After VRR Push is sent, need to wait till flipline decision boundary
to get Push bit to get cleared.
--v2:
- Adjust delays to vrr vmin vblank delays. (Ankit)
--v3:
- Change intel_vrr_vmin_safe_window_end() so that
intel_dsb_wait_for_delayed_vblank() uses correct delay. (Ankit)
--v4:
- Simplify intel_vrr_vmin_safe_window_end implementation. (Ankit)
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20251223104542.2688548-15-mitulkumar.ajitkumar.golani@intel.com
Add vblank evasion logic when vrr is already enabled along with
dc balance is computed.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20251223104542.2688548-14-mitulkumar.ajitkumar.golani@intel.com
Write DC Balance parameters to hw registers.
--v2:
- Update commit header.
- Separate crtc_state params from this patch. (Ankit)
--v3:
- Write registers at compute config.
- Update condition for write.
--v4:
- Address issue with state checker.
--v5:
- Initialise some more dc balance register while enabling VRR.
--v6:
- FLIPLINE_CFG need to be configure at last, as it is double buffer
arming point.
--v7:
- Initialise and reset live value of vmax and vmin as well.
--v8:
- Add separate functions while writing hw registers. (Ankit)
--v9:
- Add DC Balance counter enable bit to this patch. (Ankit)
--v10:
- Add rigister writes to vrr_enable/disable. (Ankit)
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20251223104542.2688548-12-mitulkumar.ajitkumar.golani@intel.com
Track dc balance flip count with params per crtc. Increment
DC Balance Flip count before every flip to indicate DMC
firmware about new flip occurrence which needs to be adjusted
for dc balancing. This is tracked separately from legacy
FLIP_COUNT register also Reset DC balance flip count value
while disabling VRR adaptive mode, this is to start with
fresh counts when VRR adaptive refresh mode is triggered again.
--v2:
- Call during intel_update_crtc.(Ankit)
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20251223104542.2688548-11-mitulkumar.ajitkumar.golani@intel.com
Add function which resets all accumulated DC Balance parameters
whenever adaptive mode of VRR goes off. This helps to give a
fresh start when VRR is re-enabled.
--v2:
- Typo, change crtc_state to old_crtc_state. (Ankit)
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20251223104542.2688548-10-mitulkumar.ajitkumar.golani@intel.com
Add a function that checks if DC Balance enabling is possible on the
requested PIPE. Apart from the DISPLAY_VER check, account for current
firmware limitations, which only allow DC Balance on PIPE A and PIPE B.
v2: Rephrased commit message. (Ankit)
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20251223104542.2688548-9-mitulkumar.ajitkumar.golani@intel.com
Compute DC Balance parameters and tunable params based on
experiments.
--v2:
- Document tunable params. (Ankit)
--v3:
- Add line spaces to compute config. (Ankit)
- Remove redundancy checks.
--v4:
- Separate out conpute config to separate function.
- As all the valuse are being computed in scanlines, and slope
is still in usec, convert and store it to scanlines.
--v5:
- Update and add comments for slope calculation. (Ankit)
- Update early return conditions for dc balance compute. (Ankit)
--v6:
- Early return condition simplified for dc balance compute config. (Ankit)
- Make use of pipe restrictions to this patch. (Ankit)
--v7:
- Separate out PIPE_A and PIPE_B restrictions to other patch.(Ankit)
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20251223104542.2688548-8-mitulkumar.ajitkumar.golani@intel.com
Add DC Balance params to crtc_state, also add state checker
params for related properties.
--v3:
- Seggregate crtc_state params with this patch. (Ankit)
--v4:
- Update commit message and header. (Ankit)
- Add +1 to VMIN and VMAX only when it is non-zero. (Ankit)
--v5:
- Add headers in sorted order. (Jani Nikula)
--v6:
- Add a separate function to get and check dc_balance params.
- Avoid repeatative use of MMIO read. (Ankit)
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20251223104542.2688548-6-mitulkumar.ajitkumar.golani@intel.com
Calculate delayed vblank start position with the help of added
vmin/vmax stuff for next frame and final computation.
--v2:
- Correct Author details.
--v3:
- Separate register details from this patch.
--v4:
- Add mask macros.
--v5:
- As live prefix params indicate timings for current frame,
read just _live prefix values instead of next frame timings as
done previously.
- Squash Refactor vrr params patch.
--v6:
- Use error code while returning invalid values. (Jani, Nikula)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20251223104542.2688548-5-mitulkumar.ajitkumar.golani@intel.com
Add VRR register offsets and bits to access DC Balance configuration.
--v2:
- Separate register definitions. (Ankit)
- Remove usage of dev_priv. (Jani, Nikula)
--v3:
- Convert register address offset, from capital to small. (Ankit)
- Move mask bits near to register offsets. (Ankit)
--v4:
- Use _MMIO_TRANS wherever possible. (Jani)
--v5:
- Added LIVE Value registers for VMAX and FLIPLINE as provided by DMC fw
- For pipe B it is temporary and expected to change later once finalised.
--v6:
- Add live value registers for DCB VMAX/FLIPLINE.
--v7:
- Correct commit message file. (Jani Nikula)
- Add bits in highest to lowest order. (Jani Nikula)
--v8:
- Register/bitfields indentation changes as per i915_reg.h
mentioned format (Jani, Ankit)
--v9:
- Remove comment. (Ankit)
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20251223104542.2688548-4-mitulkumar.ajitkumar.golani@intel.com
Add support for the optional LIS2MDL magnetometer on GW71xx baseboards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As per datasheet of the HDMI protection IC the CEC_IC pin has been
configured as open-drain.
Fixes: ddabb3ce3f ("arm64: dts: freescale: add TQMa8MPQL on MBa8MP-RAS314")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The event out signal on channel 2 is available on pad SAI2_RXD0 which is
connected to X63 pin 13.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As per datasheet of the HDMI protection IC the CEC_IC pin has been
configured as open-drain.
Fixes: 418d1d840e ("arm64: dts: freescale: add initial device tree for TQMa8MPQL with i.MX8MP")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Replace personal mail address by mailing list.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the hdmi_pai device on the Toradex SMARC iMX8M Plus Development
boards.
The hdmi_pai device, together with aud2htx module, hdmi_pai and hdmi
controller compose the HDMI audio pipeline.
See commit b21f87b832 ("arm64: dts: imx8mp-evk: enable hdmi_pai
device") for the equivalent change on the NXP i.MX8MP EVK board.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the hdmi_pai device on the various iMX8M Plus Verdin boards that
feature the related HDMI interface.
The hdmi_pai device, together with aud2htx module, hdmi_pai and hdmi
controller compose the HDMI audio pipeline.
See commit b21f87b832 ("arm64: dts: imx8mp-evk: enable hdmi_pai
device") for the equivalent change on the NXP i.MX8MP EVK board.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove obsolete TODO comments, I2S interface is supported since Linux v6.6.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add alias for the apalis first ethernet interface, this ensures
consistent interface naming (e.g. `end0`) and this is used by the
firmware to correctly set the MAC address.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the LPSPI6 controller so it can be used by user applications
through the board’s expansion connector.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Symphony carrier board includes a USB Type-C connector on the USB1
port through an NXP PTN5150 Type-C controller connected on the I2C bus.
The PTN5150 provides cable orientation detection and role switching
information to the USB controller.
This patch adds the PTN5150 node, its interrupt line, the required pin
muxing, and wires the controller to the USB1 OTG dual-role device using
the USB role-switch framework.
This patch adds also USB2 support, that remains in host-only mode,
matching the hardware capabilities of the Symphony board.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Symphony carrier board exposes a capacitive touch interface through an
FFC/FPC connector. This interface is wired to an FT5x06 touch controller
on the I2C bus when using Variscite’s 7-inch capacitive touch display.
This patch adds the FT5x06 device node to describe the actual hardware
connection and enables touch functionality on the Symphony board
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch introduces 2 simple aliases:
Add a gpio3->gpio4 alias to allow flexible access to these GPIOs
Add a gpio4 alias for the PCA9534 GPIO expander.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i2c3 of the phyBOARD-Pollux is used on the CSI1 interface to connect
to imaging sensors. Thus define it so it can be easily enabled if
required.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The spi flash on the SoM is missing its vcc supply definition. Add
missing regulator which supplies the flash with 1.8V.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add 5v regulator to gpio fan node.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PDM micphone sound card support.
This sound card supports recording sound from PDM microphone
and convert the PDM format data to PCM data.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add WM8962 sound card support which connects to SAI3.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add bt-sco sound card, which is used by BT HFP case.
It supports wb profile as default.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Refine label with "wm8962" and node name with "codec" to follow
devicetree specification.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The commit 616effc027 ("arm64: dts: imx8: Fix lpuart DMA channel
order") swap uart rx and tx channel at common imx8-ss-dma.dtsi. But miss
update imx8qm-ss-dma.dtsi.
The commit 5a8e9b022e ("arm64: dts: imx8qm-ss-dma: Pass lpuart
dma-names") just simple add dma-names as binding doc requirement.
Correct lpuart0 - lpuart3 dma rx and tx channels, and use defines for
the FSL_EDMA_RX flag.
Fixes: 5a8e9b022e ("arm64: dts: imx8qm-ss-dma: Pass lpuart dma-names")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing 'clocks' property to LAN8740Ai PHY node, to allow the PHY driver
to manage LAN8740Ai CLKIN reference clock supply. This fixes sporadic link
bouncing caused by interruptions on the PHY reference clock, by letting the
PHY driver manage the reference clock and assure there are no interruptions.
This follows the matching PHY driver recommendation described in commit
bedd8d78ab ("net: phy: smsc: LAN8710/20: add phy refclk in support")
Fixes: 8d6712695b ("arm64: dts: imx8mp: Add support for DH electronics i.MX8M Plus DHCOM and PDK2")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
CAN1 and Micfil share pins on imx93-9x9-qsb board, use TMUX1574RSVR
to control the connection: put sel to high, select CAN1, put sel to
low, select Micfil. In default, sel keep low.
To support CAN1, need to put the sel to high. Besides, CAN1 use phy
TJA1057GT/3.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On this SoM eqos is the primary ethernet interface, Ka-Ro fuses the
address for it in eth_mac1, eth_mac2 seems to be left unfused. In their
downstream u-boot they fetch it from eth_mac1 [1][2], by setting alias
of eqos to ethernet0, the driver then fetches the mac address based on
the alias number.
Set eqos to read from eth_mac1 instead of eth_mac2. Also set fec to
point at eth_mac2 as it may be fused later even though it is disabled
by default.
With this changed barebox is now capable of loading the correct address.
Link: 3805432784/drivers/net/dwc_eth_qos.c (L1167) [1]
Link: 3805432784/arch/arm/dts/imx8mp-karo.dtsi (L12) [2]
Fixes: bac63d7c5f ("arm64: dts: freescale: add Ka-Ro Electronics tx8p-ml81 COM")
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The compatibles should include the SoM compatible, this board is based
on the Ka-Ro TX8P-ML81 SoM, so add it to allow using shared code in the
bootloader which uses upstream Linux devicetrees as a base.
Also add the hardware revision to the board compatible to handle
revision specific quirks in the bootloader/userspace.
This is a breaking change, but it is early enough that it can be
corrected without causing any issues.
Fixes: 03f07be54c ("arm64: dts: freescale: Add the GOcontroll Moduline Display baseboard")
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The compatibles should include the SoM compatible, this board is based
on the Ka-Ro TX8P-ML81 SoM, so add it to allow using shared code in the
bootloader which uses upstream Linux devicetrees as a base.
Also add the hardware revision to the board compatible to handle
revision specific quirks in the bootloader/userspace.
This is a breaking change, but it is early enough that it can be
corrected without causing any issues.
Fixes: 24e67d28ef ("dt-bindings: arm: fsl: Add GOcontroll Moduline Display")
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RTC interrupt level should be set to "LOW". This was revealed by the
introduction of commit:
f181987ef4 ("rtc: m41t80: use IRQ flags obtained from fwnode")
which changed the way IRQ type is obtained.
Fixes: 56c27310c1 ("ARM: dts: imx: Add Advantech BA-16 Qseven module")
Signed-off-by: Ian Ray <ian.ray@gehealthcare.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DRAM1 is only 2GiB in size (0x00_8000_0000 - 0x01_0000_0000) which is
already used by Linux kernel, etc. Move the allocation area of BMAN and
QMAN to DRAM1 region. This frees the complete DRAM2 area for e.g. CMA.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When ksmbd_vfs_getattr() fails, the reference count of ksmbd_file
must be released.
Suggested-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: ZhangGuoDong <zhangguodong@kylinos.cn>
Signed-off-by: ChenXiaoSong <chenxiaosong@kylinos.cn>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
