This enables QoS configuration for QNOC type device which can be found
on SA8775P platform. It enables QoS configuration for master ports with
predefined priority and urgency forwarding. This helps in prioritizing
the traffic originating from different interconnect masters at NOC.
The system may function normally without this feature. However, enabling
QoS helps optimize latency and bandwidth across subsystems like CPU, GPU,
and multimedia engines, which becomes important in high-throughput
scenarios. This is a feature aimed at performance enhancement to improve
system performance under concurrent workloads.
* icc-sa8775p
dt-bindings: interconnect: add reg and clocks properties to enable QoS on sa8775p
interconnect: qcom: sa8775p: enable QoS configuration
Link: https://lore.kernel.org/r/20251001073344.6599-1-odelu.kukatla@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Drop the QPIC interconnect and BCM nodes for the SDX75 SoC. The reason
is that this QPIC BCM resource is already defined as a RPMh clock in
clk-rpmh driver as like other SDX SoCs. So it is wrong to describe the
same resource in two different providers.
Also, without this series, the NAND driver fails to probe on SDX75 as
the interconnect sync state disables the QPIC nodes as there were no
clients voting for this ICC resource. However, the NAND driver had already
voted for this BCM resource through the clk-rpmh driver. Since both votes
come from Linux, RPMh was unable to distinguish between these two and ends
up disabling the resource during sync state.
* icc-sdx75
interconnect: qcom: sdx75: Drop QPIC interconnect and BCM nodes
dt-bindings: interconnect: qcom: Drop QPIC_CORE IDs
Link: https://lore.kernel.org/r/20250926-sdx75-icc-v2-0-20d6820e455c@oss.qualcomm.com>
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The lack of the interconnects for the USB2 host might result in the
register writes for the PHY not reaching the PHY and thus the PLL not
locking up, resulting in -EBUSY errors for the USB host on the platform.
Add missing interconnect link and add interconnect paths to the USB2
device.
* icc-msm8996
interconnect: qcom: msm8996: add missing link to SLAVE_USB_HS
arm64: dts: qcom: msm8996: add interconnect paths to USB2 controller
Link: https://lore.kernel.org/r/20251002-fix-msm8996-icc-v1-0-a36a05d1f869@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
-----BEGIN PGP SIGNATURE-----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=woNE
-----END PGP SIGNATURE-----
Merge tag 'nf-next-25-10-30' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next
Florian Westphal says:
====================
netfilter: updates for net-next
1) Convert nf_tables 'nft_set_iter' usage to use C99 struct
initialization, from Fernando Fernandez Mancera.
2) Disallow nf_conntrack_max=0. This was an (undocumented)
historic inheritance from ip_conntrack (ipv4 only nf_conntrack
predecessor). Doing so will simplify future changes to make
this pernet-tuneable.
3) Fix a typo in conntrack.h comment, from Weibiao Tu.
* tag 'nf-next-25-10-30' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: fix typo in nf_conntrack_l4proto.h comment
netfilter: conntrack: disable 0 value for conntrack_max setting
netfilter: nf_tables: use C99 struct initializer for nft_set_iter
====================
Link: https://patch.msgid.link/20251030121954.29175-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The icc_commit_set() function, used by the debugfs interface, checks
the validity of the global cur_path pointer using IS_ERR_OR_NULL().
However, in the specific case where cur_path is NULL, while
IS_ERR_OR_NULL(NULL) correctly evaluates to true, the subsequent call
to PTR_ERR(NULL) returns 0.
This causes the function to return a success code (0) instead of an
error, misleading the user into believing their bandwidth request was
successfully committed when, in fact, no operation was performed.
Fix this by adding an explicit check to return -EINVAL if cur_path is
NULL. This prevents silent failures and ensures that an invalid
operational sequence is immediately and clearly reported as an error.
Fixes: 770c69f037 ("interconnect: Add debugfs test client")
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Link: https://lore.kernel.org/r/20251010151447.2289779-1-visitorckw@gmail.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
As like other SDX targets, SDX75 QPIC BCM resource is also modeled as a
RPMh clock in clk-rpmh driver. However, for SDX75, this resource was also
described as an interconnect node mistakenly.
Hence, drop the QPIC interconnect IDs and let the clients use clk-rpmh
driver to vote for this resource.
Even though this change is an ABI break, it is necessary to avoid
describing the same resource provider in two different drivers, as it may
lead to votes from clients overriding each other.
Fixes: 956329ec7c ("dt-bindings: interconnect: Add compatibles for SDX75")
Signed-off-by: Raviteja Laggyshetty <quic_rlaggysh@quicinc.com>
[mani: kept the QUP defines value unchanged]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250926-sdx75-icc-v2-2-20d6820e455c@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
As like other SDX SoCs, SDX75 SoC's QPIC BCM resource was modeled as a
RPMh clock in clk-rpmh driver. However, for SDX75, this resource was also
described as an interconnect and BCM node mistakenly. It is incorrect to
describe the same resource in two different providers, as it will lead to
votes from clients overriding each other.
Hence, drop the QPIC interconnect and BCM nodes and let the clients use
clk-rpmh driver to vote for this resource.
Without this change, the NAND driver fails to probe on SDX75, as the
interconnect sync state disables the QPIC nodes as there were no clients
voting for this ICC resource. However, the NAND driver had already voted
for this BCM resource through the clk-rpmh driver. Since both votes come
from Linux, RPMh was unable to distinguish between these two and ends up
disabling the QPIC resource during sync state.
Cc: stable@vger.kernel.org
Fixes: 3642b4e5cb ("interconnect: qcom: Add SDX75 interconnect provider driver")
Signed-off-by: Raviteja Laggyshetty <quic_rlaggysh@quicinc.com>
[mani: dropped the reference to bcm_qp0, reworded description]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Lakshmi Sowjanya D <quic_laksd@quicinc.com> # on SDX75
Link: https://lore.kernel.org/r/20250926-sdx75-icc-v2-1-20d6820e455c@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
When a command times out, mark it as ERT_CMD_STATE_TIMEOUT. Any other
commands that are canceled due to this timeout should be marked as
ERT_CMD_STATE_ABORT.
Fixes: aac243092b ("accel/amdxdna: Add command execution")
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://patch.msgid.link/20251029193423.2430463-1-lizhi.hou@amd.com
Add 'reg' and 'clocks' properties to enable QoS configuration. These
properties enable access to QoS registers and necessary clocks for
configuration.
QoS configuration is essential for ensuring that latency sensitive
components such as CPUs and multimedia engines receive prioritized
access to memory and interconnect resources. This helps to manage
bandwidth and latency across subsystems, improving system responsiveness
and performance in concurrent workloads.
Both 'reg' and 'clocks' properties are optional. If either is missing,
QoS configuration will be skipped. This behavior is controlled by the
'qos_requires_clocks' flag in the driver, which ensures that QoS
configuration is bypassed when required clocks are not defined.
Signed-off-by: Odelu Kukatla <odelu.kukatla@oss.qualcomm.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20251001073344.6599-2-odelu.kukatla@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
We are trying to move away from netdevsim-only tests and towards
tests which can be run both against netdevsim and real drivers.
Replace the simple bash script we have for checking ethtool -g/-G
on netdevsim with a Python test tweaking those params as well
as channel count.
The new test is not exactly equivalent to the netdevsim one,
but real drivers don't often support random ring sizes,
let alone modifying max values via debugfs.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251029164930.2923448-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-10-29 (ice, i40e, idpf, ixgbe, igbvf)
For ice:
Michal converts driver to utilize Page Pool and libeth APIs. Conversion
is based on similar changes done for iavf in order to simplify buffer
management, improve maintainability, and increase code reuse across
Intel Ethernet drivers.
Additional details:
https://lore.kernel.org/20250925092253.1306476-1-michal.kubiak@intel.com
Alexander adds support for header split, configurable via ethtool.
Grzegorz allows for use of 100Mbps on E825C SGMII devices.
For i40e:
Jay Vosburgh avoids sending link state changes to VF if it is already in
the requested state.
For idpf:
Sreedevi removes duplicated defines.
For ixgbe:
Alok Tiwari fixes some typos.
For igbvf:
Alok Tiwari fixes output of VLAN warning message.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igbvf: fix misplaced newline in VLAN add warning message
ixgbe: fix typos in ixgbe driver comments
idpf: remove duplicate defines in IDPF_CAP_RSS
i40e: avoid redundant VF link state updates
ice: Allow 100M speed for E825C SGMII device
ice: implement configurable header split for regular Rx
ice: switch to Page Pool
ice: drop page splitting and recycling
ice: remove legacy Rx and construct SKB
====================
Link: https://patch.msgid.link/20251029231218.1277233-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the missing interconnects to the USB2 host. The Fixes tag points to
the commit which broke probing of the USB host on that platform.
Fixes: 130733a100 ("interconnect: qcom: msm8996: Promote to core_initcall")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20251002-fix-msm8996-icc-v1-2-a36a05d1f869@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
>From the initial submission the interconnect driver missed the link from
SNOC_PNOC to the USB 2 configuration space. Add missing link in order to
let the platform configure and utilize this path.
Fixes: 7add937f52 ("interconnect: qcom: Add MSM8996 interconnect provider driver")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251002-fix-msm8996-icc-v1-1-a36a05d1f869@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The mixed SQE support assumes that userspace always passes valid data,
that is not the case. Validate the opcode properly before indexing
the io_issue_defs[] array, and pass it through the nospec indexing
as well as it's a user valid indexing a kernel array.
Fixes: 1cba30bf9f ("io_uring: add support for IORING_SETUP_SQE_MIXED")
Reported-by: syzbot+b883b008a0b1067d5833@syzkaller.appspotmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Initialize the bmi_target_info structure using = {} at declaration time
instead of calling memset() in each bus-specific code path. This
simplifies the code and avoids an explicit memset.
Signed-off-by: Zhongqiu Han <zhongqiu.han@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251030130023.1836808-3-zhongqiu.han@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Initialize the pm_qos_request structure using = {} instead of memset() in
ath10k_download_fw(). This ensures the structure is properly zeroed before
passing it to cpu_latency_qos_add_request(), and improves efficiency by
avoiding an explicit runtime memset.
Signed-off-by: Zhongqiu Han <zhongqiu.han@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251030130023.1836808-2-zhongqiu.han@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During scan and remain-on-channel requests, a scan link vif (arvif) is
assigned and a temporary vdev is created. If vdev creation fails, the
assigned arvif is left attached until the virtual interface is removed,
leaving a stale link in ahvif.
Fix this by freeing the stale arvif and resetting the corresponding link in
ahvif by calling ath12k_mac_unassign_link_vif() when vdev creation fails.
While at it, propagate the actual error code from ath12k_mac_vdev_create()
instead of returning -EINVAL in ath12k_mac_initiate_hw_scan().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: 477cabfdb7 ("wifi: ath12k: modify link arvif creation and removal for MLO")
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251026182254.1399650-3-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, vdev limit check is performed only in
ath12k_mac_assign_vif_to_vdev(). If the host has already created
maximum number of vdevs for the radio (ar) and a scan request
arrives for the same radio, ath12k_mac_initiate_hw_scan() attempts
to create a vdev without checking the limit, causing firmware asserts.
Centralize the vdev limit guard by moving the check into
ath12k_mac_vdev_create() so that all callers obey the limit.
While doing this, update the condition from
`num_created_vdevs > (TARGET_NUM_VDEVS(ab) - 1)` to
`num_created_vdevs >= TARGET_NUM_VDEVS(ab)` for clarity and to
eliminate unnecessary arithmetic.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: 0d6e6736ed ("wifi: ath12k: scan statemachine changes for single wiphy")
Fixes: 4938ba733e ("wifi: ath12k: modify remain on channel for single wiphy")
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251026182254.1399650-2-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Fixed rate is set for STAs that are associated. This will be done
during association or with ath12k_sta_rc_update_wk().
Add EHT fixed rate setting for STAs by adding call to
ath12k_mac_set_peer_eht_fixed_rate() during the times fixed rate is
set for STAs. This new function sets EHT fixed rate for a peer, which
sends WMI command with the updated MCS/NSS rate using
WMI_PEER_PARAM_FIXED_RATE command id.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Co-developed-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251024001928.257356-7-muna.sinada@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add EHT MCS/NSS rate functionality to peer association. As part of
ath12k_peer_assoc_h_eht() add the calculation of EHT MCS/NSS using
intersection of link_sta and phy capability.
ath12k_mac_max_eht_mcs_nss() function is utilized when comparing the
max NSS of link STA and phy capability since in split phy case, phy
supports max NSS of 2 for 5G band.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Co-developed-by: Vishal Kumar <quic_visk@quicinc.com>
Signed-off-by: Vishal Kumar <quic_visk@quicinc.com>
Co-developed-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251024001928.257356-4-muna.sinada@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add EHT rate handling to the existing rate functions that validate,
prepare and set rates.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Co-developed-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251024001928.257356-3-muna.sinada@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, functions in mac.c for setting GI and LTF rates are
specifically for HE rates.
Remove any mention of "HE" in such functions in order to allow for
other modes to utilize the functions. The intention is to prepare for
the addition of EHT GI and LTF fixed rate settings.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251024001928.257356-2-muna.sinada@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In ath12k_core_init() when ath12k_core_hw_group_create() fails,
ath12k_core_hw_group_destroy() is called where for each device below
path would get executed
ath12k_core_soc_destroy()
ath12k_qmi_deinit_service()
qmi_handle_release()
This results in kernel crash in case one of the device fails at
qmi_handle_init() when creating hardware group:
ath12k_pci 0000:10:00.0: failed to initialize qmi handle
ath12k_pci 0000:10:00.0: failed to initialize qmi :-517
ath12k_pci 0000:10:00.0: failed to create soc core: -517
ath12k_pci 0000:10:00.0: unable to create hw group
BUG: unable to handle page fault for address: ffffffffffffffb7
RIP: 0010:qmi_handle_release
Call Trace:
<TASK>
ath12k_qmi_deinit_service
ath12k_core_hw_group_destroy
ath12k_core_init
ath12k_pci_probe
The detailed reason is, when qmi_handle_init() fails for a device
ab->qmi.handle is not correctly initialized. Then
ath12k_core_hw_group_create() returns failure, since error handing
is done for all device, eventually qmi_handle_release() is called for the
issue device and finally kernel crashes due to the uninitialized
ab->qmi.handle.
Fix this by moving error handling to ath12k_core_hw_group_create(), this
way the issue device can be skipped.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 6f245ea0ec ("wifi: ath12k: introduce device group abstraction")
Link: https://lore.kernel.org/ath12k/fabc97122016d1a66a53ddedd965d134@posteo.net
Reported-by: a-development <a-development@posteo.de>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220518
Tested-by: a-development <a-development@posteo.de>
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251030-fix-hw-group-create-err-handling-v1-1-0659e4d15fb9@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During firmware recovery or suspend/resume, m3 memory could be reused if
the size of the new m3 binary is equal to or less than that of the
existing memory. There will be issues for the latter case, since
m3_mem->size will be updated with a smaller value and this value is
eventually used in the free path, where the original total size should be
used instead.
To fix it, add a new member in m3_mem_region structure to track the original
memory size and use it in free path.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Fixes: 05090ae82f ("wifi: ath12k: check M3 buffer size as well whey trying to reuse it")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251029-ath12k-fix-m3-reuse-v1-1-69225bacfc5d@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When the call to ath12k_wmi_arp_ns_offload() fails, the temporary memory
allocation for offload is not freed before returning. Fix that by
freeing offload in the error path.
Fixes: 1666108c74 ("wifi: ath12k: support ARP and NS offload")
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20251028170457.134608-1-nihaal@cse.iitm.ac.in
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add VGIC maintenance interrupt and interrupt-parent property for
interrupt controller, required to run Linux in virtualized environment.
Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
nand-controller@ffb90000 (altr,socfpga-denali-nand): Unevaluated
properties are not allowed ('flash@0' was unexpected)
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Unevaluated properties are not allowed ('phy-addr' was unexpected)
socfpga_stratix10_swvp.dtb: sysmgr@ffd12000 (altr,sys-mgr-s10):
'interrupts' does not match any of the regexes:
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The python version of the kernel-doc parser emits some strange warnings
with just a line number in certain cases:
$ ./scripts/kernel-doc -Wall -none 'include/linux/virtio_config.h'
Warning: 174
Warning: 184
Warning: 190
Warning: include/linux/virtio_config.h:226 No description found for return value of '__virtio_test_bit'
Warning: include/linux/virtio_config.h:259 No description found for return value of 'virtio_has_feature'
Warning: include/linux/virtio_config.h:283 No description found for return value of 'virtio_has_dma_quirk'
Warning: include/linux/virtio_config.h:392 No description found for return value of 'virtqueue_set_affinity'
I eventually tracked this down to the lone call of emit_msg() in the
KernelEntry class, which looks like:
self.emit_msg(self.new_start_line, f"duplicate section name '{name}'\n")
This looks like all the other emit_msg calls. Unfortunately, the definition
within the KernelEntry class takes only a message parameter and not a line
number. The intended message is passed as the warning!
Pass the filename to the KernelEntry class, and use this to build the log
message in the same way as the KernelDoc class does.
To avoid future errors, mark the warning parameter for both emit_msg
definitions as a keyword-only argument. This will prevent accidentally
passing a string as the warning parameter in the future.
Also fix the call in dump_section to avoid an unnecessary additional
newline.
Fixes: e3b42e94cf ("scripts/lib/kdoc/kdoc_parser.py: move kernel entry to a class")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Message-ID: <20251030-jk-fix-kernel-doc-duplicate-return-warning-v2-1-ec4b5c662881@intel.com>
Rename drm_client_framebuffer_flush() to drm_cient_buffer_flush() and
adapt its callers. The old name was left over from previous naming
conventions.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>>
Tested-by: Francesco Valla <francesco@valla.it>
Link: https://patch.msgid.link/20251027121042.143588-8-tzimmermann@suse.de
Rename drm_client_framebuffer_create() to drm_client_buffer_create_dump()
and adapt callers. The new name reflects the function's purpose. Using
dumb buffers is the easiest way for creating a GEM buffer in a drivers-
independent way.
There's also drm_client_buffer_create(), which creates the client buffer
from a preexisting buffer object. This helper can be exported for drivers
that create their own GEM buffer object.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Francesco Valla <francesco@valla.it>
Link: https://patch.msgid.link/20251027121042.143588-7-tzimmermann@suse.de
Release client buffers with drm_client_buffer_delete() instead of
drm_client_framebuffer_delete(). The latter is just a tiny wrapper
around the former.
Move the test for !buffer into drm_client_buffer_delete(), although
all callers appear to always have a valid pointer.
v2:
- test for !buffer before deref-ing pointer (Jocelyn, Dan)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Francesco Valla <francesco@valla.it>
Link: https://patch.msgid.link/20251027121042.143588-6-tzimmermann@suse.de
The client buffer's framebuffer holds a reference and pointer on
each of its GEM buffer objects. Thus the field gem in the client-
buffer struct is not necessary. Deprecated the field and convert
the client-buffer helpers to use the framebuffer's objects.
In drm_client_buffer_delete(), do a possible vunmap before releasing
the framebuffer. Otherwise we'd eventually release the framebuffer
before unmaping its buffer objects.
v2:
- avoid dependency on CONFIG_DRM_KMS_HELPER
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Francesco Valla <francesco@valla.it>
Link: https://patch.msgid.link/20251027121042.143588-5-tzimmermann@suse.de
Creating and deleting a client buffer always creates and deletes
the underlying DRM framebuffer. Inline the helper functions into
their callers.
With the _addfb code being inlined into drm_client_buffer_create(),
clean up the function's error rollback to release the framebuffer's
handle and GEM buffer object as needed.
Move the _rmfb code into drm_client_buffer_delete() rather than its
current location in drm_client_framebuffer_delete(). The former is
now the inverse of drm_client_buffer_create(). Makes no difference
for cleaning up. Also prepares for the removal of
drm_client_framebuffer_delete().
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Francesco Valla <francesco@valla.it>
Link: https://patch.msgid.link/20251027121042.143588-4-tzimmermann@suse.de
Dumb-buffer creation within the client code is asymetrically balanced
across drm_client_buffer_create() and drm_client_framebuffer_create().
Put all dumb-buffer code into drm_client_framebuffer_create() and leave
client-buffer initialization to drm_client_buffer_create(). Clarifies
responsibility between these functions.
Apart form the architectural improvements, drm_client_buffer_create()
can now be exported if needed by clients. The client will be able to
initialize buffers that have been created from other interfaces than
dumb buffers.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Francesco Valla <francesco@valla.it>
Link: https://patch.msgid.link/20251027121042.143588-3-tzimmermann@suse.de
Only the client-buffer setup uses the pitch field from struct
drm_client_buffer. Remove the field and pass the value among setup
helpers.
Clients that need the pitch should rather look at the framebuffer's
pitches[0] directly.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Francesco Valla <francesco@valla.it>
Link: https://patch.msgid.link/20251027121042.143588-2-tzimmermann@suse.de
Preserve the I/O register bits in __ast_write8_i_masked() as specified
by preserve_mask. Accidentally OR-ing the output value into these will
overwrite the register's previous settings.
Fixes display output on the AST2300, where the screen can go blank at
boot. The driver's original commit 312fec1405 ("drm: Initial KMS
driver for AST (ASpeed Technologies) 2000 series (v2)") already added
the broken code. Commit 6f719373b9 ("drm/ast: Blank with VGACR17 sync
enable, always clear VGACRB6 sync off") triggered the bug.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reported-by: Peter Schneider <pschneider1968@googlemail.com>
Closes: https://lore.kernel.org/dri-devel/a40caf8e-58ad-4f9c-af7f-54f6f69c29bb@googlemail.com/
Tested-by: Peter Schneider <pschneider1968@googlemail.com>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Fixes: 6f719373b9 ("drm/ast: Blank with VGACR17 sync enable, always clear VGACRB6 sync off")
Fixes: 312fec1405 ("drm: Initial KMS driver for AST (ASpeed Technologies) 2000 series (v2)")
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Nick Bowler <nbowler@draconx.ca>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jocelyn Falempe <jfalempe@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v3.5+
Link: https://patch.msgid.link/20251024073626.129032-1-tzimmermann@suse.de
Merge ACPI button, ACPI backlight (video), and ACPI fan driver fixes for
6.18-rc4:
- Call input_free_device() on failing input device registration as
necessary (and mentioned in the input subsystem documentation) in the
ACPI button driver (Kaushlendra Kumar)
- Fix use-after-free in acpi_video_switch_brightness() by canceling
a delayed work during tear-down (Yuhao Jiang)
- Use platform device for devres-related actions in the ACPI fan driver
to allow device-managed resources to be cleaned up properly (Armin
Wolf)
* acpi-button:
ACPI: button: Call input_free_device() on failing input device registration
* acpi-video:
ACPI: video: Fix use-after-free in acpi_video_switch_brightness()
* acpi-fan:
ACPI: fan: Use platform device for devres-related actions
ACPI: fan: Use ACPI handle when retrieving _FST
This devkit is very similar to P3450, except it has less RAM, no display
port, and only 3 USB host ports. Derive from P3450 and disable the
hardware that is unavailable.
GPIO PA6 is used to control the HDMI power rail and needs to be on for
hotplug detect to work. This is mapped to the 3.3V USB hub on P3450.
That USB rail is not used here, so delete the regulator to avoid
conflicts.
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
- Add the audio devices for the Tegra264 SoC in the tegra264.dtsi file,
which includes sound, HDA and APE(Audio Processing Engine) subsystem
nodes.
APE subsystem includes,
- I/O interfaces such as I2S, DMIC and DSPK (all the available
instances).
- HW accelerators such as ASRC, OPE, MVC, SFC, AMX, ADX and Mixer (all
the available instances).
- ADMA controller and Interrupt controllers.
- Enable the audio nodes in tegra264-p3971.dtsi platform DT file.
Signed-off-by: sheetal <sheetal@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the device tree nodes for the MAIN and AON pin controllers found on
the Tegra186 family of SoCs.
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Merge a cpuidle fix and two fixes related to system sleep for 6.18-rc4:
- Add an exit latency check to the menu cpuidle governor in the case
when it considers using a real idle state instead of a polling one to
address a performance regression (Rafael Wysocki)
- Revert an attempted cleanup of a system suspend code path that
introduced a regression elsewhere (Samuel Wu)
- Allow pm_restrict_gfp_mask() to be called multiple times in a row
and adjust pm_restore_gfp_mask() accordingly to avoid having to play
nasty games with these calls during hibernation (Rafael Wysocki)
* pm-cpuidle:
cpuidle: governors: menu: Select polling state in some more cases
* pm-sleep:
PM: sleep: Allow pm_restrict_gfp_mask() stacking
Revert "PM: sleep: Make pm_wakeup_clear() call more clear"