When userspace passes the SER_RS485_RTS_ON_SEND flag it means that the
CTS_B pin should go to logic level high before the transmission begins.
CTS_B goes to logic level high when both CTSC and CTS bits are cleared.
When userspace passes the SER_RS485_RTS_AFTER_SEND flag it means that the
CTS_B pin should go to logic level low after the transmission finishes.
CTS_B goes to logic level low when CTSC bit is cleared and CTS bit is set.
So fix the CTS_B polarity logic.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a board that needs to drive RTS GPIO high in order to enable the
transmission of a RS485 transceiver the following description is
passed in the devide tree:
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
rts-gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>;
status = "okay";
};
and userspace configures the uart port as follows:
/* enable RS485 mode: */
rs485conf.flags |= SER_RS485_ENABLED;
/* set logical level for RTS pin equal to 1 when sending: */
rs485conf.flags |= SER_RS485_RTS_ON_SEND;
/* set logical level for RTS pin equal to 0 after sending: */
rs485conf.flags &= ~(SER_RS485_RTS_AFTER_SEND);
However the RTS GPIO polarity observed in the oscilloscope is inverted.
When the SER_RS485_RTS_ON_SEND flag is set the imx_port_rts_active()
function should be called and following the same logic when
SER_RS485_RTS_AFTER_SEND flag is cleared the imx_port_rts_inactive()
should be called.
Do such logic change so that RS485 communication in half duplex can
work successfully when the RTS GPIO pin is passed via device tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
*) Add USB HSIC and HS phy driver for Qualcomm's SoC
*) Add USB3 PHY driver for Broadcom NSP SoC
*) Make sun4i-usb-phy driver to be used for V3s USB PHY
*) Misc fixes and cleanups
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=d19A
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.11
*) Add USB HSIC and HS phy driver for Qualcomm's SoC
*) Add USB3 PHY driver for Broadcom NSP SoC
*) Make sun4i-usb-phy driver to be used for V3s USB PHY
*) Misc fixes and cleanups
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The vchi_msg_queue function which is used by other drivers
to queue a message is difficult to understand and overly
generic.
Make the function static and remove it from the exported
symbols.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vchi_msg_queue function which is used by other drivers
to queue a message is difficult to understand and overly
generic.
Add a new function which is a wrapper on top of vchi_msg_queue
that is specifically for queuing a message located in user
address space.
int
vchi_queue_user_message(VCHI_SERVICE_HANDLE_T handle,
void __user *data,
unsigned int size)
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vchi_msg_queue function which is used by other drivers
to queue a message is difficult to understand and overly
generic.
Add a new function which is a wrapper on top of vchi_msg_queue
that is specifically for queuing a message located in kernel
address space.
int
vchi_queue_kernel_message(VCHI_SERVICE_HANDLE_T handle,
void *data,
unsigned int size)
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If safe offline is called for a DASD alias device a null pointer is passed
to fsync_bdev. So check for existence of the blockdevice before calling
fsync_bdev.
Should not be a real world problem since safe offline for an alias device
does not make sense and fsync_bdev can deal with a NULL pointer which it
gets after successful NULL pointer dereferencing on s390.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Check if the device pointer is valid. Just a sanity check since we already
are in the int handler of the device.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow 0 as valid input for the path_threshold attribute to deactivate
the IFCC/CCC error handling.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The device sends data to the audio devices by sending a message with
the data through VC04_SERVICES/VCHIQ. This message contains a
callback pointer that is always filled in with the same function.
This is prone to corruption issues.
Instead fill the callback fields with a fixed cookie value to perforam
some validation on the message response and call the handler function
directly instead of through the callback pointer.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bcm2835-audio driver has a legacy code path for initializing
devices without a device tree. Delete this code path and remove
the non device tree devices.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a TODO list of possible cleanup items.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The principles of operations specifies that the breaking event address
is stored to the address 0x110 in the prefix page only for program checks.
The last branch in user space is lost as soon as a branch in kernel space
is executed after e.g. an svc. This makes it impossible to accurately
maintain the breaking event address for a user space process.
Simplify the code, just copy the current breaking event address from
0x110 to the task structure for program checks from user space.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When some other buffer is immediately copied into allocated region.
Replace calls to kmalloc followed by a memcpy with a direct
call to kmemdup.
Signed-off-by: Shyam Saini <mayhs11saini@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The function dasd_busid() still uses simple_strtoul() to convert a
string to an integer value. This function is obsolete for quite some
time already and should be replaced.
The whole parameter parsing semantic still relies somewhat on the fact,
that simple_strtoul() parses a string containing literals without
complains and just returns the parsed integer value plus the residual
string. kstrtoint(), however, would return -EINVAL in such a case.
Since we want to get rid of simple_strtoul() and now have a nice dasd[]
containing only single elements, we can clean up and simplify a few
things.
Replace simple_strtoul() with kstrtouint(), improve and simplify the
overall parameter parsing by the following:
- instead of residual strings return proper error codes
- remove dasd_parse_next_element() and decide directly what sort of
element is being parsed
- if we parse a device or a range of devices, split that element into
separate bits with a new function
- remove warning about invalid ending as it doesn't apply anymore
- annotate all parsing functions and data that can be freed after
initialisation with __init and __initdata respectively
- clean up bits and pieces while at it
Reviewed-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Jan Höppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the DASD driver is built into the kernel, the entire comma
separated parameter list is stored as one single element in the dasd[]
array, opposed to the module build where each element is stored
separately in dasd[].
There is no point in doing so. Therefore, store each part of the list as
single elements in dasd[] as well when built into the kernel.
Also, create a define for the maximum of 256 parameters.
Reviewed-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Jan Höppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
During tests the Kernel complained about inconsistend lock state:
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
Now all the queue locks use spin_lock_bh/spin_unlock_bh.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The generate_entropy function used a sha256 for compacting
together 256 bits of entropy into 32 bytes hash. However, it
is questionable if a sha256 can really be used here, as
potential collisions may reduce the max entropy fitting into
a 32 byte hash value. So this batch introduces the use of
sha512 instead and the required buffer adjustments for the
calling functions.
Further more the working buffer for the generate_entropy
function has been widened from one page to two pages. So now
1024 stckf invocations are used to gather 256 bits of
entropy. This has been done to be on the save side if the
jitters of stckf values isn't as good as supposed.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In fips mode only xts keys with 128 bit or 125 bit are allowed.
This fix extends the xts_aes_set_key function to check for these
valid key lengths in fips mode.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Triple-DES implementations will soon be required to check
for uniqueness of keys with fips mode enabled. Add checks
to ensure none of the 3 keys match.
Signed-off-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Generated with checkpatch.pl --fix-inplace and git add -p out of the
results.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Generated with checkpatch.pl --fix-inplace, some manual fixes for
cases where checkpatch fixed one out of multiple lines of mis-indented
function parameters, and then git add -p out of the results.
I skipped some fixes that should probably instead be replaced with the
BIT() macro.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is derived from the downstream tree's build system, but with just
a single Kconfig option.
For now the driver only builds on 32-bit arm -- the aarch64 build
breaks due to the driver using arm-specific cache flushing functions.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
49bec49fd7 ("staging: vc04_services: remove vchiq_copy_from_user")
removed the flags/msg_handle arguments, which were unused, and pushed
the implementation of copying using memcpy vs copy_from_user to the
caller.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Supports raw YUV capture, preview, JPEG and H264.
- Uses videobuf2 for data transfer, using dma_buf.
- Uses 3.6.10 timestamping
- Camera power based on use
- Uses immutable input mode on video encoder
This code comes from the Raspberry Pi kernel tree (rpi-4.9.y) as of
a15ba877dab4e61ea3fc7b006e2a73828b083c52.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If dvb_attach() fails then we were just printing an error message and
exiting but the memory allocated to state was not released.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
tx-only RC devices do not have a receive buffer.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
LIRC_SET_REC_TIMEOUT can fail if the value returned by
LIRC_GET_MIN_TIMEOUT is set due to rounding errors.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current message has some wanted spaces on it:
rc_core: Loaded IR protocol module ir-jvc-decoder, but protocol jvc still not available
Merge it into a single line.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
An RC device which is transmit-only shouldn't have the
LIRC_CAN_REC_MODE2 feature.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The GeekBox ships with a 12 button remote control which seems to use the
NEC protocol. The button keycodes were captured with the "ir-keytable"
tool (ir-keytable -p $PROTOCOL -t; human_button_pusher).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds documentation for devicetree bindings for
consumer Mediatek IR controller.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Most IR drivers uses the same label to identify the
scancode/key table they used by multiple bindings and lack
explanation well. So move the shared property into a common
place and give better explanation.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds driver for IR controller on MT7623 SoC.
and should also work on similar Mediatek SoC. Currently
testing successfully on NEC and SONY remote controller
only but it should work on others (lirc, rc-5 and rc-6).
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As reported by kernel build test:
In file included from arch/arm/mach-omap2/pdata-quirks.c:15:0:
>> arch/arm/mach-omap2/pdata-quirks.c:536:49: error: 'rx51_lirc_data' undeclared here (not in a function)
OF_DEV_AUXDATA("nokia,n900-ir", 0, "n900-ir", &rx51_lirc_data),
^
include/linux/of_platform.h:52:21: note: in definition of macro 'OF_DEV_AUXDATA'
.platform_data = _pdata }
^~~~~~
Since "a92def1 [media] ir-rx51: port to rc-core" the build fails on
some arm configurations.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These tests are reversed. A warning should be displayed if an error is
returned, not on success.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fix some spelling typos found in visornic_main.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conversion macros le16_to_cpu was removed and that caused new sparse warning
sparse output:
drivers/staging/wlan-ng/p80211netdev.c:241:44: warning: incorrect type in argument 2 (different base types)
drivers/staging/wlan-ng/p80211netdev.c:241:44: expected unsigned short [unsigned] [usertype] fc
drivers/staging/wlan-ng/p80211netdev.c:241:44: got restricted __le16 [usertype] fc
Fixes: 7ad8257234 ("staging:wlan-ng:Fix sparse warning")
Signed-off-by: Igor Pylypiv <igor.pylypiv@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A style fix across whole driver.
changed permissions to octal style, found using checkpatch
Signed-off-by: Derek Robson <robsonde@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
