Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-12-07
This series contains updates to i40e and i40evf only.
Filip modifies the i40e to log link speed change and when the link is
brought up and down.
Mitch replaces i40e_txd_use_count() with a new function which is slightly
faster and better documented so the dim witted can better follow the
code. Fixes the locking of the service task so that it is actually
done in the service task and not in the scheduling function which calls
the service task.
Jacob, being the busy little beaver he is, provides most of the changes
starting restores a workaround that is still needed in some configurations,
specifically the Ethernet Controller XL710 for 40GbE QSFP+. Removes
duplicate code and simplifies the i40e_vsi_add_vlan() and
i40e_vsi_kill_vlan() functions. Removes detection of PTP frames over L4
(UDP) on the XL710 MAC, since there was a product decision to defeature
it. Fixed a previous refactor of active filters which caused issues in
the accounting of active_filters. Remaining work was done in the VLAN
filters to improve readability and simplify code as much as possible
to reduce inconsistencies.
Alex fixes foul budget accounting in core code by returning actual
work done, capped to budget-1.
Henry fixes the "ethtool -p" function for 1G BaseT PHYs.
Carolyn adds support for 25G devices for i40e and i40evf.
Michal adds functions to apply the correct access method for external PHYs
which could use Clause22 or Clause45 depending on the PHY.
v2: dropped last patch from previous series, since changes are needed based
on feedback from Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
And simplify the MSI-X logic in general - just request the two vectors
directly instead of going through an indirection table.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nilesh Javali <nilesh.javali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the hip06 and hip07 SoCs, the interrupt lines from the SAS
controllers are connected to mbigen hw module [1]. The mbigen module is
probed with module_init, and, as such, is not guaranteed to probe before
the SAS driver. So we need to support deferred probe.
We check for probe deferral in the hw layer probe, so we not probe into
the main layer and allocate shost, memories, etc., to later learn that
we need to defer the probe.
[1] ./Documentation/devicetree/bindings/interrupt-controller/hisilicon,mbigen-v2.txt
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[mkp: fixed bad indentation]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "google,smaug-rev2" string is missing from the compatible list of
Smaug's DT. The differences of rev2 are not relevant at our current
level of support and it boots just fine, so add it.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the VDD_GPU regulator (a GPIO-enabled PWM regulator) to the Jetson
TX1 board. This addition allows the GPU to be used provided the
bootloader properly enabled the GPU node.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
[as pointed out by Thierry on IRC, nobody has reported a bug
in the field, but using a new bootloader with a .dtb that
has the incorrect data, it will crash on boot]
Fixes: 336f79c7b6 ("arm64: tegra: Add NVIDIA Jetson TX1 Developer Kit support")
Cc: stable@vger.kernel.org #v4.5+
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
NetApp did confirm this is not required.
Cc: Martin George <Martin.George@netapp.com>
Cc: Robert Stankey <Robert.Stankey@netapp.com>
Cc: Steven Schremmer <Steven.Schremmer@netapp.com>
Cc: Sean Stewart <Sean.Stewart@netapp.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Christophe Varoqui <christophe.varoqui@opensvc.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: SCSI ML <linux-scsi@vger.kernel.org>
Cc: device-mapper development <dm-devel@redhat.com>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Reviewed-by: Sean Stewart <sean.stewart@netapp.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If Slot Status indicates changes in both Data Link Layer Status and
Presence Detect, prioritize the Link status change.
When both events are observed, pciehp currently relies on the Slot Status
Presence Detect State (PDS) to agree with the Link Status Data Link Layer
Active status. The Presence Detect State, however, may be set to 1 through
out-of-band presence detect even if the link is down, which creates
conflicting events.
Since the Link Status accurately reflects the reachability of the
downstream bus, the Link Status event should take precedence over a
Presence Detect event. Skip checking the PDC status if we handled a link
event in the same handler.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Add fallback compatibility string for the R-Car Gen 3 family. This is in
keeping with the both the existing fallback compatibility string for the
R-Car Gen 2 family and the fallback scheme being adopted wherever
appropriate for drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Improve readability by listing fallback compatibility strings after the
more-specific compatibility strings they provide a fallback for.
This does not affect run-time behaviour as it is the order in the DTB that
determines which compatibility string is used.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Improve readability by listing fallback compatibility strings after the
more-specific compatibility strings they provide a fallback for.
This does not affect run-time behaviour as it is the order in the DTB that
determines which compatibility string is used.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
put_compat_statfs64() does NOT return -1 and setting errno to EOVERFLOW
when some variables(like: f_bsize) overflowed in the returned struct.
The reason is that the ubuf->f_blocks is __u64 type, it couldn't be
4bits as the judgement in put_comat_statfs64(). Here correct the
__u32 variables(in struct compat_statfs64) for comparison.
reproducer:
step1. mount hugetlbfs with two different pagesize on ppc64 arch.
$ hugeadm --pool-pages-max 16M:0
$ hugeadm --create-mount
$ mount | grep -i hugetlbfs
none on /var/lib/hugetlbfs/pagesize-16MB type hugetlbfs (rw,relatime,seclabel,pagesize=16777216)
none on /var/lib/hugetlbfs/pagesize-16GB type hugetlbfs (rw,relatime,seclabel,pagesize=17179869184)
step2. compile & run this C program.
$ cat statfs64_test.c
#define _LARGEFILE64_SOURCE
#include <stdio.h>
#include <sys/syscall.h>
#include <sys/statfs.h>
int main()
{
struct statfs64 sb;
int err;
err = syscall(SYS_statfs64, "/var/lib/hugetlbfs/pagesize-16GB", sizeof(sb), &sb);
if (err)
return -1;
printf("sizeof f_bsize = %d, f_bsize=%ld\n", sizeof(sb.f_bsize), sb.f_bsize);
return 0;
}
$ gcc -m32 statfs64_test.c
$ ./a.out
sizeof f_bsize = 4, f_bsize=0
Signed-off-by: Li Wang <liwang@redhat.com>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Previous mkfs.f2fs allows small partition inappropriately, so f2fs should detect
that as well.
Refer this in f2fs-tools.
mkfs.f2fs: detect small partition by overprovision ratio and # of segments
Reported-and-Tested-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
SCT Write Same support had been introduced with
commit 7b20309428 ("libata: Add support for SCT Write Same")
Some problems, namely excessive userspace segfaults, had been reported at
http://lkml.kernel.org/r/20160908192736.GA4356@gmail.com
This lead to commit 0ce1b18c42 ("libata: Some drives failing on
SCT Write Same") which strived to disable SCT Write Same on !ZAC devices.
Due to the way this was done and to the logic in sd_config_write_same(),
this didn't work for those devices that have
->max_ws_blocks > SD_MAX_WS10_BLOCKS: for these, ->no_write_same and
->max_write_same_sectors would still be non-zero,
but ->ws10 == ->ws16 == 0. This would cause sd_setup_write_same_cmnd() to
demultiplex REQ_OP_WRITE_SAME requests to WRITE_SAME, and these in turn
aren't supported by libata-scsi:
EXT4-fs (dm-1): Delayed block allocation failed for inode 2625094 at
logical offset 2032 with max blocks 2 with error 121
EXT4-fs (dm-1): This should not happen!! Data will be lost
121 == EREMOTEIO is what scsi_io_completion() asserts in case of
invalid opcodes.
Back to the original problem of userspace segfaults: this can be tracked
down to ata_format_sct_write_same() overwriting the input page. Sometimes,
this page is ZERO_PAGE(0) which ceases to be filled with zeros from that
point on. Since ZERO_PAGE(0) is used for userspace .bss mappings, code of
the following is doomed:
static char *a = NULL; /* .bss */
...
if (a)
*a = 'a';
This problem is not solved by disabling SCT Write Same for !ZAC devices
only.
It can certainly be fixed, but the final release is quite close -- so
disable SCT Write Same for all ATA devices rather than introducing some
SCT key buffer allocation schemes at this point.
Fixes: 7b20309428 ("libata: Add support for SCT Write Same")
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pineview deserves to use its own platform enum (which was already added,
unused, previously). IS_G33() no longer matches Pineview, and gets
replaced by IS_G33() || IS_PINEVIEW() or equivalent. Pineview is no
longer an outlier among platform definitions.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481143689-19672-1-git-send-email-jani.nikula@intel.com
Move deassert of pm/aclk/pclk after phy_init() as we want to optimize the
logic of reset control and reuse rockchip_pcie_init_port() later which
should fully follow the cold boot procedure of ROM code.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Split out a new function, rockchip_cfg_atu(), in order to re-configure the
ATU when missing these information after wakeup from S3.
[bhelgaas: add "dev" temporary, return 0 when known]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
PCIE_RC_CONFIG_LCS contains control and status bits specific to the PCIe
link. The layout for this register looks the same as the existing
PCI_EXP_LNKCTL and PCI_EXP_LNKSTA. So let's reuse them.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We're trying to mask out bits[23:8] while retaining [32:24, 7:0], but we're
doing the inverse. That doesn't have too much effect, since we're setting
all the [23:8] bits to 1, and the other bits are only relevant for modes
we're currently not using. But we should get this right.
Fixes: ca19890840 ("PCI: rockchip: Fix wrong transmitted FTS count")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Per the errata of TRM, the RC can't support L1 substate, so remove the L1
substate cap as well as operation for PCIE_RC_CONFIG_L1_SUBSTATE_CTRL2.
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
rk3399 supports PCIe 2.x link speeds marginally at best, and on some
boards, the link won't train at 5 GT/s at all. Rather than sacrifice 500ms
waiting for training that will never happen, let's use the helper function,
of_pci_get_max_link_speed(), to get the max link speed from DT and specify
link capability.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The calculation of negotiated lanes is wrong: it should be shifted by
PCIE_CORE_PL_CONF_LANE_SHIFT, but it is shifted by
PCIE_CORE_PL_CONF_LANE_MASK instead. Let's fix it.
Fixes: e77f847df5 ("PCI: rockchip: Add Rockchip PCIe controller support")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Allow selection of the Rockchip driver for compile testing, even if we
aren't building for ARCH_ROCKCHIP.
[bhelgaas: changelog]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The default value of common clock configuration is zero indicating
Rockchip's RC is using asynchronous clock architecture but actually we are
using common clock. This will confuse some EP drivers if they need some
different settings referring to this value.
Set the Common Clock Configuration bit in the Link Control Register.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If vpcie3v3 is available, we could provide these information via RC's
configure register to make EP able to know the power limit.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The eLCDIF IP of the i.MX 7 SoC knows multiple clocks and lists them
separately:
Clock Clock Root Description
apb_clk MAIN_AXI_CLK_ROOT AXI clock
pix_clk LCDIF_PIXEL_CLK_ROOT Pixel clock
ipg_clk_s MAIN_AXI_CLK_ROOT Peripheral access clock
All of them are switched by a single gate, which is part of the
IMX7D_LCDIF_PIXEL_ROOT_CLK clock. Hence using that clock also for
the AXI bus clock (clock-name "axi") makes sure the gate gets
enabled when accessing registers.
There seem to be no separate AXI display clock, and the clock is
optional. Hence remove the dummy clock.
This fixes kernel freezes when starting the X-Server (which
disables/re-enables the display controller).
Fixes: e8ed73f691 ("ARM: dts: imx7d: add lcdif support")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
In a previous commit, I made a copy/paste error in the pinmux
definitions of UART3: PG{13,14} instead of PA{13,14}. This commit takes
care of that. I have tested this commit on Orange Pi PC and Orange Pi
Plus, and it works for these boards.
Fixes: e3d11d3c45 ("dts: sun8i-h3: add pinmux definitions for
UART2-3")
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SQob
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.10/defconfig-4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/defconfig
Enable support for MUSB based USB OTG on DA850.
* tag 'davinci-for-v4.10/defconfig-4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci_all_defconfig: Enable da8xx usb otg
Signed-off-by: Olof Johansson <olof@lixom.net>
Add Makefile comments to explain the Kconfig and build strategy for ARM64
drivers that work around not-quite-ECAM issues. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
bias control on DA850.
- Enable high speed support on DA850 MMC/SD
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYRTrHAAoJEGFBu2jqvgRNsk8P/1YZzdGQFXS/JU/09IczFulP
ipYIhV6PdWzYY+yI4L/lFVUqQ9U7ty8CFPDyQuamgp/UpeFqocbVdWY91/kMi0Jr
q3dmNtCC/UM3VeATEli66BiW28MfouW02ZBZWF533gTHb0VoJLaBZLitQzXlJlWg
7cIr73BvyYpSvsSos4yXN94qPYpmjt0OIZtZdfJCLDqS91hTNrNNHtktIUn9U2qB
SlnxIJ4Cfs0hG+cUCJD7u4HkA7XbUkx3Z9UBcbVsGJVQ/6E8x6pbam1vBvUJvp81
aAMw5nmeMBK2xzI2AYjti64gMZTEnAKdYXwvQFuvCJ+i1oSvm5Sv2v0X4fJW5AVF
iTW21sxruUHfYpbTn/NSQ2pAbMtgl23ythm5Utuhq52shfU1/Vtra6NDAPLsbR9H
CvCd2Ao8NgQAcORSyEIKctcVflGjfcUhthVzR/K1TfGm5Y01yj7UvHQ6oXb0PDr0
XW57XFPmYz0/c814Knb7zAKlMQG8dXqmbXWHjybyckxcl4f16055ZMo0crrus1lx
kS5+ju3A+ZPcVcIbrkVEwKbCno06YpoTf1zxQOvhsCBrs1R6rXg8kMysABN4FvoA
9BYEbZA15YiJHqG7AuoBFQ9kejVJgO+YFp20mc3dygVd6w1LgH7gNaCuqSyFPIqx
axucAULZwTlhPcAFEfpr
=w2Ug
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.10/dt-4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
- Add device tree nodes for pin pull-up/pull-down
bias control on DA850.
- Enable high speed support on DA850 MMC/SD
* tag 'davinci-for-v4.10/dt-4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
Signed-off-by: Olof Johansson <olof@lixom.net>
The gic-v3 property redistributor-stride is only meant as a workaround
for broken platforms that have a redistributor stride deviating what the
architecture defines, i.e. 128KiB for GICv3, 256KiB for GICv4. This is
not the case for ZX296718, and redistributor-stride is not really
necessary. Let's drop it.
Also, #redistributor-regions is only required when there is more than
one such region is present. Let's remove it as well.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
GICR for multiple CPU can be described with start address and stride,
or with multiple address. Current multiple address and stride are
both used. Fix it.
vmalloc patch 727a7f5a9 triggered this bug:
[ 0.097146] Unable to handle kernel paging request at virtual address ffff000008060008
[ 0.097150] pgd = ffff000008602000
[ 0.097160] [ffff000008060008] *pgd=000000007fffe003, *pud=000000007fffd003, *pmd=000000007fffc003, *pte=0000000000000000
[ 0.097165] Internal error: Oops: 96000007 [#1] PREEMPT SMP
[ 0.097170] Modules linked in:
[ 0.097177] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.8.0+ #1474
[ 0.097179] Hardware name: ZTE zx296718 evaluation board (DT)
[ 0.097183] task: ffff80003e8c8b80 task.stack: ffff80003e8d0000
[ 0.097197] PC is at gic_populate_rdist+0x74/0x15c
[ 0.097202] LR is at gic_starting_cpu+0xc/0x20
[ 0.097206] pc : [<ffff0000082b1b18>] lr : [<ffff0000082b26e0>] pstate: 600001c5
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull x86 fixes from Ingo Molnar:
"Misc fixes: a core dumping crash fix, a guess-unwinder regression fix,
plus three build warning fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/unwind: Fix guess-unwinder regression
x86/build: Annotate die() with noreturn to fix build warning on clang
x86/platform/olpc: Fix resume handler build warning
x86/apic/uv: Silence a shift wrapping warning
x86/coredump: Always use user_regs_struct for compat_elf_gregset_t
Pull perf fixes from Ingo Molnar:
"A bogus warning fix, a counter width handling fix affecting certain
machines, plus a oneliner hw-enablement patch for Knights Mill CPUs"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Remove invalid warning from list_update_cgroup_even()t
perf/x86: Fix full width counter, counter overflow
perf/x86/intel: Enable C-state residency events for Knights Mill
Pull locking fixes from Ingo Molnar:
"Two rtmutex race fixes (which miraculously never triggered, that we
know of), plus two lockdep printk formatting regression fixes"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
lockdep: Fix report formatting
locking/rtmutex: Use READ_ONCE() in rt_mutex_owner()
locking/rtmutex: Prevent dequeue vs. unlock race
locking/selftest: Fix output since KERN_CONT changes
Pull objtool fix from Ingo Molnar:
"A single late breaking fix for objtool"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix bytes check of lea's rex_prefix
The layout-private data may depend on the layout and/or the inode
still existing when it does post-processing and frees its data, so we
need to free them after calling lrp->ld_private.ops->free().
This fixes a mirror list corruption issue in the flexfiles driver.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
When we're merging an old entry into our new entry, we want to ensure that
we add the list entry in the correct place.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Otherwise the lock context won't be freed when we're done with it.
From: NeilBrown <neilb@suse.com>
Fixes: 5bd3f817 ("NFSv4: change nfs4_select_rw_stateid to take a lock_context inplace of lock_owner")
Signed-off-by: Anna Schumaker <Anna.Schumaker@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
This patch Adds a function to extract intel_crtc_state from the
atomic_state, if not available it returns NULL.
v2 (from Paulo):
- Fix white space problem detected by checkpatch.
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161201154940.24446-7-mahesh1.kumar@intel.com
This patch changes Watermak calculation to fixed point calculation.
Problem with current calculation is during plane_blocks_per_line
calculation we divide intermediate blocks with min_scanlines and
takes floor of the result because of integer operation.
hence we end-up assigning less blocks than required. Which leads to
flickers.
Changes since V1:
- Add fixed point data type as per Paulo's review
Changes since V2:
- use fixed_point instead of fp_16_16
Changes since V3:
- rebase
Changes since V4 (from Paulo):
- My original renaming suggestion was misunderstood, so implement it
- Simplify fixed_16_16_to_u32 implementation
- Fix indentation
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161201154940.24446-6-mahesh1.kumar@intel.com
Display Workarounds #1141
IPC (Isoch Priority Control) may cause underflows.
KBL WA: When IPC is enabled, watermark latency values must be increased
by 4us across all levels. This brings level 0 up to 6us.
Changes since V1:
- Add Workaround number in commit & code
Changes since V2 (from Paulo):
- Bikeshed the WA tag so it looks like the others
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161201154940.24446-4-mahesh1.kumar@intel.com
Display Workarounds #1135
If IPC is enabled in BXT, display underruns are observed.
WA: The Line Time programmed in the WM_LINETIME register should be
half of the actual calculated Line Time.
Programmed Line Time = 1/2*Calculated Line Time
Changes since V1:
- Add Workaround number in commit & code
Changes since V2 (from Paulo):
- Bikeshed white space and make the WA tag look like the others
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161201154940.24446-3-mahesh1.kumar@intel.com
This patch adds variable to check for X_tiled & y_tiled planes, instead
of always checking against framebuffer-modifiers.
Changes:
- Created separate patch as per Paulo's comment
- Added x_tiled variable as well
Changes since V2:
- Incorporate Paulo's comments
- Rebase
Changes since V3 (from Paulo):
- Bikeshed indentation
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161201154940.24446-2-mahesh1.kumar@intel.com