Tom Lendacky says:
====================
amd-xgbe: AMD XGBE driver fixes 2017-01-20
This patch series addresses some issues in the AMD XGBE driver.
The following fixes are included in this driver update series:
- Add a fix for a version of the hardware that uses different register
offset values for a device with the same PCI device ID
- Add support to check the return code from the xgbe_init() function
This patch series is based on net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The xgbe_init() routine returns a return code indicating success or
failure, but the return code is not checked. Add code to xgbe_init()
to issue a message when failures are seen and add code to check the
xgbe_init() return code.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A newer version of the hardware is using the same PCI ids for the network
device but has altered register definitions for determining the window
settings for the indirect PCS access. Add support to check for this
hardware and if found use the new register values.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: systemport: Add support for SYSTEMPORT lite
This patch series adds support for SYSTEMPORT Lite which is an evolution
of the existing SYSTEMPORT adapter.
The two generations are largely identical as far as the transmit/receive
path are concerned, and there were just a few control path changes here
and there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add supporf for the SYSTEMPORT Lite Ethernet controller, this piece of hardware
is largely based on the full-blown SYSTEMPORT and differs in the following:
- no full-blown UniMAC, instead we have the MagicPacket matching from UniMAC at
same offset, and a GMII Interface Block (GIB) for the MAC-level stuff, since
we are always interfaced to an Ethernet switch which is fully Ethernet compliant
shortcuts could be made
- 16 transmit queues, whose interrupts are moved into the first Level-2 interrupt
controller bank
- slight TDMA offset change (a register was inserted after TDMA_STATUS, *sigh*)
- 256 RX descriptors (512 words) and 256 TX descriptors (not visible)
As a consequence of these two things, update the code paths accordingly to
differentiate the full-blown from the light version.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding SYSTEMPORT Lite, which has twice as less transmit
queues than SYSTEMPORT make sure we do allocate TX rings based on the
systemport,txq property to get an appropriate memory footprint.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we allocate per cpu storage, let's also use NUMA hints.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the LS mask when setting EEE timer.
LS field is 10 bits long and not 11 as currently.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reported-By: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make the code clearer, use rb_entry() instead of container_of() to
deal with rbtree.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make the code clearer, use rb_entry() instead of container_of() to
deal with rbtree.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86 fix from Thomas Gleixner:
"Restore the retrigger callbacks in the IO APIC irq chips. That
addresses a long standing regression which got introduced with the
rewrite of the x86 irq subsystem two years ago and went unnoticed so
far"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ioapic: Restore IO-APIC irq_chip retrigger callback
Pull smp/hotplug fix from Thomas Gleixner:
"Remove an unused variable which is a leftover from the notifier
removal"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu/hotplug: Remove unused but set variable in _cpu_down()
Random fixes and cleanups that accumulated over the time.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYgTP0AAoJECgfDbjSjVRp0bUH/j2r8TRTPcqIWIixbSSxUtsU
Dp788EyizsPp8kenGPWT7xDQFtuFH2PwAqjvu6ZRa53hvo6Rt4Y8i2S/+lCNt/AN
tzVohWOjlpR6htc44BbJQzJZDHIT9zZKUeYSUBtES0isujBmsrhq7+0lBI3a3FdN
wmYK9LNTMLEo65ycmAulbvYN4iD/b7OqV4dieJCLaGyyrTTEHxfJzTK5f9dLZTz+
fhBofbwoOrdFQg+Ey88wU9xw+Ri31TE6vlwibHzArt46s/Dc7BCFhY7p1vD0uBl/
EIf17jcCB/mzOtmT8EfEhwC2vZYpxbSMaDDGOnSzhlnonkcNbUpII12Y7qEbNjk=
=xkS8
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio/vhost fixes from Michael Tsirkin:
"Random fixes and cleanups that accumulated over the time"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio/s390: virtio: constify virtio_config_ops structures
virtio/s390: add missing \n to end of dev_err message
virtio/s390: support READ_STATUS command for virtio-ccw
tools/virtio/ringtest: tweaks for s390
tools/virtio/ringtest: fix run-on-all.sh for offline cpus
virtio_console: fix a crash in config_work_handler
vhost/scsi: silence uninitialized variable warning
vhost: scsi: constify target_core_fabric_ops structures
Pull thermal management fixes from Zhang Rui:
- fix a regression that thermal zone dynamically allocated sysfs
attributes are freed before they're removed, which is introduced in
4.10-rc1 (Jacob von Chorus)
- fix a boot warning because deprecated hwmon API is used (Fabio
Estevam)
- a couple of fixes for rockchip thermal driver (Brian Norris, Caesar
Wang)
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: rockchip: fixes the conversion table
thermal: core: move tz->device.groups cleanup to thermal_release
thermal: thermal_hwmon: Convert to hwmon_device_register_with_info()
thermal: rockchip: handle set_trips without the trip points
thermal: rockchip: optimize the conversion table
thermal: rockchip: fixes invalid temperature case
thermal: rockchip: don't pass table structs by value
thermal: rockchip: improve conversion error messages
These stand-alone trigger drivers were using iio_trigger_put()
where they should have been using iio_trigger_free(). The
iio_trigger_put() adds a module_put which is bad since they
never did a module_get.
In the sysfs driver, module_get/put's are used as triggers are
added & removed. This extra module_put() occurs on an error path
in the probe routine (probably rare).
In the bfin-timer & interrupt trigger drivers, the module resources
are not explicitly managed, so it's doing a put on something that
was never get'd. It occurs on the probe error path and on the
remove path (not so rare).
Tested with the sysfs trigger driver.
The bfin & interrupt drivers were build tested & inspected only.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reference the newly added vip clock-ids in the clock-tree.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
1) Reverse the test for kmalloc() failure so we can pull everything
back one tab.
2) Use gotos for unwinding.
3) Some of the extra line breaks for the 80 character limit are no
longer needed so we can remove them.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The DHT22 (AM2302) datasheet specifies that the LOW start pulse should not
exceed 20ms. However, observations with an oscilloscope of an RPi Model 2B
(rev 1.1) communicating with a DHT22 sensor showed that the driver was
consistently sending start pulses longer than 20ms:
Kernel 4.7.10-v7+ (n=132):
Minimum pulse length: 20.20ms
Maximum: 29.84ms
Mean: 24.96ms
StDev: 2.82ms
Sensor response rate: 100%
Read success rate: 76%
On kernel 4.8, the start pulse was so long that the sensor would not even
respond 97% of the time:
Kernel 4.8.16-v7+ (n=100):
Minimum pulse length: 30.4ms
Maximum: 74.4ms
Mean: 39.3ms
StDev: 10.2ms
Sensor response rate: 3%
Read success rate: 3%
The driver would return ETIMEDOUT and write log messages like this:
[ 51.430987] dht11 dht11@0: Only 1 signal edges detected
[ 66.311019] dht11 dht11@0: Only 0 signal edges detected
Replacing msleep(18) with usleep_range(18000, 20000) made the pulse length
sane again and restored responsiveness:
Kernel 4.8.16-v7+ with usleep_range (n=123):
Minimum pulse length: 18.16ms
Maximum: 20.20ms
Mean: 19.85ms
StDev: 0.51ms
Sensor response rate: 100%
Read success rate: 84%
Cc: stable@vger.kernel.org
Signed-off-by: John Brooks <john@fastquake.com>
Reviewed-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Pro4 SoC has 2 slots of SD controllers, so 2 pin-mux nodes
(SD and SD1) are needed. The other SoCs have only 1 SD slot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Declare iio_info structures as const as they are only stored in
the info field of a iio_dev structure. This field is of type const,
so iio_info structures having similar properties can be made const too.
File size before:
text data bss dec hex filename
6944 792 0 7736 1e38 drivers/iio/adc/ti-ads1015.o
File size after:
text data bss dec hex filename
7264 472 0 7736 1e38 drivers/iio/adc/ti-ads1015.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Declare device_type structure as const as it is only stored in the
type field of a device structure. This field is of type const, so add
const to declaration of device_type structure.
File size before:
text data bss dec hex filename
5389 208 48 5645 160d iio/industrialio-trigger.o
File size after:
text data bss dec hex filename
5453 176 48 5677 162d iio/industrialio-trigger.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In iio_trigger_write_current() we find the trigger we want while
holding mutex on the list of triggers, but we don't actually do a
get on it while holding mutex. We wait until further validations
are completed and we're sure it's the one we want. Race condition
is that it could be freed by the time we do the get.
Solution is to grab the trigger (iio_trigger_get) as soon as we
find it while holding mutex on the list of triggers. If later
we decide it's not the right one, put it back. (iio_trigger_put).
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds runtime power management support to the isl29028 driver.
It defaults to powering off the device after two seconds of inactivity.
isl29028_chip_init_and_power_on() currently only zeros the CONFIGURE
register on the chip, which will cause the chip to turn off. This patch
also renames that function to isl29028_clear_configure_reg() since it is
now used in several places.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
isl29028_chip_init_and_power_on() calls isl29028_set_als_scale() and
this is not needed until the user actually needs to take a reading from
the ALS/IR sensor. This patch moves the isl29028_set_als_scale() call
from isl29028_chip_init_and_power_on() to isl29028_set_als_ir_mode().
This sets the stage for faster resume times from runtime power
management if the user is only querying the proximity sensor.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
isl29028_chip_init_and_power_on() calls isl29028_set_proxim_sampling()
and this is not needed until the user actually needs to take a proximity
reading. This patch moves the isl29028_set_proxim_sampling() call from
isl29028_chip_init_and_power_on() to isl29028_enable_proximity().
This sets the stage for faster resume times from the runtime power
management if the user is only querying the ALS/IR sensor.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
isl29028_enable_proximity() has a boolean argument named enable. This
function is only called once and the enable flag is set to true in that
call. This patch removes the enable parameter from that function.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
isl29028_write_raw() contains unnecessary parenthesis when checking to
see if the passed in lux scale is valid. This patch removes the
unnecessary parenthesis.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If the call to devm_iio_device_alloc() fails, then isl29028_probe()
logs a message saying that memory cannot be allocated. The user's system
most likely has larger issues at this point. This patch removes that
error message since the error code is passed on and the message is not
necessary.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If the call to isl29028_chip_init_and_power_on() in isl29028_probe()
fails, then isl29028_probe() will log an error message. All of the
error paths in that call path already have error logging in place. This
patch removes the unnecessary logging.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The wording and style of the different error messages was not
consistent. This patch makes the wording and style consistent
throughout the driver.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When isl29028_set_als_scale() fails, it was up to both callers to log
the failure message. This patch moves the logging into
isl29028_set_als_scale() to reduce the overall amount of code in the
driver.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When isl29028_set_proxim_sampling() fails, it was up to both callers to
log the failure message. This patch moves the logging into
isl29028_set_proxim_sampling() to reduce the overall amount of code in
the driver.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The #define ISL29028_DEV_ATTR was not used so this patch removes the
unnecessary code.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add and remove newlines to improve code readability in preparation for
moving the driver out of staging.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The alignment of the variables in the struct isl29028_chip is not
consistent. This changes all of the variables to use consistent
alignment to improve the code readability.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
isl29028_proxim_get() checks to see if the promixity needs to be
enabled on the chip and then calls isl29028_read_proxim(). There
are no other callers of isl29028_read_proxim(). The naming between
these two functions can be confusing so this patch combines the
two to avoid the confusion.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Two separate calls to regmap_update_bits() in isl29028_set_als_scale()
and isl29028_set_als_ir_mode() did not have their function arguments
on the next line aligned correctly to the open parenthesis. This patch
corrects the alignment.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 35ms delays here to use msleep() and
reduce the load on the hrtimer subsystem.
Fixes: commit 4d33615df5 ("iio: light: add MAX30100 oximeter driver support")
Link: http://lkml.org/lkml/2017/1/11/377
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds TI's tlc4541 16-bit ADC driver. Which is a single channel
ADC. Supports raw and trigger buffer access.
Also supports the tlc3541 14-bit device, which has not been tested.
Implementation of the tlc3541 is fairly straight forward thou.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The LD11 SoC is equipped with SD-ctrl (0x59810000) as well as
MIO-ctrl (0x5b3e0000). The SD-ctrl block on this SoC has just
one register for controlling RST_n pin of the eMMC device.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>