Add MT26438 (ConnectX EN 40GigE PCIe 2.0 5GT/s) to the list of supported
devices.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This small typo written by author causes that McBSP receiver is disabled on
OMAP2430 and OMAP3430 even if only transmitter is stopped. This was noted
with ALSA SoC where simultaneous recording halted if playback was stopped
first.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch initializes the correct SDRC settings required
for DVFS on Zoom2.
Signed-off-by: Teerth Reddy <teerth@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The I2C-1 bus frequency on RX-51 should be 2.2 MHz. The speed is limited
by TWL5030/GAIA; a higher speed could lead to errors on the interface. The
maximum speed depends on the system clock for GAIA: 2.2 MHz (if 19.2 MHz),
2.4 MHz (26 MHz) or 2.9 MHz (38.4 MHz).
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Argument tparams was not being used to program
global register GCR.HI_THREAD_RESERVED. This patch fixes the same.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The symbol CONFIG_ISP1301_OMAP was defined twice in the
defconfig. This was causing the warning:
arch/arm/configs/omap3_beagle_defconfig:972:warning:
override: reassigning to symbol ISP1301_OMAP
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tune/fix early timer expiry handling and return correct early timeout value
for set_next_event.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
LKML-Reference: <20091014141630.GB11048@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The ALC662/663 parser calls wrongly alc880_auto_create_input_ctls()
to check the capture source selections. This should be alc882, instead.
Reference: Novell bnc#546918
http://bugzilla.novell.com/show_bug.cgi?id=546918
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This way all flush_to_ldisc work is always done through the workqueues,
and we thus have a single point of serialization.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's safe to remove the BKL from nvram_open(): there's no open()
versus read() races: nvram_init() is very simple and race-free,
it registers the device then puts it into /proc - there's no
state init to race with.
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <1255116426-7270-1-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
48 kHz limit is for slightly better stability, and sample rates other
than 48k (like 96k/192k) are for better sound quality.
We choose better quality, so remove the 48k limit.
Signed-off-by: Logan Li <loganli@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Remove the BKL from agp_open
- Perform a few clean-ups.
Analysis:
---------
int minor is local to the function.
The following are protected by agp_fe.agp_mutex
struct agp_file_private *priv;
struct agp_client *client;
Call-outs:
kzalloc should be safe to call under the mutex_lock
agp_find_client_by_pid:
- agp_mmap calls that under agp_fe.agp_mutex which we hold in agp_open
- agpioc_reserve_wrap calls it without any locking what-so-ever.
- Is that an error? Or is that okay because it has pid that is
a unique handle?
agp_insert_file_private:
- This function only manipulates struct agp_file_private, once again
while agp_fe.agp_mutex is held
Signed-off-by: John Kacur <jkacur@redhat.com>
Acked-by: David Airlie <airlied@linux.ie>
LKML-Reference: <alpine.LFD.2.00.0910112216060.12574@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
cycle_kernel_lock() got pushed down to ipath_open(). I tried hard to
understand what it might protect, but finally gave up.
Roland noted that qlogic seems to have abandoned the ipath driver and
came to the following wise conclusion: "So I guess if the BKL stuff is
blocking you in any way, we can just drop it from ipath and leave it
as yet another race condition in a rotting old driver."
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <adad44tj090.fsf@cisco.com>
Cc: Roland Dreier <rdreier@cisco.com>
cycle_kernel_lock() was added during the big BKL pushdown. It should
ensure the serializiation against driver init code.
tb0219_base is initialized before the character device is
registered, but the spinlock is not initialized.
Initialize the spinlock statically and remove cycle_kernel_lock().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <20091010153350.222654356@linutronix.de>
Cc: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
cycle_kernel_lock() was added during the big BKL pushdown. It should
ensure the serializiation against driver init code. In this case there
is nothing to serialize. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <20091010153350.167321547@linutronix.de>
Acked-by: Jim Cromie <jim.cromie@gmail.com>
cycle_kernel_lock() was added during the big BKL pushdown. It should
ensure the serializiation against driver init code. In this case there
is nothing to serialize. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <20091010153350.127093710@linutronix.de>
Acked-by: Jim Cromie <jim.cromie@gmail.com>
Remove the empty ioctl and the cycle_kernel_lock() in
eisa_eeprom_open() which got there with the big BKL push down. There
is nothing to wait for and sychronize with after the misc device has
been registered.
Remove the empty ioctl as well. The generic code handles the -ENOTTY
if no ioctl function is provided.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <20091010153350.086917493@linutronix.de>
Cc: Kyle McMartin <kyle@parisc-linux.org>
BKL locking came to efirtc via the big BKL push down, but the access
to the efi functions is protected by efi_rtc_lock already.
Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <20091010153350.046644063@linutronix.de>
cycle_kernel_lock() was added during the big BKL pushdown. It should
ensure the serializiation against driver init code. In this case there
is nothing to serialize. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <20091010153349.884891604@linutronix.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
hw_random core is completely serialized with rng_mutex. No need for
the cycle_kernel_lock() magic.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <20091010153349.844488872@linutronix.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
The ans-lcd driver got the cycle_kernel_lock() in anslcd_open() from
the BKL pushdown and it still uses the locked ioctl.
The BKL serialization in this driver is more than obscure and
definitely does not cover all possible corner cases. Protect the
access to the hardware with a local mutex and get rid of BKL and
locked ioctl.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <20091010153349.966159859@linutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Drop the bkl from nvram_llseek() as it obviously protects nothing.
The file offset is safe in essence.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <1255116426-7270-1-git-send-email-fweisbec@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is nothing to protect inside nvram_llseek(), the file
offset doesn't need to be protected and nvram_len is only
initialized from an __init path.
It's safe to remove the big kernel lock there.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <1255116030-6929-1-git-send-email-fweisbec@gmail.com>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The generic open callback for the mem class devices is "protected" by
the bkl.
Let's look at the datas manipulated inside memory_open:
- inode and file: safe
- the devlist: safe because it is constant
- the memdev classes inside this array are safe too (constant)
After we find out which memdev file operation we need to use, we call
its open callback. Depending on the targeted memdev, we call either
open_port() that doesn't manipulate any racy data (just a capable()
check), or we call nothing.
So it's safe to remove the big kernel lock there.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <1255113062-5835-1-git-send-email-fweisbec@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The BKL was added there with the big pushdown. Remove it as the code
is serialized already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <20091010153349.318535932@linutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
The big BKL pushdown added cycle_kernel_lock(). There is nothing to
wait for in this driver. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <20091010153349.277882707@linutronix.de>
misc_open() is already serialized with misc_mtx. Remove the BKL
locking which got there via the BKL pushdown.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
LKML-Reference: <20091010153349.237173041@linutronix.de>
This looks like a cut-and-paste from functionality that no-longer
needs the bkl Just remove it. Also, rewrite slightly so that it looks
closer to sys_execve on other architectures.
Signed-off-by: John Kacur <jkacur@redhat.com>
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
LKML-Reference: <alpine.LFD.2.00.0910130016540.3658@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This looks like a copy-and-paste of functionality that no-longer needs
the bkl. Just remove it.
Signed-off-by: John Kacur <jkacur@redhat.com>
Reviewed: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
LKML-Reference: <alpine.LFD.2.00.0910130014520.3658@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This seems like a copy-and-paste from code that no-longer needs the
BKL Just remove it.
Signed-off-by: John Kacur <jkacur@redhat.com>
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <alpine.LFD.2.00.0910130011180.3658@localhost.localdomain>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This looks like a copy-and-paste job for code that no-longer needs the
BKL Just remove it.
Signed-off-by: John Kacur <jkacur@redhat.com>
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
LKML-Reference: <alpine.LFD.2.00.0910130010000.3658@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
sys_execve for frv seems to be a copy-and-paste of sys_execve that no
longer requires the bkl. Just remove it.
Signed-off-by: John Kacur <jkacur@redhat.com>
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: David Howells <dhowells@redhat.com>
LKML-Reference: <alpine.LFD.2.00.0910130008320.3658@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This looks like a cut-and-paste job. For example, compare this
function to sys_execve in arch/x86/kernel/process_64.c and it is
almost line by line the same, except the one in x86 nolonger has the
big kernel lock. All of the functions called between the lock are
generic and not specific to blackfin - thus, I believe it is safe to
remove the bkl here.
Signed-off-by: John Kacur <jkacur@redhat.com>
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
LKML-Reference: <alpine.LFD.2.00.0910130007240.3658@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The lock/unlock kernel pair in do_open() got there with the BKL push
down and protects nothing. Remove it.
Replace the lock/unlock kernel in the ioctl code with a mutex to
protect standbys_pending and suspends_pending.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <20091010153349.365236337@linutronix.de>
cycle_lock_kernel() in microcode_open() is a worthless exercise as
there is nothing to wait for. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <20091010153349.196074920@linutronix.de>
We have an optimization in btrfs to allow blocks to be
immediately freed if they were allocated in this transaction and never
written. Otherwise they are pinned and freed when the transaction
commits.
This isn't optimal for discard mode because immediately freeing
them means immediately discarding them. It is better to give the
block to the pinning code and letting the (slow) discard happen later.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The discard support code in btrfs currently is guarded by ifdefs for
BIO_RW_DISCARD, which is never defines as it's the name of an enum
memeber. Just remove the useless ifdefs to actually enable the code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Enable discard by default is not a good idea given the the trim speed
of SSD prototypes we've seen, and the carecteristics for many high-end
arrays. Turn of discards by default and require the -o discard option
to enable them on.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
A recently fsync optimization make btrfs_sync_log skip calling
wait_for_writer in the single log writer case. This is incorrect
since the writer count can also be increased by btrfs_pin_log.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
There's a problem where we don't do any space reservation for truncates, which
can cause you to OOPs because you will be allowed to go off in the weeds a bit
since we don't account for the delalloc bytes that are created as a result of
the truncate.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
cycle_kernel_lock() was added during the big BKL pushdown. It should
ensure the serializiation against driver init code.
mmapper_open() cannot be called before misc_register() succeeded, but
p_buf might be uninitialized.
Move the initialization of p_buf before the misc_register() call and
get rid of cycle_kernel_lock().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <20091010153349.682213670@linutronix.de>
Cc: Jeff Dike <jdike@addtoit.com>
cycle_kernel_lock() was added during the big BKL pushdown. It should
ensure the serializiation against driver init code. In this case there
is nothing to serialize. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <20091010153349.641118498@linutronix.de>
Cc: Jeff Dike <jdike@addtoit.com>
cycle_kernel_lock() was added during the big BKL pushdown. It should
ensure the serializiation against driver init code. In this case there
is nothing to serialize. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
LKML-Reference: <20091010153349.601625576@linutronix.de>
Acked-by: Jan Glauber <jang@linux.vnet.ibm.com>