Some KASAN builds are failing to properly optimize this code --
luckily we don't care about core quality for KASAN builds, so just
exclude it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Closes: https://lore.kernel.org/oe-kbuild-all/202510251641.idrNXhv5-lkp@intel.com/
Add SOC special compatible string, remove fallback snps,dwc3 to let flatten
dwc3-layerscape driver to be probed and enable dma-coherence for usb node
since commit add layerscape dwc3 support, which set correct gsbustcfg0
value.
Add iommus property to run at old uboot, which use fixup add iommus by
check compatible string snsp,dwc3 compatible string.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the performance monitor unit for the Cortex-A55 cores on the
RZ/N2H (R9A09G087) SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251007121508.1595889-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the performance monitor unit for the Cortex-A55 cores on the
RZ/T2H (R9A09G077) SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251007121508.1595889-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the performance monitor unit for the Cortex-A55 cores on the
RZ/V2N (R9A09G056) SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251007121508.1595889-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the performance monitor unit for the Cortex-A55 cores on the
RZ/V2H(P) (R9A09G057) SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251007121508.1595889-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The ADCs on RZ/T2H and RZ/N2H are exposed on the evaluation kit boards.
Enable them.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251005111323.804638-6-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Renesas RZ/T2H (R9A09G087) includes three 12-Bit successive
approximation A/D converters, two 4-channel ADCs, and one 15-channel
ADC.
Add support for all of them.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251005111323.804638-5-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Renesas RZ/T2H (R9A09G077) includes three 12-Bit successive
approximation A/D converters, two 4-channel ADCs, and one 6-channel ADC.
Add support for all of them.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251005111323.804638-4-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use the more modern adi,adv7180cp compatible for the CVBS input found on
R-Car Gen2 Koelsch boards. This aligns the bindings with the other Gen2
board with the same setup Gose.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251003215318.39757-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
'bus-width' is defined for the corresponding vin input port already.
No need to declare it in the output port again. Fixes:
arch/arm/boot/dts/renesas/r8a7793-gose.dtb: composite-in@20 (adi,adv7180cp): ports:port@3:endpoint: Unevaluated properties are not allowed ('bus-width' was unexpected)
from schema $id: http://devicetree.org/schemas/media/i2c/adi,adv7180.yaml#
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250929093616.17679-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This watchdog can't be used with Linux because the firmware needs it on
V3M boards. Sadly, it doesn't mark the node as reserved, so this is
added manually here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250925093941.8800-26-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This watchdog can't be used with Linux because the firmware needs it on
Ebisu boards. Sadly, it doesn't mark the node as reserved, so this is
added manually here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250925093941.8800-25-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This watchdog can't be used with Linux because the firmware needs it on
Draak boards. Sadly, it doesn't mark the node as reserved, so this is
added manually here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250925093941.8800-24-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This watchdog can't be used with Linux because the firmware needs it on
ULCB boards. Sadly, it doesn't mark the node as reserved, so this is
added manually here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250925093941.8800-23-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This watchdog can't be used with Linux because the firmware needs it on
Salvator boards. Sadly, it doesn't mark the node as reserved, so this is
added manually here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250925093941.8800-22-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>