Commit bcb6f6d2b9 ("fuse: use timespec64") introduced clamped nsec values
in time_to_jiffies but used the max of nsec and NSEC_PER_SEC - 1 instead of
the min. Because of this, dentries would stay in the cache longer than
requested and go stale in scenarios that relied on their timely eviction.
Fixes: bcb6f6d2b9 ("fuse: use timespec64")
Signed-off-by: David Sheets <dsheets@docker.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: <stable@vger.kernel.org> # 4.9
Reference the newly added isp clock-ids in the clock-tree.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Simplify the interrupt setup by using the new PCI layer helpers.
Despite using pci_enable_msi_range(), this driver was only requesting a
single MSI vector anyway.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Add bias handling for non-GPIO pins for R-Car H3,
- Add drive-strength and bias handling for R-Car M3-W,
- Add CAN, CAN FD, MSIOF, and HSCIF pin groups for R-Car M3-W,
- Add SDHI voltage switching for R-Car M2-N.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=12cM
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.11-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.11
- Add bias handling for non-GPIO pins for R-Car H3,
- Add drive-strength and bias handling for R-Car M3-W,
- Add CAN, CAN FD, MSIOF, and HSCIF pin groups for R-Car M3-W,
- Add SDHI voltage switching for R-Car M2-N.
According to [0], the contribution field for each cooling-device express
their relative power efficiency. Higher weights express higher power
efficiency. Weighting is relative such that if each cooling device has a
weight of 1 they are considered equal. This is particularly useful in
heterogeneous systems where two cooling devices may perform the same kind
of compute, but with different efficiency.
[0] Documentation/thermal/power_allocator.txt
According to Mediatek IC designer, the power efficiency ratio between the
LITTLE core cluster (cooling-device cpu0) and big core cluster
(cooling-device cpu1) is around 3:1 (3072:1024).
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
To support HDMI 4K resolution, mmsys need clcok
mm_sel to be 400MHz.
The board .dts file should override the clock rate
property with the higher VENCPLL frequency the board
supports HDMI 4K resolution.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The struct pinctrl_dev's node field is not properly set up, which means
the .prev and .next fields will be NULL. That's not something that the
linked list code can deal with, so extra care must be taken when using
these fields. An example of this is introduced in commit 3429fb3cda
("pinctrl: Fix panic when pinctrl devices with hogs are unregistered")
where list_del() is made conditional on the pinctrl device being part
of the pinctrl device list. This is to ensure that list_del() won't
crash upon encountering a NULL pointer in .prev and/or .next.
After initializing the list head there's no need to jump through these
extra hoops and list_del() will work unconditionally. This is because
the initialized list head points to itself and therefore the .prev and
.next fields can be properly dereferenced.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit df61b366af26 ("pinctrl: core: Use delayed work for hogs") caused a
regression at least with sh-pfc that is also a GPIO controller as
noted by Geert Uytterhoeven <geert@linux-m68k.org>.
As the original pinctrl_register() has issues calling pin controller
driver functions early before the controller has finished registering,
we can't just revert commit df61b366af26. That would break the drivers
using GENERIC_PINCTRL_GROUPS or GENERIC_PINMUX_FUNCTIONS.
So let's fix the issue with the following steps as a single patch:
1. Revert the late_init parts of commit df61b366af26.
The late_init clearly won't work and we have to just give up
on fixing pinctrl_register() for GENERIC_PINCTRL_GROUPS and
GENERIC_PINMUX_FUNCTIONS.
2. Split pinctrl_register() into two parts
By splitting pinctrl_register() into pinctrl_init_controller()
and pinctrl_create_and_start() we have better control over when
it's safe to call pinctrl_create().
3. Introduce a new pinctrl_register_and_init() function
As suggested by Linus Walleij <linus.walleij@linaro.org>, we
can just introduce a new function for the controllers that need
pinctrl_create() called later.
4. Convert the four known problem cases to use new function
Let's convert pinctrl-imx, pinctrl-single, sh-pfc and ti-iodelay
to use the new function to fix the issues. The rest of the drivers
can be converted later. Let's also update Documentation/pinctrl.txt
accordingly because of the known issues with pinctrl_register().
Fixes: df61b366af26 ("pinctrl: core: Use delayed work for hogs")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using has_capability() rather than ns_capable(), we're no longer using
this header.
Cc: Jike Song <jike.song@intel.com>
Cc: Kirti Wankhede <kwankhede@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Fixes: 9cb07b099fb ("drm/msm: support multiple address spaces")
Reported-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
It would race between userspace thread and commit worker. Ie. vblank
irq would trigger event and userspace could begin the next atomic
update, before the commit worker had a chance to clear the pending
flag.
If we do end up needing something to prevent userspace from trying
another pageflip before getting vblank event, it should probably be
implemented as a pending_planes bitmask, similar to pending_crtcs. See
start_atomic() and end_atomic().
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add mt2701 nand device node, include nfi and bch ecc.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the dtsi node of iommu and smi for mt2701.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch updates my email address as I no longer have access to the old
one.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch rearrange MT2701 DT nodes to keep them in ascending order.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
[mb: fix pio unit address and order]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Station structure is considered as not uploaded
(to driver) until drv_sta_state() finishes. This
call is however done after the structure is
attached to mac80211 internal lists and hashes.
This means mac80211 can lookup (and use) station
structure before it is uploaded to a driver.
If this happens (structure exists, but
sta->uploaded is false) fast_tx path can still be
taken. Deep in the fastpath call the sta->uploaded
is checked against to derive "pubsta" argument for
ieee80211_get_txq(). If sta->uploaded is false
(and sta is actually non-NULL) ieee80211_get_txq()
effectively downgraded to vif->txq.
At first glance this may look innocent but coerces
mac80211 into a state that is almost guaranteed
(codel may drop offending skb) to crash because a
station-oriented skb gets queued up on
vif-oriented txq. The ieee80211_tx_dequeue() ends
up looking at info->control.flags and tries to use
txq->sta which in the fail case is NULL.
It's probably pointless to pretend one can
downgrade skb from sta-txq to vif-txq.
Since downgrading unicast traffic to vif->txq must
not be done there's no txq to put a frame on if
sta->uploaded is false. Therefore the code is made
to fall back to regular tx() op path if the
described condition is hit.
Only drivers using wake_tx_queue were affected.
Example crash dump before fix:
Unable to handle kernel paging request at virtual address ffffe26c
PC is at ieee80211_tx_dequeue+0x204/0x690 [mac80211]
[<bf4252a4>] (ieee80211_tx_dequeue [mac80211]) from
[<bf4b1388>] (ath10k_mac_tx_push_txq+0x54/0x1c0 [ath10k_core])
[<bf4b1388>] (ath10k_mac_tx_push_txq [ath10k_core]) from
[<bf4bdfbc>] (ath10k_htt_txrx_compl_task+0xd78/0x11d0 [ath10k_core])
[<bf4bdfbc>] (ath10k_htt_txrx_compl_task [ath10k_core])
[<bf51c5a4>] (ath10k_pci_napi_poll+0x54/0xe8 [ath10k_pci])
[<bf51c5a4>] (ath10k_pci_napi_poll [ath10k_pci]) from
[<c0572e90>] (net_rx_action+0xac/0x160)
Reported-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TI DA8xx/OMAPL13x/AM17xx/AM18xx SoCs have extra UART registers beyond
the standard 8250 registers, so we need a new compatible string to
indicate this. Also, at least one of these registers uses the full 32
bits, so we need to specify reg-io-width in addition to reg-shift.
"ns16550a" is left in the compatible specification since it does work
as long as the bootloader configures the SoC UART power management
registers.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Tx legacy rate is reported 10 fold, as below
iw dev wlan#N station dump | grep "tx bitrate"
tx bitrate: 240.0 MBit/s
This is because by mistake we multiply by the hardware reported
rate twice by 10, fix this.
Fixes: cec17c3821 ("ath10k: add per peer htt tx stats support for 10.4")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In countries where basic operation of channel 169 is allowed,
this fixes the below WARN_ON_ONCE in Rx and fixes the station
connectivity failure in channel 169 as the packet is dropped
in the driver as the current check limits to channel 165. As of
now all the packets beyond channel 165 is dropped, fix this
by extending the range to channel 169.
Call trace:
drivers/net/wireless/ath/ath10k/wmi.c:1505
ath10k_wmi_event_mgmt_rx+0x278/0x440 [ath10k_core]()
Call Trace:
[<c158f812>] ? printk+0x2d/0x2f
[<c105a182>] warn_slowpath_common+0x72/0xa0
[<f8b67b58>] ? ath10k_wmi_event_mgmt_rx+0x278/0x440
[<f8b67b58>] ? ath10k_wmi_event_mgmt_rx+0x278/0x440
[<c105a1d2>] warn_slowpath_null+0x22/0x30
[<f8b67b58>] ath10k_wmi_event_mgmt_rx+0x278/0x440
[<f8b0e72b>] ? ath10k_pci_sleep+0x8b/0xb0 [ath10k_pci]
[<f8b6ac63>] ath10k_wmi_10_2_op_rx+0xf3/0x3b0
[<f8b6495e>] ath10k_wmi_process_rx+0x1e/0x60
[<f8b5f077>] ath10k_htc_rx_completion_handler+0x347/0x4d0 [ath10k_core]
[<f8b11dc3>] ? ath10k_ce_completed_recv_next+0x53/0x70 [ath10k_pci]
[<f8b0f921>] ath10k_pci_ce_recv_data+0x171/0x1d0 [ath10k_pci]
[<f8b0ec69>] ? ath10k_pci_write32+0x39/0x80 [ath10k_pci]
[<f8b120bc>] ath10k_ce_per_engine_service+0x5c/0xa0 [ath10k_pci]
[<f8b1215f>] ath10k_ce_per_engine_service_any+0x5f/0x70 [ath10k_pci]
[<c1060dc0>] ? local_bh_enable_ip+0x90/0x90
[<f8b1048b>] ath10k_pci_tasklet+0x1b/0x50 [ath10k_pci]
Fixes: 34c30b0a5e ("ath10k: enable advertising support for channel 169, 5Ghz")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently, the common ath9k_common module needs to have a
dependency on RELAY and DEBUG_FS in order to built. This
is usually not a problem. But for RAM and FLASH starved
AR71XX devices, every little bit counts.
This patch adds a new symbol CONFIG_ATH9K_COMMON_DEBUG
which makes it possible to drop the RELAY and DEBUG_FS
dependency there and move it to ATH_(HTC)_DEBUGFS.
Note: The shared FFT/spectral code (which is the only user
of the relayfs in ath9k*) needs DEBUG_FS to export the relayfs
interface to dump the data to userspace. So it makes no sense
to have the functions compiled in, if DEBUG_FS is not there.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 10.4 firmware adds extended peer information to the
firmware's statistics payload. This additional info is
stored as a separate data field and the elements are
stored in their own "peers_extd" list.
These elements can pile up in the same way as the peer
information elements. This is because the
ath10k_wmi_10_4_op_pull_fw_stats() function tries to
pull the same amount (num_peer_stats) for every statistic
data unit.
Fixes: 4a49ae94a4 ("ath10k: fix 10.4 extended peer stats update")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds full VHT160 support for QCA9984 chipsets Tested on Netgear
R7800. 80+80 is possible, but disabled so far since it seems to contain
glitches like missing vht station flags (this may be firmware or mac80211
related).
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
[kvalo@qca.qualcomm.com: refactoring and fix few warnings]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When adding VHT160 support to ath10k_peer_assoc_h_phymode() the VHT mode
selection code becomes too complex. Simplify it by refactoring the vht part to
a separate function.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Definition of cpu ranges are hard to read if the cpu variant is not
zero. Provide MIDR_CPU_VAR_REV() macro to describe the full hardware
revision of a cpu including variant and (minor) revision.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cosmetic change to use phys_addr_t instead of unsigned long for the
return value of __pa_symbol().
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Dmitry Vyukov reported that the syzkaller fuzzer triggered a
deadlock in the vgic setup code when an error was detected, as
the cleanup code tries to take a lock that is already held by
the setup code.
The fix is to avoid retaking the lock when cleaning up, by
telling the cleanup function that we already hold it.
Cc: stable@vger.kernel.org
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Current KVM world switch code is unintentionally setting wrong bits to
CNTHCTL_EL2 when E2H == 1, which may allow guest OS to access physical
timer. Bit positions of CNTHCTL_EL2 are changing depending on
HCR_EL2.E2H bit. EL1PCEN and EL1PCTEN are 1st and 0th bits when E2H is
not set, but they are 11th and 10th bits respectively when E2H is set.
In fact, on VHE we only need to set those bits once, not for every world
switch. This is because the host kernel runs in EL2 with HCR_EL2.TGE ==
1, which makes those bits have no effect for the host kernel execution.
So we just set those bits once for guests, and that's it.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When a VCPU blocks (WFI) and has programmed the vtimer, we program a
soft timer to expire in the future to wake up the vcpu thread when
appropriate. Because such as wake up involves a vcpu kick, and the
timer expire function can get called from interrupt context, and the
kick may sleep, we have to schedule the kick in the work function.
The work function currently has a warning that gets raised if it turns
out that the timer shouldn't fire when it's run, which was added because
the idea was that in that case the work should never have been cancelled.
However, it turns out that this whole thing is racy and we can get
spurious warnings. The problem is that we clear the armed flag in the
work function, which may run in parallel with the
kvm_timer_unschedule->timer_disarm() call. This results in a possible
situation where the timer_disarm() call does not call
cancel_work_sync(), which effectively synchronizes the completion of the
work function with running the VCPU. As a result, the VCPU thread
proceeds before the work function completees, causing changes to the
timer state such that kvm_timer_should_fire(vcpu) returns false in the
work function.
All we do in the work function is to kick the VCPU, and an occasional
rare extra kick never harmed anyone. Since the race above is extremely
rare, we don't bother checking if the race happens but simply remove the
check and the clearing of the armed flag from the work function.
Reported-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Per the discussion of bug fix[1], we now actually
leaves the default clock choice for pcie phy is
derived from 24MHz OSC to guarantee the least BER.
So let's add aspm-no-l0s here and folks could delete
this property from their dts.
[1] https://patchwork.kernel.org/patch/9470519/
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
fuse_abort_conn() moves requests from pending list to a temporary list
before canceling them. This operation races with request_wait_answer()
which also tries to remove the request after it gets a fatal signal. It
checks FR_PENDING flag to determine whether the request is still in the
pending list.
Make fuse_abort_conn() clear FR_PENDING flag so that request_wait_answer()
does not remove the request from temporary list.
This bug causes an Oops when trying to delete an already deleted list entry
in end_requests().
Fixes: ee314a870e ("fuse: abort: no fc->lock needed for request ending")
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: <stable@vger.kernel.org> # 4.2+
Make sure to check for short control transfers in order to avoid parsing
uninitialised buffer data and leaking it to user space.
Note that the backlight and macro-mode buffer constraints are kept as
loose as possible in order to avoid any regressions should the current
buffer sizes be larger than necessary.
Fixes: 6f78193ee9 ("HID: corsair: Add Corsair Vengeance K90 driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Not all platforms support DMA to the stack, and specifically since v4.9
this is no longer supported on x86 with VMAP_STACK either.
Note that the macro-mode buffer was larger than necessary.
Fixes: 6f78193ee9 ("HID: corsair: Add Corsair Vengeance K90 driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some hardware accelerators (like intel aesni or the s390
cpacf functions) have lower priorities than virtio
crypto, and those drivers are faster than the same in
the host via virtio. So let's lower the priority of
virtio-crypto's algorithm, make it's higher than software
implementations but lower than the hardware ones.
Suggested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The ARMv8-M architecture introduces 'tt' and 'ttt' instructions,
which means we can no longer use 'tt' as a register alias on recent
versions of binutils for ARM. So replace the alias with 'ttab'.
Fixes: 81edb42629 ("crypto: arm/aes - replace scalar AES cipher")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add the new register layout constants and the requisite logic
for using them.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since we're going to need to keep track of more than just one
attribute of the hardware, we'll change the use of the data field
from the match struct from a single flag to a struct pointer.
This patch adds the struct template and initial descriptions.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the self-test fails, it probably won't actually suddenly
start working. Currently, this causes an endless spew of
error messages on the console and in the logs, so this patch
adds a limiter to the test.
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fixes the following sparse warning:
drivers/crypto/mediatek/mtk-platform.c:585:27: warning:
symbol 'of_crypto_id' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When working on AES in CCM mode for ARM, my code passed the internal
tcrypt test before I had even bothered to implement the AES-192 and
AES-256 code paths, which is strange because the tcrypt does contain
AES-192 and AES-256 test vectors for CCM.
As it turned out, the define AES_CCM_ENC_TEST_VECTORS was out of sync
with the actual number of test vectors, causing only the AES-128 ones
to be executed.
So get rid of the defines, and wrap the test vector references in a
macro that calculates the number of vectors automatically.
The following test vector counts were out of sync with the respective
defines:
BF_CTR_ENC_TEST_VECTORS 2 -> 3
BF_CTR_DEC_TEST_VECTORS 2 -> 3
TF_CTR_ENC_TEST_VECTORS 2 -> 3
TF_CTR_DEC_TEST_VECTORS 2 -> 3
SERPENT_CTR_ENC_TEST_VECTORS 2 -> 3
SERPENT_CTR_DEC_TEST_VECTORS 2 -> 3
AES_CCM_ENC_TEST_VECTORS 8 -> 14
AES_CCM_DEC_TEST_VECTORS 7 -> 17
AES_CCM_4309_ENC_TEST_VECTORS 7 -> 23
AES_CCM_4309_DEC_TEST_VECTORS 10 -> 23
CAMELLIA_CTR_ENC_TEST_VECTORS 2 -> 3
CAMELLIA_CTR_DEC_TEST_VECTORS 2 -> 3
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ibss and mesh modes copy the ht capabilites from the band without
overriding the SMPS state. Unfortunately the default value 0 for the
SMPS field means static SMPS instead of disabled.
This results in HT ibss and mesh setups using only single-stream rates,
even though SMPS is not supposed to be active.
Initialize SMPS to disabled for all bands on ieee80211_hw_register to
ensure that the value is sane where it is not overriden with the real
SMPS state.
Reported-by: Elektra Wagenrad <onelektra@gmx.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[move VHT TODO comment to a better place]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This replaces the unwieldy generated implementation of bit-sliced AES
in CBC/CTR/XTS modes that originated in the OpenSSL project with a
new version that is heavily based on the OpenSSL implementation, but
has a number of advantages over the old version:
- it does not rely on the scalar AES cipher that also originated in the
OpenSSL project and contains redundant lookup tables and key schedule
generation routines (which we already have in crypto/aes_generic.)
- it uses the same expanded key schedule for encryption and decryption,
reducing the size of the per-key data structure by 1696 bytes
- it adds an implementation of AES in ECB mode, which can be wrapped by
other generic chaining mode implementations
- it moves the handling of corner cases that are non critical to performance
to the glue layer written in C
- it was written directly in assembler rather than generated from a Perl
script
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>