We are still largely using the old ethtool API macros. This is
problematic because eventually they will be removed and they only
support 32 bits of PHY types.
This overhauls i40e_phy_type_to_ethtool to use only the new API. Doing
this also allows us to provide much better support for newer 25G and 10G
PHY types which is included here as well.
The remaining usages of the old ethtool API will be addressed in other
patches in the series.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for 25G Active Optical Cables (AOC) and Active
Copper Cables (ACC) PHY types.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Signed-off-by: Krzysztof Malek <krzysztof.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This separates the setting of autoneg in i40e_phy_types_to_ethtool into
its own conditional. Doing this adds clarity as what PHYs
support/advertise autoneg and makes it easier to add new PHY types in
the future.
This also fixes an issue on devices with CRT_RETIMER where advertising
autoneg was being set, but supported autoneg was not.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's a number of minor incidental whitespace issues in this file.
This addresses most of the ones I could find.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Someone forgot a word in this comment and it's confusing without it.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function header erroneously listed 'phy_types' as a parameter. The
correct parameter is 'pf'.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes two issues in i40e_get_link_ksettings. It adds calls to
ethtool_link_ksettings_zero_link_mode to make sure advertising and
supported link masks are cleared before we start setting bits in them.
This also replaces some funky bit manipulations with a much nicer call
to ethtool_link_ksettings_del_link_mode when removing link modes.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Someone left this poor little function naked with no header. This
dresses it up in a proper function header it deserves.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This 'ifdef' doesn't accomplish anything so remove it.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After the switch to the new ethtool API, ethtool passes us
ethtool_ksettings structs instead of ethtool_command structs, however we
were still referring to them as 'cmd' variables. This renames them to
'ks' variables which makes the code easier to understand.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Formerly, IPIP entries were created lazily by next hops that referenced
an offloadable IP-in-IP netdevice. However now that they are created
eagerly as a reaction to events on such netdevices, the reference
counting is useless. Hence drop it.
The routes whose next hops reference an offloaded IP-in-IP netdevice
actually linger around a bit after their device is unregistered.
However, mlxsw_sp_ipip_entry_destroy() also destroys the backing
loopback, and mlxsw_sp_rif_destroy() transitively (via
mlxsw_sp_nexthop_rif_gone_sync()) calls mlxsw_sp_nexthop_ipip_fini(),
which unlinks the IPIP entry from a next hop. Thus no dangling pointers
are left behind for the brief window after netdevice is gone, but routes
not yet.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPIP entries are created as soon as an offloadable device is created.
That means that when such a device is later moved to a different VRF,
the loopback device that backs the tunnel is wrong.
Thus when an offloadable encapsulating netdevice moves from one VRF to
another, make sure that the loopback is updated as necessary.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code for offloading IP-in-IP tunneling assumes that there is no
decap without encap. But that's never true for IPv6 overlays, and is not
true for IPv4 ones either, if net.ipv4.conf.*.rp_filter is unset.
To support decap-only tunnels, an IPIP entry is now created as soon as
an offloadable tunneling device is created. When that netdevice is up'd,
a decap route is looked up and possibly offloaded. Thus decap is not
handled implicitly as part of mlxsw_sp_ipip_entry_get() call anymore,
but needs to be done explicitly after the get, if desired.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, all netdevice notifications that the driver cared about were
related to its own ports, and mlxsw_sp could be retrieved from the
netdevice's private data. For IP-in-IP offloading however, the driver
cares about events on foreign netdevices, and getting at mlxsw_sp or
router data structures from the handler is inconvenient.
Therefore move the netdevice notifier blocks from global scope to struct
mlxsw_sp to allow retrieval from the notifier block pointer itself.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The notifier cause a link error when NET_DSA is a loadable
module:
drivers/net/ethernet/broadcom/bcmsysport.o: In function `bcm_sysport_remove':
bcmsysport.c:(.text+0x1582): undefined reference to `unregister_dsa_notifier'
drivers/net/ethernet/broadcom/bcmsysport.o: In function `bcm_sysport_probe':
bcmsysport.c:(.text+0x278d): undefined reference to `register_dsa_notifier'
This adds a dependency that forces the systemport driver to be
a loadable module as well when that happens, but otherwise
allows it to be built normally when DSA is either built-in or
completely disabled.
Fixes: d156576362 ("net: systemport: Establish lower/upper queue mapping")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify baycom driver to use the new parallel port device model.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes custom flag handling.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-updates-2017-10-11: IPoIB Multi Pkey support
This series provides the support for IPoIB Multi Pkey.
InfiniBand Pkeys are the equivalent of Ethernet vlans.
Currently IPoIB device driver supports only default Pkey and IPoIB Pkey child
interfaces are not supported with IPoIB offloads mode, this series will add
the support for that by allowing creating mlx5 multiple IPoIB netdevices with
a non-default Pkey.
mlx5 IPoIB Pkey child interface is smaller version of mlx5i IPoIB interfaces and shares
most of its resources with the parent IPoIB interface, namely RX steering and ring
queue resources.
The only mlx5 resources a child Pkey interface will be creating are the TX rings,
since they should be assigned to a specific Pkey.
mlx5i Pkey netdev is implemented via new mlx5e netdev profile implemented in
mlx5/core/ipoib/ipoib_vlan.c.
The series starts with a refactoring of mlx5e PTP and mlx5 clock implementation
to move the code to be part of mlx5 core rather than mlx5e netdevice, in order to
make mlx5 clock and PTP registration part of the core to be shared with mlx5e
master Ethernet netdev/IPoIB parent netdev and mlx5_ib in the near future.
Add the support for attaching multiple underlay QPs for the different Pkeys
in mlx5 core RX steering.
Add Pkey index to rdma_netdev to add the ability to set PKEY index to lower
IPoIB offload netdev.
Use hash-table to map between DQPN (Destination QP number) to child netdev
for the IPoIB parent netdev to forward RX packets to the corresponding
child Pkey netdev, since the RX rings are shared.
The reset of the series adds the ipoib child Pkey: mlx5e netdev profile,
netdev nods implementation and minimal set of ethtool callbacks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-10-13
This series contains updates to mqprio and i40e.
Amritha introduces a new hardware offload mode in tc/mqprio where the TCs,
the queue configurations and bandwidth rate limits are offloaded to the
hardware. The existing mqprio framework is extended to configure the queue
counts and layout and also added support for rate limiting. This is
achieved through new netlink attributes for the 'mode' option which takes
values such as 'dcb' (default) and 'channel' and a 'shaper' option for
QoS attributes such as bandwidth rate limits in hw mode 1. Legacy devices
can fall back to the existing setup supporting hw mode 1 without these
additional options where only the TCs are offloaded and then the 'mode'
and 'shaper' options defaults to DCB support. The i40e driver enables the
new mqprio hardware offload mechanism factoring the TCs, queue
configuration and bandwidth rates by creating HW channel VSIs.
In this new mode, the priority to traffic class mapping and the user
specified queue ranges are used to configure the traffic class when the
'mode' option is set to 'channel'. This is achieved by creating HW
channels(VSI). A new channel is created for each of the traffic class
configuration offloaded via mqprio framework except for the first TC (TC0)
which is for the main VSI. TC0 for the main VSI is also reconfigured as
per user provided queue parameters. Finally, bandwidth rate limits are set
on these traffic classes through the shaper attribute by sending these
rates in addition to the number of TCs and the queue configurations.
Colin Ian King makes an array of constant values "constant".
Alan fixes and issue where on some firmware versions, we were failing to
actually fill out the phy_types which caused ethtool to not report any
link types. Also hardened against a potentially malicious VF by not
letting the VF to reset itself after requesting to change the number of
queues (via ethtool), let the PF reset the VF to institute the requested
changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the pkt_type to PACKET_HOST only if the destination MAC
address matches on the on the source based macvlan. It didn't make sense to
be updating broadcast, multicast, and non-local destined frames with
PACKET_HOST.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch intoduces a slight adjustment for macvlan to address the fact
that in source mode I was seeing two copies of any packet addressed to the
macvlan interface being delivered where there should have been only one.
The issue appears to be that one copy was delivered based on the source MAC
address and then the second copy was being delivered based on the
destination MAC address. To fix it I am just treating a unicast address
match as though it is not a match since source based macvlan isn't supposed
to be matching based on the destination MAC anyway.
Fixes: 79cf79abce ("macvlan: add source mode")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tx_table is part of the private data of kernel net_device. It is only
zero-ed out when allocating net_device.
We may recreate netvsc_device w/o recreating net_device, so the private
netdev data, including tx_table, are not zeroed. It may contain channel
numbers for the older netvsc_device.
This patch adds initialization of tx_table each time we recreate
netvsc_device.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename this variable because it is the Receive indirection
table.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The break statement for the Macronix case is missing and will
fall through to the Winbond case and re-assign the size setting.
Fix this by adding the missing break statement. Also correctly
indent the return statements.
Detected by CoverityScan, CID#1458020 ("Missing break in switch")
Fixes: 96ac18f14a ("cxgb4: Add support for new flash parts")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Collect SGE, PCIE, PM, UP CIM, MA and HMA dumps.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Try to access TP indirect registers via firmware first. If this fails,
fallback and access them directly. This ensures that driver and
firmware do not conflict each other while accessing the TP indirect
registers.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Collect firmware mbox and device logs before collecting the rest of
the hardware dumps to snap the firmware state before the mailbox logs
are updated by other hardware dumps.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Collect EDC0 and EDC1 memory dump.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add base to collect dump entities. Collect register dump and
update template header accordingly.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement operations to set/get dump data via ethtool. Also add
template header that precedes dump data, which helps in decoding
and extracting the dump data.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today's -next build encountered an error due to a missing definition of
WARN_ON(), caused by some header reorganization removing an implicit
inclusion of linux/bug.h. Fix this with an explicit inclusion.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .set_addr function does nothing, remove the dsa_loop implementation
before getting rid of it completely in DSA.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As for mv88e6xxx, setup the switch from within the mv88e6060 driver with
a random MAC address, and remove the .set_addr implementation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E6060 Ethernet switch always transmits the multicast bit of the
switch MAC address as a zero. It re-uses the corresponding bit 8 of the
register "Switch MAC Address Register Bytes 0 & 1" for "DiffAddr".
If the "DiffAddr" bit is 0, then all ports transmit the same source
address. If it is set to 1, then bit 2:0 are used for the port number.
The mv88e6060 driver is currently wrongly shifting the MAC address byte
0 by 9. To fix this, shift it by 8 as usual and clear its bit 0.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An Ethernet switch may support having a MAC address, which can be used
as the switch's source address in transmitted full-duplex Pause frames.
If a DSA switch supports the related .set_addr operation, the DSA core
sets the master's MAC address on the switch. This won't make sense
anymore in a multi-CPU ports system, because there won't be a unique
master device assigned to a switch tree.
Instead, setup the switch from within the Marvell driver with a random
MAC address, and remove the .set_addr implementation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resources such as FT, QPN HT and mdev resources should be allocated
only by parent netdev. Shared resources are allocated and freed by the
parent interface since the parent is always present and created
before the IPoIB PKEY sub-interface.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Similar to VLAN interfaces child interfaces have limited ethtool
support. In current code the main limitation that does not
allow child interface ethtool configuration is due to shared
resources which are managed by the parent.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Child interface ndos will be called to support child interface
specific behaviour.
ndo_init flow:
-Acquire shared QPN to net-device HT from parent
-Continue with the same flow as parent interface
ndo_open flow:
-Initialize child underlay QP and connect to shared FT
-Create child send TIS
-Open child send channels
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Child interface profile will be called to support child interface
specific behaviour. The child code is sparse compared to the parent
since the RX channels are shared between the interfaces.
Creating a septate profile for child and parent will make a smother
code with a better ability for future expansion.
The profile stuct is exposed to the parent using a getter function.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
This change is needed for PKEY support, since the RQs are shared
between the child interface and the parent. The parent is responsible
for NAPI and the precessing of RX completions. Using the dqpn in the
completion descriptor we set the corresponding child IPoIB netdevice
on the SKB.
The mapping between the dqpn and the netdevice is done using a HT,
each mlx5 IPoIB interface registers its mapping on creation.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Added a function to set PKEY index to IPoIB device driver using the
already present set_id function. PKEY index is attached to the QP
during state modification.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
To support passing child interfaces to the lower device a new
rdma_netdev function was used, set_id. This will allow us to
attach the PKEY index lower device resources such as TIS/QP.
For devices that do not support offloads in IPoIB same logic
will be used, setting the PKEY index to priv struct.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
When ndo_open and ndo_stop are called RTNL lock should be held.
In this specific case ipoib_ib_dev_open calls the offloaded ndo_open
which re-sets the number of TX queue assuming RTNL lock is held.
Since RTNL lock is not held, RTNL assert will fail.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Previous support allowed connecting only a single QPN to the FT.
Now using a linked list multiple QPNs can be attached to the same FT.
Supporting attaching multiple underlay QPs is required for PKEY
support in which child and parent share the same FT.
The actual attaching/detaching FW commands will be called inside the
function symmetrically.
This change requires a change in IPoIB open and close functions, the
attaching/detaching to/from the FT is done each time we open/close.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
During the creation of the underlay QP the PKEY index is unknown, the
PKEY index is known only when calling ndo_open.
PKEY index attached to the QP during state modification.
Splitting the functions will also make the code symmetric and more
readable. This split is also required for later PKEY support to be
called with the PKEY index during ndo_open.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>