Immediately after successful UFS link startup, UFS link power mode would
be in PWM-G1, 1-lane, SLOW-AUTO mode. But currently we are doing few
of the DME local/peer attributes access before setting the "hba->pwr_info"
to default power mode. If we are doing link startup as part of error
recovery then old power mode might be set to FAST mode and doing DME peer
access (after link startup but before updating "hba->pwr_info" to default
power mode) unintentionally tries to switch from FAST to FAST_AUTO mode (if
UFSHCD_QUIRK_DME_PEER_ACCESS_AUTO_MODE quirk is enabled).
Above issue is fixed by setting the default power mode immediately after
successful link startup.
Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS device requires to perform bkops (back ground operations) periodically
but host can control (via auto-bkops parameter of device) when device can
perform bkops based on its performance requirements. In general, host
would like to enable the device's auto-bkops only when it's not doing any
regular data transfer but sometimes device may not behave properly if host
keeps the auto-bkops disabled. This change adds the capability to let the
device auto-bkops always enabled except suspend.
Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS device and link can be put in multiple different low power modes hence
UFS driver supports multiple different low power modes.
This change sets the default UFS power management level which should put
the link hibernate state and device in sleep state. This default power
management level gives good power savings with relatively less enter/exit
latencies.
Reviewed-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provides the sysfs attribute to choose the power management
level for UFS runtime and system suspend.
Reviewed-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Provide an option to enable/disable clock scaling during runtime.
Write 1/0 to "clkscale_enable" sysfs node to enable/disable clock
scaling.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Provide an option to enable/disable clock gating during runtime.
Write 1 or 0 to "clkgate_enable" sysfs node to enable/disable
clock gating.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a command to a W-LU is timed out via scsi, error handling
will treat it as any other LU and send commands such as
START_STOP with wrong format or task abort. Those commands are
illegal for W-LU according to the UFS spec.
To solve it, when an error is recognized those steps are skipped
and the last step, reset and restore process, is initiated.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change adds the ftrace support for following:
1. UFS initialization time
2. Clock gating states
3. Clock scaling states
4. Power management APIs latency
5. BKOPs enable/disable
Usage:
echo 1 > /sys/kernel/debug/tracing/events/ufs/enable
cat /sys/kernel/debug/tracing/trace_pipe
Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Inserts driver dumps for UFS Host Controller registers, Transfer Requests
and Task Management Requests.
The dumps will occur on driver initialization failure, ufshcd_abort() and
on error handling path.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull i915 drm fixes from Jani Nikula:
"Here's a bunch of drm/i915 fixes for v4.10-rc3. It includes GVT-g
fixes.
My new year's resolution is to start using signed tags for pulls. If
that feels like a déjà vu, it's ((new year's) resolution), not (new
(year's resolution))"
[ Taking this directly from Jani because Dave Airlie is only partially
connected right now. - Linus ]
* tag 'drm-intel-fixes-2017-01-05' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Prevent timeline updates whilst performing reset
drm/i915: Silence allocation failure during sg_trim()
drm/i915: Don't clflush before release phys object
drm/i915: Fix oops in overlay due to frontbuffer tracking
drm/i915: Fix oopses in the overlay code due to i915_gem_active stuff
drm/i915: Initialize overlay->last_flip properly
drm/i915: Move the min_pixclk[] handling to the end of readout
drm/i915: Force VDD off on the new power seqeuencer before starting to use it
drm/i915/gvt: fix typo in cfg_space range check
drm/i915/gvt: fix an issue in emulating cfg space PCI_COMMAND
drm/i915/gvt/kvmgt: trival: code cleanup
drm/i915/gvt/kvmgt: prevent double-release of vgpu
drm/i915/gvt/kvmgt: check returned slot for gfn
drm/i915/gvt/kvmgt: dereference the pointer within lock
drm/i915/gvt: reset the GGTT entry when vGPU created
drm/i915/gvt: fix an error in opregion handling
Some devices do not handle the led brightness or simply don't
care about it. Conceptually said devices want to just switch on
or off the led. It is useless in this case to have a 255 range
of brightness, while just having an LED_ON and LED_OFF improves
the boolean meaning of the led status.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
During my work on some new LED trigger I tried adding example similar to
the existing ones which received following comment from Rob:
> It's not really clear in the example this is an LED node as it is
> incomplete.
Keeping that in mind I suggest adding context for the existing example
entries in hope to make documentation more clear.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
A64 has a MUSB controller wired to the USB PHY 0, which is connected
to the upper USB Type-A port of Pine64.
As the port is a Type-A female port, enable it in host-only mode in the
device tree, which makes devices with USB Type-A male port can work on
this port (which is originally designed by Pine64 team).
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 SoC has a MUSB controller like the one in A33, so add
a node for it, just use the compatible of A33 MUSB.
Host mode is tested to work properly on Pine64 and will be added into
the device tree of Pine64 in next patch.
Peripheral mode is also tested on Pine64, by changing dr_mode property
of usb_otg node and use a non-standard USB Type-A to Type-A cable.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pine64 have two USB Type-A ports, which are wired to the two ports of
A64 USB PHY, and the lower port is the EHCI/OHCI1 port.
Enable the necessary nodes to enable the lower USB port to work.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In this dts file, uart0 node is put before i2c1.
Move the uart0 node to the end to satisfy alphebetical order.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 have two HCI USB controllers, a OTG controller and a USB
PHY device which have two ports. One of the port is wired to both a HCI
USB controller and the OTG controller, which is currently not supported.
The another one is only wired to a HCI controller, and the device node of
OHCI/EHCI controller of the port can be added now.
Also the A64 USB PHY device node is also added for the HCI controllers to
work.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
If we skip before banning, we have an inconsistent interface between
execbuf still queueing valid request but those requests already queued
being cancelled. If we only cancel the pending requests once we stop
accepting new requests, the user interface is more consistent.
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Fixes: 821ed7df6e ("drm/i915: Update reset path to fix incomplete requests")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: <stable@vger.kernel.org> # v4.9+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170105170059.344-1-chris@chris-wilson.co.uk
Now that we have split out a header file for simple macros (that maybe
we can promote into a core header), move a few macros across from
i915_drv.h
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170105164148.26875-1-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Before this patch, the logd daemon only tried to flush things when
the log blocks pinned exceeded a certain threshold. But when we're
deleting very large files, it may require a huge number of journal
blocks, and that, in turn, may exceed the threshold. This patch
factors that into account.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
It's now 2017, and a new LTS kernel has been chosen, so let's do what we
said we would do in the TODO file and delete this code. If it's still
needed, and a maintainer steps up to take it over, we will easily revert
it.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable O and KBUILD_OUTPUT for kselftest. User could compile kselftest
to another directory by passing O or KBUILD_OUTPUT. And O is high
priority than KBUILD_OUTPUT.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Some testcases need the clean extra data after running. This patch
introduce the "EXTRA_CLEAN" variable to address this requirement.
After KBUILD_OUTPUT is enabled in later patch, it will be easy to
decide to if we need do the cleanup in the KBUILD_OUTPUT path(if the
testcase ran immediately after compiled).
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
After previous clean up patches, memfd and timers could get
CROSS_COMPILE from tools/testing/selftest/lib.mk. There is no need to
preserve these definition. So, this patch remove them.
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
There are difference rules for compiling c source file in different
testcases. In order to enable KBUILD_OUTPUT support in later patch,
this patch introduce the default rules in
"tools/testing/selftest/lib.mk" and remove the existing rules in each
testcase.
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
The TEST_DIRS was introduced in Commit e8c1d7cdf1 ("selftests: copy
TEST_DIRS to INSTALL_PATH") for coping a whole directory in ftrace.
After rsync(with -a) is introduced by Commit 900d65ee11 ("selftests:
change install command to rsync"). Rsync could handle the directory
without the definition of TEST_DIRS.
This patch simply replace TEST_DIRS with TEST_FILES in ftrace and remove
the TEST_DIRS in tools/testing/selftest/lib.mk
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Currently, kselftest use TEST_PROGS, TEST_PROGS_EXTENDED, TEST_FILES to
indicate the test program, extended test program and test files. It is
easy to understand the purpose of these files. But mix of compiled and
uncompiled files lead to duplicated "all" and "clean" targets.
In order to remove the duplicated targets, introduce TEST_GEN_PROGS,
TEST_GEN_PROGS_EXTENDED, TEST_GEN_FILES to indicate the compiled
objects.
Also, the later patch will make use of TEST_GEN_XXX to redirect these
files to output directory indicated by KBUILD_OUTPUT or O.
And add this changes to "Contributing new tests(details)" of
Documentation/kselftest.txt.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Fix spelling mistake in print test pass message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Nothing in this minimal script seems to require bash. We often run these
tests on embedded devices where the only shell available is the busybox
ash. Use sh instead.
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Nothing in this minimal script seems to require bash. We often run these
tests on embedded devices where the only shell available is the busybox
ash. Use sh instead.
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
Cc: stable@vger.kernel.org
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Nothing in this minimal script seems to require bash. We often run these
tests on embedded devices where the only shell available is the busybox
ash. Use sh instead.
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Packets from any/all interfaces may be queued up on the PF_PACKET socket
before it is bound to the loopback interface by psock_tpacket, and
when these are passed up by the kernel, they could interfere
with the Rx tests.
Avoid interference from spurious packet by blocking Rx until the
socket filter has been set up, and the packet has been bound to the
desired (lo) interface. The effective sequence is
socket(PF_PACKET, SOCK_RAW, 0);
set up ring
Invoke SO_ATTACH_FILTER
bind to sll_protocol set to ETH_P_ALL, sll_ifindex for lo
After this sequence, the only packets that will be passed up are
those received on loopback that pass the attached filter.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For TCP sockets, TX timestamps are only captured when the user data
is successfully and fully written to the socket. In many cases,
however, TCP writes can be partial for which no timestamp is
collected.
Collect timestamps whenever any user data is (fully or partially)
copied into the socket. Pass tcp_write_queue_tail to tcp_tx_timestamp
instead of the local skb pointer since it can be set to NULL on
the error path.
Note that tcp_write_queue_tail can be NULL, even if bytes have been
copied to the socket. This is because acknowledgements are being
processed in tcp_sendmsg(), and by the time tcp_tx_timestamp is
called tcp_write_queue_tail can be NULL. For such cases, this patch
does not collect any timestamps (i.e., it is best-effort).
This patch is written with suggestions from Willem de Bruijn and
Eric Dumazet.
Change-log V1 -> V2:
- Use sockc.tsflags instead of sk->sk_tsflags.
- Use the same code path for normal writes and errors.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch limits the number of transaction blocks requested during
file truncates. If we have very large multi-terabyte files, and want
to delete or truncate them, they might span so many resource groups
that we overflow the journal blocks, and cause an assert failure.
By limiting the number of blocks in the transaction, we prevent this
overflow and give other running processes time to do transactions.
The limiting factor I chose is sd_log_thresh2 which is currently
set to 4/5ths of the journal. This same ratio is used in function
gfs2_ail_flush_reqd to determine when a log flush is required.
If we make the maximum value less than this, we can get into a
infinite hang whereby the log stops moving because the number of
used blocks is less than the threshold and the iterative loop
needs more, but since we're under the threshold, the log daemon
never starts any IO on the log.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Commit 6995f0b (md: takeover should clear unrelated bits) clear
unrelated bits, but it's quite fragile. To avoid error in the future,
define a macro for unsupported mddev flags for each raid type and use it
to clear unsupported mddev flags. This should be less error-prone.
Suggested-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Trivial fix to spelling mistake "recoverying" to "recovering" in
pr_dbg message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Shaohua Li <shli@fb.com>
r5l_load_log() calls functions that requires a proper conf->log,
for example, r5c_is_writeback(). Therefore, we should set
conf->log before calling r5l_load_log(). If r5l_load_log() fails,
conf->log is set back to NULL.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We only need to update sh->log_start at the end of recovery,
which is r5c_recovery_rewrite_data_only_stripes(), so it is not
necessary to set it before that. In this patch, log_start is
removed from r5c_recovery_alloc_stripe().
After updating all sh->log_start, rewrite_data_only_stripes()
also updates log->next_checkpoints to the last sh->log_start.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The write-through mode has been returned in front of the function,
do not need to do it again.
Signed-off-by: JackieLiu <liuyun01@kylinos.cn>
Reviewed-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
When checking a new device's descriptors, the USB core does not check
for duplicate endpoint addresses. This can cause a problem when the
sysfs files for those endpoints are created; trying to create multiple
files with the same name will provoke a WARNING:
WARNING: CPU: 2 PID: 865 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x8a/0xa0
sysfs: cannot create duplicate filename
'/devices/platform/dummy_hcd.0/usb2/2-1/2-1:64.0/ep_05'
Kernel panic - not syncing: panic_on_warn set ...
CPU: 2 PID: 865 Comm: kworker/2:1 Not tainted 4.9.0-rc7+ #34
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
ffff88006bee64c8 ffffffff81f96b8a ffffffff00000001 1ffff1000d7dcc2c
ffffed000d7dcc24 0000000000000001 0000000041b58ab3 ffffffff8598b510
ffffffff81f968f8 ffffffff850fee20 ffffffff85cff020 dffffc0000000000
Call Trace:
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffff81f96b8a>] dump_stack+0x292/0x398 lib/dump_stack.c:51
[<ffffffff8168c88e>] panic+0x1cb/0x3a9 kernel/panic.c:179
[<ffffffff812b80b4>] __warn+0x1c4/0x1e0 kernel/panic.c:542
[<ffffffff812b8195>] warn_slowpath_fmt+0xc5/0x110 kernel/panic.c:565
[<ffffffff819e70ca>] sysfs_warn_dup+0x8a/0xa0 fs/sysfs/dir.c:30
[<ffffffff819e7308>] sysfs_create_dir_ns+0x178/0x1d0 fs/sysfs/dir.c:59
[< inline >] create_dir lib/kobject.c:71
[<ffffffff81fa1b07>] kobject_add_internal+0x227/0xa60 lib/kobject.c:229
[< inline >] kobject_add_varg lib/kobject.c:366
[<ffffffff81fa2479>] kobject_add+0x139/0x220 lib/kobject.c:411
[<ffffffff82737a63>] device_add+0x353/0x1660 drivers/base/core.c:1088
[<ffffffff82738d8d>] device_register+0x1d/0x20 drivers/base/core.c:1206
[<ffffffff82cb77d3>] usb_create_ep_devs+0x163/0x260 drivers/usb/core/endpoint.c:195
[<ffffffff82c9f27b>] create_intf_ep_devs+0x13b/0x200 drivers/usb/core/message.c:1030
[<ffffffff82ca39d3>] usb_set_configuration+0x1083/0x18d0 drivers/usb/core/message.c:1937
[<ffffffff82cc9e2e>] generic_probe+0x6e/0xe0 drivers/usb/core/generic.c:172
[<ffffffff82caa7fa>] usb_probe_device+0xaa/0xe0 drivers/usb/core/driver.c:263
This patch prevents the problem by checking for duplicate endpoint
addresses during enumeration and skipping any duplicates.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- One fix to the AMD pinctrl ACPI glue.
- Fix requests on the Meson driver.
- Fix bitfield widths on Samsungs Exynos 5433.
-----BEGIN PGP SIGNATURE-----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=t6nv
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Three small pin control fixes for the v4.10 series. Very little to say
about them, just driver fixes.
- one fix to the AMD pinctrl ACPI glue
- fix requests on the Meson driver
- fix bitfield widths on Samsungs Exynos 5433"
* tag 'pinctrl-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: samsung: Fix the width of PINCFG_TYPE_DRV bitfields for Exynos5433
pinctrl: meson: fix gpio request disabling other modes
pinctrl/amd: Set the level based on ACPI tables
The gpiod_get* function family does not want the -gpio suffix.
Use devm_gpiod_get_index_optional instead of devm_gpiod_get_optional.
The descriptor based APIs handle active high/low automatically.
The vbus-gpios are output, request enable while getting the gpio.
Don't try to get any vbus-gpios for ports outside num-ports.
WTF? Big sigh.
Fixes: 054d4b7b57 ("usb: ohci-at91: Use descriptor-based gpio APIs")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christmas break. Most of these are relatively unimportant fixes for
regressions introduced during the merge window, and about half of
the changes are for mach-omap2.
A couple of patches are just cleanups and dead code removal that I would
not normally have considered for merging after -rc2, but I decided to
take them along with the fixes this time.
Notable fixes include:
- removing the skeleton.dtsi include broke a number of machines, and we
have to put empty /chosen nodes back to be able to pass kernel command
lines as before
- enabling Samsung platforms no longer hardwires CONFIG_HZ to 200,
as it had been for no good reason for a long time.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAWG1rP2CrR//JCVInAQLAzg//c0+rQ037TvxWsGl6frL2ogDDbTIDcG8k
t1JZNvD4+E2zV3BZ4mWCOrmGBB02N0ZEERlrHZtshN+OjvzaTgwqTopNoYfkerdR
3ObuxEkfovL0BkRYhC+r9KoiX89koqT6ETDelnKD5UBfeplqUa7kq+MUsGSHq+vo
DkUZJPHeWzSymIe3dnAjY9QaLyCtXgf5c0rakSRbQfnNYGT6dHJZSGMadzg07Aqd
FWOlIds5aE1MsBj18O8i/xylStGWLzOoGJCbF1dOm5rT4fGi9hFIrxkOlTS1a75Z
0S5MoMkgd1cqtOR0s6zZ8KDYemqrnoopqtfDKW3ycpfXyrYbgAnqJB7mfYKi4Vja
Kifgxo6Cz9QoAHrCdQb1MCiiwt9te2lNmT8M+eEaIojunOEJHyoHLmNigDw5MPZu
AgzmukBhENumhQTqPdc0wMuZ+KY1fGGn+DwImHUm/yMGHz1LtnedSfqcgzhNJec9
QmvP0o1nW8m1+kWcJm0vwzP0+TQmEFmqhBWHX9A+Hc1p9dnGqFxWfJoYnfvjTsFf
AmTWvD7UfIF0uHzLOS/wqC6HexFm/XgDtbgx0ug/rEyTTzERc4E0blRfd2du0DH9
XqWgQ/46UZBv5bpzmXkdvQnP1wX6hHNcz0juNVh+71tMeBNCHim4lQIzja2rPqAO
L+r6Ihv4v/Q=
=J2uq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a rather large set of bugfixes, as we just returned from the
Christmas break. Most of these are relatively unimportant fixes for
regressions introduced during the merge window, and about half of the
changes are for mach-omap2.
A couple of patches are just cleanups and dead code removal that I
would not normally have considered for merging after -rc2, but I
decided to take them along with the fixes this time.
Notable fixes include:
- removing the skeleton.dtsi include broke a number of machines, and
we have to put empty /chosen nodes back to be able to pass kernel
command lines as before
- enabling Samsung platforms no longer hardwires CONFIG_HZ to 200, as
it had been for no good reason for a long time"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
MAINTAINERS: extend PSCI entry to cover the newly add PSCI checker code
drivers: psci: annotate timer on stack to silence odebug messages
ARM64: defconfig: enable DRM_MESON as module
ARM64: dts: meson-gx: Add Graphic Controller nodes
ARM64: dts: meson-gxl: fix GPIO include
ARM: dts: imx6: Disable "weim" node in the dtsi files
ARM: dts: qcom: apq8064: Add missing scm clock
ARM: davinci: da8xx: Fix sleeping function called from invalid context
ARM: davinci: Make __clk_{enable,disable} functions public
ARM: davinci: da850: don't add emac clock to lookup table twice
ARM: davinci: da850: fix infinite loop in clk_set_rate()
ARM: i.MX: remove map_io callback
ARM: dts: vf610-zii-dev-rev-b: Add missing newline
ARM: dts: imx6qdl-nitrogen6x: remove duplicate iomux entry
ARM: dts: imx31: fix AVIC base address
ARM: dts: am572x-idk: Add gpios property to control PCIE_RESETn
arm64: dts: vexpress: Support GICC_DIR operations
ARM: dts: vexpress: Support GICC_DIR operations
firmware: arm_scpi: fix reading sensor values on pre-1.0 SCPI firmwares
arm64: dts: msm8996: Add required memory carveouts
...
- small fixes for xenbus driver
- one fix for xen dom0 boot on huge system
- small cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJYbgWzAAoJELDendYovxMvzqQH/iO+SKCrT39q6fCP+fyov7Hi
J67XrHVT/AAPUXizWzKdtBE5EdI+WZXBkdsCEh3+3XPCeCRL/t9dRYEytle0Ioy9
hXC5otiJQ1hhm2N5dQKT5c0IMVh9mAjbeIqcG2dV1lSVaw0CYcJS4xh9eALxj7UY
eXGpNMdNyeiEG2p5OgnDE5GqHavxPh+6ChNxmr8341T8E+C9U1BNtJeUiIQshKmC
YAlt7YWoPzEJeLAYEiwrROYNyrLNd17IlYOeKXSwZUdkVtZahW+/jO+YYmhbx1C/
Yvt93r7ewUFKslRgpZQjjl8y9eynKg+j2BWx8WjAwpdHfCa1DFEOxiAOraLp7Cc=
=ro0H
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.10-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes and cleanups from Juergen Gross:
- small fixes for xenbus driver
- one fix for xen dom0 boot on huge system
- small cleanups
* tag 'for-linus-4.10-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
Xen: ARM: Zero reserved fields of xatp before making hypervisor call
xen: events: Replace BUG() with BUG_ON()
xen: remove stale xs_input_avail() from header
xen: return xenstore command failures via response instead of rc
xen: xenbus driver must not accept invalid transaction ids
xen/evtchn: use rb_entry()
xen/setup: Don't relocate p2m over existing one
Update the Hyper-V MAINTAINERS to include myself.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device gives the following error on detection.
xhci_hcd 0000:00:11.0: ERROR Transfer event for disabled endpoint or
incorrect stream ring
The same error is not seen when it is added to unusual_device
list with US_FL_NO_REPORT_OPCODES passed.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Oliver Neukum <oneukun@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_PM=n:
drivers/usb/core/hub.c:107: warning: ‘hub_usb3_port_prepare_disable’ declared inline after being called
drivers/usb/core/hub.c:107: warning: previous declaration of ‘hub_usb3_port_prepare_disable’ was here
To fix this, move hub_port_disable() after
hub_usb3_port_prepare_disable(), and adjust forward declarations.
Fixes: 37be66767e ("usb: hub: Fix auto-remount of safely removed or ejected USB-3 devices")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>