The driver currently checks the SELF_TEST_FAILED first and then
KERNEL_PANIC next. Under error conditions(boot code failure) both
SELF_TEST_FAILED and KERNEL_PANIC can be set at the same time.
The driver has the capability to reset the controller on an KERNEL_PANIC,
but not on SELF_TEST_FAILED.
Fixed by first checking KERNEL_PANIC and then the others.
Cc: stable@vger.kernel.org
Fixes: e8b12f0fb8 ([SCSI] aacraid: Add new code for PMC-Sierra's SRC base controller family)
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the SMART family of controller panic (KERNEL_PANIC) , they do not
honor IOP resets. So better to skip it and directly perform a IWBR reset.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently driver checks the health status of the adapter once every 24
hours. When that happens the driver becomes dependent on the kernel to
figure out if the adapter is misbehaving. This might take some time
(when the adapter is idle). The driver currently has support to
restart/recover the controller when it fails, and decreasing the time
interval will help.
Fixed by decreasing check interval from 24 hours to 1 minute
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During the IOP reset stress testing, it was found that the drives can be
marked offline when the adapter controller crashes and IO's are running
in parallel. When the controller does come back from the reset, the drive
that is marked offline is not exposed.
Fixed by removing and adding drives that are marked offline. In addition
invoke a scsi host bus rescan to capture any additional configuration
changes.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
aac_command_thread checks on the health of controller periodically,
using aac_check_health. If the status is an error state KERNEL_PANIC or
anything else. The driver will attempt to restart the adapter, but the
response is not checked in aac_command_thread. This allows the periodic
sync to go thru and lead the driver to a hung state.
Fixed by terminating the periodic loop(intended per original design),
if the controller is not restored to a healthy state.
Cc: stable@vger.kernel.org
Fixes: 3d77d84044 (scsi: aacraid: Added support for periodic wellness sync)
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After controller shutdown, all sync fibs time out due to not knowing
about the switch to INT-x mode
Fixed by replacing aac_src_access_devreg() to aac_set_intx_mode() call.
Cc: stable@vger.kernel.org
Fixes: 495c021767 (aacraid: MSI-x support)
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added support to retrieve driver version from a new sysfs variable called
driver_version. It makes it easier for the user to figure out the driver
version that is currently running.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
aac_fib_map_free frees misaligned fib dma memory, additionally it does not
free up the whole memory.
Fixed by changing the code to free up the correct and full memory
allocation.
Cc: stable@vger.kernel.org
Fixes: e8b12f0fb8 ([SCSI] aacraid: Add new code for PMC-Sierra's SRC based controller family)
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arrconf management utility at times sends fibs with AdapterProcessed set
in its fibs. This causes the controller to panic and lockup.
Fixed by failing the commands that have AdapterProcessed set in its flag.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This issue showed up on a kdump debug(single CPU on powerkvm), when EEH
errors rendered the adapter unusable. The driver correctly detected the
issue and attempted to restart the controller, in doing so the driver
attempted to read the status registers of the controller. This triggered
additional eeh errors which continued for a good 6 minutes.
Fixed by returning without waiting when EEH error is reported.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The channel being used for raw srb commands is retrieved from the utility
sent fibs and is converted into physical channel id. The driver does not
need to to do this since the management utility sends the correct channel
id in the first place and in addition the driver sets inaccurate
information in the cmd sent to the firmware and gets an invalid response.
Fixed by using channel id from srb command.
Cc: stable@vger.kernel.org
Fixes: 423400e64d ("scsi: aacraid: Include HBA direct interface")
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replaced camel case with snake case for init supported options.
Suggested-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SECCOMP_RET_KILL filter return code has always killed the current
thread, not the entire process. Changing this as a side-effect of dumping
core isn't a safe thing to do (a few test suites have already flagged this
behavioral change). Instead, restore the RET_KILL semantics, but still
dump core when a RET_KILL delivers SIGSYS to a single-threaded process.
Fixes: b25e67161c ("seccomp: dump core when using SECCOMP_RET_KILL")
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Adds support for detection of the NVMe controller found in the
following recent MacBooks:
- Retina MacBook 2016 (MacBook9,1)
- 13" MacBook Pro 2016 without Touch Bar (MacBook13,1)
- 13" MacBook Pro 2016 with Touch Bar (MacBook13,2)
Signed-off-by: Daniel Roschka <danielroschka@phoenitydawn.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
We can get SYN with zero tsecr, don't apply offset in this case.
Fixes: ee684b6f28 ("tcp: send packets with a socket timestamp")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found that when randomized tcp offsets are enabled (by default)
TCP client can still start new connections without them. Later,
if server does active close and re-uses sockets in TIME-WAIT
state, new SYN from client can be rejected on PAWS check inside
tcp_timewait_state_process(), because either tw_ts_recent or
rcv_tsval doesn't really have an offset set.
Here is how to reproduce it with LTP netstress tool:
netstress -R 1 &
netstress -H 127.0.0.1 -lr 1000000 -a1
[...]
< S seq 1956977072 win 43690 TS val 295618 ecr 459956970
> . ack 1956911535 win 342 TS val 459967184 ecr 1547117608
< R seq 1956911535 win 0 length 0
+1. < S seq 1956977072 win 43690 TS val 296640 ecr 459956970
> S. seq 657450664 ack 1956977073 win 43690 TS val 459968205 ecr 296640
Fixes: 95a22caee3 ("tcp: randomize tcp timestamp offsets for each connection")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This type conversion is a leftover that got ignored during the kcpustat
conversion to nanosecs, resulting in build breakage with config having
CONFIG_NO_HZ_FULL=y.
arch/powerpc/kernel/time.c: In function 'running_clock':
arch/powerpc/kernel/time.c:712:2: error: implicit declaration of function 'cputime_to_nsecs' [-Werror=implicit-function-declaration]
return local_clock() - cputime_to_nsecs(kcpustat_this_cpu->cpustat[CPUTIME_STEAL]);
All we need is to remove it.
Fixes: e7f340ca9c ("powerpc, sched/cputime: Remove unused cputime definitions")
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We will set LPCR with correct value for radix during int. This make sure we
start with a sanitized value of LPCR. In case of kexec, cpus can have LPCR
value based on the previous translation mode we were running.
Fixes: fe036a0605 ("powerpc/64/kexec: Fix MMU cleanup on radix")
Cc: stable@vger.kernel.org # v4.9+
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Optprobes on powerpc are limited to kernel text area. We decided to also
optimize kretprobe_trampoline since that is also in kernel text area.
However,we failed to take into consideration the fact that the same
trampoline is also used to catch function returns from kernel modules.
As an example:
$ sudo modprobe kobject-example
$ sudo bash -c "echo 'r foo_show+8' > /sys/kernel/debug/tracing/kprobe_events"
$ sudo bash -c "echo 1 > /sys/kernel/debug/tracing/events/kprobes/enable"
$ sudo cat /sys/kernel/debug/kprobes/list
c000000000041350 k kretprobe_trampoline+0x0 [OPTIMIZED]
d000000000e00200 r foo_show+0x8 kobject_example
$ cat /sys/kernel/kobject_example/foo
Segmentation fault
With the below (trimmed) splat in dmesg:
Unable to handle kernel paging request for data at address 0xfec40000
Faulting instruction address: 0xc000000000041540
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c000000000041540] optimized_callback+0x70/0xe0
LR [c000000000041e60] optinsn_slot+0xf8/0x10000
Call Trace:
[c0000000c7327850] [c000000000289af4] alloc_set_pte+0x1c4/0x860 (unreliable)
[c0000000c7327890] [c000000000041e60] optinsn_slot+0xf8/0x10000
--- interrupt: 700 at 0xc0000000c7327a80
LR = kretprobe_trampoline+0x0/0x10
[c0000000c7327ba0] [c0000000003a30d4] sysfs_kf_seq_show+0x104/0x1d0
[c0000000c7327bf0] [c0000000003a0bb4] kernfs_seq_show+0x44/0x60
[c0000000c7327c10] [c000000000330578] seq_read+0xf8/0x560
[c0000000c7327cb0] [c0000000003a1e64] kernfs_fop_read+0x194/0x260
[c0000000c7327d00] [c0000000002f9954] __vfs_read+0x44/0x1a0
[c0000000c7327d90] [c0000000002fb4cc] vfs_read+0xbc/0x1b0
[c0000000c7327de0] [c0000000002fd138] SyS_read+0x68/0x110
[c0000000c7327e30] [c00000000000b8e0] system_call+0x38/0xfc
Fix this by loading up the kernel TOC before calling into the kernel.
The original TOC gets restored as part of the usual pt_regs restore.
Fixes: 762df10bad ("powerpc/kprobes: Optimize kprobe in kretprobe_trampoline()")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The f2fs_trim_fs() doesn't need to do checkpoint if there are newly allocated
data blocks only which didn't change the critical checkpoint data such as nat
and sit entries.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
DCCP doesn't purge timewait sockets on network namespace shutdown.
So, after net namespace destroyed we could still have an active timer
which will trigger use after free in tw_timer_handler():
BUG: KASAN: use-after-free in tw_timer_handler+0x4a/0xa0 at addr ffff88010e0d1e10
Read of size 8 by task swapper/1/0
Call Trace:
__asan_load8+0x54/0x90
tw_timer_handler+0x4a/0xa0
call_timer_fn+0x127/0x480
expire_timers+0x1db/0x2e0
run_timer_softirq+0x12f/0x2a0
__do_softirq+0x105/0x5b4
irq_exit+0xdd/0xf0
smp_apic_timer_interrupt+0x57/0x70
apic_timer_interrupt+0x90/0xa0
Object at ffff88010e0d1bc0, in cache net_namespace size: 6848
Allocated:
save_stack_trace+0x1b/0x20
kasan_kmalloc+0xee/0x180
kasan_slab_alloc+0x12/0x20
kmem_cache_alloc+0x134/0x310
copy_net_ns+0x8d/0x280
create_new_namespaces+0x23f/0x340
unshare_nsproxy_namespaces+0x75/0xf0
SyS_unshare+0x299/0x4f0
entry_SYSCALL_64_fastpath+0x18/0xad
Freed:
save_stack_trace+0x1b/0x20
kasan_slab_free+0xae/0x180
kmem_cache_free+0xb4/0x350
net_drop_ns+0x3f/0x50
cleanup_net+0x3df/0x450
process_one_work+0x419/0xbb0
worker_thread+0x92/0x850
kthread+0x192/0x1e0
ret_from_fork+0x2e/0x40
Add .exit_batch hook to dccp_v4_ops()/dccp_v6_ops() which will purge
timewait sockets on net namespace destruction and prevent above issue.
Fixes: f2bf415cfe ("mib: add net to NET_ADD_STATS_BH")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include <sys/socket.h> (guarded by ifndef __KERNEL__) to fix
the following linux/if.h userspace compilation errors:
/usr/include/linux/if.h:234:19: error: field 'ifru_addr' has incomplete type
struct sockaddr ifru_addr;
/usr/include/linux/if.h:235:19: error: field 'ifru_dstaddr' has incomplete type
struct sockaddr ifru_dstaddr;
/usr/include/linux/if.h:236:19: error: field 'ifru_broadaddr' has incomplete type
struct sockaddr ifru_broadaddr;
/usr/include/linux/if.h:237:19: error: field 'ifru_netmask' has incomplete type
struct sockaddr ifru_netmask;
/usr/include/linux/if.h:238:20: error: field 'ifru_hwaddr' has incomplete type
struct sockaddr ifru_hwaddr;
This also fixes userspace compilation of the following uapi headers:
linux/atmbr2684.h
linux/gsmmux.h
linux/if_arp.h
linux/if_bonding.h
linux/if_frad.h
linux/if_pppox.h
linux/if_tunnel.h
linux/netdevice.h
linux/route.h
linux/wireless.h
As no uapi header provides a definition of struct sockaddr, inclusion
of <sys/socket.h> seems to be the most conservative and the only safe
fix available.
All current users of <linux/if.h> are very likely to be including
<sys/socket.h> already because the latter is the sole provider
of struct sockaddr definition in libc, so adding a uapi header
with a definition of struct sockaddr would create a potential
conflict with <sys/socket.h>.
Replacing struct sockaddr in the definition of struct ifreq with
a different type would create a potential incompatibility with current
users of struct ifreq who might rely on ifru_addr et al members being
of type struct sockaddr.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While destroying a network namespace that contains a L2TP tunnel a
"BUG: scheduling while atomic" can be observed.
Enabling lockdep shows that this is happening because l2tp_exit_net()
is calling l2tp_tunnel_closeall() (via l2tp_tunnel_delete()) from
within an RCU critical section.
l2tp_exit_net() takes rcu_read_lock_bh()
<< list_for_each_entry_rcu() >>
l2tp_tunnel_delete()
l2tp_tunnel_closeall()
__l2tp_session_unhash()
synchronize_rcu() << Illegal inside RCU critical section >>
BUG: sleeping function called from invalid context
in_atomic(): 1, irqs_disabled(): 0, pid: 86, name: kworker/u16:2
INFO: lockdep is turned off.
CPU: 2 PID: 86 Comm: kworker/u16:2 Tainted: G W O 4.4.6-at1 #2
Hardware name: Xen HVM domU, BIOS 4.6.1-xs125300 05/09/2016
Workqueue: netns cleanup_net
0000000000000000 ffff880202417b90 ffffffff812b0013 ffff880202410ac0
ffffffff81870de8 ffff880202417bb8 ffffffff8107aee8 ffffffff81870de8
0000000000000c51 0000000000000000 ffff880202417be0 ffffffff8107b024
Call Trace:
[<ffffffff812b0013>] dump_stack+0x85/0xc2
[<ffffffff8107aee8>] ___might_sleep+0x148/0x240
[<ffffffff8107b024>] __might_sleep+0x44/0x80
[<ffffffff810b21bd>] synchronize_sched+0x2d/0xe0
[<ffffffff8109be6d>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff8105c7bb>] ? __local_bh_enable_ip+0x6b/0xc0
[<ffffffff816a1b00>] ? _raw_spin_unlock_bh+0x30/0x40
[<ffffffff81667482>] __l2tp_session_unhash+0x172/0x220
[<ffffffff81667397>] ? __l2tp_session_unhash+0x87/0x220
[<ffffffff8166888b>] l2tp_tunnel_closeall+0x9b/0x140
[<ffffffff81668c74>] l2tp_tunnel_delete+0x14/0x60
[<ffffffff81668dd0>] l2tp_exit_net+0x110/0x270
[<ffffffff81668d5c>] ? l2tp_exit_net+0x9c/0x270
[<ffffffff815001c3>] ops_exit_list.isra.6+0x33/0x60
[<ffffffff81501166>] cleanup_net+0x1b6/0x280
...
This bug can easily be reproduced with a few steps:
$ sudo unshare -n bash # Create a shell in a new namespace
# ip link set lo up
# ip addr add 127.0.0.1 dev lo
# ip l2tp add tunnel remote 127.0.0.1 local 127.0.0.1 tunnel_id 1 \
peer_tunnel_id 1 udp_sport 50000 udp_dport 50000
# ip l2tp add session name foo tunnel_id 1 session_id 1 \
peer_session_id 1
# ip link set foo up
# exit # Exit the shell, in turn exiting the namespace
$ dmesg
...
[942121.089216] BUG: scheduling while atomic: kworker/u16:3/13872/0x00000200
...
To fix this, move the call to l2tp_tunnel_closeall() out of the RCU
critical section, and instead call it from l2tp_tunnel_del_work(), which
is running from the l2tp_wq workqueue.
Fixes: 2b551c6e7d ("l2tp: close sessions before initiating tunnel delete")
Signed-off-by: Ridge Kennedy <ridge.kennedy@alliedtelesis.co.nz>
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the firmware interface spec was updated, a constant element was
renamed. The rename missed the instances in the bnxt_re driver
because it wasn't upstream yet. This updates the bnxt_re driver
with the rename.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Declare bin_attribute structures as const as they are only passed as an
arguments to the functions device_remove_bin_file and
device_create_bin_file. These function arguments are of type const, so
bin_attribute structures having this property can be made const too.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct bin_attribute i@p = {...};
@ok1@
identifier r1.i;
position p,p1;
@@
(
device_remove_bin_file(...,&i@p)
|
device_create_bin_file(..., &i@p1)
)
@bad@
position p!={r1.p,ok1.p,ok1.p1};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct bin_attribute i;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare bin_attribute structures as const as they are only passed as an
arguments to the functions device_remove_bin_file and
device_create_bin_file. These function arguments are of type const, so
bin_attribute structures having this property can be made const too.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct bin_attribute i@p = {...};
@ok1@
identifier r1.i;
position p,p1;
@@
(
device_remove_bin_file(...,&i@p)
|
device_create_bin_file(..., &i@p1)
)
@bad@
position p!={r1.p,ok1.p,ok1.p1};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct bin_attribute i;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds glue-code that allows the EMAC driver to interface
with the existing dt-supported PHYs in drivers/net/phy.
Because currently, the emac driver maintains a small library of
supported phys for in a private phy.c file located in the drivers
directory.
The support is limited to mostly single ethernet transceiver like the:
CIS8201, BCM5248, ET1011C, Marvell 88E1111 and 88E1112, AR8035.
However, routers like the Netgear WNDR4700 and Cisco Meraki MX60(W)
have a 5-port switch (AR8327N) attached to the EMAC. The switch chip
is supported by the qca8k mdio driver, which uses the generic phy
library. Another reason is that PHYLIB also supports the BCM54610,
which was used for the Western Digital My Book Live.
This will now also make EMAC select PHYLIB.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cma_accept_iw() needs to return an error if conn_params is NULL.
Since this is coming from user space, we can crash.
Reported-by: Shaobo He <shaobo@cs.utah.edu>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Cc: stable@vger.kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
This will enable the user to control the specific interface for
connection establishment in case the host has more than 1 interface
under the same subnet.
E.g:
Host interfaces configured as:
- ib0 1.1.1.1/16
- ib1 1.1.1.2/16
Target interfaces configured as:
- ib0 1.1.1.3/16 (listener interface)
- ib1 1.1.1.4/16
the following connect command will go through host iface ib0 (default):
nvme connect -t rdma -n testsubsystem -a 1.1.1.3 -s 1023
but the following command will go through host iface ib1:
nvme connect -t rdma -n testsubsystem -a 1.1.1.3 -s 1023 -w 1.1.1.2
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
According to the preceeding goto, it is likely that 'out_destroy_sq' was
expected here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
This will enable the usage for nvme rdma target.
Also move from a lookup array to a switch statement.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Discovery controllers don't set the values. They are in reserved
areas of the Identify Controller data structure.
Given the cmd completed, the minimal capsule sizes are supported,
so no need to check nqn to detect discovery controllers and
special case validations.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
This driver previously required we have a special check for IO submitted
to nvme IO queues that are temporarily suspended. That is no longer
necessary since blk-mq provides a quiesce, so any IO that actually gets
submitted to such a queue must be ended since the queue isn't going to
start back up.
This is fixing a condition where we have fewer IO queues after a
controller reset. This may happen if the number of CPU's has changed,
or controller firmware update changed the queue count, for example.
While it may be possible to complete the IO on a different queue, the
block layer does not provide a way to resubmit a request on a different
hardware context once the request has entered the queue. We don't want
these requests to be stuck indefinitely either, so ending them in error
is our only option at the moment.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
If a namespace has already been marked dead, we don't want to kick the
request_queue again since we may have just freed it from another thread.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
If the device is not present, the driver should disable the queues
immediately. Prior to this, the driver was relying on the watchdog timer
to kill the queues if requests were outstanding to the device, and that
just delays removal up to one second.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
NVMe devices can advertise multiple power states. These states can
be either "operational" (the device is fully functional but possibly
slow) or "non-operational" (the device is asleep until woken up).
Some devices can automatically enter a non-operational state when
idle for a specified amount of time and then automatically wake back
up when needed.
The hardware configuration is a table. For each state, an entry in
the table indicates the next deeper non-operational state, if any,
to autonomously transition to and the idle time required before
transitioning.
This patch teaches the driver to program APST so that each successive
non-operational state will be entered after an idle time equal to 100%
of the total latency (entry plus exit) associated with that state.
The maximum acceptable latency is controlled using dev_pm_qos
(e.g. power/pm_qos_latency_tolerance_us in sysfs); non-operational
states with total latency greater than this value will not be used.
As a special case, setting the latency tolerance to 0 will disable
APST entirely. On hardware without APST support, the sysfs file will
not be exposed.
The latency tolerance for newly-probed devices is set by the module
parameter nvme_core.default_ps_max_latency_us.
In theory, the device can expose "default" APST table, but this
doesn't seem to function correctly on my device (Samsung 950), nor
does it seem particularly useful. There is also an optional
mechanism by which a configuration can be "saved" so it will be
automatically loaded on reset. This can be configured from
userspace, but it doesn't seem useful to support in the driver.
On my laptop, enabling APST seems to save nearly 1W.
The hardware tables can be decoded in userspace with nvme-cli.
'nvme id-ctrl /dev/nvmeN' will show the power state table and
'nvme get-feature -f 0x0c -H /dev/nvme0' will show the current APST
configuration.
This feature is quirked off on a known-buggy Samsung device.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently, all NVMe quirks are based on PCI IDs. Add a mechanism to
define quirks based on identify_ctrl's vendor id, model number,
and/or firmware revision.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
nvmf_create_ctrl() relys on the presence of a create_crtl callback in the
registered nvmf_transport_ops, so make nvmf_register_transport require one.
Update the available call-sites as well to reflect these changes.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch defines CNS field as 8-bit field and avoids cpu_to/from_le
conversions.
Also initialize nvme_command cns value explicitly to NVME_ID_CNS_NS
for readability (don't rely on the fact that NVME_ID_CNS_NS = 0).
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
No need to dereference req twice to get the cmd when we already
have it stored in a local variable.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Easier for debugging and testing state machine
transitions.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
We usually log the cntlid which is confusing in case
we have multiple subsystems each with it's own cntlid ida.
Instead make cntlid ida globally unique and log the initial
association.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Cleanup of abort flag processing in fcp_op_done.
References were unnecessary
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
trivial fix to spelling mistake in pr_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The wording in the entries were poor and not understandable
by even deities. Kill the selection for default block scheduler,
and impose a policy with sane defaults.
Architected-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Here is the big tty/serial driver patchset for 4.11-rc1.
Not much here, but a lot of little fixes and individual serial driver
updates all over the subsystem. Majority are for the sh-sci driver and
platform (the arch-specific changes have acks from the maintainer).
The start of the "serial bus" code is here as well, but nothing is
converted to use it yet. That work is still ongoing, hopefully will
start to show up across different subsystems for 4.12 (bluetooth is one
major place that will be used.)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWK2lDg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylwfwCgyExa4x8Lur2nZyu8cgcaVRU68VAAoNQh0WJt
EZdEhEkRMt4d64j+ApYI
=iv7x
-----END PGP SIGNATURE-----
Merge tag 'tty-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big tty/serial driver patchset for 4.11-rc1.
Not much here, but a lot of little fixes and individual serial driver
updates all over the subsystem. Majority are for the sh-sci driver and
platform (the arch-specific changes have acks from the maintainer).
The start of the "serial bus" code is here as well, but nothing is
converted to use it yet. That work is still ongoing, hopefully will
start to show up across different subsystems for 4.12 (bluetooth is
one major place that will be used.)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (109 commits)
tty: pl011: Work around QDF2400 E44 stuck BUSY bit
atmel_serial: Use the fractional divider when possible
tty: Remove extra include in HVC console tty framework
serial: exar: Enable MSI support
serial: exar: Move register defines from uapi header to consumer site
serial: pci: Remove unused pci_boards entries
serial: exar: Move Commtech adapters to 8250_exar as well
serial: exar: Fix feature control register constants
serial: exar: Fix initialization of EXAR registers for ports > 0
serial: exar: Fix mapping of port I/O resources
serial: sh-sci: fix hardware RX trigger level setting
tty/serial: atmel: ensure state is restored after suspending
serial: 8250_dw: Avoid "too much work" from bogus rx timeout interrupt
serdev: ttyport: check whether tty_init_dev() fails
serial: 8250_pci: make pciserial_detach_ports() static
ARM: dts: STiH410-b2260: Enable HW flow-control
ARM: dts: STiH407-family: Use new Pinctrl groups
ARM: dts: STiH407-pinctrl: Add Pinctrl group for HW flow-control
ARM: dts: STiH410-b2260: Identify the UART RTS line
dt-bindings: serial: Update 'uart-has-rtscts' description
...
This reverts commit 2cf10cdd48.
The patch has been seen to cause excessive looping.
Reported-by: Olga Kornievskaia <aglo@umich.edu>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: stable@vger.kernel.org # 4.10+
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
