVICE_TABLE() immediately follows the ID table it
exports, because this is easier to read and verify. It also makes more
sense since #ifdef for ACPI or OF could hide both of them.
Most of the drivers already have this correctly placed, so adjust
the missing ones. No functional impact.
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260514060525.9253-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
SpacemiT K3 reuses most of the PDMA IP design found on K1, with one
difference being the extended DRCMR base address. Add "spacemit,k3-pdma"
compatible string and define a new mmp_pdma_ops for K3 PDMA.
Signed-off-by: Guodong Xu <guodong@riscstar.com>
Signed-off-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Link: https://patch.msgid.link/20260518-k3-pdma-v6-3-67fdf319a8f8@linux.spacemit.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Refactor the DRCMR macro into a helper function mmp_pdma_get_drcmr()
to support variable extended DRCMR base addresses across different PDMA
implementations, such as SpacemiT K3.
Signed-off-by: Guodong Xu <guodong@riscstar.com>
Signed-off-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Link: https://patch.msgid.link/20260518-k3-pdma-v6-2-67fdf319a8f8@linux.spacemit.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
AMD MDB IP supports Linked List (LL) mode as well as non-LL mode.
The current code does not have the mechanisms to enable the
DMA transactions using the non-LL mode. The following two cases
are added with this patch:
- For the AMD (Xilinx) only, when a valid physical base address of
the device side DDR is not configured, then the IP can still be
used in non-LL mode. For all the channels DMA transactions will
be using the non-LL mode only. This, the default non-LL mode,
is not applicable for Synopsys IP with the current code addition.
- If the default mode is LL-mode, for both AMD (Xilinx) and Synosys,
and if user wants to use non-LL mode then user can do so via
configuring the peripheral_config param of dma_slave_config.
Signed-off-by: Devendra K Verma <devendra.verma@amd.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260318070403.1634706-3-devendra.verma@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
AMD MDB PCIe endpoint support. For AMD specific support
added the following
- AMD supported PCIe Device IDs and Vendor ID (Xilinx).
- AMD MDB specific driver data
- AMD MDB specific VSEC capability to retrieve the device DDR
base address.
Signed-off-by: Devendra K Verma <devendra.verma@amd.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260318070403.1634706-2-devendra.verma@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are a couple of spelling mistakes, one in a comment block and
one in a module description. Fix them.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://patch.msgid.link/20260317204631.120332-1-colin.i.king@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This DMA controller appears in Loongson-2K0300 and Loongson-2K3000.
It is a chain multi-channel controller that enables data transfers from
memory to memory, device to memory, and memory to device, as well as
channel prioritization configurable through the channel configuration
registers.
In addition, there are slight differences between Loongson-2K0300 and
Loongson-2K3000, such as channel register offsets and the number of
channels.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://patch.msgid.link/73bc32ba6249f1eef94fec9b349bc9efa98278ea.1772853681.git.zhoubinbin@loongson.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use guard() and scoped_guard() infrastructure instead of explicitly
acquiring and releasing spinlocks to simplify the code and ensure that
all locks are released properly.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://patch.msgid.link/fb59bb25e5c4fcb84d9aa7b351285fa8d02ea8cb.1772853681.git.zhoubinbin@loongson.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A single AXIDMA controller can have one or two channels. When it has two
channels, the reset for both are tied together: resetting one channel
resets the other as well. This creates a problem where resetting one
channel will reset the registers for both channels, including clearing
interrupt enable bits for the other channel, which can then lead to
timeouts as the driver is waiting for an interrupt which never comes.
The driver currently has a probe-time work around for this: when a
channel is created, the driver also resets and enables the
interrupts. With two channels the reset for the second channel will
clear the interrupt enables for the first one. The work around in the
driver is just to manually enable the interrupts again in
xilinx_dma_alloc_chan_resources().
This workaround only addresses the probe-time issue. When channels are
reset at runtime (e.g., in xilinx_dma_terminate_all() or during error
recovery), there's no corresponding mechanism to restore the other
channel's interrupt enables. This leads to one channel having its
interrupts disabled while the driver expects them to work, causing
timeouts and DMA failures.
A proper fix is a complicated matter, as we should not reset the other
channel when it's operating normally. So, perhaps, there should be some
kind of synchronization for a common reset, which is not trivial to
implement. To add to the complexity, the driver also supports other DMA
types, like VDMA, CDMA and MCDMA, which don't have a shared reset.
However, when the two-channel AXIDMA is used in the (assumably) normal
use case, providing DMA for a single memory-to-memory device, the common
reset is a bit smaller issue: when something bad happens on one channel,
or when one channel is terminated, the assumption is that we also want
to terminate the other channel. And thus resetting both at the same time
is "ok".
With that line of thinking we can implement a bit better work around
than just the current probe time work around: let's enable the
AXIDMA interrupts at xilinx_dma_start_transfer() instead.
This ensures interrupts are enabled whenever a transfer starts,
regardless of any prior resets that may have cleared them.
This approach is also more logical: enable interrupts only when needed
for a transfer, rather than at resource allocation time, and, I think,
all the other DMA types should also use this model, but I'm reluctant to
do such changes as I cannot test them.
The reset function still enables interrupts even though it's not needed
for AXIDMA anymore, but it's common code for all DMA types (VDMA, CDMA,
MCDMA), so leave it unchanged to avoid affecting other variants.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Fixes: c0bba3a99f ("dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine")
Link: https://patch.msgid.link/20260311-xilinx-dma-fix-v2-1-a725abb66e3c@ideasonboard.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The segment .control and .status fields both contain top bits which are
not part of the buffer size, the buffer size is located only in the bottom
max_buffer_len bits. To avoid interference from those top bits, mask out
the size using max_buffer_len first, and only then subtract the values.
Fixes: a575d0b4e6 ("dmaengine: xilinx_dma: Introduce xilinx_dma_get_residue")
Signed-off-by: Marek Vasut <marex@nabladev.com>
Link: https://patch.msgid.link/20260316222530.163815-1-marex@nabladev.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The cyclic DMA calculation is currently entirely broken and reports
residue only for the first segment. The problem is twofold.
First, when the first descriptor finishes, it is moved from active_list
to done_list, but it is never returned back into the active_list. The
xilinx_dma_tx_status() expects the descriptor to be in the active_list
to report any meaningful residue information, which never happens after
the first descriptor finishes. Fix this up in xilinx_dma_start_transfer()
and if the descriptor is cyclic, lift it from done_list and place it back
into active_list list.
Second, the segment .status fields of the descriptor remain dirty. Once
the DMA did one pass on the descriptor, the .status fields are populated
with data by the DMA, but the .status fields are not cleared before reuse
during the next cyclic DMA round. The xilinx_dma_get_residue() recognizes
that as if the descriptor was complete and had 0 residue, which is bogus.
Reinitialize the status field before placing the descriptor back into the
active_list.
Fixes: c0bba3a99f ("dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine")
Signed-off-by: Marek Vasut <marex@nabladev.com>
Link: https://patch.msgid.link/20260316221943.160375-1-marex@nabladev.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Unlike chan->direction , struct dma_device .directions field is a
bitfield. Turn chan->direction into a bitfield to make it compatible
with struct dma_device .directions .
Fixes: 7e01511443 ("dmaengine: xilinx_dma: Set dma_device directions")
Signed-off-by: Marek Vasut <marex@nabladev.com>
Link: https://patch.msgid.link/20260316221728.160139-1-marex@nabladev.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The RZ/G2L SCIFA driver uses dmaengine_prep_slave_sg() to enqueue DMA
transfers and implements a timeout mechanism on RX to handle cases where
a DMA transfer does not complete. The timeout is implemented using an
hrtimer.
In the hrtimer callback, dmaengine_tx_status() is called (along with
dmaengine_pause()) to retrieve the transfer residue and handle incomplete
DMA transfers.
Add support for device_{pause, resume}() callbacks.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20260316133252.240348-9-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The RZ/G2L SCIFA driver uses dmaengine_prep_slave_sg() to enqueue DMA
transfers and implements a timeout mechanism on RX to handle cases where
a DMA transfer does not complete. The timeout is implemented using an
hrtimer.
In the hrtimer callback, dmaengine_tx_status() is called (along with
dmaengine_pause()) to retrieve the transfer residue and handle incomplete
DMA transfers.
Add support for the device_tx_status() callback.
Co-developed-by: Long Luu <long.luu.ur@renesas.com>
Signed-off-by: Long Luu <long.luu.ur@renesas.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Co-developed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260316133252.240348-8-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
rz_lmdesc_setup() invalidates DMA descriptors more comprehensively.
It resets the base, head, and tail pointers of the descriptor list and
clears the descriptor headers and their NXLA pointers. Use
rz_lmdesc_setup() instead of open-coding parts of its logic.
Signed-off-by: John Madieu <john.madieu.xa@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260316133252.240348-7-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
rz_dmac_enable_hw() calls local_irq_save()/local_irq_restore(), but
this is not needed because the callers of rz_dmac_enable_hw() already
protect the critical section using
spin_lock_irqsave()/spin_lock_irqrestore().
Remove the local_irq_save()/local_irq_restore() calls.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20260316133252.240348-6-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The CHCTRL register has 11 bits that can be updated by software. The
documentation for all these bits states the following:
- A read operation results in 0 being read
- Writing zero does not affect the operation
All bits in the CHCTRL register accessible by software are set and clear
bits.
The documentation for the CLREND bit of CHCTRL states:
Setting this bit to 1 can clear the END bit of the CHSTAT_n/nS register.
Also, the DMA transfer end interrupt is cleared. An attempt to read this
bit results in 0 being read.
1: Clears the END bit.
0: Does not affect the operation.
Since writing zero to any bit in this register does not affect controller
operation and reads always return zero, there is no need to perform
read-modify-write accesses to set the CLREND bit. Drop the read of the
CHCTRL register.
Also, since setting the CLREND bit does not interact with other
functionalities exposed through this register and only clears the END
interrupt, there is no need to lock around this operation. Add a comment
to document this.
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20260316133252.240348-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Both rz_dmac_disable_hw() and rz_dmac_irq_handle_channel() update the
CHCTRL register. To avoid concurrency issues when configuring
functionalities exposed by this registers, take the virtual channel lock.
All other CHCTRL updates were already protected by the same lock.
Previously, rz_dmac_disable_hw() disabled and re-enabled local IRQs, before
accessing CHCTRL registers but this does not ensure race-free access.
Remove the local IRQ disable/enable code as well.
Fixes: 5000d37042 ("dmaengine: sh: Add DMAC driver for RZ/G2L SoC")
Cc: stable@vger.kernel.org
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20260316133252.240348-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver lists (ld_free, ld_queue) are used in
rz_dmac_free_chan_resources(), rz_dmac_terminate_all(),
rz_dmac_issue_pending(), and rz_dmac_irq_handler_thread(), all under
the virtual channel lock. Take the same lock in rz_dmac_prep_slave_sg()
and rz_dmac_prep_dma_memcpy() as well to avoid concurrency issues, since
these functions also check whether the lists are empty and update or
remove list entries.
Fixes: 5000d37042 ("dmaengine: sh: Add DMAC driver for RZ/G2L SoC")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20260316133252.240348-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
At the end of this function, d is the traversal cursor of flist, but the
code completes found instead. This can lead to issues such as NULL pointer
dereferences, double completion, or descriptor leaks.
Fix this by completing d instead of found in the final
list_for_each_entry_safe() loop.
Fixes: aa8d18becc ("dmaengine: idxd: add callback support for iaa crypto")
Signed-off-by: Tuo Li <islituo@gmail.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://patch.msgid.link/20260106032428.162445-1-islituo@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Renesas RZ/T2H (R9A09G077) and RZ/N2H (R9A09G087) SoCs use a
completely different ICU unit compared to RZ/V2H, which requires a
separate implementation.
Add support for them.
RZ/N2H will use RZ/T2H as a fallback.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260105114445.878262-5-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Renesas RZ/T2H (R9A09G077) and RZ/N2H (R9A09G087) SoCs use a
completely different ICU unit compared to RZ/V2H, which requires a
separate implementation.
To prepare for adding support for these SoCs, add a chip-specific
structure and put a pointer to the rzv2h_icu_register_dma_req() function
in the .register_dma_req field of the chip-specific structure to allow
for other implementations. Do the same for the default request value,
RZV2H_ICU_DMAC_REQ_NO_DEFAULT, and place it into .dma_req_no_default.
While at it, factor out the logic that calls .register_dma_req() or
rz_dmac_set_dmars_register() into a separate function to remove some
code duplication.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260105114445.878262-3-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Renesas RZ/T2H (R9A09G077) and RZ/N2H (R9A09G087) SoCs do not have
an error interrupt for the DMACs, and the current driver implementation
does not make much use of it.
To prepare for adding support for these SoCs, do not error out if the
error interrupt is missing.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260105114445.878262-2-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use managed API devm_kzalloc(), dmaenginem_async_device_register() and
devm_of_dma_controller_register() to simple code.
No functional change.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260225-mxsdma-module-v3-9-8f798b13baa6@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>